Yes doing new bike to me, my relay clicks... Tested the continuity to the starter button plus stop start red button. My starter were with 12v independent power. You should have 12v+ at the positive side of the starter relay with 30amp fuse. Good luck everyone, keep going.
Hi, 9 years later :) At 2:46 when you say "Jump 12v directly to the low current input terminals of the starter relay", do you mean with a second, external 12v battery, or how? Thanks in advance!
Any battery that’s got a charge will work. Just use the one on ur bike. U won’t use enough electricity to even need to charge it after. Just take two wires and connect them to the positive and negative terminal on ur battery then carefully touch one end of each to where u see he had them in the video.
Hi I hope you can help me…..had a problem with the starter relay first I bought a new one and connected it as it has been.but new is the worst problem I have no spark in the pins and the Mc does not start at all Kawasaki Vn 1500
HELP!!!!! :-) I've got an 05 Suzuki S83 Intruder that I'm having a start issue with. I've noticed (in YT vids) that the low voltage circuit on the starter solenoid shows the 2 wires being in opposite configurations (swapped /opposite) positions. I'm guessing the polarity on the low voltage circuit doesn't matter? TIA Stan in Decatur AL
my prob is the buggie starter turns over but when the sionoid buzzes not clicks i unplug the plug by the silonoid and plug back in it will let the fuelpump kick back on and still wont run any info or ?'s please ask thanks Bob..
I'm late on here, I have kymco xciting 500, it was running fine all these days but I parked it because is been cold these days, I came back to start it after a couple of days it won't start at all, all I hear is a clicking noise close to the battery, I'm going crazy right now I really need help to figure out what is wrong with it
Can a faulty starter relay create a condition where there is no power to the bike? My battery is fully charged, and the main fuse is good. Both checkout with my multimeter. I did not I tested the starter relay for continuity and volts, so I’m thinking the problem lies elsewhere. Thoughts?
Maybe you can help me 2014 Honda FROZA 300 will not start pushing the Starter button, but when you jump the solenoid, the motor would start up and runs fine. This problem was it intermittent for a while, but now it doesn’t start at all. I have to continuously lift the seat up and jump the starter. I have power to the ignition switch all the way down to the solenoid. Also, the kickstand has to be up and the break has to be held to start. Any ideas would help Rob.
You may need a new starter relay. We have a repair manual for this model with all the testing for the starter system, I'll put a link to the sign up page below. www.cyclepedia.com/online-manuals/cyclepedia-honda-online-service-manuals/honda-nss300-forza-scooter-online-service-manual/
Thank you all it turned off to be the rear brake light switch, which is connected to the starting system just waiting on the switch to arrive… Thanks again
Hello, 09 700 rhino, electrical issue between, ignition, fuel pump won't kick on and injector won't fire. Ordered a new relay. Could the ignition cause this? Thank you 😊
I have a benelli tnt 25, and i think i have a power drain in the 2 wires that come out of the ignition switch, so please tell me, does those 2 wires have current ( read 13.2 volts )...... A plus, when i connect my battery, the dashboard lights up briefly, is this a normal operation of the system, or do i have a short circuit?
My bike doesnt start.. starter relay clicks... starter motor no joy... i check Voltage reading batt to relay, all gd, relay to starter motor gd... tried the screw driver trick no spark... what may be the prob? I check Ohm reading from relay to starter motor ots jumpy... does this tells me relay is faulty or motor is faulty?
Can this cause a battery drain ? And horrible whine noise from starter intermitent? My battery get drain8ng and even a new battery drained after 10 days of no use in 20 degree c temp! I fitted a new s solenoid this morn and yad to modify one terminal as it is aftermarket . .the starter wire side i had to drill the hole out and file the side of the terminal..when fitted and new battery charged again it started instantly,then 2nd then a 3rd the whining again but,it started? I feel it is a shit s motor as it is off ebay and my old one never had 1 problem!
@@Cyclepedia vfr 750 1990 I noticed my reg plug is fried from the primary coil loom. The reg is newish aswell but a cheap reg ...one yellow wire had melted to the reg terminal . Also changed the starter as was v noisey clunking etc .. i will do a wire repair and mofset reg on order with wire mods straight to battery mod..
The manual I'm using doesn't say but do you know if a 2014 Honda XR650L starter relay has a fuse in it? There's a fuse slot but it doesn't feel like it's making any contact so I ask myself what's the purpose of having that there. Anyway, I have a clicking noise but no start, took out the starter just for the hell of it and tested it and it works fine any help would be the greatest help I could ever receive. 🤙
Yes, there should be a main fuse and a spare fuse. The spare fuse sits in the fuse box like the others but has no contacts it plugs into. Since you tested the starter motor you may have a bad starter relay.
@@Cyclepedia I even jumped it from the starter to the battery and got nothing, I also jumped across the starter relays terminals and it wouldnt do anything, please something anything you can do
i have a 250 sxf and the battery drains within a few hours.you can hear the fuel pump start up every now and again while its parked up.any ideas of what would be doing this?
Hard to say but if possible look at the wire diagram to see all the components. You may be able to disconnect them one at a time to see what is powering up when it should not.
I have an Aprilia sr50 2001 LC and when i touch the red wire with the battery it tries to start even tho ignition key is not pressed what does this mean?
I just got a zx10r 2016 700miles. The owner before me put about the same on it. He flashed it "I am not a fan of flashing" when I turn the key on it hums but it doesn't stop is that normal? Yours didn't hum did it? I hate this BS flashing. I had a r1 never flashed tuned correct and I walked a supra. Don't belive go look no flash.. Is there anyone selling a stock ECU I have a ecu flashed by Brentuning, flashed for Grave full exhaust KNN Stacks. Let me know.. Stock KRT zx10r 2017
I have a question my 2007 Honda crf150f won’t start whenever I hold the ignition down it clicks once and it don’t do any thing but I can roll start it but if you might know what it is please tell me
The best thing other than this video would be our manual, this will go over testing your starter system so you don't guess and buy the wrong part, here is a link. www.cyclepedia.com/online-manuals/cyclepedia-honda-online-service-manuals/2006-honda-crf150f-online-service-manual/
I have a international 4300 it won’t crank to start I didn’t let the gauge cycle I just stared the truck up instantly and it was about to start and half way stopped I got tech out and checked everything and nothing I got a spn 1081 fmi 9 code
Have a 2008 rhino turn the key nothing , replaced ignition switch started running , back fired a few time when step on gas turn off , now nothing turn key no light on dash ,, nothing ,, check power to switch power good , have no idea , check all fuses , any idea ,,
I have a 2004 yamaha r1. When I turn the key to start i have no power. The starter relay connections look corroded. Could that be my problem. Should I buy a new relay?
As long as the rest of the electrical system is in working order then yes only the electric start would not work but the bike should run using the kick starter.
I have a cbr 900rr 97 bike runs great I don't have the battery cables bolted down but evertimw I take cables off it runs then runs dead is it the battery or could it be cause they ain't bolted down and not enuff connection?
No it should not prevent the lights from turning on, depending on the machine some starter relays have the main fuse in them. If the main fuse is blown then that would stop all power, keep in mind you will need to find out why the main fuse is blown if you replace it and it blows right away and make sure to use the correct fuse.
@@Cyclepedia so first time owning a motorcycle, dicied to get relay just in case .put new one on and still noting . I I was fed up and just began putting everything back together turn key over just one last time and lights came on it even turned on. So far good . Maybe i have a bad ground or something
Usually when this happens the cables on the starter relay are installed backwards or the relay is stuck closed. In either situation the battery voltage is going directly to the starter motor from the battery and bypassing the starter button/starter circuit.
Hey man I hope you can help me out. My bike always turns on but sometimes I have to hold the starter down a bit longer and the start up is kind of weak? Any ideas what the problem could be? Thanks
I have a 2011 Fz8. I also have an intermittent error code 20 which means the atmospheric sensor and air pressure sensor values differ greatly when the key is turned. I thought the weak start was being caused by the error code but I have gotten a weak start even when the code doesn’t come on
What would make the starter motor keep running after the bike starts and the start button is released? And why would it not quit turning the starter after the key was shut off. Mine just did that yesterday. Now it won't start but it clicks when the button it pushed.
@@CyclepediaI have a 02 rsv Mille and have the same issue. Bought brand new Aprilia starter relay and new battery but still cranks after shutting off.🤬🤦♂️🤷♂️
May be a bad relay, recommend doing some diagnostic work to avoid buying the wrong part. Here is a link to our manual. www.cyclepedia.com/online-manuals/yamaha-atv-motorcycle-online-manuals/cyclepedia-yamaha-yfm-660-raptor-service-manual/
I just replaced my starter & starter relay solenoid, checking wires & fuses. My 01 ZX9R is trying to start up whenever I touch the positive cable to the battery🤯it does it with the key in the off position, relay connected or disconnected, start switch on or off. Out of ideas, please help
That’s exactly the issue but I checked the cables from the starter to the solenoid, solenoid to battery & all. I figure the solenoid is stuck but I’ve ran through 4 solenoids in the past months so I’m trying to find the culprit that’s causing the solenoids to malfunction. All my wires, cables & connections look good
Hi there I have a Zongshen gs250cc swapped a new battery bike turns over but not catching spark, swapped a new ignition coil and no spark, any thoughts?
hey I don't know if anyone can help me but when I push down on the floor of my car my dash lights will come on but, when I let go they go off can anybody help me?
I just put my bike away for the winter, and I was using the battery for something, so I had it taken apart, but when I was putting it back together, firstly, I noticed it wouldn't start, as it was electric start only, then I noticed a 7.5 amp fuse wire, this connected directly into the battery, but I noticed it was completely loose, like it was plugged into nothing, could anyone help me on where this is supposed to go? It is also formed to the bike with mud on it so I know it's not just some random cable, also, its a 2015 klx 140L
That is a lot to figure out in the comments, my best suggestion would be signing up for the repair manual, here is a link. www.cyclepedia.com/online-manuals/kawasaki-atv-motorcycle-online-manuals/2008-2011-kawasaki-klx140-motorcycle-online-manual/
Could be many things, you can subscribe to our manual so we can help you troubleshoot. www.cyclepedia.com/online-manuals/cyclepedia-honda-online-service-manuals/honda-nss300-forza-scooter-online-service-manual/
I have a1987 Honda Goldwing Aspencade 1200 something is killing the battery. it arches when I connect the positive side to the battery. I can go for a ride but if I turn the key off it won't start thr bike back up. how do I trouble shoot this problem?
Lance Procter Sr. Procter same problem for my 2010 r1 i can start on with help from other battery but when i go ride then turn it off sa switch then i start on the bike again cant start anymore need to help connect other battery
9929 RR will not start I have done everything new battery new plugs and coil packs tested had rectifier and stator put in all the fuses I'm looking at relays been looking at the relays and I don't know what to do if you could help contact me back thank you
Yes, It was the ignition switch. But it was hard to find out. I had to strip the whole bike, and test cable by cable. If you want to test if it is your ignition just disconnected it. And test your connectors in the inside that casing the goes straight into the wire harness. Use a long cable with Crocodile ends. Connect one end to the positive of your battery and test the connector inside the casing one by one ( There should be three ). Your bike should light up when you touch the right one. If it lights up then it's time to replace your ignition switch.
I'm getting lights on my dash of a 83 Honda nighthawk cb550sc but starter button is not working starter solenoid has been tested and is good. I'm lost on this. Starter works if I jump the starter solenoid.
NICE! you dont know how long I searched that simple troubleshooting tip!! Had similar experience. Road a track day, then various stops along the the way home. Stopped at friends hm.turned of bike enjoyed the eve and when I went out to start it ...nothing. Tore bike apart testing everything. Honda VFR.
Hi I have a problem with my dashboard going dead. When I take out the fuse in the starter motor and replace it all the display comes back. Then when riding the bike it cuts out again doing my head in anyone help
I was having that kind of problem with my cbr600rr. The bike cannot turn on after i put the key one it and turn it on. All indicator on the dashboard is active but cannot start the bike. So i do my check with the fuse etc... it has no problem on it. Finally i got the main problem with my cbr600r 2010. the connector from the key house was rusted and after cleaning it. Now the bike has no problem. btw, the connector place close to the tank in the right side. You need to open the right fairing to get to the connector. It is brown
Great info. So.....uh.....how do I check it again? I don't understand electrical stuff at all. When I click the start button theres no clicking. I tried another switch assembly and still the same. The way I start it and drive is putting a screwdriver To both terminals of the starter relay...so hello anybody in RUclips land have an idea? Ohmmmmmmmm🙏
Your relay can click if it's getting voltage but without positive connection (due to corrosion it a break in the connection) that's all it will do. There are videos on resting starter solenoids/relays if you have a multimeter to check the resistance.
Pls help me my motorcycle when i press the electric start the motorcycle wont on unless you kickstart and when i press the electric start there we be a sound like dozzzzzzzzzzzzzzzzzzzzzz
nice tutorial 👍 idol keep it up please visit channel - THE EXPLORER FOR ALL 1. paano mag repair ng starter relay bubuksan natin 2. paano mag repair ng fuel gauge napundi sa gas 3. paano gumawa ng tester light for continuity 4. paano mag tune up
Sorry sir this tutorial is for automotive mechanics and not for the average person , trying to troubleshoot basic mechanics. For that matter just provide your shops location and a price, not helpful at all just mechanical jargon.. I see perhaps you are trying to simply make a profit by subscribing viewers in You Tube. Please be nice and just claim you are a certified mechanic and attract them to your bussiness.
I'm sorry you did not find this helpful, our business is repair information specifically repair manuals not a shop you bring your vehicle to. We sell repair manuals to customers who choose to work on things and are not trying to scam anyone for any reason.
Excellent explanation all the key aspects in safe starting.🏍🏍🏍
Yes doing new bike to me, my relay clicks...
Tested the continuity to the starter button plus stop start red button.
My starter were with 12v independent power.
You should have 12v+ at the positive side of the starter relay with 30amp fuse.
Good luck everyone, keep going.
Did you find out what is was ?
Hi, 9 years later :) At 2:46 when you say "Jump 12v directly to the low current input terminals of the starter relay", do you mean with a second, external 12v battery, or how? Thanks in advance!
Any battery that’s got a charge will work. Just use the one on ur bike. U won’t use enough electricity to even need to charge it after. Just take two wires and connect them to the positive and negative terminal on ur battery then carefully touch one end of each to where u see he had them in the video.
I have 1993 kawasaki Vulcan 1500. I put it in new battery, it did light everything on but no start up
Great video!!! Very much appreciated by myself and many others. Thanks!
Watch video
😊😊😊😊😊😊😊😊😊😊😊😊
Do you have a answer fory problem
Hi I hope you can help me…..had a problem with the starter relay first I bought a new one and connected it as it has been.but new is the worst problem I have no spark in the pins and the Mc does not start at all Kawasaki Vn 1500
Mine doesnt click just makes a strange shorting sound. Is the relay knackered or something else
Same for mine? I’m about to install the new relay. Have you figured anything out?
@@WillArnold_12 I replaced the relay and it did the same. Put a new battery on and it work straight away
HELP!!!!! :-) I've got an 05 Suzuki S83 Intruder that I'm having a start issue with. I've noticed (in YT vids) that the low voltage circuit on the starter solenoid shows the 2 wires being in opposite configurations (swapped /opposite) positions. I'm guessing the polarity on the low voltage circuit doesn't matter? TIA Stan in Decatur AL
I would recommend following the specific tests for your model in the service manual to avoid confusion.
my prob is the buggie starter turns over but when the sionoid buzzes not clicks i unplug the plug by the silonoid and plug back in it will let the fuelpump kick back on and still wont run any info or ?'s please ask thanks Bob..
I'm late on here, I have kymco xciting 500, it was running fine all these days but I parked it because is been cold these days, I came back to start it after a couple of days it won't start at all, all I hear is a clicking noise close to the battery, I'm going crazy right now I really need help to figure out what is wrong with it
Can a faulty starter relay create a condition where there is no power to the bike? My battery is fully charged, and the main fuse is good. Both checkout with my multimeter. I did not I tested the starter relay for continuity and volts, so I’m thinking the problem lies elsewhere. Thoughts?
Yes trace from tge battery....the starter button plus starter motor...
Thank you sm bro....ur video helped me fix my bike....it was the relay.😊
Glad to hear. Thanks for watching.
What was your bike doing? Mine isn't starting when I push the button. Kickstand is up. Neutral is on
@@jacobbutler7942 same problem, I have a Suzuki Boulevard M50
@@jacobbutler7942 did u manage to fix this problem if so how cause my bike is in exactly the same situation
How about the carbon brush of the starter? Does it contribute?
Excellent ... greetings from Germany
Thanks from Dallas Texas
Maybe you can help me 2014 Honda FROZA 300 will not start pushing the Starter button, but when you jump the solenoid, the motor would start up and runs fine. This problem was it intermittent for a while, but now it doesn’t start at all. I have to continuously lift the seat up and jump the starter. I have power to the ignition switch all the way down to the solenoid. Also, the kickstand has to be up and the break has to be held to start. Any ideas would help Rob.
You may need a new starter relay. We have a repair manual for this model with all the testing for the starter system, I'll put a link to the sign up page below. www.cyclepedia.com/online-manuals/cyclepedia-honda-online-service-manuals/honda-nss300-forza-scooter-online-service-manual/
Thank you all it turned off to be the rear brake light switch, which is connected to the starting system just waiting on the switch to arrive… Thanks again
What if my starter doesn’t cutoff?
Unbolt the battery
Hello, 09 700 rhino, electrical issue between, ignition, fuel pump won't kick on and injector won't fire. Ordered a new relay. Could the ignition cause this? Thank you 😊
If the engine turns over when the key is turned then the starter relay is good. Check to see if you have any fuses that could be blown.
@@Cyclepedia ok, thank you 😊
I have a benelli tnt 25, and i think i have a power drain in the 2 wires that come out of the ignition switch, so please tell me, does those 2 wires have current ( read 13.2 volts )...... A plus, when i connect my battery, the dashboard lights up briefly, is this a normal operation of the system, or do i have a short circuit?
One wire has current, from the battery...once the starter relay moves it gives power to the other side...
Starterul influențează incarcarea bateriei?
all i get is a click when i press the starter button but if i jump the two posts it cranks what does this mean? blown fuse?
My gazer 2004 turns over and starts but dies out after 2seconds it will start again and do the same I've replaced injectors and plugs?
At 1:01 what is that red thing called that connects the the switch?
That is the main fuse cover/plug from the wire harness.
Thanks brother
I have a honda vtx1300c turn the key and the main 20 amp fuse blows everytime help
My start relais doesnt click what could be the problem ??
My bike doesnt start.. starter relay clicks... starter motor no joy... i check Voltage reading batt to relay, all gd, relay to starter motor gd... tried the screw driver trick no spark... what may be the prob? I check Ohm reading from relay to starter motor ots jumpy... does this tells me relay is faulty or motor is faulty?
And i have ordered a new relay just in case. Trying DIY n cheapest fix here... im riding a mv agusta turismo veloce
@@farizyusoff978 did you solve it?
Can this cause a battery drain ? And horrible whine noise from starter intermitent? My battery get drain8ng and even a new battery drained after 10 days of no use in 20 degree c temp!
I fitted a new s solenoid this morn and yad to modify one terminal as it is aftermarket . .the starter wire side i had to drill the hole out and file the side of the terminal..when fitted and new battery charged again it started instantly,then 2nd then a 3rd the whining again but,it started? I feel it is a shit s motor as it is off ebay and my old one never had 1 problem!
No, you have a key off draw somewhere most likely and something wearing out in the starter motor/system depending on what vehicle.
@@Cyclepedia vfr 750 1990
I noticed my reg plug is fried from the primary coil loom. The reg is newish aswell but a cheap reg ...one yellow wire had melted to the reg terminal . Also changed the starter as was v noisey clunking etc .. i will do a wire repair and mofset reg on order with wire mods straight to battery mod..
The manual I'm using doesn't say but do you know if a 2014 Honda XR650L starter relay has a fuse in it? There's a fuse slot but it doesn't feel like it's making any contact so I ask myself what's the purpose of having that there. Anyway, I have a clicking noise but no start, took out the starter just for the hell of it and tested it and it works fine any help would be the greatest help I could ever receive. 🤙
Yes, there should be a main fuse and a spare fuse. The spare fuse sits in the fuse box like the others but has no contacts it plugs into. Since you tested the starter motor you may have a bad starter relay.
@@Cyclepedia I even jumped it from the starter to the battery and got nothing, I also jumped across the starter relays terminals and it wouldnt do anything, please something anything you can do
i have a 250 sxf and the battery drains within a few hours.you can hear the fuel pump start up every now and again while its parked up.any ideas of what would be doing this?
Hard to say but if possible look at the wire diagram to see all the components. You may be able to disconnect them one at a time to see what is powering up when it should not.
I have an Aprilia sr50 2001 LC and when i touch the red wire with the battery it tries to start even tho ignition key is not pressed what does this mean?
Either the relay is stuck in the on position or the lead coming from the battery is on the wrong post
I just got a zx10r 2016 700miles. The owner before me put about the same on it. He flashed it "I am not a fan of flashing" when I turn the key on it hums but it doesn't stop is that normal? Yours didn't hum did it? I hate this BS flashing. I had a r1 never flashed tuned correct and I walked a supra. Don't belive go look no flash.. Is there anyone selling a stock ECU I have a ecu flashed by Brentuning, flashed for Grave full exhaust KNN Stacks. Let me know.. Stock KRT zx10r 2017
Honda ruckus only does click sound I have power everywhere!don't know why electric start not working
I have a question my 2007 Honda crf150f won’t start whenever I hold the ignition down it clicks once and it don’t do any thing but I can roll start it but if you might know what it is please tell me
The best thing other than this video would be our manual, this will go over testing your starter system so you don't guess and buy the wrong part, here is a link.
www.cyclepedia.com/online-manuals/cyclepedia-honda-online-service-manuals/2006-honda-crf150f-online-service-manual/
I have a international 4300 it won’t crank to start I didn’t let the gauge cycle I just stared the truck up instantly and it was about to start and half way stopped I got tech out and checked everything and nothing I got a spn 1081 fmi 9 code
Have a 2008 rhino turn the key nothing , replaced ignition switch started running , back fired a few time when step on gas turn off , now nothing turn key no light on dash ,, nothing ,, check power to switch power good , have no idea , check all fuses , any idea ,,
I would check over the harness and electrical system for any damage or shorts.
I have a 2004 yamaha r1. When I turn the key to start i have no power. The starter relay connections look corroded. Could that be my problem. Should I buy a new relay?
When i tap it i do see some life on my dash panel like the neutral light coming on.
it is possible to start a motorcycle with a broken relay starter... using kick starter?
As long as the rest of the electrical system is in working order then yes only the electric start would not work but the bike should run using the kick starter.
Hi please help. Gen 1 ZX10r No spark
What is the actual values of high and low currents in Amperes? For example the value of current to the solenoid coil
I have a cbr 900rr 97 bike runs great I don't have the battery cables bolted down but evertimw I take cables off it runs then runs dead is it the battery or could it be cause they ain't bolted down and not enuff connection?
Not enough connection
Great starting point .... no pun intended ... but is there a part 2 or 3 I hope because I get the impression you guys know your stuff
If starter relay is not working will that also prevent all lights from turning on?
No it should not prevent the lights from turning on, depending on the machine some starter relays have the main fuse in them. If the main fuse is blown then that would stop all power, keep in mind you will need to find out why the main fuse is blown if you replace it and it blows right away and make sure to use the correct fuse.
@@Cyclepedia so first time owning a motorcycle, dicied to get relay just in case .put new one on and still noting . I I was fed up and just began putting everything back together turn key over just one last time and lights came on it even turned on. So far good . Maybe i have a bad ground or something
I have a 2000 tl 1000r. When I try to hook up the battery the bike trys to turn on without the key plz help
Usually when this happens the cables on the starter relay are installed backwards or the relay is stuck closed. In either situation the battery voltage is going directly to the starter motor from the battery and bypassing the starter button/starter circuit.
Hey man I hope you can help me out. My bike always turns on but sometimes I have to hold the starter down a bit longer and the start up is kind of weak? Any ideas what the problem could be? Thanks
Start with fresh fuel, fully charged battery and make sure all periodic maintenance items are good. What is the bike in question?
I have a 2011 Fz8. I also have an intermittent error code 20 which means the atmospheric sensor and air pressure sensor values differ greatly when the key is turned. I thought the weak start was being caused by the error code but I have gotten a weak start even when the code doesn’t come on
when the cylinoid is crossed startert turns,,, i still do not have power to ignition
ok cool but what if the bike is off and when you connect the battery and the starter turns on and wont shut off
Usually when that happens the relay switch is stuck or hooked up backwards.
Thanks for the tips 👍🏻👍🏻👍🏻👍🏻👍🏻
What would make the starter motor keep running after the bike starts and the start button is released? And why would it not quit turning the starter after the key was shut off. Mine just did that yesterday. Now it won't start but it clicks when the button it pushed.
If everything is hooked up right then the relay is sticking and needs to be replaced.
@@CyclepediaI have a 02 rsv Mille and have the same issue. Bought brand new Aprilia starter relay and new battery but still cranks after shutting off.🤬🤦♂️🤷♂️
Wow. that's the exact info I was after. Thank you for the great video!
What vechicle is that on
A motobike
We bypassed the ignition on a Kawasaki 650 ninja when I cut the bike on it turns right back off it won’t stay on
I have the same problem
Legend. I wouldn't of known that my moped had another fuse if it wasnt for this video. Thankyou sir
I have a 05 raptor 660r and the starter relay just makes buzzing sound. What the problem??
Is the battery fully charged? A weak battery will do this.
I was using jumping cables with my car running. The car has a brand new battery too.
May be a bad relay, recommend doing some diagnostic work to avoid buying the wrong part. Here is a link to our manual. www.cyclepedia.com/online-manuals/yamaha-atv-motorcycle-online-manuals/cyclepedia-yamaha-yfm-660-raptor-service-manual/
I just replaced my starter & starter relay solenoid, checking wires & fuses. My 01 ZX9R is trying to start up whenever I touch the positive cable to the battery🤯it does it with the key in the off position, relay connected or disconnected, start switch on or off. Out of ideas, please help
Sounds like the cables are wrong, you must have battery voltage going straight to the starter motor.
That’s exactly the issue but I checked the cables from the starter to the solenoid, solenoid to battery & all. I figure the solenoid is stuck but I’ve ran through 4 solenoids in the past months so I’m trying to find the culprit that’s causing the solenoids to malfunction. All my wires, cables & connections look good
@@YungCountry1 Are you using a Kawasaki relay or an aftermarket brand. I have had this problem when using cheap relays.
CYCLEPEDIA Service Manuals aftermarket eBay bought, I fixed it though, solenoid sticking was the issue
Hi there
I have a Zongshen gs250cc swapped a new battery bike turns over but not catching spark, swapped a new ignition coil and no spark, any thoughts?
Jose Arellano did u get it going
hey I don't know if anyone can help me but when I push down on the floor of my car my dash lights will come on but, when I let go they go off can anybody help me?
What if i connect direct the break senzors , test every component , and still don t work ?
I just put my bike away for the winter, and I was using the battery for something, so I had it taken apart, but when I was putting it back together, firstly, I noticed it wouldn't start, as it was electric start only, then I noticed a 7.5 amp fuse wire, this connected directly into the battery, but I noticed it was completely loose, like it was plugged into nothing, could anyone help me on where this is supposed to go? It is also formed to the bike with mud on it so I know it's not just some random cable, also, its a 2015 klx 140L
That is a lot to figure out in the comments, my best suggestion would be signing up for the repair manual, here is a link. www.cyclepedia.com/online-manuals/kawasaki-atv-motorcycle-online-manuals/2008-2011-kawasaki-klx140-motorcycle-online-manual/
My ruckus ps250 star but engine does not running
i have an issue with the ignition fuse blowing as soon as you turn the kill switch to run, can the starter solenoid cause this issue?
coil gone down my gsx600f did this i went through it with a fine tooth comb this is what i came up with
Mud Flap Guy
Mud Flap Guy answer the qiestiom
I have this issue my fuse keeps blowing. So you cleaning it fixed it?
What is the reason for the appearance of a red light (FI) on a Honda Forza motorcycle?
Could be many things, you can subscribe to our manual so we can help you troubleshoot.
www.cyclepedia.com/online-manuals/cyclepedia-honda-online-service-manuals/honda-nss300-forza-scooter-online-service-manual/
My 2013 ford edge is not cranking and not starting the notification on the instrument panel says starting system fault. Please help
I have the same problem with my 2013 Ford Taurus. Did you find the problem?
I have a1987 Honda Goldwing Aspencade 1200
something is killing the battery. it arches when I connect the positive side to the battery. I can go for a ride but if I turn the key off it won't start thr bike back up. how do I trouble shoot this problem?
Lance Procter Sr. Procter same problem for my 2010 r1 i can start on with help from other battery but when i go ride then turn it off sa switch then i start on the bike again cant start anymore need to help connect other battery
How old is your battery ?
9929 RR will not start I have done everything new battery new plugs and coil packs tested had rectifier and stator put in all the fuses I'm looking at relays been looking at the relays and I don't know what to do if you could help contact me back thank you
My Honda Magna is not giving me anything, no lights, no iginition, nothing. Could it be the ignition relay? Battery is good, rectifier is good.
Gerardo Aviles same problem for me, Did you find out what was wrong with yours?
Yes, It was the ignition switch. But it was hard to find out. I had to strip the whole bike, and test cable by cable. If you want to test if it is your ignition just disconnected it. And test your connectors in the inside that casing the goes straight into the wire harness. Use a long cable with Crocodile ends. Connect one end to the positive of your battery and test the connector inside the casing one by one ( There should be three ). Your bike should light up when you touch the right one. If it lights up then it's time to replace your ignition switch.
Remember!! Your battery should be connected to the system. Positive and negative. Ride on!!!
I'm getting lights on my dash of a 83 Honda nighthawk cb550sc but starter button is not working starter solenoid has been tested and is good. I'm lost on this. Starter works if I jump the starter solenoid.
NICE! you dont know how long I searched that simple troubleshooting tip!! Had similar experience. Road a track day, then various stops along the the way home. Stopped at friends hm.turned of bike enjoyed the eve and when I went out to start it ...nothing. Tore bike apart testing everything. Honda VFR.
My drz 400 fuse is burned. Bike is runing for 5 seconds then dies, and bogging.
You may need to look for a short or wiring issue especially if you replace the fuse and it blows again.
I have a vespa LX 150, the dynamo starter start and continue turn on until the battery is runs out of power.. is the Starter relay is the problem?
Yes
Hi I have a problem with my dashboard going dead. When I take out the fuse in the starter motor and replace it all the display comes back. Then when riding the bike it cuts out again doing my head in anyone help
Sounds like you might have a loose connection or short somewhere.
Excellent video
I was having that kind of problem with my cbr600rr. The bike cannot turn on after i put the key one it and turn it on. All indicator on the dashboard is active but cannot start the bike.
So i do my check with the fuse etc... it has no problem on it.
Finally i got the main problem with my cbr600r 2010. the connector from the key house was rusted and after cleaning it. Now the bike has no problem. btw, the connector place close to the tank in the right side. You need to open the right fairing to get to the connector. It is brown
Got water in my grandson now it wont go please tell me wots up we it
oh no not the grandson
I have a 1986 helix..it runs..but I have no current to..the starter switch button ..the headlight..fuel guage
Have you checked the fuses in the glove box.
Great info. So.....uh.....how do I check it again? I don't understand electrical stuff at all. When I click the start button theres no clicking. I tried another switch assembly and still the same. The way I start it and drive is putting a screwdriver
To both terminals of the starter relay...so hello anybody in RUclips land have an idea?
Ohmmmmmmmm🙏
Why engine is not turning off
MAn my starter keep turning even if I turn the switch off or the kill switch as soon as I touch the battery cable please help
Are the cables hooked up properly? From battery to starter? I have seen switches fail like that especially cheap replacements.
Tick tick tick that all I hear coming from my moped when I try and start
Which is it Solenoid or starter ? The ticking sounds like the Solenoid
Your relay can click if it's getting voltage but without positive connection (due to corrosion it a break in the connection) that's all it will do. There are videos on resting starter solenoids/relays if you have a multimeter to check the resistance.
yeah same problem
Why does it show 20 fuse and not 15
Main fuse size can vary by model.
Lighting diagram
Good info, thanks.
Thanks.
Put in new battery in a 2003 Honda shadow nothing works. No lights or anything. Suggestions
Pls help me my motorcycle when i press the electric start the motorcycle wont on unless you kickstart and when i press the electric start there we be a sound like dozzzzzzzzzzzzzzzzzzzzzz
Is the battery charged?
Mine i turn my key and the dash dont turn on
Check your main fuse if applicable
@@Cyclepedia ok ima do that if it doesn't work ima coment again
@@Cyclepedia could i reach u on any social media
@chinggis83 Have you checked for loose connections? Make sure the battery is hooked up correctly as well
Thanks realy help to me i fix my boulevard 05
Thank you sir
nice and clear. thanks
My 2015 Kawasaki brute force turn over but want start
Check for spark and fuel
Artic cat coil connection
nice tutorial 👍 idol keep it up
please visit channel - THE EXPLORER FOR ALL
1. paano mag repair ng starter relay bubuksan natin
2. paano mag repair ng fuel gauge napundi sa gas
3. paano gumawa ng tester light
for continuity
4. paano mag tune up
Tnx’!!!!!
Awsome
I can't understand your language. Please, speak in Indian language hindi. Thankyou.
Sorry sir this tutorial is for automotive mechanics and not for the average person , trying to troubleshoot basic mechanics. For that matter just provide your shops location and a price, not helpful at all just mechanical jargon.. I see perhaps you are trying to simply make a profit by subscribing viewers in You Tube. Please be nice and just claim you are a certified mechanic and attract them to your bussiness.
I'm sorry you did not find this helpful, our business is repair information specifically repair manuals not a shop you bring your vehicle to. We sell repair manuals to customers who choose to work on things and are not trying to scam anyone for any reason.
Next time, do the video in English.
Next time, fuck off and find a video in English... Thanks 🖕
Too simple a video. No useful info here. Waste of your time and mine.
Sorry this was not up to your you tube standards Jeff
@@Cyclepedia I found it useful.
Find it useful in 2019, thanks creator.
@@Cyclepedia it is usefull my wr450f is running again
Glen Byrne thanks for the tips, keep them coming!
meh
bridge relay and bike cranks. no lights on dash and bike doesnt start. any idea?
My starter motor is going backwards after I connected the live and Earth the wrong way round, can this be put right?