Fantastic Tools From The Toolroom #1 Precision Vises
HTML-код
- Опубликовано: 4 сен 2024
- In this video we take a look at precision grinding vises. We examine some of the vises in my collection and discuss features and different uses. If your looking to buy a precision grinding vise this video should be helpful. Let me know in the comments what tools you would like to see in the next installment of tools from the toolroom.
The only complaint I have about Tom's videos is there's not enough of them... Though they are a bit like crack, so low volume means I can be a functioning addict.
Loaning out a vise:
Once I had a bunch of little parts to fettle, so I stopped at Sears and bought a Craftsman vacuum-base vise with 2.5" jaws and soft jaw pads. It probably cost less than $20, and did the job nicely. One of my coworkers walked by my desk,saw what I was doing and asked to borrow the vise when I was done with it. When I gave it to him I asked him to be careful with it because it was my personal property, not owned by our company. When he returned it to me, the soft jaws were trashed. I kinda blew my stack. He just looked at me and said, "Well, I had a job to do!"
Several years later, I was using my brand new Mitutoyo digital calipers and Mr. Vise-Destroyer asked to borrow them when I was finished. You would think I had learned a lesson from the vise...
It's no coincidence that the guy who wrecks tools is also the guy that always needs to borrow something... 8-)
My lesson came when apprentice asked to borrow a scriber. I reluctantly handed over my starrett carbide tipped scribed. 10 mins later, Intrigued as to what he was doing with it found him chipping out a broken centre drill. 😳
In 37 years, I have never loaned out my Hermann Schmidt grinding vise. I paid a lot of money for when I was an apprentice and if somebody is going to put a gash into it, it's going to be me. So far it's as good as new.
one time a guy came over to me with a broken tool and asked if he could borrow my tool like it. I gave him a funny look and said no. He said, I'm not going to break it. I replied, that's right, because you're not going to borrow it.
Thank you, Tom. Your introductory speech tells it all. You're very generous for sharing your knowledge and explaining the neat tools machinists use.
That vice from Steve is a beauty. I recognized it imeaditly by his star shaped logo. Anybody interested in this type of thing should take a look at the video you did covering the tooling that he made. Top notch workmanship!!
Great grasp of the vise situation. Thanks for the video.
Fun video, Tom. You answered a question I had about a Hermann Schmidt vise I had picked up. I observed the few tenths out of square, and wondered. But, when you pointed out the reasoning, it was a head-slapper.
Love the Intro Tom! Also a nice collection of vises.
ATB, Robin
oh god. please find time to do more. really good to get a video from you.
Love it...I can't get over how cool your shop is and your knowledge Tom! Long time no see!
Every time I think about how I wish Tom uploaded more frequently I think of two things: 1) editing and uploading content is a PITA; and 2) Tom is probably doing really cool stuff and could care less about filming. Our loss. Thanks for the knowledge and entertainment.
If you only knew about all the super hot whammy stuff I'm working on........
All the best,
Tom
Quite a collection, very cool. V-block tour next 😁😁
Bout time we heard for you! Thanks Tom
The home shop has the most amazing residential fire suppression system eyes have been on.
Your 1 minute into for this video is PERFECT. I wish this were part of every excellent video you've shared. Please keep uploading videos as often as possible. Your content inspires others to create and share. Thanks you, Tom!
Oh boy, the press is on the work table...either the intro is old, or the project is back in the works.
First rule of Tom's workshop: don't talk about the etching press.
@@xenonram I refer to it as, "The project that shall not be named." It was the first thing I saw in the opening and was wondering if someone would post something. I bet it is gone in the next video. lol. I all honesty, Tom might just want to keep the project to himself. The hours, material, and passion that went into it and the fact it was for his wife.
Hey Tom , that was a truly GRIPPING video !😊
Thanks for advising us on your vise vice - all advice appreciated!!! Looking forward to #2. God bless.
A man of many vises.
cool, really cool! it's like having a tupperware show for aficionado of metal works. Thanks Tom!
your video perfect for my OCD, thanks
Intro felt like an AA meeting, or in this case, TA: “Hi Tom!” We addicts feel your pain.
I share your mania. My collection is a little more modest. Unfortunately, I don't understand English, but I watched the entire video. Thanks!
Thanks Tom - I appreciate your willingness to satisfy my tool addiction for the day.
Glad to see a new Oxtools video :)
I recognized the Fakes vise right away from the knob and general shape. I have a larger one (easily twice the size) that needs a restoration. Thanks for reminding me!
Just bough my first. A Gibralter in 3", MSRP 490$. I am a hobbyist so this is exciting for me: Seeing what and how you lay it all out. Thankyou.
i'll just go ahead and say it, Mr. Pete the "you-tube shop teacher", has you beat on vises. Might not have the quality, but he dern sure has quantity! Good video. You didn't show the little vise you made and did a series on. It was bad-assed!
Thank you for this. Your expansive knowledge and experience, is very helpful in explaining the differences that might not be apparent to most.
Can never have too many vises. I enjoyed your insight on these.
bcbloc02 Or indeed Too many Vices. ( Yeah, I’m probably fated to spend a bit of time in purgatory)....
Tom, that first vice is begging for a ring to act as the zero reference. With a small thumbscrew you could set the zero point anywhere around the circumference.
That's a great idea! Another project added to the list......
Cheers,
Tom
I can never understand why people downvote videos like this. Tom's stuff is amazing!! And while other people may not have the appreciation for this kind of content, why watch it if you don't like it.
There should be a rule that means you can *only* leave a negative feedback if you write a review/reason..
I have been told and I have no idea if its true, but i was told that the video showed up on someone's suggestion list and they aren't interested in these type videos. By clicking the thumb down RUclips wouldn't suggest his videos again. Even if that isn't the way it works there may be people that believe it does. Most likely the person who clicked thumbs down never watched the video.
@@buckinthetree1233 Hi, yeah that would explain it. However, there is an ignore / not interested option. Clicking the dislike isn't the correct method. Thanks for replying..
Thanks for the concern fellas. Its all good. It makes my day that I pissed somebody off and wasted their time.
All the best,
Tom
Good to see you back on RUclips Tom. Trust you and wife are safe and well
And I think the swiveling front of the Starrett vice keeps you maintaining the back datum of the vice. And, yes, maybe annoying in use but with a purpose...
Helpful video, many thanks Tom
Didn't you write a column for Cutting Tool Engineering Magazine?
If it was you, you gave some very and interesting tips . I enjoyed your column very much.
Loved it! For me, the quality of your videos is what makes them great.
I vote for best/most useful handtools. Thanks!
Daniel
Tom your videos are incredible. I pickup multiple things that are useful. The splash guard on the back of the grinder is number one priority for me (sick of fumbling with long sheet metal drop in guards that are usually always either to high or low)
Exactly what rang a bell for me!
I'm an inveterate background snooper and pick up on all sorts of tips like this.
A spring tensioned spray guard that doesn't worry the working head whatever it's height.
Stunning.
I'm thinking 2 widths for stacked setups....
Thanks, Tom. Great video.
Thanx for sharing this interesting important content 👍
Thanks for showing off your collection! I got a vice like the Herman Schmidt VO-4 you showed, mines 80mm width, I use it on the mill. And yes, hate the way the pin has to engage in the notch but I'm sorta used to it now. I got a smaller one with a through-pin rather than the ratchet thing, and I too found I can put the smaller vice in the larger vice at an angle.
Thanks Tom for another awesome, entertaining and informative video! ATB!
for the small vise, just consider, if you could get industry prices that large shipments of tool steel hover at, and you were making those small vises, you would be making them not one by one, but many at the same time... how many of those vises can you fit to grind parallel on your large s.g.? How many of them can then be transferred to the mill, gang setup, given the dovetails, especially on a horizontal setup, where you could gang mill rows of 10 of them at the same time by placing 5 cutters along the arbor, vises setup so the cutters are where they need to be... Its a large scale operation that produces no less than 20 vises at a time, hardens them, finishes all the surfaces on the grinder again and voila, shipment box ready... And consider that those are made like anything else on a cnc setup, which can operate with a jig setup to make hundreds of those every few hours, ready for h.t. and ``finish grinding to spec``... That in itself gives you a clue how they can make profit even at 40$ a pop... Hell, i bet i could supervise and direct an assembly line that could profit damn well from producing such vises... To the point that a power generation system would have to be made in house, to produce electricity for the production at lower prices than industry electricity costs with recent increases globally, just to kick the profit margin even higher... At factory scale, running a profitable production of these little vises is easy as fuck... Especially when its a multi facility factory that has every operation available in house, so the whole operation can be directed as a linear flow, or a cycle, if you have grinding to start and finish, with heating in between...
Tom, I loved your comments at the beginning of the video. Your reference to life long learning about the metalworking trade and your duty to share is admirable. Oh, and I enjoyed the vice porn too.
Regards, Mark from down under. 🇦🇺
Great mission statement Tom! Enjoyed very much as well as good to know. I always get hungry when I think of meatloaf! May the vise be with you!
The last vise you are displaying is the Starrett 160 ‘Toolmakers Steel Clamp’ and lists for $193.00 on Starrett.com. Thanks for making the video. Stay healthy.
Tom, it was so good to see you again !! I just wish we could meet up in person some day. I hope you and yours are doing well, with all of todays social road blocks. Your friend here in southwest Michigan, Cliff
Hey Cliff,
Great to see a comment from you brother. Hope you are keeping well.
Cheers,
Tom
man I have been worried about you,,, good to see you again,, thanks for the video..
Thanks. You are a man of many vices.
I've got a Shars "tool makers" vice, (no self respecting tool maker would use) and after some modifications to that annoying notch system nut works OK. The holes down the side allow me to reposition the jaw while bolted to the table. Works for holding parts at an angle in the mill vice or on the rotary table. Mr. Pete just made a hand vice video.
I really acknowledge and admire your metal working skills, as a boiler/maker welder my general tolerance range is shown on the drawings but +-1mil, no problem it’s my bread and butter my trade. After purchasing a lathe I expected to work to 1 tho max and within 10ths, I have learned not so easy, it’s a learning process, buying precision tools and a lathe does result in precision parts.
👍 enjoyed. Thanks Tom.
Hey Tom, if you need some small parallels take a regular set of 6" parallels and have a wire edm guy cut them in half. When I was a moldmaker apprentice I split the price of a set of parallels with another guy. To cut them our wire guy clamped them together and wire cut them in half, insta - grinding vice parallels!
I really loved your intro on this one.
To be honest, I love most everything you post.
Jig boring. Who remembers that? I still have some precision lengths and micrometers for a P&W machine around here somewhere. Great job, Tom.
Thanks. Didn’t know about the pin and spring in the little vices. Just upgraded my brown and sharpe vice.
Welcome back Tom!
Tom, the intro to this video was great. I hope you make it your channel introduction (or part of it). Loved the spirit of the message. Great content about vises too. I have one of those asian clones of the Herman Schimidt - it has a 100mm jaw width and I think the advertised opening is a bit larger again perhaps 125mm. It's a brilliantly made vise and very accurate, and grips well enough to mill with. I used it on my previous mill and will set it up soon with clamp bars for my vertical mill too. Thanks again, Craig
Gripping stuff! V blocks next, please.
One vote for V-blocks. Got a really good selection of v-blocks in the toolroom.
Cheers,
Tom
If? MSC was correct when I bought my 4" capacity Accupro grinding vise Tom I specifically asked where it was made before buying. U.S. made was the answer I got, but there's zero information anywhere on the vise nor was there on the packaging to confirm if that's in fact true. I've never handled a real Herman Schmidt so can't compare what they make to what I have, but at about 1/5th the price I suspect the HS products are still a large step above mine. However it still checks out well under the 2/10ths allowed deviation spec in every dimension and in some areas under a 10th. It really is the nicest and best made grinding vise I've personally used. Even the finish grinding is some of the best I've seen. It's one of the few tools I've bought where I think I might have paid too little. Where ever it was really made someone knew what they were doing when they ground it. Unfortunately I can't say the exact same brand or vise from MSC today is or isn't still as good. Afaik that Accupro name is one of MSC's house brands so anything with it might have been made anywhere.
Great stuff . Cheers .
I really appreciated your introduction! BTW: Can you do a video on hypoid gears? I've seen some pictures of them being cut and "some" of the setup. I know they're probably all made on CNC machines now, but they used to cut on milling machines with a dividing head, a shaft, and a gear on the feed. Thanks! Keep up the good work.
Is that a deeply embedded request for Tom to finish the etching press?
I used to watch offset hyoid gears being cut a lot (rings and opinions for rear ends). These were cut on Gleason's. One hell of a machine.
With the cost of grinding vises today that are perfectly adequate for most grinding work I have no idea why anybody would make one now.
As Stefan said, everything is made of rubber.
Remember the Suburban U-Grind-it kits.
There's a style of milling g machine vise that was being sold probably 20 years ago called a Quad CNC. The vise was different in that the fixed jaw was at the front towards the user. The fixed jaw was bolted to the vise base vertically and in the horizontal plane. Plus this jaw carried the activating screw. This type of vise would probably be well suited to being the basis for a grinding vise. Because the fixed jaw is carrying the thrust load from closing pressure I think it would have a lot less jaw flex than some other types.
Thanks Tom - I was selfishly hoping that we'd see more of you during the shutdown & worried a bit that the virus may have hit you or your family. Good to see you're well.
As for the video selection, I vote "D" All of the above - please :) Stay safe and well.
Thank's for your time love me some tools
I don't think that alot of people know what can be done with just a right angle plate a granite slab 12"x a hight gauge and a drill press .Yes and a hacksaw make it a starrett they cut nice and straight. I guess they call them bench tools. Great show Tom! Oh ya files lots of files!
cool vises, great lessons too...
Good thing for you that you got to Chuck's before I did, Tom...if I'd seen that Steve Edwards vise first I'd have it. Beautiful!!
That vise didn't even touchdown on anything of Chucks before I grabbed it. A great conclusion to the five year story. Steve is a cool cat ain't he?
All the best.
Tom
Thanks for the (ad)vise. :)
Love the video Tom! I would love to see your process on checking the squareness of that Schmidt vise. I have a Starrett and have noticed that it is out a couple but never thought about the tension aspect. I checked it static. Enjoy all of your videos!
I always eyeball the background of a video , so I appreciate facing a different direction today.
Very cool set of tools! Thanks for the review!
Dude Steve's vice is nice! I like tge layout, ratios, everything
Sweet collection of vises! Thanks for show them!.
Little Machine Shop does sell a set of 3" parallels but I figured that out after I made my own.
After I reworked my jig borer to become a bench top mill I invested A$140 on EBAY and bought one of those 100mm wide screwless vices...........I almost tore my hair out with the nut in the bottom constantly twisting around and dropping out ......only after I redesigned the angled screw down mechanism was it any good for milling.
Good content. Thank you. It would be interesting to see you recreate some of the weird stuff you get into at your day job. Not at work but in your shop. You did a tour one time and there was some really wild stuff going on.
Glad to see you back on the tube
Great video, I really enjoyed seeing these vises. You have some interesting pieces in your collection.
Great series, look forward to the next installment!
Am a long-time subscriber. Nice intro!
Live long and prosper Tom!!! 🖖🏻
This is going to be a great series; thanks for sharing!
I have a 1" precision vise that I made that works great for grinding flats on locating pins.
always great to see a vid from you
Thank You!
Those Starrett vises are handy little bugs. They seem to list on E**Y for more than the new price, for some reason, often with one jaw missing. I tend to use them (Starrett and the B&S version) in places where a toolmaker "parallel" clamp won't quite make it. They don't have the same hold in parallel cases, but when the angle is more than a few degrees, they are a lot easier to get full grip. Starrett calls them a clamp, not a vise, and I would guess my use is why. I also tend to pull them out when running CAD training. Lots of good geometry in these.
When you first showed that toy vise with the handle on it, my first thought was that it was some sort of violin maker's vise.
Great Video! Always quality watching, thanks Tom.
Wb Tom hope your keeping safe
Toms back.
Awesome tools, I love that dinky little vise..
28:30 another disadvantage of having a dangling knob/screw is that this "cantilever" brings undesirable eigenfrequencies and vibration-modes to an otherwise solide piece of metal. This could introduce chatter in a milling application, for example. I expect the (tightened) screw, as shown at 28:39, to vibrate somewhere between 50 Hz and 100 Hz.
Once that vise is tightened, it will never notice that screw sticking out.
This is going to be a nice video series.
I can see that first vise being used for making some sort of radii due to the lack of external angle adjustment on the top... maybe for grinding tool bits?
Thanks for the video Tom.
Just from the first 30 seconds I want to give 50 likes......!
You mention a stainless grinding vise. Are they magnetic? Thanks for sharing. Good seeing you on the Tube.
In case Tom doesn't answer, some stainlee steels are attracted to magnets.
Yes. They are typically 420 stainless steel.
cheers,
Tom
ETCHING PRESS SIGHTED!!
How do you only have 124k subscribers!!??
Great video, thanks Tom, enjoyed. Curious to how the bronze nut was secured in Steve’s vice, pinned somehow or just a press fit into the rear block?
A kilobuck! Another Ox Tools classic unit of measure.