Cody Do a burnout I built a k24 block k20 head Crx that i'm going to give to my dad on his birthday. He always loved the body of the CRX since it's light. I got one in awesome condition, Full interior stock and nothing broken or rattling .Going to throw on some ITB's and get it tuned.
Full Thottle He will gain HP and Torque with that turbo manifold because the collector is decent now, The one before the collectors were right aside eachother which is wrong.
I was watching some older videos and it sux how things change with fame. It was nice to see everyone enjoying working together and just doing the things they love. Seems like you're the only survivor through all this. I enjoy the videos and admire the things you have accomplished at such a young age. Keep up the great videos and I'll keep watching.
just a little tip kyle, try use a different grade of stainless (like 316) as 304 ends to crack over time due to the heat cycles/work hardening and weight of the turbo. Just something to keep in mind for future manifolds, loving the fab youre doing just want to impart some wisdom. keep up the good work
MR KYLE YOU ARE A GREAT MAN THAT REALLY WORKS HARD ON YOUR VIDEOS AND ON TOP OF THAT YOU GO TO SCHOOL 2!! SO YOU HAVE A GREAT VALUE OF RESPECT FROM YOUR VIEWERS..KEEP UP THE GOOD WORK IN THIS CHANNEL..I LOVE YOUR WORK AND THE WAY YOU CONNECT YOUR SELF WITH THE AUTOMOTIVE WORK.....
You’re 100% correct on that heat killing the stainless braided line. My oil feed line was around a MM away from the hot side of my turbo and burnt up from the inside out and had a nasty leak
I miss my Wago... But it saved my ass when i hit a cliff wall after swerving away from a moose. Also it was rusty as shit, and i still got the full 4wd setup (2 of them actually)
Far better youtuber than anyone i follow. Always get cracking with bits and bobs and not just vlogging utterbullshit. Never stop and dont take your useless so called friend to heart. Much respect mate. 👍👍👍👍
Damn Kyle, back at it again! Respect for finally clearing the air. Mad props on that turbo manifold. You should definitely tie it into the full exhaust.
NICE! You need to hit up miller or Lincoln and get them to send you welders. As popular as you are I would bet they would send some awesome units to show on your channel.
Of course you didn't get any sugaring, you didn't get a full penetration weld, notice how you can still see the gap when looking at the joint, that means you didn't get a full penetration weld.
Just Drifting I doubt he would have too much issue with it cracking in the short term but in the long run he'll definitely be re-welding a few of those joints
I would weld a tab on the side of the flange for the turbo on the collecter and then weld the other end to the exhaust flange that goes on the engine to help support the turbos weight
I subbed to channel cause of how calm he talks and explains well and of course awsome fabricator thats what i love about this channel it makes me feel like i can do what he does but then realize shit never mind i cant
Kyle i really hope to get as good as you with my TIG one day cause i'm quite novice now. Absolutely wonderful result looks tough and durable, good 304 Stainless too. Looks like i need a different cup for my torch also i noticed you have a Monster 14 do you think a size 12 would be better for the tight spots around the flanges and bends? i think it would help a lot if i got one like that with a mesh inside to help the flow of argon. Thanks for the guide also I'm getting ready for a turbo setup also and this is a good and close up tutorial nicest i've seen so far encompassing the whole mock up procedure and hardware nearly. Appreciate it man!
a few suggestions for welding, possibly less of a bevel OR do a fill pass, the weld look like they have sunk in a bit, nothing major for the wago imo, but for the next one , other than that beautiful
I was about to go to sleep thinking “damn what’s the chance I sleep through a new boostedboiz upload” then I looked at my phone ready to stay a bit longer
Them welds are on point Kyle, keep up the good work and shout out from Dallas Texas...Also got the complete K20A2, swap mounts and lots more coming this weekend for the MR2 Spyder. Can't wait to start putting it together #BoostedBoiSince2006 #BoostedKSeriesMR2sFTW
I would like to help ur channel, around the same time ur channel came around I was thinking of doing the same but just didn't have the motivation for it, so I just stuck to watching yours lol u keep it so simple it's the best. Great minds think alike.
What tig welder do you have? Please tell me it's a cheapo from like harbor frieght haha. I wanna learn to tig weld but dont wanna spend thousands to maybe never pick it up. Lol
There is a tig welder in the 700$ range you can do welds like this but the duty cycle is less, you can't get around spending the cash, good luck try Craig's list and try to find a good one used :)
Can you include details on where you bought the collector, flange,90s and how much they cost? That'd make the vid a little longer and more quality, in my opinion.
You are my favourite RUclips channel and have inspired me and my Dad to make project car, thank you
Don't forget to use air cleaner, your build will last 100 times longer than theirs :P
Cody Do a burnout I built a k24 block k20 head Crx that i'm going to give to my dad on his birthday. He always loved the body of the CRX since it's light. I got one in awesome condition, Full interior stock and nothing broken or rattling .Going to throw on some ITB's and get it tuned.
fuck yea dude I'm sure your pops will love it.
Same with me... not a fan of hondas myself... but brought an ek and on the process of fully forging it and turbo... just to see what it feels like 😂😂😂
I'm tired of the haters saying kyle is skinny. It's called weight reduction bro
Much respect for your work ethic and overall quality.That manifold is turning out nice.
Content is just getting better and better.
Yeah love the manifold build. Is it longer runners more hp or torque?? Where do you get your exhaust manifold brackets at. I want to redo mine thanks.
Isnt that just for intake?..
he should gain like extra 10-15 hp due to the better flow.
Full Thottle He will gain HP and Torque with that turbo manifold because the collector is decent now, The one before the collectors were right aside eachother which is wrong.
Your hoopty stable is impressive.
Some quick hooptys tho
Best comment. Kudos sir.
Brandon Blair best comment of the night
LOL Hoopty Stable, what about a Bucket Shack?
What a good way to start the morning lol
in my opinion the wagon is the perfect combo of race car and rice car
Awesome
I was watching some older videos and it sux how things change with fame. It was nice to see everyone enjoying working together and just doing the things they love. Seems like you're the only survivor through all this. I enjoy the videos and admire the things you have accomplished at such a young age. Keep up the great videos and I'll keep watching.
I love you’re videos! They always cheer me up when I’m having a bad day! Thank you for the positive you bring to my life!
This is the type of content that got me subbed. You're a hell of a fabricator. Damn good job sir.
The workmanship and patience put into that manifold is astonishing. And that's some nice tig action Dude👌
Kyle putting work in like always.. give credit where credit is due👏 👌 fuck the haters!!! 👊
Pretty solid welding
Swaz what kind is he doing ??
David Stevenson tig welds
David Stevenson GTAW
i was about to say his welding is orgasmic
looks like hes running it a bit hot tho
just a little tip kyle, try use a different grade of stainless (like 316) as 304 ends to crack over time due to the heat cycles/work hardening and weight of the turbo. Just something to keep in mind for future manifolds, loving the fab youre doing just want to impart some wisdom. keep up the good work
I love how you open the garage door and you have your MR2 and your ek and the go kart and then there's the odyssey haha.
You're a very talented guy Kyle, as I've said many times... best videos on RUclips keep it up man!
You have some tig'ing skills, Bro! Especially those collector ones
He bought the collector
Finally a wago video
And a cool one to!
M&R Tuning “baby this is what we came for”
Do you know what kinda wago it is ? Year wise
darkdeadpool gamings some ware around 89, thay made awd version to.
CaptainSnookumz bra I put a sentence you put a paragraph and your not to good yourself baby 😘
Not gonna lie you definitely have better quality than the other guys. Your work ethic is on another level.
MR KYLE YOU ARE A GREAT MAN THAT REALLY WORKS HARD ON YOUR VIDEOS AND ON TOP OF THAT YOU GO TO SCHOOL 2!! SO YOU HAVE A GREAT VALUE OF RESPECT FROM YOUR VIEWERS..KEEP UP THE GOOD WORK IN THIS CHANNEL..I LOVE YOUR WORK AND THE WAY YOU CONNECT YOUR SELF WITH THE AUTOMOTIVE WORK.....
You’re 100% correct on that heat killing the stainless braided line. My oil feed line was around a MM away from the hot side of my turbo and burnt up from the inside out and had a nasty leak
I miss my Wago... But it saved my ass when i hit a cliff wall after swerving away from a moose. Also it was rusty as shit, and i still got the full 4wd setup (2 of them actually)
love how many vids you've been making
That wago actually looks good!! I mean not sema show car good, but those wheels with that stance= fireee, not to mention the sleeper thise of things
Last time we saw a video on the wagon
Kyle wasn't even born yet
Kyle, your content is amazing. Keep up the great work man, I can't wait to see the MR2 make some major pow!
I need one of these for my wagon! Nice fab work, did good without back purging
Hands down the best video in a long time! Great work on this one Kyle!
Nice job with the welding, collector looks mint.
Far better youtuber than anyone i follow. Always get cracking with bits and bobs and not just vlogging utterbullshit. Never stop and dont take your useless so called friend to heart. Much respect mate. 👍👍👍👍
This channel is the reason I bought a civic and started making videos of my progress. Your one mad talented dude man, keep it up!
Damn Kyle, back at it again! Respect for finally clearing the air. Mad props on that turbo manifold. You should definitely tie it into the full exhaust.
Hell yeah what a way to start the week and morning.......keep up the good work Kyle
NICE! You need to hit up miller or Lincoln and get them to send you welders. As popular as you are I would bet they would send some awesome units to show on your channel.
That manifold actually looks good, You're going to make much more power. Keep up the good work.
Ayyee that Migos- Kelly Price at 5:05. Instant like
well done mate, glad to see your progress!
Who cares who's filming!? I'm just happy for Kyle and the quality videos he's been uploading
I love these sleepers👍😎👌
Great job Kyle! You thought it out and everything else will be easier to do now. Thanks!
Of course you didn't get any sugaring, you didn't get a full penetration weld, notice how you can still see the gap when looking at the joint, that means you didn't get a full penetration weld.
Daniel Napast yeah, it's gonna suck when the welds crack after a few passes
Just Drifting I doubt he would have too much issue with it cracking in the short term but in the long run he'll definitely be re-welding a few of those joints
Bruh, you work your ass off. I appreciate it.
One of the best tig welders I've seen on RUclips
Wish I had your motivation man! I've been staring at my half finished boosted B18 Integra in the garage. Not sure when it will ever get done
1:32 favorite song ever
This is the stuff I want to do... Need a tig in my life. Keep up the good work!
These are the kinds of videos that make your channel so great kyle, keep up the great work. I wanna see wago and the mr2 hit some 10's!!!
If your RUclips channel ever fails for whatever reason you'd be able to get a really good job super easy. That was some nice craftmanship.
Badass man!! Manifold looks good!! Love the wago! picked up an 88 rt4wd one myself few says ago! :)
7:02 them some nice welds
good work kyle. you have someone to hold the camera for you and it very quality is much better for that!! awesome!
so stoked you're working on this wago again.
It's lookin well done, juiced to see some wagon love.
Noob question. Since the engine moves, if he does a hard ass pull, won't either the turbo get fucked up or the radiator support dented to hell.
Only one way to find out ;-)
I would weld a tab on the side of the flange for the turbo on the collecter and then weld the other end to the exhaust flange that goes on the engine to help support the turbos weight
Pretty cool you can make your own manifolds
You are getting damn good with that welder. Looks dope!
I missed that thing!, looks awesome. Great job man!. It's a shame i can't get my hands on one of these fine civic wagons here in México.
Hey dude, super inspiring to see how far you and the Boyz have come!
These videos are inspiring , great work Kyle
I subbed to channel cause of how calm he talks and explains well and of course awsome fabricator thats what i love about this channel it makes me feel like i can do what he does but then realize shit never mind i cant
those freaking welds freakin awesome
You done a great job on that manifold . Looks awesome :)
Man those are some clean welds. Would you have Brent retune it? That new manifold hasssss to flow better than that cast one
These videos are why I subscribed to your channel. Build/weld more stuff!
Kyle i really hope to get as good as you with my TIG one day cause i'm quite novice now. Absolutely wonderful result looks tough and durable, good 304 Stainless too.
Looks like i need a different cup for my torch also i noticed you have a Monster 14 do you think a size 12 would be better for the tight spots around the flanges and bends? i think it would help a lot if i got one like that with a mesh inside to help the flow of argon. Thanks for the guide also I'm getting ready for a turbo setup also and this is a good and close up tutorial nicest i've seen so far encompassing the whole mock up procedure and hardware nearly. Appreciate it man!
The rims really set this wago. Btw proud of your welding skills look like they have improved over the time I've been watching
Can't wait to see the van boosted, gonna be so sick!
Nice work man. Glad to see Charlie is helping haha
a few suggestions for welding, possibly less of a bevel OR do a fill pass, the weld look like they have sunk in a bit, nothing major for the wago imo, but for the next one , other than that beautiful
great job. nice welds too. turned out great so far :)
I was about to go to sleep thinking “damn what’s the chance I sleep through a new boostedboiz upload” then I looked at my phone ready to stay a bit longer
Dude your welding is on point !!!!!
Hell yea! Tig welds lookn good bro👌😎
Hell yea Kyle, Your welds are Very good man, stack of dimes looks great ! Great content man !
Stuntin on that welder! Manifold looks sick.
Goes well, looks cool too, nice work
Good stuff bro welding skill came a long way keep it up my man. 🤘🏾
hate to hear that u guys split up but ur the one that does the most for the channel so fk um keep doing ya thing
I think after the dust is all settled between you and charlie; you,charlie, and hayden should do a reunion collab where you all meet at the dragstrip.
Them welds are on point Kyle, keep up the good work and shout out from Dallas Texas...Also got the complete K20A2, swap mounts and lots more coming this weekend for the MR2 Spyder. Can't wait to start putting it together
#BoostedBoiSince2006
#BoostedKSeriesMR2sFTW
I when you first started welding! You’ve came a long way
As usual Kyle fucking brilliant my man! Best wishes from Scotland bud.
I needed this. Wago content makes for a good Monday.
U make sick builds keep up the good work
I would like to help ur channel, around the same time ur channel came around I was thinking of doing the same but just didn't have the motivation for it, so I just stuck to watching yours lol u keep it so simple it's the best. Great minds think alike.
Back to almost daily uploads, love it!
Nice to see wago again. You should try to make the whole car look super clean
Damn wago looks sick👍
What tig welder do you have? Please tell me it's a cheapo from like harbor frieght haha. I wanna learn to tig weld but dont wanna spend thousands to maybe never pick it up. Lol
I think its a Miller, not cheap like HF lol
There is a tig welder in the 700$ range you can do welds like this but the duty cycle is less, you can't get around spending the cash, good luck try Craig's list and try to find a good one used :)
used craigslist is a good idea to get a quality welder for a similar price of the new generic ones.
The Diabolical boy genius, does it again!.. 🤘😎🤘
Awesome work kyle, is it me or was that Charlie in the video
Great to see the wago back!
Top notch video Kyle keep up the amazing work!
Can you include details on where you bought the collector, flange,90s and how much they cost? That'd make the vid a little longer and more quality, in my opinion.
man I can see a future business for you man, you can make BoostedBoiz turbo manifolds! it looks great! wish I could TIG weld
Keep them coming first mistake some RUclipsrs make is not posting keep it up bro
That's fucking good work bro. Props.
Your a really good welder bro you build so much way better than these bigger car channels
Very impressed with everything. Good job.
wake and bake to boostedboiz
crackhead savage facts sitting in my Civic doing the same love these vids
Wake and bake to BoostedBoiz IN MY WORKSHOP. Feelsgoodman
crackhead savage yeah budddy
Same here 😂👍
DUDE WEED LMAO