Put thick washer thick belt and rollers on my 23 and my buddys 16 today went smooth thanks for the videos definitely reduced the jerky starts, the hunterworks spring compressor worked great!
Thanks Todd, love the how to vids. Just got your belt for my 16 RZR can’t wait to put that on and get rid of the “jerky starts” now I see I need to update my clutch with the round rollers. Keep up the great work you doing and thanks for making QUALITY Products to replace the “half assed” stock parts!!
Just put the round rollers in my secondary clutch and put on your belt piece of cake thanks to the video. Keep up the great work and parts your providing love the videos
Unfortunately things change out of our control, the video is still applicable and the site says two only and we cut the price basically in half. The shows installing two, you get two at a lower price. But a good point.
Just ordered your rollers. I will install them when they arrive. What is the Dalton Kit used for ? I do not have the white washer. My unit only has 1200 miles and 170 hours. I have rather loud noise that appears to be coming from the clutches when deceleration down hill. When I give it gas it stops. Removed the clutches and there appears to be very little wear. Any ideas would greatly be appreciated. Love your videos. Thanks , Larry
If your parts are as well made as your video, I'm very impressed. I'm inclined to run out and buy a RZR just so that I can use your parts. Thanks! (Have a '17 Alterra XT 1000 and after market parts seem to be really rare for them.)
When you say never put them in the rear, what exactly do you mean? Looking forward to ordering this kit for my 19. Just hope significant damage isn’t done already. Only around 50 hours so hope for the best
@@ICU-th7qj yes it does, again send video or pics to my email todd@hunterworks.com the washer does not sit beneath the spring, it moves inside it on that shaft and rests against the spider nut and communicate via email or call me, I don't see this as easily
No, that most likely is just the rollers moving from once side to the other in the helix. My 17 Ranger does that. I run a Duraclutch system in it and it is gone
Round but not any that we sell, they have what we call the piece ofcrap clutch and they fail often. The Rangers with engine braking have the better ebs style clutch and our small rollers
James Stone For sure they won was the best day to do it and I bet you have where are you just not looking close when you take those perks out you’re going to see your groove and by the way I’m replying while driving so no telling what Siri said
Not sure to be honest, won't be long. In talks with Fedex now, there are some new rates with the new trade agreement. The other issue is shipping volume is so high that shippers are delaying delivery and losing items
![Yeat & Quavo - 5BRAZY [Official Music Video]](http://i.ytimg.com/vi/4XxnTAwyxus/mqdefault.jpg)
Put thick washer thick belt and rollers on my 23 and my buddys 16 today went smooth thanks for the videos definitely reduced the jerky starts, the hunterworks spring compressor worked great!
Sweet
Yes I put a set of the rollers in my Sportsman XP 1000 and I feel the difference it's a lot smoother up shifts and down shifts quicker.
Thanks Todd, love the how to vids. Just got your belt for my 16 RZR can’t wait to put that on and get rid of the “jerky starts” now I see I need to update my clutch with the round rollers. Keep up the great work you doing and thanks for making QUALITY Products to replace the “half assed” stock parts!!
Just put the round rollers in my secondary clutch and put on your belt piece of cake thanks to the video. Keep up the great work and parts your providing love the videos
Would be nice to update this video since you no longer give 4 rollers in the kit. I only received 2. Thanks.
Unfortunately things change out of our control, the video is still applicable and the site says two only and we cut the price basically in half. The shows installing two, you get two at a lower price. But a good point.
Hey Todd. Just installed mine today and so did the brother In law
Just ordered your rollers. I will install them when they arrive. What is the Dalton Kit used for ? I do not have the white washer. My unit only has 1200 miles and 170 hours. I have rather loud noise that appears to be coming from the clutches when deceleration down hill. When I give it gas it stops. Removed the clutches and there appears to be very little wear. Any ideas would greatly be appreciated. Love your videos. Thanks , Larry
email me this question and tell me the vehicle, miles and tire size when you do, todd@hunterworks.com
Thx for the quick response will be ordering soon!
Nicely done! Appreciate the effort!
Ooh and that’s why I hand start my bolts before putting a impact on anything
If your parts are as well made as your video, I'm very impressed. I'm inclined to run out and buy a RZR just so that I can use your parts. Thanks! (Have a '17 Alterra XT 1000 and after market parts seem to be really rare for them.)
They are made that well, over 100,000 rollers sold and only 15 failures and all were not caused by the rollers. I have no idea what that vehicle is
I will check your belts out!
When you say never put them in the rear, what exactly do you mean? Looking forward to ordering this kit for my 19. Just hope significant damage isn’t done already. Only around 50 hours so hope for the best
On the helix side, only used outside
Hunterworks Inc. thanks for the reply I will be ordering these soon
I assume this would apply to a General as well??Thx
Kyle Mitchem yes sir. Left off the list but think I mention it in video
I have a 2016 and the secondary looks NOTHING like what you're working on. 🤔
Then it is not factory, ALL non turbo polaris UTV's use this secondary from 16 and newer
I just ask u on a different video what pucks u suggest lol here I find out u sell them lol
Yes sir, first company to make them and still the best you can buy!!
Do I need the white washer that comes with the quite thick belt? My spring is 2 inch OD and the washer is 1.5 OD so the washer will not work
It has nothing to do with the spring, it goes inside it, watch install video and it must be installed
@@Hunterworks I Did that and it wont work
@@ICU-th7qj yes it does, again send video or pics to my email todd@hunterworks.com the washer does not sit beneath the spring, it moves inside it on that shaft and rests against the spider nut and communicate via email or call me, I don't see this as easily
@@Hunterworks I tried to call it went to tour voicemail
I also emailed you
Will this stop the metallic clunk when first accelerating on a 2019 General?
No, that most likely is just the rollers moving from once side to the other in the helix. My 17 Ranger does that. I run a Duraclutch system in it and it is gone
2019 ranger 900 XP’s have square pucks or round?
Round but not any that we sell, they have what we call the piece ofcrap clutch and they fail often. The Rangers with engine braking have the better ebs style clutch and our small rollers
Does the '19 rocks and trails edition have these?
Yes sir, all non turbo 16-19 models
Do i need the spring compressor tool to install the round rollers on my used secondary?
James Stone You don’t need it but it makes the job much easier you’re gonna need something to hold the spring pressure while you take the screws out
Oh ok i have almost 900 miles on mine don't see much wear from the square pucks. Would it still be worth changing to the round ones?
James Stone For sure they won was the best day to do it and I bet you have where are you just not looking close when you take those perks out you’re going to see your groove and by the way I’m replying while driving so no telling what Siri said
@@Hunterworks oh ok I will go ahead and order these soon thanks
Is there any problem like this on 2015 1k’s?
kinda, stock ones flat spot, ours do not. We have them for your model too
Does the clutchs need to be re aligned after I switch out the pucks and put it back on?
ICU81 2 no. This has nothing to do with that
@@Hunterworks so I can just throw the secondary back on there and bolt it down and it's good?
Idk 100% about these clutchs like you do
I mean does the secondary have to be aligned in any way with the primary after it is put back on sorry
@@ICU-th7qj no sir, we have videos for removing and putting back on too. But no alignment
I have that clutch puller and compressor if u wanted to do it
What are you saying or trying to offer?
What causes belt slap? What is the fix for it ?
What is the vehicle? But bad clutch calibration, these pucks in a worn clutch and or shaft spacing issues
Ordered mine
When are you shipping to Canada
Not sure to be honest, won't be long. In talks with Fedex now, there are some new rates with the new trade agreement. The other issue is shipping volume is so high that shippers are delaying delivery and losing items
We have a CA dealer, www.cutterloose.ca
@@Hunterworks Awesome purchased my items from them thanks
Either going on your reconmendations
"Not appropriate for social media" haha
Awesome. Thanks.
Roller for xp 1000 eps ?
Primary or secondary?
Thankyou
Clutch ...
What is your question? go to our site www.hunterworks.com all rollers are there