+Rohit S Iyer i try to put some tricks/hints in every video, since youtube is full of tutorials but most of the are muted or a sequence of steps, without taking in consideration what the viewer is watching
Thank you.I agree with your last statement because if you tamper with the design it will no longer be holding the features of its original design for which the designer has produced it for.
Hi there. Thanks for the good tutorial. I wanted to know if it's possible to taper on one side only (keeping the one side straight) and then mirror the whole part. Ciao!
Aren't you changing the wing profile by putting the thin feature on the outside. Unfortunately trying to put it on the inside results in an error message.
+Vignesh Thirumurthi check the values with excel. That happens usually on trailing edge when you close the spline. If you see something wrong erase useless zeros'
Mohamed Sherif you have to check the format of the coordinates. First, you should have 3 columns, x y and z (filled with zeros) second, check your sistem if use commas or dot when defining decimal numbers third, no space between commas and number, like 0, 467
quano chiudi la coda della NACA con il tangent arc, l'arco e' tangente solo alla linea superiore , ma non alla linea inferiore. chiedevo se ci fosse un altro modo per chiudere. Comunque ho rimediato chiudendo il codino direttamente da file excel, cosi' c'e' anche un bel punto unico alla fine!
+nicolas bisordi you have multiply the point coordintes by a factor which is your final dimension. If you want a chord of 400 , you have to multiply the coordinates by 400, 40 cm
Yeah when you replace commas with points, everything works. But when i replace them back, everything gets back to invalid. I also tried changing the cell format, didnt work as well. Its getting very frustrating XD. Anyways thx for the help 👍
Наука
Thank you, very thorough and thoughtfully planned!
this is what I need, you saved me a lot of effort, thank you very much!!!
you saved me a lot of effort, thank you very much!!!
Great tutorial! Really useful.
English was great man. Thanks for the guide.
Very good material. Thanks !
thanks, good guide.
Great video!!! am new to solidworks and your videos have been helpful so thank you!.
thank you for watching!
Thank you!! You helped me so much!
IT really helped, thx man!!
Thanks a lot. It's really helpful
you are good man, hi from brazil
Thank You for guiding!!!
Much needed for my project
The trailing edge closing was the gist!!.. Thanx!!
+Rohit S Iyer i try to put some tricks/hints in every video, since youtube is full of tutorials but most of the are muted or a sequence of steps, without taking in consideration what the viewer is watching
@@MightyWings thank you so much for the consideration
Nice work man thanks, Gracie
thank you very much. I solved the problem with your video. 5:25. was prolema with commas. good luck to you
+ErnstRm73 thanks for watching
Gracias por tu ayuda. Estoy en un proyecto donde tengo que disenar unas alas de avion, y usare tu video para ayudarme. Muchas gracias!
Your video was very helpful. thank you.
Thanks for watching
Grazie, molto utile!
Helped a lot thanks
Your english is clear....gracie...see you in guvano..
Thank you so much
Thank you.I agree with your last statement because if you tamper with the design it will no longer be holding the features of its original design for which the designer has produced it for.
Please can you tell me which book you referred in your videos?
Hi is it possible to create a hotwire cutting tool path using solidcam ?
What Are The "Units And Dimension Standard" Choosed By You While Started to Design this !
Hi there. Thanks for the good tutorial. I wanted to know if it's possible to taper on one side only (keeping the one side straight) and then mirror the whole part. Ciao!
Yes you can. In fact you can taper at 1/4 chord , 1/2 chord, chord on leading or trailing edge
how do I add two wing elements in one coordinates file?
Its a good trick but its not good hahaha thanks for the useful video it helped a lot :)
How to change the angle off attack?
If I have a two chord lengths and therefore want to build a tapered wing, how would I do it? Great Instructional video btw
Tapered wings can be located at , 1/4 chord leading edge, 1/2 chord, chord leading edge, chord trailing edge, 1/4 trailing edge
I need help. Whenever I open the dat file on the illinois website, I get the straight coordinates not that file.
+Science Man hi, you have to re-elaborate as in the video
what to do if i want to include the taper ratio for the airfoil
dafuq......how is the taper ratio related to airfoil
very intresting ,., maybe do you have the model from skywalker x8 , i need it for my tesis??? help me please
+Paul Yalama no i don't sorry an
Aren't you changing the wing profile by putting the thin feature on the outside. Unfortunately trying to put it on the inside results in an error message.
the change by putting thin feature outside is minimum if compare to inner thin feature. Outer feature is easier to handle
I am getting error that 3d spline is self intersecting.... I downloaded data from the same site as you told
+Vignesh Thirumurthi check the values with excel. That happens usually on trailing edge when you close the spline. If you see something wrong erase useless zeros'
Mighty Wings Thanks dude.
hello i am using solidworks 2016 i tried this method and solid gives me an error invalid contents of txt file ?!
Mohamed Sherif you have to check the format of the coordinates.
First, you should have 3 columns, x y and z (filled with zeros)
second, check your sistem if use commas or dot when defining decimal numbers
third, no space between commas and number, like 0, 467
Ciao, ho notato che solo la parte superiore dell'Arc e' tangente alla linea dell'ala, ci sarebbe modo di rimediare?
non ho capito ARC
quano chiudi la coda della NACA con il tangent arc, l'arco e' tangente solo alla linea superiore , ma non alla linea inferiore. chiedevo se ci fosse un altro modo per chiudere.
Comunque ho rimediato chiudendo il codino direttamente da file excel, cosi' c'e' anche un bel punto unico alla fine!
how can you you size the wing?, how do you change the dimensions?
+nicolas bisordi you have multiply the point coordintes by a factor which is your final dimension. If you want a chord of 400 , you have to multiply the coordinates by 400, 40 cm
thank you very much😁, never though you would actually respond, I really appreciate it
+nicolas bisordi i always answer any question, also by email....
My solidworks keeps freezing and crashing every time I hit convert entities.
may be a silly problem, but i cant seem to multiply the table in excel. I keep on getting invalid! plz helpp
Ahmad Esber try to replace commas with points. also you have to change the format of your cells from general to number
Yeah when you replace commas with points, everything works. But when i replace them back, everything gets back to invalid. I also tried changing the cell format, didnt work as well. Its getting very frustrating XD. Anyways thx for the help 👍
Ahmad Esber ok. try to change them with notepad. use excell only for multiplication then use notepad for replacing
Might work! Ill let you know. Thx