Can the inner tube be replaced when you remove the tire like this? Seems the wiring gives very little room to work. Do you have a video showing the replacement of the inner tube with the tire still attached to the wiring harness? Thank You
Follow the “how to strip stem” video for the top half of the stem. The bottom half is just swapping the controller out of the old stem and into new stem. It’s easy - you’ll figure it out. 😀
Is it possible to remove the side reflectors without damaging the sticky pads or do you have to get new reflectors each time? Where can I buy these reflectors?
Yes there are but we don’t recommend them as the quality of the ride is so poor. To prevent punctures keep your tyre pressure up - it needs to be checked weekly.
Soak it over night with WD-40 or similar. If it still doesn't move heat it up with a blow torch, let it cool then try. Also use a pipe over end of spanner to give extra torque.
is there a video out there explaining how to install a brand new one? I need to replace mine with a new tire and I'm not confident ill be able to know where the wiring goes and stuff.
my decent one (model one) scooters front tyre doesn't have a reflective strip. Its a thick hard plastic reflector. I have tried to pry it out but it feels like its going to shatter
As i said previously… its not a strip. Its a thick hard plastic reflector that seems to be glued into place. I had to break it off and when i did the two small holes seem to be done in the same manner
i have a question about my decent x7, im getting no power but the battery works fine as ive tried it in another x7 scooter, i was wondering if you had any idea what it could be? i was thinking maybe the power button on the throttle
My scoot was working perfectly fine until i got a nail in my back tire. So i fixed tge inner tube and when i went to take off, the accelarator doea nothing not sure what happened. But the front tire feels like its engaged like a clutch. So it does spin but hardly. The accelerator spring feels normal.what sgould i do
@@HorizonMicromobility ok thanks a million. Yea im not saying the fix roke it. I was just sayin that it was working 15 minutes prior then just stopped out of no where
I kmow im abit late, bit i followed this video exactly and when i put it all back together after changing the innertube, its coming up with e4 on the display and wont move, can somebody please help me 🙏
Okay thats the wheel with the wire right? Is it easy to take old one of replace with new one? Just looked at a quick video and looked pretty complicated 🙄
@@deadpoetztampa Yeah, that the only way of adding sealant, you can't add it with air in the tyre. Take valve core out, add sealant, put core back in pump up, scoot, If you have had a puncture then replace tube or mend puncture first. Check out our channel for video on how to add sealant for more info.
@@HorizonMicromobility don't know if it was punctured, replaced the back tire, today woke up the fkn front flat,smh so I gotta pull all this shit loose and see if it's punctured too,smh thankx
TurboAnt sucks for not having an electrical connector on that line, like all scooter makers who don't suck have. 😏 My cable doesn't have the slack that yours does, of course. The reason I am having to change the tire is because turboant does not inflate their tires and therefore does not test their inner tubes when they ship the scooter. so when I inflated my tire to 33 PSI it did not hold air because the inner tube was defective. so I am having to change the inner tube before I can even use the new scooter. Turboant offers nothing, when I called. Don't buy a turboant.
There is no customer service or warranty when you purchase many brands of scooter. We used to stock Turboant but whenever there was a warranty claim they would make things so difficult we gave up in the end. Always best to purchase from the country you live in as should be backed by warranty.
Thanks for this video, I was near prizing the plastic trim off until I saw this video about the rubber bungs with hidden screws 😮
Glad it helped
Appreciate the repair vids on the X7 Pro!
What size Allen wrench are you using to get the screws out of the covers??
Can the inner tube be replaced when you remove the tire like this? Seems the wiring gives very little room to work. Do you have a video showing the replacement of the inner tube with the tire still attached to the wiring harness? Thank You
Yes it can. Put the tube on from the opposite side to the cables. Or just disconnect it but that's more work.
Do you have a video showing the tube replacement with the tire like this? Thank you
@@frankadamski5857 check out the channel. You want one showing how to remove controller so you can disconnect cables.
nice tutorial..Any video on replacing the front stem?.mine broke on bottom part...
Follow the “how to strip stem” video for the top half of the stem. The bottom half is just swapping the controller out of the old stem and into new stem. It’s easy - you’ll figure it out. 😀
Very helpful. Thanks
Glad it was helpful!
Is it possible to remove the side reflectors without damaging the sticky pads or do you have to get new reflectors each time?
Where can I buy these reflectors?
Yes just peel them off with a knife and re-use 👍
Does anyone know if there are hard tires you can use on the turboant x7 pro? I’ve had my soft tires bust like 3 times
Yes there are but we don’t recommend them as the quality of the ride is so poor. To prevent punctures keep your tyre pressure up - it needs to be checked weekly.
I can’t remove the big bolt because it’s rusted any tips?
Soak it over night with WD-40 or similar. If it still doesn't move heat it up with a blow torch, let it cool then try. Also use a pipe over end of spanner to give extra torque.
What size is the Allen key that you use?
Most likely 17mm or smaller
For those looking for the answer - 3mm Allen key
Nice bike shops won't do this for a fee. Great tutorials needed to see thanks.
You’re welcome. 😀
is there a video out there explaining how to install a brand new one? I need to replace mine with a new tire and I'm not confident ill be able to know where the wiring goes and stuff.
It unplugs from the controller. Very easy, take photos as you go along if in sure 👍
@@HorizonMicromobility Thank you for replying👍
What about the back wheel, I have an X8 and the tyre popped so I want to replace it with a solid tyre, they're 10 inch
Please check channel as there is a video for that. But we don't suggest replacing with solid tyre as the ride quality is poor.
@@niteblaster1 Yup, you'll also get sore hands and wrist.... so don't do it.... cars don't have solid wheels for a reason 😀
my decent one (model one) scooters front tyre doesn't have a reflective strip. Its a thick hard plastic reflector. I have tried to pry it out but it feels like its going to shatter
The screws are under the reflective strip. It's just a bit of tape and will peal off.
As i said previously… its not a strip. Its a thick hard plastic reflector that seems to be glued into place. I had to break it off and when i did the two small holes seem to be done in the same manner
My small screw stripped after some time, anyway how to get some replacements?
Sorry not sure what size they are.
Head down to your local hardware store, if they don’t have the exact screw, they’ll at least have something similar (same size different finish)
One of the nuts on mine was tightened on so tight that the washer below it was deformed and now I can’t get it off. Any ideas?
Try spraying penetrating oil (WD-40) and leave overnight. If that fails try heating with blowtorch. Also use leverage on the spanner if possible.
i have a question about my decent x7, im getting no power but the battery works fine as ive tried it in another x7 scooter, i was wondering if you had any idea what it could be? i was thinking maybe the power button on the throttle
Controller is probably blown 😢
@@HorizonMicromobility no problem thank you is that an easy fix?
@@JaseGBT yes. 👍
How do I remove to the break line to access the tire free
Just remove the cable
Ty just got puncher and Dr orange did t fix it so gunna take a look ty again
Good luck, it’s fairly straight forward 👍
Do they think magnets grow on trees?
What?
@@HorizonMicromobility How can one change ballbearings in the engine.
@@andershoel78 No idea - sorry. Quicker and easier to replace the whole motor
@@HorizonMicromobility Those magnets are expensive.
My scoot was working perfectly fine until i got a nail in my back tire. So i fixed tge inner tube and when i went to take off, the accelarator doea nothing not sure what happened. But the front tire feels like its engaged like a clutch. So it does spin but hardly. The accelerator spring feels normal.what sgould i do
Not sure how fixing a puncture on back has caused an issue at the front? But it sounds like the motor is faulty
@@HorizonMicromobility ok thanks a million. Yea im not saying the fix roke it. I was just sayin that it was working 15 minutes prior then just stopped out of no where
Why has my scooter just said EC when ive taken my frunt wheel off
Put it back on. The controller indicates a motor error as it can’t detect the motor.
@@HorizonMicromobility that made no sense mate
@@connormarsden678 just mentioning that EC error is motor error
@@HorizonMicromobility yhyh my g
what size of solid tire you use??
We don’t use solid tyres. The ride quality is just not worth it.
I want the scooter much faster then 19mph what can I do
You’ll need something with a 500W motor rather than 350W
I tried this out did fine. Couple times but then inner tube troubles. Started happening and my scooter 🛴 won't power on anymore. Any tips suggestions?
If everything was working ok before you fix the puncture then there may be a loose connection somewhere.
@@HorizonMicromobility must be just haven't had the will to find disconnect.
Whats the screwdriver size?
Sorry don’t know, I never look at what size I’m using. If I pick up the wrong size I pick up another and try again. Give this technique a go. 😊
Thank you!
You’re welcome - happy scooting 😀
I kmow im abit late, bit i followed this video exactly and when i put it all back together after changing the innertube, its coming up with e4 on the display and wont move, can somebody please help me 🙏
That would indicate a motor hall sensor fault. you'd need to replace the motor as it's not practical to replace the hall sensors
Okay thats the wheel with the wire right? Is it easy to take old one of replace with new one? Just looked at a quick video and looked pretty complicated 🙄
@@adamdyson375 RUclips is your friend. Basically you just remove wheel, disconnect from controller and then replace with new
I stripped one of the wires. There is not enough slack in the wires. When getting wheel off.
@@annearly3200 Oh no! You should be able to solder it back. Disconnect from controller if you need more cable slack.
Why'd they make it suck so hard to inflate
It shouldn't be difficult to inflate. If you can't get the pump on easily carefully bend the valve out from the wheel.
@@HorizonMicromobility pain in the ass,can I put the puncture seal in while flat then inflate?
@@deadpoetztampa Yeah, that the only way of adding sealant, you can't add it with air in the tyre. Take valve core out, add sealant, put core back in pump up, scoot, If you have had a puncture then replace tube or mend puncture first. Check out our channel for video on how to add sealant for more info.
@@HorizonMicromobility don't know if it was punctured, replaced the back tire, today woke up the fkn front flat,smh so I gotta pull all this shit loose and see if it's punctured too,smh thankx
@@deadpoetztampa front and back?? That's tough... stop riding past that tack and nails factory!
Back tyre?
Front wheel removal
@@HorizonMicromobility ik I was asking if of how u do back tyre
@@heaney_s yup - there is another video on the channel for how to remove the back tyre
TurboAnt sucks for not having an electrical connector on that line, like all scooter makers who don't suck have. 😏 My cable doesn't have the slack that yours does, of course.
The reason I am having to change the tire is because turboant does not inflate their tires and therefore does not test their inner tubes when they ship the scooter. so when I inflated my tire to 33 PSI it did not hold air because the inner tube was defective. so I am having to change the inner tube before I can even use the new scooter. Turboant offers nothing, when I called. Don't buy a turboant.
There is no customer service or warranty when you purchase many brands of scooter. We used to stock Turboant but whenever there was a warranty claim they would make things so difficult we gave up in the end. Always best to purchase from the country you live in as should be backed by warranty.
for some reason the axle nuts just won’t come off
They can be tight. Try to create extra torque by using long handle on spanner/wrench, using old pipe etc
This worked great, the tire was a bitch to put back on. Tires that small always are a struggle lol
Long handle tire levers help
The screws dont move bro
Try heating with a blow torch or soaking with WD40 or adding a pole to spanner to increase leverage. They can be stiff.
Nice tattoo
🏃♂