Your turf is gorgeous!! I just bought an EGO mower from Ace Hardware and I’ve been watching YT videos all day because I didn’t know where the bag goes and that’s how I ran across your video. I don’t have nearly the lawn that you have, but your video provided some good information and a wonderful demonstration. Thank you so much!
Just a follow up. On your advice sir, purchased this model, and after doing two cuts to my modest .25 acre city lot, I am (a)in “mower Nirvana,” and (b) the envy of my neighborhood !🤣 But seriously, people on the block asking me about this “new electric deal” that I am running. All the usual comments (that I too use to have)…”I never thought those things were powerful enough”…”Man, I think I’m through with gas & oil too. Where’d you buy that ?!!” So thanks for your mower video series AND your personal response to me when I had questions on that odd mower series number. You ARE The Grand Guru of Mowers !
I went ahead and bought the blades from the link you posted above (EGO Select Cut Series High Lift Blade set @t ) and just got them in the mail today. So I immediately put them on to try and mowed for about 5 minutes. They definitely have more pull on the grass, no doubt. They suck up leaves no problem and I went over a few stragglers since my last mow this past weekend and they cut all of them. You can tell that they tax the motor a bit more but not enough to kick it into high gear just running with no load. I can tell that it will kick into high with less grass load now since the blade itself adds load. Which IMO is a good thing, talking about blade tip speed. I thought that before it took too much load for it to kick into high which hurt the cut quality (minimally as I think this mower cuts well out of the box with the aggressive blade). I tend to cut high using the 2nd to highest or highest setting. I have fescue in the south and if I don't cut high it will burn up. I noticed that on the old blades on the 3rd highest setting or lower it cut just fine with the old blade. It was when I went higher where you could really tell it would leave stragglers and parts of the grass uncut. That's where the cut quality suffered. This new blade definitely helps to cure that. Here's what I will say though. It's a big improvement but if you are expecting commercial honda type lift you need to temper your expectations. I've had mowers that will lift big twigs when set at 5 inches. This new blade will not do that, although it did pick up a very small twig with 3 or 4 leaves attached on the 2nd highest setting in my quick test. So if you're expecting a hoover then I'm sorry to say you might be disappointed. But if you are expecting adequate lift on higher height settings, which is what I really wanted and where the old blade was lacking, this is DEFINITELY worth the $40 you'll spend. I haven't mowed in tall grass yet so I can't really comment on the mulch ability however based on the above video I believe it will do just fine there given the results as well as the fact that we have the cross-cut blades. Thanks TME for the review and the link to buy the blades. Got them in under a week with free shipping!
I'm doing a conversion from my single blade ego to the dual blade. I was on the fence between getting the high lift or the mulching blade. I was originally going to get the mulching blade since I almost always mulch, but the high lift blade seems to be a better, more uniform cut, and does pretty good with mulching. I'm going with the high blade. Thanks for the content
Thanks again your time & videos, I like all your reviews because of your unbiased & honest approach, however I myself prefer to hear the products instead of music, it helps in decision making (and I hoping to see if yours has the same sounds over larger bumps as mine).
Great video. I have had my high lift cross cut blades for about a month now, and all I can say is wow. I find myself emptying my bag more now, than ever. The cut is clean, I'm quite satisfied.
Hi, thanks for your video. I may not have the same grass than you, I have very dense grass and the mulching dual blades does leaves mowhak lines. I believe that the grass is not enough lifted, the mower does not get enough air. Do you think those dual high lift blades will be better even if I mulch (they sell it for bagging). Thanks for your input!
Love the videos! Was just switching to high lift blade and watched how you replaced them. My issue is when I put the screwdriver in to stop the blade from spinning with my impact drill or hand wrench the white disc spins and nothing will come loose. Have you seen this!?
I had the first gen select cut last year. Decent mower but I didn’t care for the bagging on it. Got the XP model last month. Night and day difference. Love the XP mower. Great reviews.
@@seanrice7511 Toro is not very big here. I' have seen a gas Toro in a Bunnings store, but I've never seen them advertise and heard very little about them locally. I think the Toro name is already registered in other areas such as irrigation, which may hamper their introduction here.
Your time and effort is greatly appreciated 🍺 I wonder if both the connector nut & bolt set and center washer & bolt will be available for sale. Mine are looking a little beat up already after using my impact wrench a few times.
Using an impact driver I have found that I seldom have to secure the blade while loosening the bolt/nut. The impact action loosens them without rotating the blade.
Awesome.... ok I know that the battery of this mower can be use on the blower and the weed eater but how about the battery that comes with the blower and the weed eater? Can you use the weed eater battery and the blower battery on the mower? I ask because looks like this battery of the land mower is more power full or has more amps ! Please let me know. Thanks
Hi Angel yes 100% but keep in mind the more amp hours the longer your run time, 5ah will probably be a minimum but I say 7.5 is preferred. How big is your lawn?
@@philipmorgan1438 I think as long as your mowing an average weekly length and using a larger battery, you won’t notice much difference in run time from my experience. Mine did rev up more with the high lift blade. Fine by me.
Great video. I was wondering if you can tell me the nut sizes I'll need because in going to install the double blade system on my ego.. kinda hack... I heard you mention 9/16 or something. But I'm not sure what I'll need
@@TechMadeEzy thank you for getting back to me so fast. I just got off the phone with Ego and the woman told me I can use the twin blades for the select cut on my mower. I asked her twice just to make sure and she said yes. ?
@@TechMadeEzy sorry I didn't explain myself better. I don't have a select cut mower. I have a single blade mower.( LM2100SP) but she said I can put the 2 blades from the select cut on my mower. I think I will call Ego again and ask another representative to confirm. Goodluck with the channel.
Here is the direct EGO page for that series I promise you it’s not made to fit two blades Unless you try something unofficial egopowerplus.com/21-inch-self-propelled-mower/
I have been loving your videos. I am a complete lawn care novice (lived in co-ops up until now, so this is my first real house with a yard) and your videos have been a real help. Question -- which of the 3 blades is best for mulching up leaves (without bagging so they feed the lawn)?
I have not seen it sold separately for the select cut series I did include the link in the description below make sure you choose the right one if you're going to purchase it.
Just watched lots of mower reviews, most American but can’t understand why you guys don’t cut your grass much shorter so it looks more like a billiard table. Anyway I’ve just bought the EGO with the steel deck rather than the plastic deck but first impressions after only one use are great, never going back to petrol. Oh, looks like it came with the high lift single blade stock.
It takes a lot of work to maintain a lawn at golf course putting green length. You need a special mower to keep it short. You need to mow it 3 times a week. You been to water it often. Maybe that is doable on a lawn this small, but we are talking hours of daily work on a a yard with a bigger lawn. An some people do pay a yard service to do this … and who am I to complain if you want to spend $$$$ on keeping up with the neighbors. I’d rather invest mine. Just my two cents.
It would also be interesting to see this blade used with the side discharge shoot attached. That way you can re-cut the mulched grass and it gets dispersed more so there isn't so much of it sitting on top. At least that's how I think it would work out. Anyway, awesome vid and thank you. I've been waiting for this blade!
@@milanjurich1526 It's the HRR 216 Model with the GCV 160 Engine. Got it from Home Depot back in 2019 and it's already a dog - incredibly hard to start and the rear wheels continue to lock up all the time - after only 2 seasons of mowing. My EGO already destroys it!
Just buy the ego. U wont regret it. I own ego chainsaw,leaf blower,weedeater, self propelled lawn mower,the 2 stage snowblower and just purchased the ego zero turn z6. I love them all!!
Be careful using chrome-plated sockets with an impact. It can be dangerous. It probably won't happen with an impact driver like that, but I would still google why it's possibly an issue.
Very confusing when you say you cutting at 4. Just to make it clear, your cutting at setting 4 on the mower which is a HOC of 2.5 inches. Just refer to the height that your cutting at, it'll make it way less confusing , especially for some people who may not have an ego mower. Good videos otherwise , love my EGO mower.😎
I have watched practically every video on the ego lawn mowers. Why do the ego owners 🙄 🤔 lol have the worst looking lawns!! Omg is it just me or does the old saying not hold true any more. The grass on the other side of fence is no longer greener?
These battery mowers aren't yet ready in my opinion vs gas. They still cut like crap, look at all the mulch left behind. Not powerful enough to mulch grass blades.
![UNMATCHED POWER! EGO Select Cut XP 21" Self-Propelled Mower Review [10Ah 56V]](http://i.ytimg.com/vi/FMt6nuSUDy8/mqdefault.jpg)
Your turf is gorgeous!! I just bought an EGO mower from Ace Hardware and I’ve been watching YT videos all day because I didn’t know where the bag goes and that’s how I ran across your video. I don’t have nearly the lawn that you have, but your video provided some good information and a wonderful demonstration. Thank you so much!
Thanks Leslie and I wish I could say the lawn is always like that it's so much work I hope my videos help have a great day
Just a follow up. On your advice sir, purchased this model, and after doing two cuts to my modest .25 acre city lot, I am (a)in “mower Nirvana,” and (b) the envy of my neighborhood !🤣
But seriously, people on the block asking me about this “new electric deal” that I am running. All the usual comments (that I too use to have)…”I never thought those things were powerful enough”…”Man, I think I’m through with gas & oil too. Where’d you buy that ?!!”
So thanks for your mower video series AND your personal response to me when I had questions on that odd mower series number.
You ARE The Grand Guru of Mowers !
I went ahead and bought the blades from the link you posted above (EGO Select Cut Series High Lift Blade set @t ) and just got them in the mail today. So I immediately put them on to try and mowed for about 5 minutes. They definitely have more pull on the grass, no doubt. They suck up leaves no problem and I went over a few stragglers since my last mow this past weekend and they cut all of them. You can tell that they tax the motor a bit more but not enough to kick it into high gear just running with no load. I can tell that it will kick into high with less grass load now since the blade itself adds load. Which IMO is a good thing, talking about blade tip speed. I thought that before it took too much load for it to kick into high which hurt the cut quality (minimally as I think this mower cuts well out of the box with the aggressive blade). I tend to cut high using the 2nd to highest or highest setting. I have fescue in the south and if I don't cut high it will burn up. I noticed that on the old blades on the 3rd highest setting or lower it cut just fine with the old blade. It was when I went higher where you could really tell it would leave stragglers and parts of the grass uncut. That's where the cut quality suffered. This new blade definitely helps to cure that. Here's what I will say though. It's a big improvement but if you are expecting commercial honda type lift you need to temper your expectations. I've had mowers that will lift big twigs when set at 5 inches. This new blade will not do that, although it did pick up a very small twig with 3 or 4 leaves attached on the 2nd highest setting in my quick test. So if you're expecting a hoover then I'm sorry to say you might be disappointed. But if you are expecting adequate lift on higher height settings, which is what I really wanted and where the old blade was lacking, this is DEFINITELY worth the $40 you'll spend. I haven't mowed in tall grass yet so I can't really comment on the mulch ability however based on the above video I believe it will do just fine there given the results as well as the fact that we have the cross-cut blades. Thanks TME for the review and the link to buy the blades. Got them in under a week with free shipping!
Now that’s one nice impact driver! Thanks for the shout out my friend!! 😉💯👍🏼
AJ had to give you props
Did you hear that part 👍🏼
Great video as always ! Thanks.
But you cannot fool us, Howard Stern ! What are you doing, producing lawnmower videos?🤣
Great video! Love when you talked about your dog throwing up. Haha so relatable. Anyway, I'm looking forward to getting an EGO.
I'm doing a conversion from my single blade ego to the dual blade. I was on the fence between getting the high lift or the mulching blade. I was originally going to get the mulching blade since I almost always mulch, but the high lift blade seems to be a better, more uniform cut, and does pretty good with mulching. I'm going with the high blade. Thanks for the content
Very impressive. I may have to remove the mulching blade (I always bag) and install the high lift blade.
Thanks again your time & videos, I like all your reviews because of your unbiased & honest approach, however I myself prefer to hear the products instead of music, it helps in decision making (and I hoping to see if yours has the same sounds over larger bumps as mine).
Thanks KLF 👍🏻
Great video.
I have had my high lift cross cut blades for about a month now, and all I can say is wow. I find myself emptying my bag more now, than ever. The cut is clean, I'm quite satisfied.
Thanks Pooky yeah nice blade for sure
You are very thorough. Thanks guy.
Glad it was helpful! THANK YOU
Greetings from the southern most southern tip of Texas. My dog does exact same thing. Thinking of buying that mower. I just bought 650 ego blower
This is what I was waiting for! Great job with the test layout, I think I'm going to spring for the the high lift blade kit.
Nice to see Howard Stern work on his own mower!
Hi, thanks for your video. I may not have the same grass than you, I have very dense grass and the mulching dual blades does leaves mowhak lines. I believe that the grass is not enough lifted, the mower does not get enough air. Do you think those dual high lift blades will be better even if I mulch (they sell it for bagging). Thanks for your input!
Hi Armstrong thanks for watching Honestly no, they lift but the way they are designed they are made to bag with. My opinion
Yea it needs a high lift blade leaving a few stragglers when mulching. But the mower works great bought it for my daughter.
Love the videos! Was just switching to high lift blade and watched how you replaced them. My issue is when I put the screwdriver in to stop the blade from spinning with my impact drill or hand wrench the white disc spins and nothing will come loose. Have you seen this!?
Tha js Knux 👍🏻Can't say I have, check in with EGO see what they say, sorry couldn't help ya much here
I had the first gen select cut last year. Decent mower but I didn’t care for the bagging on it. Got the XP model last month. Night and day difference. Love the XP mower. Great reviews.
Great video, am going to use this blade on my next mow. Towards the end of the video l heard an evel sound , it sounded like a gas mower.
I wish you'd show tightening the bolts/nuts with a torque wrench to the proper torque values called out in the owner's manual. Otherwise, nice video.
I didn't even think of that. I should've read through the manual...off the top of your head do you recall the torque called for?
@@mikehamm1 Excellent! Thanks so much for the info..
Do u think the 2156 will do a better/nicer cut for regular grass than the 2135 model?
Ditto. Be careful using an impact gun for tightening . They are super powerful and it wouldn’t take much to cause damage
Happy with the mower just wish there was a way to cut a little shorter than 1.5”
I wish there was an official way to put like an EGO offical spacer that would lower the blade
In Australia, we don't get the extra blade, it just comes with the hi lift blade already installed.
I heard also the Ego brand is less expensive than the brands like Toro in Australia 🇦🇺. Funny how it all works 🌎
@@seanrice7511 Toro is not very big here. I' have seen a gas Toro in a Bunnings store, but I've never seen them advertise and heard very little about them locally. I think the Toro name is already registered in other areas such as irrigation, which may hamper their introduction here.
Be careful when you are replacing the blade nuts. There are torque specs that should be adhered to.
I just bought an EGO mower with all the blades. Best mower I’ve ever had in my 60+ years.
Thanks for sharing Erik stay with us I hope , Let me know how it goes
Are you getting a lot of mulch stuck in your mulch plug area? I have a ton plugged up in there when I pull the plug out.
@@TechMadeEzy it’s strange. I mowed very dry grass yesterday’s bad there was a huge pile stuck in my mulch plug around it and inside it.
Your time and effort is greatly appreciated 🍺
I wonder if both the connector nut & bolt set and center washer & bolt will be available for sale. Mine are looking a little beat up already after using my impact wrench a few times.
Thanks
Just want to mention to remove the battery any time you tip the mower over.
Using an impact driver I have found that I seldom have to secure the blade while loosening the bolt/nut. The impact action loosens them without rotating the blade.
Awesome.... ok I know that the battery of this mower can be use on the blower and the weed eater but how about the battery that comes with the blower and the weed eater? Can you use the weed eater battery and the blower battery on the mower? I ask because looks like this battery of the land mower is more power full or has more amps ! Please let me know. Thanks
Hi Angel yes 100% but keep in mind the more amp hours the longer your run time, 5ah will probably be a minimum but I say 7.5 is preferred. How big is your lawn?
Sure stay in touch let me know how it goes
Does your rear tire lock up sometimes depending on the turns and reverse you do?
This happens on 3 of the 3 egos I have owned.
Mine does too. When it does that just push the the mower slightly forward then it will unlock
Do you all think this is a design flaw and should be addressed?
Do you think adding the high lift blade will reduce battery life when mowing?
@@TechMadeEzy I can live with that...
@@philipmorgan1438 I think as long as your mowing an average weekly length and using a larger battery, you won’t notice much difference in run time from my experience. Mine did rev up more with the high lift blade. Fine by me.
@@seanrice7511 If it doesn’t half
the mowing duration or like, it wouldn’t matter much. 👍
Looks like I should buy a lift blade for my older version self-propelled EGo mower for which it wasn’t offered 3 years ago. 👍
My pleasure stay in touch let me know what you end up doing and if you need any help
Great video. I was wondering if you can tell me the nut sizes I'll need because in going to install the double blade system on my ego.. kinda hack... I heard you mention 9/16 or something. But I'm not sure what I'll need
I’ve never done that before but it was 9/16 and 11/16 and thanks for your comment 👍🏼
I don't know about the hack so I won't be able to help you, also be careful you could void your warranty.
I use my impact wrench to take the bolt off Milwaukee 3/8 impact wrench
Great job. I have a LM2100SP would you know if I can use the 2 blade system high lift for the select cut?
@@TechMadeEzy thank you for getting back to me so fast. I just got off the phone with Ego and the woman told me I can use the twin blades for the select cut on my mower. I asked her twice just to make sure and she said yes. ?
Yes select cut mowers come with twin blades already, then you can change blade types like high lift etc.
@@TechMadeEzy sorry I didn't explain myself better. I don't have a select cut mower. I have a single blade mower.( LM2100SP) but she said I can put the 2 blades from the select cut on my mower. I think I will call Ego again and ask another representative to confirm. Goodluck with the channel.
Here is the direct EGO page for that series I promise you it’s not made to fit two blades
Unless you try something unofficial
egopowerplus.com/21-inch-self-propelled-mower/
I have been loving your videos. I am a complete lawn care novice (lived in co-ops up until now, so this is my first real house with a yard) and your videos have been a real help. Question -- which of the 3 blades is best for mulching up leaves (without bagging so they feed the lawn)?
I only need a high lift blade not a set.... Is it possible to purchase it that way?
I have not seen it sold separately for the select cut series I did include the link in the description below make sure you choose the right one if you're going to purchase it.
I am thinking what you called a gator blade is the mulching blade
Looks like it did a fantastic job! When you were using the high lift blade sucking up the grass did it rev up? Or just stay in low power mode?
Should have compared the mulching blade to the high lift blade when mulching.
Just watched lots of mower reviews, most American but can’t understand why you guys don’t cut your grass much shorter so it looks more like a billiard table. Anyway I’ve just bought the EGO with the steel deck rather than the plastic deck but first impressions after only one use are great, never going back to petrol.
Oh, looks like it came with the high lift single blade stock.
It takes a lot of work to maintain a lawn at golf course putting green length. You need a special mower to keep it short. You need to mow it 3 times a week. You been to water it often.
Maybe that is doable on a lawn this small, but we are talking hours of daily work on a a yard with a bigger lawn. An some people do pay a yard service to do this … and who am I to complain if you want to spend $$$$ on keeping up with the neighbors. I’d rather invest mine.
Just my two cents.
Thanks Thomas yes we do all have different circumstances for sure
How much of the grass blade would you say you cut during this video?
It would also be interesting to see this blade used with the side discharge shoot attached. That way you can re-cut the mulched grass and it gets dispersed more so there isn't so much of it sitting on top. At least that's how I think it would work out. Anyway, awesome vid and thank you. I've been waiting for this blade!
Hi thanks for watching, I don’t understand your question , please ask in another way. Thanks
I tried that rear side discharge just for the heck of it and still pretty messy, rear discharge isn’t worth it for me
Thx
Thank you
I love my EGO LM 2156SP! Bye Bye Honda...
Which Honda did you have … HRX?
@@milanjurich1526 It's the HRR 216 Model with the GCV 160 Engine. Got it from Home Depot back in 2019 and it's already a dog - incredibly hard to start and the rear wheels continue to lock up all the time - after only 2 seasons of mowing. My EGO already destroys it!
@@DeadSeaGenesis Nice to hear. I’m looking at the EGO and the Toro battery right now.
@@milanjurich1526 You can't go wrong with the EGO 2156 SP. What an amazing mower! It brings me back to my Lawn Boy days only BETTER!!!
Just buy the ego. U wont regret it. I own ego chainsaw,leaf blower,weedeater, self propelled lawn mower,the 2 stage snowblower and just purchased the ego zero turn z6. I love them all!!
whats the use of ego products when they are never available..always out of stock not know when they will be in ?? want edger too . i am in Canada
Supply chain disruptions due to the pandemic. Keep an eye out at Rona.ca, Lowes.ca and igocordless.ca
Be careful using chrome-plated sockets with an impact. It can be dangerous. It probably won't happen with an impact driver like that, but I would still google why it's possibly an issue.
COMPLETLY USELESS. Using a high lift bagging blade to mulch is FOOLISH.
Ridicules suction test.
Very confusing when you say you cutting at 4. Just to make it clear, your cutting at setting 4 on the mower which is a HOC of 2.5 inches. Just refer to the height that your cutting at, it'll make it way less confusing , especially for some people who may not have an ego mower. Good videos otherwise , love my EGO mower.😎
Good advice thank you for watching and thank you for your comment
If you want powerful cordless tools go with Milwaukee
I have watched practically every video on the ego lawn mowers. Why do the ego owners 🙄 🤔 lol have the worst looking lawns!! Omg is it just me or does the old saying not hold true any more. The grass on the other side of fence is no longer greener?
These battery mowers aren't yet ready in my opinion vs gas. They still cut like crap, look at all the mulch left behind. Not powerful enough to mulch grass blades.
Impact driver! Not drill!
lol yes sir
Thx