As an registered electrician with 20 years experience - nice job 👍 I would have charged £150 parts and labor plus certificate for that. ( in august 2021 ) To water proof further I would have run silicon around the whole socket where it is in contact with the wall except the bottom side.
Well thank you very much for the comments - especially coming from a registered electrician - much appreciated! What I didn't show in the video was 2 days later I had a look at the socket and did exactly what you suggested and ran silicon around the top and 2 sides of the box just to give it some more protection!!!
@@Phillwin It is legal to do it as a homeowner and ironically because it goes though a 13amp plug is safer as you have an additional fuse along the way. You do need to make sure that you have a RCD somewhere along the route though.
I lost my dad when I was 13, he was always DIY proficient and could fix anything, watching your videos helps me learn cope and learn the skills he always tried to teach me. If you see this I want to say Thank You, for helping fill a void and for being a positive role model.
I am sorry the hear that as it was my Dad that taught me the basics and the reason I've ended up doing what I'm doing, so I totally understand. Thank you for your kind comments and be assured that by watching these type of videos (not just mine) and practicing (and making lots mistakes like I have) you can become extremely proficient, which I'm sure would make your Dad very proud.
Was going to say something similar! aha. I've also not finished watching, but drilling from either side and meeting in the middle is a skill in its own right!
@@ProperDIY Very good instructional video, I was more concerned about how did you know there were no fixtures in both walls before you made the holes!!!! I would like to know how did you install that tap on the outside and linking it from the inside. I have just subscribed.
An underrated part of your videos is good production. I don't mean fancy edits and effects but clear audio and camerawork. Contents is excellent and succinct as usual. Thank you.
Great comment about using the hammer to keep the clips equal distance! It's the little things that most people won't notice (like the equal spacing of the clips, like the silicone in the conduit) that makes all the difference to the end result. Only just found the channel so working through the videos, love what I've seen so far! Keep it up!!
Great video and love the idea of a plug inside the house. One tip when drilling holes in external walls, I always drill at a slight gradient keeping the drill slightly lower than the drill bit point. This way, if any water does ever get to the hole and the silicone has failed, the water would run down to the outside and not inside. I would also run a bead of silicone along the top of the external plug unit to be absolutely sure.
Thank you. Good tip - I did think I might try that but was so worried the 2 holes would not line up from either side I thought I would be pushing my luck to them try to incline them as well. I was looking at the socket yesterday and though I might seal around the top and sides as you say - thanks.
@@ProperDIY I'm just wondering if you use (as you seem to have done) a small dril from each side first and then use a larger drill on the outside at an angle (downwards)(and sloping up on the inside) when enlarging the hole for the pvc pipe - you might only need 2-4 degrees...
You not only produce fantastic DIY advice and techniques but your videos are a work of precision too, from filming to your detailed advice and instruction......love the channel.
Superb, I am on my own and wanted an outdoor socket for the lawnmower. I have put my socket under the porch area so it is protected from rain etc. but have followed the video and done mine to a plug as well. Wasn't sure that was correct but your video confirmed it was all ok. I did however use electric cable that was suitable for outdoor use. although a bit more difficult to work with. Many thanks.
I do a fair bit of DIY around the house, and I have been agonising on how to wire a socket like this, for ages. I am not a competent electrician, and so I was delaying the installation as I didn’t want to pay an electrician a lot of money! Having come across your video, just by chance, and watching it, has given me a lot of confidence. Your way of describing everything in detail, yet without jargon or confusing words is commendable to the highest. Thank you very much. Now, I’m off to B&Q!
Well, after looking at so many videos on this subject, I decided that your 13amp plug solution was the one to go for. I think it was the only one with that idea!!. I followed your instructions and found it all worked out well, with one modification, I put the cable in some trunking. Ohh what a game that was!!! But I liked the look as it was in the Living Room. The conduit through the wall was an interesting time, getting to stay in place when sealing it. It kept on moving. Recommend, longer is better than shorter!. Thanks so much for giving me the confidence to do this job
I’m an electrician myself and I like this idea and a very neat installation. Couple of tips When using stranded flex cable I always use ferrule crimps to prevent damaging the stranded cores when terminating. Also make sure the socket you plug into is RCD protected inside the house 👍.
I've just watched this prior to installing exactly what is demonstrated, and I thank you for the wonderfully easy-to-follow, no nonsense instruction. That was well worth watching. 👍🏻
Thank you Stuart for taking the time to make the video that has now given me the confidence to install a outdoor socket and saved me paying an Electrition to do it for me, made my day.
Tbh, I found it just as easy to turn off the mains, remove a socket on an outside wall and drill through, wiring the new socket into the interior socket. It's still a very simple task and is neater.
I have two of these boxes to fit. Thanks for the clear instructions. I had a friend drill through the cavity wall for me took a couple of minutes for both boxes. If he hadn't done it I would have bought the drill bit. It would have save alot of stress and time trying to line them up. So many excellent tips. Cheers 👍🏼
Hi Stuart, thoroughly enjoying all of your videos, great content and production. As a former electrician and electrical installation lecturer I agree that this is an excellent option for an experienced DIYer. This method removes the need to safely isolate, test and certify wiring attached to the existing circuit. As you mentioned this is an RCD protected extension lead so a great option for outdoor power. I used to teach the folding over method and the reason is that most terminals on electrical accessories are designed for two cables, so folding a single cable helps to fill the terminal and provide a more secure connection. Keep up the good work!
John, that is very much appreciated coming from an electrician - I tend to get a lot of grief from electricians who do't want to see anyone unqualified even fit a plug. Now I know why the cables are folded - learn something new every day!
@@ProperDIY Hi Stuart, I agree completely that in some circumstances a qualified tradesperson is the best option, but DIYers will have a go. I think you've illustrated a safe method of achieving an identical result to anything an electrician could produce. Do you mind me asking of you've done any formal teaching?
@@ProperDIY A natural then! Your videos are very clear and well produced, (I've currently got a large piece of plywood and several lengths of 2X4 in my garage ready to follow your workbench tutorial!) Looking forward to your next video.
What a nice job! Just completed a similar job, using these instructions, and I have to say - it went about as good as I could have wished for. Kudos to Proper DIY for an outstanding, easy to understand, and thorough approach to the project. Let's start out with the elephant in the room: Getting an electrician in, tapping into a ring circuit, doing all the tests, and issuing a certificate of compliance is going to cost several hundred pounds. As it should, given the cost of testing equipment, skills of the electrician, etc. This approach sidesteps most of the costs, while maintaining the safety inherent in the UK electrical code.
Little tip I do with any plug is make the live wire shorter than the neutral and the earth longest, that way if the cable ever gets pulled the live wire is the first to get ripped out
Yes that was one of the first things taught in college (80s) lecture gave us all a plug top and said wire your plug, only two of us got it correct, always have the live wire taught and a big curl in the earth, doesn’t matter if the live comes out means the appliance won’t work but the earth should never come out first. Great video.
The ‘RUclips algorithm’ suggested your garage door video. I was impressed by your presentation, so watched some more of your videos. I may copy your workbench. Your channel deserves to grow 😀 As an industrial maintenance electrician I can confirm that this is the best method for a DIYer to fit an external socket, and for me too as there is no need to be part P registered as existing circuits are not altered. You have shown how to safely install a fixed, waterproof extension lead. I would echo the comments regarding using ferrules to keep the copper strands secure in the socket terminals, but your twisting then folding of the copper wires is the next best solution. Nearly all connection issues I encounter are caused by the screw becoming slack against the copper wire over time, by filling the terminal with more copper wire the strands are less able to move as the screw is tightened ensuring that when tightened the connection will remain tight.
Thanks!. Good, sensible comments which I agree with. I'll have to look into the ferrule addition - I've never used them. Great to get feedback from a calm, logical electrician.
Very clear, in plain English and the gentleman speaks slowly so that everyone understands. He makes any hard job looks simple, well done. I'll be copying excatly what you did when installing mine. Keep up the good work, waiting for more useful DIY vedios. Thanks
I've been thinking of getting a sparky in for this as I didn't fancy messing about with electrics but your way is really easy for a competent DIY person such as myself. Thanks for such a great informative video :)
Yes Im positive, as long as this is terminated correctly and RCD protected it's perfectly safe imo and would do it in my own home. Probably wouldn't if I could back to back it off a socket but it has its place,cheers
I believe that is essential . Water trickles down the inner face of the outer bricks or blocks within the cavity. If the duct is horizontal or sloping back into the house the water will pass to the inner leaf of the cavity wall and potentially cause dampness.
@@chapman9230 It has mastic on it so not necessary at all. The cavity (depending on year) should have trickle vents to let out water/condensation which builds up.
I think I might do this myself. I've had enough of dragging an extension lead and hose on a reel from the exterior socket and tap in the back garden whenever we wash the car. The only sensible option for power is the sockets under the front room window. That'll work. No trailing cables and no trailing hose as I've fixed it to the side of the house and all we need is a short length to attach when washing.😊 Follow up: installed as I said I would but also added an alexa based wifi plug to operate it. Added a LED driveway light on the first floor powered in the same way. Both voice activated, bloody clever stuff! I've even turned the light on from a different country!😂
Another great clear concise video! I've recenty taken to crimping ferrules into the end of copper flex after exposing the copper. Looks neat and stops them getting messy if you need to readjust things 👍
Yes, I bought a ferrule crimper for flex connections. Only other thing I would have done was to put a cable tie around the flex exiting the inside box, just to stop it getting pulled if something gets caught on it.
I've just done this after watching your video. Decided to run the cable round the back of the fridge freezer. After moving the fridge for access all going well but then noticed the freezer door screws were really loose and door hanging off. The screws holding it on were not doing anything and had no bite left, no wonder it had been leaking. so then spent the next few hours taking fridge freezer doors off to fix it all. So now got a double socket right next to shed and a fixed freezer :)
Just done two of these today and I’m pretty useless at most stuff, but they turned out fantastically. Thanks for this video. I had to get myself 40cm drill bits, but for £8 (for 8, 10, 12mm) it’s a no brainer). 👍
Hats off to you for producing a video that is easy to understand and follow. Your instructions are clear and concise and I particularly like the fact that you explain why you are doing something a certain way. subscribed. You have given me the confidence boost to actually do the work myself PS Why hadn't I ever thought about using my hammer to space out clips ? I certainly will from now on. I am off to buy my outdoor switch - wish me luck.
Hi there, I just want to say I absolutely love your videos. Unfortunately I did have a dad who didn’t really teach me much and wasn’t really a part of my life. But I just wanted to say that I absolutely appreciate all the hard work you do. Thanks to you. I have installed new sockets in my stepdaughters office managed to put electrics outside the House and many more things that you talk people through. I suppose growing up, not being taught anything, it just looks all scary But when you put your mind to it and follow the basic steps how you put your content out it’s not that scary. I suppose it’s like riding a bike once you keep doing it you get better it every day but I just really want to thank you and appreciate your service. Like everybody else this has saved me hundreds of pounds getting chippy, Plumber, And Sparky, in I think you’ve mentioned it before. Did you say you had a membership page? As you clearly have saved me a hell of a lot of money. Dave
Great content. I needed an outdoor socket for my daughters rechargeable sit on car and my hot tub. I followed this process and it solved the problem I had. Great advice and I'm chuffed with my new outdoor socket. I also like the fact that I can isolate the power to the garden from the house. Took me a couple of hours to get everything done but works really well. Thank you 🙂
Stuart many thanks for this video I have successfully installed my outdoor socket. Neighbours all want one now I stated watch Stuart and you can do it but most want me to do it, lol. Thanks again
Really excellent content, thorough and to the point. Everything you do is done well and thought out, which means the job can’t fail. I can’t tell you how much difference it makes to see someone doing this. You are passing on great skills. Thank you.
Well thank you very much for your comments. I always think out projects before they start and especially if I'm on camera. Anyone spending 10mins+ whatching me should, I think, deserve to leave with at least with good tip or a laugh or 2.
@@ProperDIY yes and what strikes me is that many jobs, like this one, are actually a series of smaller jobs, each perhaps requiring a basic skill. Your video didn’t assume that I knew how to do anything, no missed steps, but at same time you managed to keep it from being long winded and patronising.
@@michaeltester5187 Thank you again. It's actually a difficult balance to show everything, be entertaining, miss nothing and not make videos 50 mins long!!! I'm always concerned that I will fail on one of those.
Haven't done a socket in sometime...it was a great reminder how do it again..and I agree with putting a plug on ,as opposed to wiring directly...for all the same reasons you outlined...a very helpful video..cheers pal..
Great video, you present them really well. Any chance of making a video on fitting wall plugs and what size to use, and drill size needed for each plug? I'd find that useful, thanks.
Thanks for your help on fitting the outside socket. I purchased the same product from Screwfix + 16 mm drill bit to go through wall + plumbers pipe all same day. All working fine and making such a difference instead of running x lead from house. 👏👍😉
At last! New viewer and I have subscribed as you do d-I-y at my level (trimming the cable!) lots of channels say for a amateurs but then do stuff I will never do! And with you use UK t&c’s. I just paid for a spark to fit an outside 13amp supply “because it had to be terminated to the mains” , I never considered a simple plug top…….I could have done all this very happily. You, my man, you could save me cash whilst educating me! Bob England
Very impressed and I totally agree its the safest DIY method and also with the added bonuses you mentioned . One tip if using a set of pliers to strip back the insulation on the cables, is to do exactly what you did with the knife and score round first (basically griping the cable in the cutting edge and turning the pliers clockwise and back a couple of times ; this prevents both you gripping too tight and cutting it off completely and also helps prevent pulling the odd strand off too .. (apologies if this is mentioned below - 884 comments at the time of writing) 30+ years ago when doing my apprenticeship, we were always told to use strippers (cable ones!!!!) but, after a bit of practice you know just how tight to grip and it saves a bit of time as you can strip, cut and bend all in one go (so to speak! 🤔)
The only down side of this is that you take away one of your internal sockets availabilty. Rather wire as a spur or better still as part of the ring main, but it would then require sign off
Another top tip filled vid, i see your point with the cable clips i normally put a well positioned 6 inch nail straight through the cable every 6 inches to make sure the cable is firm to the wall and have no concerns over safety as when its all plugged in i normally get the neighbors kids to stand in a bucket of water and lick the cable and switch so far no issues, keep the vids coming as they are very helpful. P,S top tip about the remote switch for the power i will wire in the mother inlaws chair and see if it lights her up from a safe distance taking into account health and safety guide lines
This couldn't have arrived in my feed at a better time, trying to find an electrician to put in an extra plug into our new to us home is a nightmare, having this idea means I can do it myself and save a couple of hundred dollars and still be safe! Many thanks and hi from New Zealand.
Watching your video I have installed socket outside it’s save me lots money and time thank you very much I really appreciate your you’re videos very helpful very simple thanks again
Thanks!! Great to hear some down to earth advice without all the clap-trap we hear from some presenters. P.DIY is always my first port of call when I embark on a project. I always learn something.
As a DIYer I'm very happy I found your channel I have all ready subscribed.i have checked out a good few of your videos and they are all very informative and helpful and plenty of safety tips too
Good stuff. I like to pin the conductors if they are stranded and the connection is screw type as opposed to clamp, just for good measure. I've seen stranded conductors get damaged over time where the screw presses into it and make imperfect contact. Probably why the newer method insist on doubling down the exposed wire.
congratulations - You are the first keyboard electrician., I know you just couldn't help yaself so please collect your pedant award. Everyone knows how cable glands are totally impenetrable to water and silicon is basically a water sponge and magnet all in one!, what was he thinking!!!!
@@mattsan70 wow what a comment. Not a keyboard electrician at all. In the video he says he paid for an IP rated fitting and doesn’t want to drill a hole as it will lose that rating, all I’m saying is he’s lost that rating already so should drill a hole. Didn’t slag off the work, but clearly you’ve taken offence, so here is your award for being a snowflake.
This is a great help and good advice. I'd have never have thought of neighbours robbing my electricity when I was away. It looked a very clean job. No mess.
You just compromised your IP66 by drilling 15mm hole, the if the socket has a 20mm knockout then 20mm conduit with bush coupler through wall, you can buy long drill bits as cheap as £12 just got to shop around
I agree that he's lost the IP rating as the instructions call for eg a conduit gland. However, pragmatically speaking i feel that installation is more than ip66 water tight despite it not having the certification.
Another brilliant video, I like the idea of flex to socket much easier than having to go back to consumer unit and installing cable and connecting a spur! Very simple effective installation which can be disconnected very easily, truly proper DIY!
I never understood why they changed it from red - surely the most obvious colour... until entering Europe, it seems, where red must have other connotations... ;-)
I work the way you do these days, calm & accurate & don't get flustered... There's more to life than work, I remember when it was my only priority 👌✌️❤️ Subscribed.
Never ever thought about wiring it this way, but I will certainly being doing it from now on, great technique, thanks for the benefit. Have now subscribed.
As a self employed spark with a family to feed, this kind of vid will never sit right with me. Not a bad job you did to be fair for an extension lead (skirting board clipping aside) and luckily most homeowners would rather pay someone like me to hard wire it properly.
Nice one. I used a similar method to have a plug socket 40ft away from my house on my deck, but using armoured cable and an RCD plug to give a bit of extra safety just in case, given the exposed nature of the armoured cable running along my garden fence. 20yrs on and it's still a functioning extension socket.
Thanks for this. I was researching how to power my caravan whilst it sits in the garden and this has been a big help. I really like the way you film and narrate so clearly, i have subscribed 👍
Hi, I just installed an outside socket following your guidance...always terrified to touch electrics up to now.....can't get over it -delighted with result. Many thanks for inspiration
Watching from Canada.. Nice job, the codes are very different here and U.S., They wouldn't allow that type of setup here (essentially an extension cord through the wall) thus braided flex wire is not allowed in that application, and outside plugs (assuming that is 240V), as you mentioned, circuit must be dedicated AFCI/GFCI circuit either at the box or panel. Just did one for my kids electric car and conduit must also be coupled/ secured at the box.
A great video with clear instructions. I would never have thought of fitting an external socket which plugs into the internal wiring brilliant idea thanks.
This is excellent - neighbours robbing the electric hadn't even occurred to me, hilarious. I am about to get an external socket put in for a roof terrace that we are eventually planning, this way is going to be so much easier and cheaper. Good man.
I put internal switches on both external boxes, and a gate valve on the outside tap too. Our yard is visible from the lane and the low gate is no security
Sometimes I watch instructional videos and I'm put off because it's made to look so complicated. Not here... Love your style and the way you explain in simple terms, why you do it the way you do. Keep up the great work
Good video I was thinking of doing this in the summer, One little tip I lent over the years ,when you cut wires to strip (live,earth,neutral) don’t pull the platic completely off the end,it gives you something to grip,then pull off end same time twisting platic and it’s twists strands so easy. (easy on the fingers,no sharp bits of wire)
Hello there. Thanks for that. It helped me to decide as I had this idea in my mind but I was looking for reassurance. Just one query I still have. I have two outdoor sockets. Following exactly your video, I reckon I just need to put L/N/E together, of course, my rookie question is if I should connect another earth wire between the 2 outdoors sockets? It would be nice to see a small continuation of this video teaching that, to be honest. Wonderful teaching. Many thanks, Sir.
Brilliant - I can now install an outside socket without all the hassle of running in spurs which I was led to believe was the way to do it - many thanks.
Cracking idea this, exactly what i was looking for - got a decent sized 20ft x 10ft conservatory in the back and i want to run some sockets into the back garden for my shed and outdoor tool use etc for convenience, this is the answer!
Brilliant I was just going to pay someone to install a socket but this is doable. I have just watched two of your videos... Well presented, to the point and humorous to boot. Subscribed 😊👌
Great video - I've put 3 outdoor sockets around my house all using this technique, connected to my garage. I added RCD plugs for safety but it probably wasn't needed.
Absolutely superb video. Really well put together. I normally end up skipping, but didn't with this one - very engaging. I'm definitely going to give this a go!
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
As an registered electrician with 20 years experience - nice job 👍 I would have charged £150 parts and labor plus certificate for that. ( in august 2021 )
To water proof further I would have run silicon around the whole socket where it is in contact with the wall except the bottom side.
Well thank you very much for the comments - especially coming from a registered electrician - much appreciated!
What I didn't show in the video was 2 days later I had a look at the socket and did exactly what you suggested and ran silicon around the top and 2 sides of the box just to give it some more protection!!!
In addition would you have carried out a earth loop and rcd test to make sure all is working correctly.
@@Phillwin It is legal to do it as a homeowner and ironically because it goes though a 13amp plug is safer as you have an additional fuse along the way. You do need to make sure that you have a RCD somewhere along the route though.
@@jimpaterson9635 I did talk about the required RCD protection and what I have in the video
@@ProperDIY I know, trouble is without conducting a test, you are in the dark as to if the circuit is compliant.
I lost my dad when I was 13, he was always DIY proficient and could fix anything, watching your videos helps me learn cope and learn the skills he always tried to teach me. If you see this I want to say Thank You, for helping fill a void and for being a positive role model.
I am sorry the hear that as it was my Dad that taught me the basics and the reason I've ended up doing what I'm doing, so I totally understand. Thank you for your kind comments and be assured that by watching these type of videos (not just mine) and practicing (and making lots mistakes like I have) you can become extremely proficient, which I'm sure would make your Dad very proud.
Stay strong my friend and keep moving forward
Your Dad is proud of you 👍
Best wishes Eli.
oh shutup
Me too ❤
I haven't finished watching yet, but drilling from both sides and managing to meet needs a compliment no matter what else happens.
Thank you. Careful marking and drilling! - I was determined not to have to spend even more money on a longer drill bit!
Was going to say something similar! aha. I've also not finished watching, but drilling from either side and meeting in the middle is a skill in its own right!
Reminds me of the channel tunnel.
@@georgesmith8988 he'd have needed to leave the drill in the wall....:-)
@@ProperDIY Very good instructional video, I was more concerned about how did you know there were no fixtures in both walls before you made the holes!!!!
I would like to know how did you install that tap on the outside and linking it from the inside.
I have just subscribed.
Drilling from both sides, to stop the outer facet of the brick from splitting, is the sign of a considerate and competent person.
Its also almost impossible to make the holes line up perfectly as the video showed!!
@@richardlewis5316 use a really thin drill first like 6mm, then trhough from each side with 16mm ish.
An underrated part of your videos is good production. I don't mean fancy edits and effects but clear audio and camerawork.
Contents is excellent and succinct as usual. Thank you.
Thank you - much appreciated
Great comment about using the hammer to keep the clips equal distance!
It's the little things that most people won't notice (like the equal spacing of the clips, like the silicone in the conduit) that makes all the difference to the end result.
Only just found the channel so working through the videos, love what I've seen so far! Keep it up!!
Thank you very much - welcome aboard!
Just followed these steps to install an outdoor socket. Great instructions. I now have an outdoor socket and it only took 45mins. Thank you.
Great video and love the idea of a plug inside the house. One tip when drilling holes in external walls, I always drill at a slight gradient keeping the drill slightly lower than the drill bit point. This way, if any water does ever get to the hole and the silicone has failed, the water would run down to the outside and not inside. I would also run a bead of silicone along the top of the external plug unit to be absolutely sure.
Thank you. Good tip - I did think I might try that but was so worried the 2 holes would not line up from either side I thought I would be pushing my luck to them try to incline them as well. I was looking at the socket yesterday and though I might seal around the top and sides as you say - thanks.
@@ProperDIY I'm just wondering if you use (as you seem to have done) a small dril from each side first and then use a larger drill on the outside at an angle (downwards)(and sloping up on the inside) when enlarging the hole for the pvc pipe - you might only need 2-4 degrees...
What cable do I need to buy to wire into this and a plug? Or could I cut the cable and plug off an extension lead and use that?
Wow - I have done any diy - but watching your video's I want to try, Love the garden lights and this video so far
You not only produce fantastic DIY advice and techniques but your videos are a work of precision too, from filming to your detailed advice and instruction......love the channel.
Wow, thank you! I try!
Superb, I am on my own and wanted an outdoor socket for the lawnmower. I have put my socket under the porch area so it is protected from rain etc. but have followed the video and done mine to a plug as well. Wasn't sure that was correct but your video confirmed it was all ok. I did however use electric cable that was suitable for outdoor use. although a bit more difficult to work with. Many thanks.
I do a fair bit of DIY around the house, and I have been agonising on how to wire a socket like this, for ages. I am not a competent electrician, and so I was delaying the installation as I didn’t want to pay an electrician a lot of money! Having come across your video, just by chance, and watching it, has given me a lot of confidence. Your way of describing everything in detail, yet without jargon or confusing words is commendable to the highest. Thank you very much. Now, I’m off to B&Q!
No problem
Well, after looking at so many videos on this subject, I decided that your 13amp plug solution was the one to go for. I think it was the only one with that idea!!. I followed your instructions and found it all worked out well, with one modification, I put the cable in some trunking. Ohh what a game that was!!! But I liked the look as it was in the Living Room. The conduit through the wall was an interesting time, getting to stay in place when sealing it. It kept on moving. Recommend, longer is better than shorter!. Thanks so much for giving me the confidence to do this job
I’m an electrician myself and I like this idea and a very neat installation. Couple of tips When using stranded flex cable I always use ferrule crimps to prevent damaging the stranded cores when terminating. Also make sure the socket you plug into is RCD protected inside the house 👍.
Feral … 🦊 … maybe a bootlace ferrule would be better 😂😂😂
@@andyxox4168 I thought that was an aglet 🤔
Nice to see you’ve corrected ‘Feral’
Using crimps a bit overkill
I've just watched this prior to installing exactly what is demonstrated, and I thank you for the wonderfully easy-to-follow, no nonsense instruction. That was well worth watching. 👍🏻
Thank you Stuart for taking the time to make the video that has now given me the confidence to install a outdoor socket and saved me paying an Electrition to do it for me, made my day.
Glad it helped
Great video, drilling from the inside and outside to meet at the same point was the highlight.
Wow. I was going to get an electrician in to fit one to the house electrics. Done your way, it's something even I could do. Thank you.
Tbh, I found it just as easy to turn off the mains, remove a socket on an outside wall and drill through, wiring the new socket into the interior socket. It's still a very simple task and is neater.
I have two of these boxes to fit.
Thanks for the clear instructions.
I had a friend drill through the cavity wall for me took a couple of minutes for both boxes. If he hadn't done it I would have bought the drill bit. It would have save alot of stress and time trying to line them up.
So many excellent tips.
Cheers 👍🏼
Full instruction from an expert.
I can now install my new fountain with the necessary electrical skills. Excellent.
Thank you.
Glad it helped
Hi Stuart, thoroughly enjoying all of your videos, great content and production. As a former electrician and electrical installation lecturer I agree that this is an excellent option for an experienced DIYer. This method removes the need to safely isolate, test and certify wiring attached to the existing circuit. As you mentioned this is an RCD protected extension lead so a great option for outdoor power. I used to teach the folding over method and the reason is that most terminals on electrical accessories are designed for two cables, so folding a single cable helps to fill the terminal and provide a more secure connection. Keep up the good work!
John, that is very much appreciated coming from an electrician - I tend to get a lot of grief from electricians who do't want to see anyone unqualified even fit a plug. Now I know why the cables are folded - learn something new every day!
@@ProperDIY Hi Stuart, I agree completely that in some circumstances a qualified tradesperson is the best option, but DIYers will have a go. I think you've illustrated a safe method of achieving an identical result to anything an electrician could produce. Do you mind me asking of you've done any formal teaching?
@@JohnCarr43 Thanks! No, no formal training or teaching.
@@ProperDIY A natural then! Your videos are very clear and well produced, (I've currently got a large piece of plywood and several lengths of 2X4 in my garage ready to follow your workbench tutorial!) Looking forward to your next video.
@@JohnCarr43 Nice one! Good luck with the build - new video out today!
What a nice job!
Just completed a similar job, using these instructions, and I have to say - it went about as good as I could have wished for. Kudos to Proper DIY for an outstanding, easy to understand, and thorough approach to the project.
Let's start out with the elephant in the room: Getting an electrician in, tapping into a ring circuit, doing all the tests, and issuing a certificate of compliance is going to cost several hundred pounds. As it should, given the cost of testing equipment, skills of the electrician, etc.
This approach sidesteps most of the costs, while maintaining the safety inherent in the UK electrical code.
Little tip I do with any plug is make the live wire shorter than the neutral and the earth longest, that way if the cable ever gets pulled the live wire is the first to get ripped out
Now that is a very good tip! I've not heard that one before but immediately understand why! Thank you.
Oh yeah, what a brilliant tip, I’ll be using that one in future,thank you
When you wire a plug it's shorter anyway ffs
@@markyd2633 ffs
Yes that was one of the first things taught in college (80s) lecture gave us all a plug top and said wire your plug, only two of us got it correct, always have the live wire taught and a big curl in the earth, doesn’t matter if the live comes out means the appliance won’t work but the earth should never come out first.
Great video.
The ‘RUclips algorithm’ suggested your garage door video. I was impressed by your presentation, so watched some more of your videos. I may copy your workbench. Your channel deserves to grow 😀
As an industrial maintenance electrician I can confirm that this is the best method for a DIYer to fit an external socket, and for me too as there is no need to be part P registered as existing circuits are not altered. You have shown how to safely install a fixed, waterproof extension lead. I would echo the comments regarding using ferrules to keep the copper strands secure in the socket terminals, but your twisting then folding of the copper wires is the next best solution. Nearly all connection issues I encounter are caused by the screw becoming slack against the copper wire over time, by filling the terminal with more copper wire the strands are less able to move as the screw is tightened ensuring that when tightened the connection will remain tight.
Thanks!. Good, sensible comments which I agree with. I'll have to look into the ferrule addition - I've never used them. Great to get feedback from a calm, logical electrician.
Thank you so much for simply sharing all the vital information with no waffle and no speed talking. 👍👍👍
Thank you
Very clear, in plain English and the gentleman speaks slowly so that everyone understands. He makes any hard job looks simple, well done. I'll be copying excatly what you did when installing mine. Keep up the good work, waiting for more useful DIY vedios. Thanks
Thank you
I've been thinking of getting a sparky in for this as I didn't fancy messing about with electrics but your way is really easy for a competent DIY person such as myself. Thanks for such a great informative video :)
No do it yourself 100% don’t get ripped off by a sparky just to basically fit an extension lead lol
I'm an electrician and this is a great instructional video, the silicon and the pipe was a nice touch too
Thank you so much! All I tend to get from Electricians is grief so nice to hear this from you!
Are you sure you’re a qualified sparks Andy?
Yes Im positive, as long as this is terminated correctly and RCD protected it's perfectly safe imo and would do it in my own home. Probably wouldn't if I could back to back it off a socket but it has its place,cheers
You could also do a slight angle for the external hole, so that any water natural drains Down and out
I believe that is essential . Water trickles down the inner face of the outer bricks or blocks within the cavity. If the duct is horizontal or sloping back into the house the water will pass to the inner leaf of the cavity wall and potentially cause dampness.
@@chapman9230 Aa
@@chapman9230 It has mastic on it so not necessary at all. The cavity (depending on year) should have trickle vents to let out water/condensation which builds up.
@@mrfr87 the cavity I was talking about is the cavity of the house wall
@@chapman9230 yes....so drill at an upward angle 🤦
I think I might do this myself. I've had enough of dragging an extension lead and hose on a reel from the exterior socket and tap in the back garden whenever we wash the car. The only sensible option for power is the sockets under the front room window. That'll work. No trailing cables and no trailing hose as I've fixed it to the side of the house and all we need is a short length to attach when washing.😊
Follow up: installed as I said I would but also added an alexa based wifi plug to operate it. Added a LED driveway light on the first floor powered in the same way.
Both voice activated, bloody clever stuff! I've even turned the light on from a different country!😂
Another great clear concise video! I've recenty taken to crimping ferrules into the end of copper flex after exposing the copper. Looks neat and stops them getting messy if you need to readjust things 👍
Thank you. Thats not something I've ever done but want to give it a try - maybe a future video!
Yes, I bought a ferrule crimper for flex connections. Only other thing I would have done was to put a cable tie around the flex exiting the inside box, just to stop it getting pulled if something gets caught on it.
Just found your channel as I am looking to put a socket on the outside wall of my new porch. Nice easy guide. Just the job mate, thanks.
No problem
Exactly what I needed for a spot if DYI in the new house. Love this video, simple, clear instructions and advice. Love this guy 👏🏾
Thanks for watching!
I've just done this after watching your video. Decided to run the cable round the back of the fridge freezer. After moving the fridge for access all going well but then noticed the freezer door screws were really loose and door hanging off. The screws holding it on were not doing anything and had no bite left, no wonder it had been leaking. so then spent the next few hours taking fridge freezer doors off to fix it all. So now got a double socket right next to shed and a fixed freezer :)
Glad to have found a proper UK DIY channel. Keep up the good work.
Thanks, will do!
My complements on a real clean job. Your broom breaking on your intro vid makes me chuckle
Glad you enjoyed it
Just done two of these today and I’m pretty useless at most stuff, but they turned out fantastically. Thanks for this video. I had to get myself 40cm drill bits, but for £8 (for 8, 10, 12mm) it’s a no brainer). 👍
Nice one well done!
Did you use an SDS drill?
Would you ever consider running the flex in a conduit along the top of the skirting.
Just did this at the rear of the house, all good. Am going to do the same at the front now. Thanks very much. Just subscribed.
Hats off to you for producing a video that is easy to understand and follow. Your instructions are clear and concise and I particularly like the fact that you explain why you are doing something a certain way. subscribed. You have given me the confidence boost to actually do the work myself PS Why hadn't I ever thought about using my hammer to space out clips ? I certainly will from now on. I am off to buy my outdoor switch - wish me luck.
Hi there, I just want to say I absolutely love your videos. Unfortunately I did have a dad who didn’t really teach me much and wasn’t really a part of my life. But I just wanted to say that I absolutely appreciate all the hard work you do. Thanks to you. I have installed new sockets in my stepdaughters office managed to put electrics outside the House and many more things that you talk people through.
I suppose growing up, not being taught anything, it just looks all scary
But when you put your mind to it and follow the basic steps how you put your content out it’s not that scary. I suppose it’s like riding a bike once you keep doing it you get better it every day but I just really want to thank you and appreciate your service.
Like everybody else this has saved me hundreds of pounds getting chippy, Plumber, And Sparky, in
I think you’ve mentioned it before. Did you say you had a membership page? As you clearly have saved me a hell of a lot of money. Dave
Great content. I needed an outdoor socket for my daughters rechargeable sit on car and my hot tub. I followed this process and it solved the problem I had. Great advice and I'm chuffed with my new outdoor socket. I also like the fact that I can isolate the power to the garden from the house. Took me a couple of hours to get everything done but works really well. Thank you 🙂
Glad it helped
Stuart many thanks for this video I have successfully installed my outdoor socket. Neighbours all want one now I stated watch Stuart and you can do it but most want me to do it, lol. Thanks again
Thanks. Well done on the socket - that's the price of success!
Really excellent content, thorough and to the point. Everything you do is done well and thought out, which means the job can’t fail. I can’t tell you how much difference it makes to see someone doing this. You are passing on great skills. Thank you.
Well thank you very much for your comments. I always think out projects before they start and especially if I'm on camera. Anyone spending 10mins+ whatching me should, I think, deserve to leave with at least with good tip or a laugh or 2.
@@ProperDIY yes and what strikes me is that many jobs, like this one, are actually a series of smaller jobs, each perhaps requiring a basic skill. Your video didn’t assume that I knew how to do anything, no missed steps, but at same time you managed to keep it from being long winded and patronising.
@@michaeltester5187 Thank you again. It's actually a difficult balance to show everything, be entertaining, miss nothing and not make videos 50 mins long!!! I'm always concerned that I will fail on one of those.
@@ProperDIY for me, you are getting it right!
@@ProperDIY entertaining and educational.
Did you have many outtake in your vids?
Haven't done a socket in sometime...it was a great reminder how do it again..and I agree with putting a plug on ,as opposed to wiring directly...for all the same reasons you outlined...a very helpful video..cheers pal..
Glad it helped
Jeepers where have you been all my life mate???? That is fantastic thanks and I look forward to binging on your videos...
Thank you
Really great video Stuart where people can do things for themselves but safely which is really important too. Thanks!
Good advice - well put across. These skills and tips clearly apply to many DIY situations. Thanks
Glad it was helpful!
Great info.
Wow, I had no idea it was so easy. I will be cancelling my electrician and doing it myself. Thanks so much for the video.
Great video, you present them really well. Any chance of making a video on fitting wall plugs and what size to use, and drill size needed for each plug? I'd find that useful, thanks.
Will do
Google
Thanks for your help on fitting the outside socket. I purchased the same product from Screwfix + 16 mm drill bit to go through wall + plumbers pipe all same day. All working fine and making such a difference instead of running x lead from house. 👏👍😉
Nice one - well done. And, you can easily remove it from the house supply if there is any problems - handy over the summer.
It thought you would wire that into the ring but then I saw you wanted to add a timer or WiFi remote and that made perfect sense. Nice tidy job
Thank you
This is just the channel I need.. I have no Trade and can’t really afford to pay for all the little jobs that make the home more comfortable.. 👍
Good to see ‘proper DIY’ being shown. 👍
Thanks
At last! New viewer and I have subscribed as you do d-I-y at my level (trimming the cable!) lots of channels say for a amateurs but then do stuff I will never do! And with you use UK t&c’s.
I just paid for a spark to fit an outside 13amp supply “because it had to be terminated to the mains” , I never considered a simple plug top…….I could have done all this very happily.
You, my man, you could save me cash whilst educating me!
Bob
England
Very nice comments- thank you!
Very impressed and I totally agree its the safest DIY method and also with the added bonuses you mentioned . One tip if using a set of pliers to strip back the insulation on the cables, is to do exactly what you did with the knife and score round first (basically griping the cable in the cutting edge and turning the pliers clockwise and back a couple of times ; this prevents both you gripping too tight and cutting it off completely and also helps prevent pulling the odd strand off too .. (apologies if this is mentioned below - 884 comments at the time of writing) 30+ years ago when doing my apprenticeship, we were always told to use strippers (cable ones!!!!) but, after a bit of practice you know just how tight to grip and it saves a bit of time as you can strip, cut and bend all in one go (so to speak! 🤔)
The only down side of this is that you take away one of your internal sockets availabilty. Rather wire as a spur or better still as part of the ring main, but it would then require sign off
Another top tip filled vid, i see your point with the cable clips i normally put a well positioned 6 inch nail straight through the cable every 6 inches to make sure the cable is firm to the wall and have no concerns over safety as when its all plugged in i normally get the neighbors kids to stand in a bucket of water and lick the cable and switch so far no issues, keep the vids coming as they are very helpful.
P,S top tip about the remote switch for the power i will wire in the mother inlaws chair and see if it lights her up from a safe distance taking into account health and safety guide lines
I particularly like the tip of getting the neighbours kids to lick the cable when well grounded - back to basics!
This couldn't have arrived in my feed at a better time, trying to find an electrician to put in an extra plug into our new to us home is a nightmare, having this idea means I can do it myself and save a couple of hundred dollars and still be safe! Many thanks and hi from New Zealand.
Good timing then!
Watching your video I have installed socket outside it’s save me lots money and time thank you very much I really appreciate your you’re videos very helpful very simple thanks again
Thanks!! Great to hear some down to earth advice without all the clap-trap we hear from some presenters.
P.DIY is always my first port of call when I embark on a project. I always learn something.
Glad to help
Good shout on doubling the bare wires, goes in the connections perfectly 👍🏽👍🏽
“If you don’t trust your neighbours “ 😂
As a DIYer I'm very happy I found your channel I have all ready subscribed.i have checked out a good few of your videos and they are all very informative and helpful and plenty of safety tips too
Popcorn at the ready. Keyboard electricians.. get set... GO !!!
I'm an electrician and have no problem with DIYers as long as it is done safely and in compliance with current regs.....
Good stuff. I like to pin the conductors if they are stranded and the connection is screw type as opposed to clamp, just for good measure. I've seen stranded conductors get damaged over time where the screw presses into it and make imperfect contact. Probably why the newer method insist on doubling down the exposed wire.
I was going to spur off from one of the sockets.
Now I’ve seen this, I’ll now do it your way 👍🏻
I think it's an easier and safer way than going for a fixed spur
Good choice as outside sockets should not be wired to the internal ring main. They should be on their own RCD in the consumer unit.
Did this on Wednesday this week works perfectly saved me a lot of pennies 👍
Nice work!
Lost your IP rating when you didn’t use appropriate gland. Would drill drainage hole when using rear entry.
congratulations - You are the first keyboard electrician., I know you just couldn't help yaself so please collect your pedant award.
Everyone knows how cable glands are totally impenetrable to water and silicon is basically a water sponge and magnet all in one!, what was he thinking!!!!
@@mattsan70 wow what a comment. Not a keyboard electrician at all. In the video he says he paid for an IP rated fitting and doesn’t want to drill a hole as it will lose that rating, all I’m saying is he’s lost that rating already so should drill a hole. Didn’t slag off the work, but clearly you’ve taken offence, so here is your award for being a snowflake.
This is a great help and good advice. I'd have never have thought of neighbours robbing my electricity when I was away. It looked a very clean job. No mess.
Glad to help
Wouldn't a cable gland have been easier than all that silicone?
Thats why there are DIY ers . A pro wouldnt do it like that. Plus the socket is too close to the outside tap. The regs stipulate a set distance.
A rubber grommet that fits the knockout hole might be even better as it has a much smaller size.
Great video. I will attempt this soon.
Would live to see a video on how to install power to a garden shed.
You just compromised your IP66 by drilling 15mm hole, the if the socket has a 20mm knockout then 20mm conduit with
bush coupler through wall, you can buy long drill bits as cheap as £12 just got to shop around
I agree that he's lost the IP rating as the instructions call for eg a conduit gland. However, pragmatically speaking i feel that installation is more than ip66 water tight despite it not having the certification.
Another brilliant video, I like the idea of flex to socket much easier than having to go back to consumer unit and installing cable and connecting a spur! Very simple effective installation which can be disconnected very easily, truly proper DIY!
Thanks. I like it when from your comments I know you have 'got it'.
i always remember the live wire is brown as that’s the colour your pants go if you touch it!
I never understood why they changed it from red - surely the most obvious colour... until entering Europe, it seems, where red must have other connotations... ;-)
@@harryinhuahin1272 red is used in alot of control wiring
I work the way you do these days, calm & accurate & don't get flustered... There's more to life than work, I remember when it was my only priority 👌✌️❤️
Subscribed.
Exactly! Nice one
Hahaha i love the encouraging "go on, comment, but im not drilling the drain hole"
Thank you
Never ever thought about wiring it this way, but I will certainly being doing it from now on, great technique, thanks for the benefit. Have now subscribed.
👍
As a self employed spark with a family to feed, this kind of vid will never sit right with me. Not a bad job you did to be fair for an extension lead (skirting board clipping aside) and luckily most homeowners would rather pay someone like me to hard wire it properly.
Ensuring the outside socket had some form of RCD protection as well.
Let's not be a hypocrite....
No one owes you a living
🧂🧂🧂🧂🧂
Nice one. I used a similar method to have a plug socket 40ft away from my house on my deck, but using armoured cable and an RCD plug to give a bit of extra safety just in case, given the exposed nature of the armoured cable running along my garden fence. 20yrs on and it's still a functioning extension socket.
Good job done perfectly. Proper old fashioned electrical work and common sense
Thank you
Thanks for this. I was researching how to power my caravan whilst it sits in the garden and this has been a big help. I really like the way you film and narrate so clearly, i have subscribed 👍
Hi, I just installed an outside socket following your guidance...always terrified to touch electrics up to now.....can't get over it -delighted with result. Many thanks for inspiration
this is one of my favourite channels. please continue to make videos , great work
That's a very nice comment. yes will be continuing
Watching from Canada.. Nice job, the codes are very different here and U.S., They wouldn't allow that type of setup here (essentially an extension cord through the wall) thus braided flex wire is not allowed in that application, and outside plugs (assuming that is 240V), as you mentioned, circuit must be dedicated AFCI/GFCI circuit either at the box or panel. Just did one for my kids electric car and conduit must also be coupled/ secured at the box.
I was looking for a comment along these lines. I also noticed the PEX connector, and I wasn't sure if that would fly. Any knowledge of that?
Installed my unit today using the recommended RCD socket. Very pleased with the result. Thank you.
Nice one!
Fantastic way of putting in an outdoor socket thank you for making this video
A great video with clear instructions. I would never have thought of fitting an external socket which plugs into the internal wiring brilliant idea thanks.
Glad it helped
This is excellent - neighbours robbing the electric hadn't even occurred to me, hilarious. I am about to get an external socket put in for a roof terrace that we are eventually planning, this way is going to be so much easier and cheaper. Good man.
Glad I could help!
I put internal switches on both external boxes, and a gate valve on the outside tap too. Our yard is visible from the lane and the low gate is no security
ive just installed my own copying this method i also ran silicone on outside except bottom….thanks for the video 🤟
Sometimes I watch instructional videos and I'm put off because it's made to look so complicated. Not here... Love your style and the way you explain in simple terms, why you do it the way you do. Keep up the great work
Thanks so much 😊
Well thank you very much. I try to explain things as much as poss while keeping the video moving and not making it last 50 min!
Good video I was thinking of doing this in the summer,
One little tip I lent over the years ,when you cut wires to strip (live,earth,neutral) don’t pull the platic completely off the end,it gives you something to grip,then pull off end same time twisting platic and it’s twists strands so easy.
(easy on the fingers,no sharp bits of wire)
Good tip.
Hello there. Thanks for that. It helped me to decide as I had this idea in my mind but I was looking for reassurance. Just one query I still have. I have two outdoor sockets. Following exactly your video, I reckon I just need to put L/N/E together, of course, my rookie question is if I should connect another earth wire between the 2 outdoors sockets? It would be nice to see a small continuation of this video teaching that, to be honest. Wonderful teaching. Many thanks, Sir.
Brilliant - I can now install an outside socket without all the hassle of running in spurs which I was led to believe was the way to do it - many thanks.
Glad it helped
Thanks, a really good and informative video. I want to install one for our hot tub and wasn't sure if I could, but now feel very confident that I can.
Amazingly easy to follow, safe and practical method. I used the RCD version - most pleased with it, hank you.
Great to hear!
Cracking idea this, exactly what i was looking for - got a decent sized 20ft x 10ft conservatory in the back and i want to run some sockets into the back garden for my shed and outdoor tool use etc for convenience, this is the answer!
Nice one!
Brilliant I was just going to pay someone to install a socket but this is doable. I have just watched two of your videos... Well presented, to the point and humorous to boot. Subscribed 😊👌
Thank you
Brilliant, thanks. I think I'll see if I can get a rubber grommet to give a water-tight fit for the hole and the pipe!👍thanks for sharing.
Good Idea
Excellent video. Clear, concise and confident. Many thanks for showing.
Glad you enjoyed it!
Great video - I've put 3 outdoor sockets around my house all using this technique, connected to my garage. I added RCD plugs for safety but it probably wasn't needed.
Well done - they will come in handy I'm sure.
Hopefully you ran them off a fused spur. If they're all spurred off the same socket, you're looking at a potential fire hazard.
@@BobBobOnRUclips separate sockets for each - no bother
@@AutoAbsolute Cool.
Absolutely superb video. Really well put together. I normally end up skipping, but didn't with this one - very engaging. I'm definitely going to give this a go!
I'm glad you liked it