I was able to fix my drone that had error code 40002 after crashed, I watched your video and able to fix it replacing cable for $50 dollars, Now my drone is back flying again. Thank you!
Thank you! although it was slightly different for the Mini pro it ended up working. So fyi for anyone. If your gimbal starts to stutter/shake midflight cable will eventually fail. I crashed my drone and gimbal still worked for a while after, then it started to stutter during flights and eventually gimbal was failing completely but camera was 100% fine. I replaced the cable today and everything works like new! no error codes to.
@@maryjteraji Sorry I saw this very late. But no suggestions on my end. That was my first time every opening / fixing a drone. Till this day that what caused my failure.
after a crash I have error 40028 gimbal blocked and I have the impression that the rubber has turned over but the gimbal is completely free. Will the video be impacted? can I still drive?
help me plase... i have the same issue on 3......gimbal stuck.check whether gimbal cover is removed and make sure gimbal can rotate freely on all three axes this is from a landing erros...😁 what can i do....the camera stops moving.
Great detailed video, I’m watching because I have one that will need to repair. But question aside, what camera do you use to record the videos? Has a great focus on the details!
Amazing tutorial, Thank you so much for detailed walkthrough. I was successfully able to change Gimbal wire. In my case, error 40028 still appears after gimbal calibration and after couple of minutes for flight, I'm getting "Gimbal Motor Overload" warning. Any solution for it?
@djiSolutions what is the size of the 1st two black screws you removed from the battery port? The screwdriver that came with my cable kit stripped the screw head
If you still have stuck gimbal, the problem still not fix. I know if hard to find out without the tools. You should have cable tester tools first. Link in the description
I have one same issue with my Mavick 3 Mini. My sister crashed it, and I saw one of the mini cables ripped apart. Could I not get it solded and joint the cables Back together? I mean, the cut appears at simple eye view. Or do I have to replace the whole cable?
I was able to fix my gimbal after replacing the ptz cable. But now I can't focus the camera no matter what I do, even manual focus does not work. Would it be safe to assume that if even a single ptz wire on the camera connector section is broken that it can render the camera's ability to focus as useless? There are about 20 wires going straight to the camera alone. If anyone wants to chime in on that possibility please respond. There are very few threads even covering this. If we could save eachother some money that would be great thanks
@@melroy16 No guarantees but I did manage to fix the focus issue. You need to make sure that the PTZ cable end going to the camera inside the gimbal has a very secure and snug connection(keep in mind that the PTZ cable has about 20 individual thin wires that control different aspects of the drone). To do that you need to carefully apply enough pressure with your fingers on the PTZ connection going to the actual camera. If I remember correctly you can even test the camera before re-assembling the drone by connecting it to your phone via Bluetooth. Then from there see if your dji fly app controls let you focus the camera in and out before reassembling it. If it doesn't try your best to fit the ptz cable connection to the camera until you get focus running again. Of course be very careful, those PTZ wires can be very fragile and you don't want to break any of them. When you get the desired result with your focus controls take your time reassembling the drone as any harsh wiggling of the hardware can potentially pull on the PTZ cable messing with the snugness of its connection to the camera. Lemme know how it goes
my mini 3 have a 40002 error code then i replace the ptz cable but wont solve my problem still have a 40002 error code my dji mini 3 is 7 days old avoid warranty because of the crashed what can i do next ?
what happened to me is that the gimbal has somesand in it after a crash, it also have some sand in the rotors but I'm managing into cleaning it, but i feel I had to clean the gimbal motors cause it is making them to overload or something like that then I had to stop flying for some time
i tried to do ... but, when i completed the task, the camera seems to be offline, dead, black screen. Before, it was working, but one of the axis was damaged. So, did i burned out my camera ? ... btw ... there is a cable (black and red) in 2.35, connected to the camera... i didnt see this cable... very strange ... maybe my drone was a different version. And... i have recently done this procedure with a mavic pro, and it was a successful! !!!
Things are fine!!! The problem was the cable.. Aliexpress sent me a bas cable. I hope next time they send me a good one! Wonderful vídeo!!!! ..the must hard part are to connect the 4 joints ❤
My gimbal works but no video are seen on the phone display. Can it still be the cable? The screen went black yesterday after it said the fly app had bug fixes problem and i could not even start the app then.
I fucking fixed it then when i was about to put back the side case manage to fck it up because was trying to put back the cable I fcking bent the wire of the ptz cable, what a day.
![DJI Mini 2 Flexible Cable Also Cause Stuck Gimbal [ Error 40002 ]](/img/1.gif)
I was able to fix my drone that had error code 40002 after crashed, I watched your video and able to fix it replacing cable for $50 dollars, Now my drone is back flying again. Thank you!
Thank you! although it was slightly different for the Mini pro it ended up working. So fyi for anyone. If your gimbal starts to stutter/shake midflight cable will eventually fail. I crashed my drone and gimbal still worked for a while after, then it started to stutter during flights and eventually gimbal was failing completely but camera was 100% fine. I replaced the cable today and everything works like new! no error codes to.
Any suggestions for if I did replace the cable, and I still get the Gimbal Stuck error code?
@@maryjteraji Sorry I saw this very late. But no suggestions on my end. That was my first time every opening / fixing a drone. Till this day that what caused my failure.
Where i buy the tools you use ?
You didn’t include the link for the rubber gimbal mounts. It’s all I need 😩
after a crash I have error 40028 gimbal blocked and I have the impression that the rubber has turned over but the gimbal is completely free. Will the video be impacted? can I still drive?
help me plase...
i have the same issue on 3......gimbal stuck.check whether gimbal cover is removed and make sure gimbal can rotate freely on all three axes
this is from a landing erros...😁
what can i do....the camera stops moving.
Hey. Do I need to remove the top of the drone in order to remove the plastic rubber protectors of the gimbal?
Great detailed video, I’m watching because I have one that will need to repair.
But question aside, what camera do you use to record the videos? Has a great focus on the details!
Amazing tutorial, Thank you so much for detailed walkthrough. I was successfully able to change Gimbal wire. In my case, error 40028 still appears after gimbal calibration and after couple of minutes for flight, I'm getting "Gimbal Motor Overload" warning. Any solution for it?
Your tools that can open the case of drone . I want to buy it. Please tell me where to buy.
I buy from the market 😂 find any place sell phone repair tools
@@djiSolutions aliexpress u find! but... pay attention to do not buy the wrong cable!!! there are 2 main cables inside, .. flat cable riboon cable
@djiSolutions
what is the size of the 1st two black screws you removed from the battery port? The screwdriver that came with my cable kit stripped the screw head
Lolz 😂
Are there more than likely t4
@@djiSolutions i know lol......its wild mane
awesome video! Thank you thank you. Fixed my drone.
You're welcome!
I have changed the ptz cable, yaw motor but still not motion. Any idea on what else issue could be? Camera is working on drone
If you still have stuck gimbal, the problem still not fix. I know if hard to find out without the tools. You should have cable tester tools first. Link in the description
Was curious about the remote removal of the code? What is the best way to contact?
Check the description
I have one same issue with my Mavick 3 Mini. My sister crashed it, and I saw one of the mini cables ripped apart. Could I not get it solded and joint the cables Back together? I mean, the cut appears at simple eye view. Or do I have to replace the whole cable?
Unfortunately I break the red wire linked to the camera lens heating ring, could be the reason why there is a camera error?
Hi, what happens if you get the code 40002 but not the code 40027, is this still the same issue or could it just need normal calibration?
Thank you! My gimbal is working again with an 15$ cable from ali :)
Nice work!
e quando tá no alto já filmando e trava o gimbal ? o que seria
Sorry don't understand
And what is the name of that tool
I was able to fix my gimbal after replacing the ptz cable. But now I can't focus the camera no matter what I do, even manual focus does not work. Would it be safe to assume that if even a single ptz wire on the camera connector section is broken that it can render the camera's ability to focus as useless? There are about 20 wires going straight to the camera alone. If anyone wants to chime in on that possibility please respond. There are very few threads even covering this. If we could save eachother some money that would be great thanks
having the same focus issue , how did you sort it ?
@@melroy16 No guarantees but I did manage to fix the focus issue. You need to make sure that the PTZ cable end going to the camera inside the gimbal has a very secure and snug connection(keep in mind that the PTZ cable has about 20 individual thin wires that control different aspects of the drone). To do that you need to carefully apply enough pressure with your fingers on the PTZ connection going to the actual camera. If I remember correctly you can even test the camera before re-assembling the drone by connecting it to your phone via Bluetooth. Then from there see if your dji fly app controls let you focus the camera in and out before reassembling it. If it doesn't try your best to fit the ptz cable connection to the camera until you get focus running again. Of course be very careful, those PTZ wires can be very fragile and you don't want to break any of them. When you get the desired result with your focus controls take your time reassembling the drone as any harsh wiggling of the hardware can potentially pull on the PTZ cable messing with the snugness of its connection to the camera. Lemme know how it goes
@@soundoverdose3134Thanks for getting back , i did try it all but i guess it was a faulty cable . Ended up selling the drone for spares .
Perfect. Thx Anysugetion where to get parts from ? Thx
AliExpress
Why you need to replace the shock absorption?
After my crash, the rubber mountings were stretched and distorted.
Thanks for the content. In the event of a fall, which is more likely: cable or motors? I have video, but the gimbal is stuck.
Mostly is Cable
@@djiSolutions thanks!!
my mini 3 have a 40002 error code then i replace the ptz cable but wont solve my problem still have a 40002 error code my dji mini 3 is 7 days old avoid warranty because of the crashed
what can i do next ?
First thing is change cable then change gimbal
what happened to me is that the gimbal has somesand in it after a crash, it also have some sand in the rotors but I'm managing into cleaning it, but i feel I had to clean the gimbal motors cause it is making them to overload or something like that then I had to stop flying for some time
What is this cable called and how much does it costs?
Ptz cable mini 3
my Dji mini 3 has ERROR 180016, 180017,180031. errors in the lower visual sensor
did you manage to fix these errors?
When the drone is turned on, the gimbal does not move and a buzzing sound appears. do you know where the problem is?
It can be cable or gimbal
What Did you do? I have the Same Problem
@@achimmi7164 the problem lies in the flexible cable. and yes you will see after that your drone returns to normal
@@jann_dji thx i buy a new Signal cable
Its working! thank you
Good job 👏👍👏
Excellent video, thanks
If you have no error codes but your camera gimbal is somehow vibrating when u turn on the drone producing shaky videos
i tried to do ... but, when i completed the task, the camera seems to be offline, dead, black screen. Before, it was working, but one of the axis was damaged. So, did i burned out my camera ? ... btw ... there is a cable (black and red) in 2.35, connected to the camera... i didnt see this cable... very strange ... maybe my drone was a different version.
And... i have recently done this procedure with a mavic pro, and it was a successful! !!!
It ok my friend, broken 3 or 4 drones, you will be come expert
Things are fine!!! The problem was the cable.. Aliexpress sent me a bas cable. I hope next time they send me a good one! Wonderful vídeo!!!! ..the must hard part are to connect the 4 joints ❤
thanks!!
You're welcome!
How find your telegram please😔
My gimbal works but no video are seen on the phone display.
Can it still be the cable?
The screen went black yesterday after it said the fly app had bug fixes problem and i could not even start the app then.
I fucking fixed it then when i was about to put back the side case manage to fck it up because was trying to put back the cable I fcking bent the wire of the ptz cable, what a day.
It ok my friend, I know your feeling. But don't worry, broken 4-5 drones, you will become expert 😄
HAHAAHAHAHAHAHAAH I just forgot the foam under the ptz main clip, when i put it back and tightened it works great. From 200 dollars qoute from dji to
Nice work! 😄
I took apart the gimbala and then it worked
is it just me or did I see a "sister voice message"
Fantástico
Thank you so lovely comments 😍
I fixed my drone
Your sister is calling
Yes
Who the fuck do you think I am
Exactly!