How to Fix DJI Mini 2 GIMBAL STUCK Error 40002
HTML-код
- Опубликовано: 6 сен 2024
- How to Fix Gimbal Stuck on DJI Mini 2 with the Error 40002. It easy to fix the error 40002 of Dji Mini 2. You have to Teardown your Mini 2 Gimbal Stuck. You also apply can fix the error 40002 Stuck Gimbal with Dji Air 2 or other Model of DJI drone.
s.click.aliexp...
s.click.aliexp...
s.click.aliexp...
Feel Free to Contact Us for more Information about Remotely Fix 40011 and 40021
Telegram : t.me/djisolutions
Whatsapp : +85589898982
I was afraid to do it by myself, but I tried and it works !!! Really thank you ! At service they want to place new gimbal for 180 €
Glad it helped! ☺️
1st time opening any Drone. Everything went well. Issue resolved. U r a lifesaver. God bless u
Glad it helped
Just try that and it’s still stuck 😢
I read the comments hoping they were not fake. They were not, it fixed mine, thank you so much !
Thank you so much for your review 🥰
Ok so for people who just cant make their camera to go down or up and seems like its stuck and has debree in it. I think i found a solution where there is no need to open the drone. I cant open it as well cause the screws are way to tight.
So the solution i did was i tilt the drone where the camera is directed towards the ground and then i massage the camera up and down until i feel that there are no more stuck debrees inside the gimdal. I believe doing this somehow made my foreign object somehwhat fall on the ground as i was massaging it.
In any case i hope it fix your annoying problem.
Note that there are probably still small debrees inside which makes it kinda viable to open it up and clean it but yah. I just hope mine only has that single sand in it.
i just did all of your step and my drone is good to go. i suck doing the dampeners till i finally get it right. thank you so much for this video!!! mabuhay!!!!!
I so happy to hear that 😍
What steps? Get a can of dust busters, he’ll just blow hard on it, worked for me
@@mikesmith4053 congratulation 🥰
I also tried this and it worked! skeptical at first, but I had the right tools and this worked on the first try.
So happy to hear that, you are awesome 👍
Awesome! I'm gonna fix mine using your video. Thank you so much😍
Right now my issue is that the gimbal moves around during the starting sequence but gives me the 4002 message once I connect my phone to it
Error 40002 is hardware error. You have to find the problem and the error will gone automatically
Hello, thanks for your tutorial !
I was wondering if you have have to change the gimbal housing stabilizer, I've crashed my drone and the stabilizer broke one of its legs, and lost some rubber in the process.
I've bought the replacement of these parts, but then there's a roller which I'm afraid to disassemble since I might break it.
If you have any video on that please let me know.
Thank you
I got right up until removing the cover from the drone camera and it’s just a steel plate so can’t lubricate the camera head! Process still fixed the issue by just lubricating surrounding parts
Is what you were blowing through the yellow tube compressed air?
luckily it was grass terrain, so the gimbal was just moved out of it's socket, if it was concrete it would be bye bye... my second crash and first drop from the sky -survived, uf
i did this to mine but before i even opened the gimbal i figured out it was the cable connected to the mobo. But thanks to you I know how to fix it!
You're welcome, good luck
Good afternoon. After the fall, I had to replace the 3in1 cable after it broke, but error 40002 did not disappear. After starting, the gimbal works on all axes and then the cable (3in1 which was replaced) gets stuck and starts to heat up in the place of attachment on the gimbal board (on top).
super helpful tutorial, thanks! looks like i didn't need to buy a new gimbal replacement
If it work, we don't have to change gimbal. 😍
I tried this and the step by step was easy to follow. Thank you for that. Unfortunately it didn’t resolve the issue. My story, as many I’m sure, hit a tree and it fell and crashed. Replaced a propeller and tested it out and it worked great. Tried it again and then the stuck gimbal error occurred. Should I just send it to DJI? Or try something else? Appreciate any suggestions given.
Sure sometime it not working, but before you change gimbal, you should change both gimbal cable first because it cheaper and broken cable also can have stuck gimbal too. Good luck
I just received a replacement mini 2 in the shrunk wrapped package and got gimbal stuck message right out of the box! I am not happy.
Where are you based at ?
What is liquid spray are you using for cleanings
WD 40
Hey ! Does this can fix my drone if the motor still turn when I turn on my drone ? Or if the motor work when I turn on my drone but then don't work with the controler I have to change the cable ?
If you still have stuck gimbal error, It can be cable or gimbal itself
Becarefull to open check the screws all else it will broke guitar pick also help
Excellent (and crafty) tutorial! I'll give this a try and follow up.
When you Turn on the drone, the gimbal will turn so look which part of gimbal that work not correctly. Clear that part more then other part.
Wooooow this guide is perfect!!! Very good job
Glad it helped!
YOU LEGIT SAVED MY BUT THANK YOU!
You welcome, I so happy to hear that👍👍👍
Чётко все сработало , спасибо. И главное без болтовни 👍
Oh wow.... so the motors inside were trashed.... probably full of sand and microrocks... you stripped it all RIGHT DOWN to base components in the gimbal? Clean it off and put it back together for it to work?
That's super impressive honestly. A lot of patience for a lot of taking apart small motors and cables
It really work if your motor still working good. But if we just take it to the service center, they do the same thing but if it's not work, they will change the gimbal.
The motor near the camera is hot, what's wrong with 4002 error, please reply, thank you
Motor is overload, change the motor. Error 40021? Is camera Serial number not match. We have to rewrite the serial number to drone.
@@djiSolutions so where can i buy the motor?
I have dji mavic mini . The problem in my drone was gimbal stuck and imu error (40002&40021) . After this problem , i change the whole gimbal set and 3in1 flex cable . But Bad luck its still not working like previous gimbal . Only top motor move when i start the drone . The roll and pitch motor don't response. Can you help me 🙏🏽🙏🏽🙏🏽
Check the cable too, the Flexible cable break also have error stuck gimbal
If gimbal is not moving like when starting like normal. Is possible a cable was broken? Is that easy to fix? Or I will need new gimbal+cable?
Always check cable first because it mostly broken and cheap too
top!
What is the white paper you placed back into the gimbal at 4:03 ?
Any sticker paper to cover the gimbal from dust.
@@djiSolutions thank you 👍🏼
Hi,
I replace the signal cable for camera of Mini 2. When turn drone on about one minute, the motor inside gimbal turned really hot, burn for touch. Is it normal? Or because I cannot recalibrate gimbal, somthe gimbal stuck, anh overheat?
Same thing with me
thanks a lot !! it works for me !!
You're welcome!
Okey, now how do I do this with just a hammer and no black gloves? 😂
You can do that, it will work sometime but most of the time, you have to buy new one 😂
Thanks a Lot !!!! It Works!!!
Congratulation👍👍👍
I have error 40012 on my dji mavic mini. What can I do ro solve?
Super helpful! Thanks a lot!!!
It works.
Thank you 🥰
Same error here. But the gimbal also products a huge sizzling noise and abnormal heat when turned on, like it's trying to do something. I've already removed and cleaned just like your video but not using compressed air. Maybe that's the problem 🤔 I'll try using compressed air
If it not work, replace new gimbal.
Thank you Sir... I got it 🎉
Nice video, I will try it
Thanks
Hi,
I replace the signal cable for camera of Mini 2. When turn drone on about one minute, the motor inside gimbal turned really hot, burn for touch. Is it normal? Or because I cannot recalibrate gimbal, somthe gimbal stuck, anh overheat?
Change that motor. Gimbal never overheat.
what is that white thing he put in?
Que líquido utilizaste para la limpieza de los motores del gimbal
debe ser limpia contactos eletronico
It work, thanks for your video
You're welcome!
Consegui aqui ! Ótima dica. Valeu
We can remotely fix from anywhere you are.
There is nothing easy about that teardown. I just purchased a mini 3, and my first flight I have a stuck gimbal. What crap with no easy fix. What crap!
Good if you have DJI care. It not try to teardown and clean the gimbal. If don't know how to teardown watch my video 😂
@@djiSolutionsAs it turned out, although I removed the pieces of tape, I inadvertently neglected to remove that rubber insert that held the gimbal in place during shipping. Whew!
Bhai mera bhi yehi problem hai kitna caust parega please reply me ❤
i dont understand where was the problem situated ?
Is the tube oil or what lubricant?
WD-40
i cant put back if i do like this
No problem, broken 2 or 3 gimbals, you will have more Experience 😂
Tried everything and it did not work. After a few minutes the gimbal got really hot and I decided to remove the battery. Did I break anything?
Hot gimbal is overload motor error. you already clean it and it not work so you can change your gimbal
@@djiSolutions thanks. Any recommendations on where to buy it?
Sorry it depends on your location or you can buy on AliExpress.
I replaced my gimbal completely but still get this error. Any ideas?
It is the flexible cable that case the stuck gimbal error.
I thought so, but after replacing I still get a gimbal stuck error, and a slight twitch back and forth from the camera.
@@djiSolutions By “flexible cable” are you referring to the wire cable or ribbon cable?
@@bminecreeper check both
I have no clue what your doing much less try it. How about a can of compressed air?
Sure, but make sure it not too strong.
Simple is always best
@@mikesmith4053 lol except when it doesn't work
Can u Fix Error after Gimbal Change?
1000% sure. We can fix error 40021 and 40011.
Unless you're comfortable completely disassembling your drone (and have done it before), these instructions are useless.
Subscribe my channel, next video will more details
Idk man worked for me. Just gotta send it!
@@samueleardley5763 thank you for your lovely comments 😍
Is that work with Air 2s ? If yes . How ?
Try to disassemble to gamble and clean the motor. Maybe it have some dust inside the gimbal.
I did that I found small part broken I fixed it and now the gimbal 10/10
Good job 👍👏
WHAT do you out inside those part? A liquid? What type ?
I blow some air to remove some dusts and use WD-40.
Thanks
My drone also stuck but I already change gimbal
That will cost alot, try to do this first before you change your gimbal
Too many steps might as well get dji to replacement
That is the easiest ways 😂
👍👍
Gimbal Dji mini 2 saya Sewaktu Terbang Miring ke kanan 😢
Calibrate remote control and imu in fly app.
Took mine off, smashed with a hammer, replaced with a refurbished one, seems to work ok now🙂
Good
nah dude just spray a bunch of WD40 in there problem solved
I get this message all the time, it’s very annoying
Teardown your gimbal and clear it with some oil.
@@djiSolutions I will try and use caned air to blow out the dirt before I try taking it apart cause I know I will never figure out how to put it all back together lol
@@casper2yall Not the problem, broken 2-3 gimbals, it will be easy for you. 😂
It’s not really 😂😂😂😂
But I did it, it not always work but we have to do this first before we change gimbal.
So what was the fix exactly? Maybe I missed it? 🫤 seemed like the main thing replaced was the sticker lol
I blow some air from my mouth and you should apply some WD-40 if the motor is not working well.
@@djiSolutions ahh I see, well I just followed the steps. Didn’t see anything broken, maybe a bit tough moving up and down. Well put it together and had the same error. Oushed on the gimbal a little and it started working! So alls well that ends well 😁 couldn’t have done it without your guide! Thank you!