That 3rd hole in the tail cover is for the wires to route through then up and though the tail section to the connection points. Then I used the factory zip tie to snug everything together. Came out very clean. Thanks for the video.
Sometimes the manufacturer will make small updates to the parts after we have shot the install videos. Thanks for watching and sharing your feedback! - Van
last week I received my GSXR1000R 2022 Grea colour, earlier I ordered an NCR plate from STG and I have received it last 2 months hopefully I will install it these days, Thanks for the awesome video and your explanation was super clear.
Ok very instructional video I was completely baked last Sunday doing this job to my 2020 1000R however.. you did not not that the supplied washers given once tightened all the way down still spin and therefore would rattle. I ended up adding one more to each side but this could have been cured with a slightly thicker washer but they missed that or didn’t care. Still a good kit and thanks for the video !
I had the same issue. If you watch the video they are loose in this too. It would vibrate like crazy. 200$ for a plug and play kit and I had to go to home depot for washers.
Just followed this step by step install video you put for the Gsxr1000R. Super easy and glad i went with this set up. Ordered from Joe, thanks Brian for doing a kick ass job putting this together!
Thanks for the vids!! Made that look easy. The kits updated with another hole on the plate to run the wires thru. That tailsection...definitely plastic haha. Velcro comes standard. Lol. I did have a problem with the connector for the plate light where the wire pulled out of the back of the connector but I just pushed the prongs back in. So im not taking it apart for the 4th time. Good vids! Thanks
Thanks so much for this great step by step walkthrough bro. I have a couple of weeks before I order this but having this guide will be tremendously helpful once I start the install. You rock.
I want that eliminator! I'll see if I can get my uncle to check the video out since you've got a good, level camera angle. He's the Chief of Police in Hutto, Texas who's a great guy. It's only 30 miles from The Circuit of the America's track, so you know he's going to be seeing the eliminator kits. Irregardless of what anyone cares about jurisdictions, It's so clean of of an eliminator that you know thousands will buy the kit and at least having one Chief sign off on it would be a great start...
That is not a bad idea. IMO as long as the plate is visible and well lit (like the New Rage here) it should be good to go. Is it 100% by the books legal? The answer to that is most likely no. - Van
My opinion, I think the Hotbodies undertail is a little better looking, sleeker. The Rage does have better location for the lights & license plate, further rearward, and the Rage is a little easier to install.
Hi Brian , installed TST industires flushmount front signals on the R3. The flash rate is similar to this. have just left it like that. should have also ordered the harness converter , plug & play. brother sent it AUSTIN ( USA).
I had to add an extra spacer/washer with the first frame part that uses the two factory bolts. The ones they provided were not thick enough and the frame piece was floating slightly on the collared factory bolt. I could spin the spacer with my finger.. It would have vibrated like crazy. Was an easy fix adding the extra washer, but I shouldn’t have to run to the hardware store when I spend $200 on a plug and play system. Other than that it’s very good
While it has been some time since I installed this I do not remember running into any issues. Perhaps they have changed the kit a bit since I did this install? - Van
@@sportbiketrackgear yes, it was an old video I realize that. I had the newer style with the hole in the bottom for the wires so it’s very possible they changed the spacer size. Other than that it’s an awesome kit highly recommended. I did end up coating mine with truck bedliner to give it a stronger finish against rock chips
Looks great. In Los Angeles where I am you wouldnt have much problem with that. Cops are bizy doing more crucial things. Personally I wish the left/right at the turn signals was a little more defined....kept to the corners so to speak. Looks killer though.
@Vance - I would like to see a rear lamp (brake) light with the same dimension as OEM, but with internal LED turn signals integrated. Now that would be a huge seller. It would be 100% legal in every state and clean-up the rear at the same time.
I used a smoked replacement tail light with integrated signals only smoked when bike is off so it’s legal. The light is by Xtasy. Then I used this kit for the undertail and plate and didn’t use the ugly white signals that flash too fast lol. Why would you make white signals when the look is to black out the undertail ? Durrrrr
Awesome build Van. Can't wait to see what your plan is for the suspension (you and I have a similar build) so I'd like to see what you do for the front. Great vids and bike brother. Congratulations
I am really excited about this project for sure man. This is one hell of a motorcycle in stock trim so I am going to leave the suspension and ABS alone until I feel like they are a hindrance before I make any changes there. - Van
getting a 23 1000 soon, love the setup and the light makes it look really clean, but curious, the hazards will it effect that or does it just work from the brake light? also is there a way to turn on and off the plate light unless i missed it?
This fender eliminator is separate from the brake light and there is no way to turn the license plate light on and off. IMO this is the best fender eliminator for the GSXR1000. - Van
Did the follow up video ever get uploaded? I looked but didn't see it. I'm gonna put on a pair of LED front signals , and can't imagine how fast it would blink with 4 LED's instead of just 2.
I was going between this or the yoshi. I can’t find a video on rather or not the uglyness is covered with the yoshi. I ordered both. The yoshi is here still waiting on rage cycles. I like the tucked looked better also
Man that looks AWESOME! Too bad those kits are illegal here in germany, they'd probably call a SWAT Team on me and impound my bike if they just see me sit on it. Then again it would probably look a bit stupid with our license plates (fun fact: the Motorcycle license plates are called "Kuchenblech" (baking sheet) here because...well because they're pretty huge. But at least we don't need one in the front! That would look *REAL* stupid) One thing I'd maybe change is to actually angle the license plate so it faces directly backwards. One of the things we have to do here in germany and it may sound silly but I think that's the right way to go. That it looks to me the police is going to have trouble reading the license plate and could just go about and stop you to read it, maybe give you a fix-it ticket (depending on state laws of course). I don't want to make their job harder than it already is. Also if I may add, the flashing rate of the rear indicator could not just be for looks but also mandated. (Again something we have to do here in Europe. A lot of people don't pass tech inspection because the indicator is flashing too fast when they convert to LED's, I don't know why that's a problem as long as it flashes but I don't ask too many questions)
LukeTheMentalGent not in Europe. Just in Germany. No bs like that in most places. You can put a tail tidy, remove number light, whatever and get the loudest exhaust possible and it is not a problem.
No, technically in all of europe if your bike is an EU-Model it has to accord to EU-Regulations. Which for example means that rear indicators *have* to be at least 180mm apart which is definitely not the case in this kit. In the UK as far as I know there is also a minimum indicator spacing which will make you fail the MOT as it will here in Germany, however the police will barely bat an eye or just lift their finger at you unlike here. To my knowledge Norway is even worse about this stuff than we are here in Deutschland, definitely not jealous of those guys. It's like some californians saying "Two Bros mufflers are legal here", that's just not true. It very clearly states that they are for closed course use only. Just because police doesn't care or that there aren't any serious repercussions for not following regulations doesn't make it legal at all, just feasible.
LukeTheMentalGent I live in Ireland and there isn't an MOT or anything like that. Most people ride with tiny number plates so they don't get caught by the cameras or cops. Also in UK mot the emissions aren't tested so you can put the loudest exhaust possible. Nobody checks indicator spacing. The only thing that matters is that you actually have indicators, MOT for bikes is extremely basic compared to cars. It's shit that you get punished for having some fun on your bike in Germany, but Germany isn't all of Europe.
Oh you learn to live with it (could be a lot worse right?), I don't mind having a tastefully noisy exhaust. There is a difference between a nice sound and just plain loud which many people tend to forget sadly, that's probably what got us here in the first place. And owning an '06 GSX-R, the Indicator fuss is also none of my concern. The only thing I'd want to change honestly would be the size of my license plate but that is definitely not going to happen. Then again Ireland isn't all of europe either but a lot (if not most) of the countries here in europe do have the flashrate for indicators mandated for example and that's all my original statement was about. The Isle of Man is part of europe too after all and those guys don't even have speed limits ;)
Every area is unique when it comes to enforcement for sure. Before you install something on your bike it is important you understand what it is like in your area. - Van
just something i noticed.. in the video the washers for the bracket are already installed in the video.. when you get the new rage kit its separated .. i had to learn the hard way.. not a big deal though
Is it possible to change the angle of the license plate holder to 15 degrees(so it's more visible from the back) without it interfering with the tire? In my country the rule for motorcycle license plates is 15 degrees.
Slide the wires down and thru the license plate led. No wires showing. Also this item is at least $100 overpriced. Its basic metal, cheap chinese screws and very basic paint. At best, this should cost no more than $49......yet it's going for $200.
Hard to accurately diagnose this over RUclips comments. The first thing I would try is to reverse the polarity of the led harness and see if that works. You may need to reach out to New Rage and ask for support. They will be in the best position to help you get this sorted out. - Van
Outstanding tutorial !! Just picked up a '21 and did/doing the install today of this and after everything is buttoned up, I'm seeing a substantial gap between that plate and the fairing. Enough to actually see that dog bone bracket and some wires (since I ran wiring through the hole in the bracket and not around the side like he did). I have the washers installed on the bracket (bracket>washer>frame) and the bolts tightened down, double checked all other bolts, placement of everything, and I can't see why I'm getting such a gap. Has anyone else seen this?
Thanks for watching. It has been quite some time since I did this install and the bike is now track only. Sorry but I do not have any valuable input here. - Van
I am not sure we got that done but can tell you if you install the Driven Flasher Relay it will sort that out for you. Here is a link to that on our site: www.sportbiketrackgear.com/driven-flasher-relay/
That looks amazing van. Can you do a video on installing lowering links I saw you sell them for a FZ01 and am very Interested to see how they work. Thanks.
There are slots on the bracket to allow for different sized plates. Really depends on the spacing of your bolts. Measure the distance between the bolts from one side to the other post that here. I will measure the eliminator to see what the range it will offer is. - Brian Van
I put on the fender eliminator but also have the smoked integrated taillight,does anyone know how can put both signal lights to work for license plate and integrated taillight?
@@sportbiketrackgear thanks Brian.. I purchased the hot bodies undertail from you. Still awaiting delivery but you have shipped it. I have seen other install videos on it but not as detailed as the videos you do. Shout out to Josh for keeping me up to date when ever I sent a query through...
No I do not think you would be able to get this installed on your bike, the 2 models are pretty different. Here is a link to the fender elim New Rage offers for your bike: www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r750-11-17-fender-eliminator/ New Rage Cycles Suzuki GSX-R750 06-19 Mirror Eliminators w/ LED Turn Signals www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r750-06-17-mirror-eliminators-w-led-turn-signals/
Yes you can install a different flasher or the New Rage Cycles resistors. Below are links to both products on our site: Driven Flasher Relay www.sportbiketrackgear.com/driven-flasher-relay/ New Rage Cycles Dual-Load Equalizer www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/
It will still flash, if the flash rate is too fast you can install a resistor. Here is a link to the resistors on our site: www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/
I am runnning Stompgrip on the GSXR1000R. Here is a link to it on our site: www.sportbiketrackgear.com/stompgrip-suzuki-gsx-r1000-2017-traction-pad-tank-kit/ - Van
Help :( :( I just installed mine on my 2018 GSXR 1000r and everything works expect the license plate light :(...... turn signals work great, brake light works but the license plate light doesn’t turn on and it’s plugged in correctly too :( help help help please
No this will not fit the 750. Here is a link to the New Rage Cycles Suzuki GSX-R750 11-19 Fender Eliminator on our site: www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r750-11-17-fender-eliminator/
@@sportbiketrackgear I already have the Hotbodies one, Blue to match the bike, but I have the same smoked Integrated Brake Light with Turn signals, I wired the Hot Bodies LED's and also got a Signal Flasher Relay so I got the Hyper Flash under control, I HATED THAT!!!! Flash so fast as to be a steady Light, Anyway, point is the Hotbodies signals and the signals from the Brake Light work together and look really good. Thank You BV as I bought the HB Undertail from you.
I own STG, New Rage is one of the product lines we offer on the site and I have no involvement beyond being a dealer for the products. Personally I dig this kit, we have others on the site if this one is not your style. That said New Rage fender elimns have been selling very well since we added them to the site a couple months back. - Van
Am I the only one that's blown away by the price. An LED light, a few pieces of stamp steel that have been painted and a couple screws for $200. And the LED turn signals are really not that attractive. Should have been a smoke lens on them or something. Sticks out like a sore thumb.
IMO this is a fair price for the kit when you consider the development time it takes to get the kit ready to manufacturer etc... New Rage uses OEM style connectors with quality harness construction on their kits. In just 3 months New Rage Fender Eliminators are one of the best sellers we offer for more than one model bike. Some people like chocolate while others prefer vanilla my brother. - Van
That 3rd hole in the tail cover is for the wires to route through then up and though the tail section to the connection points. Then I used the factory zip tie to snug everything together. Came out very clean. Thanks for the video.
Actually I see that the cover in this video does not have that wire hole that mines came with. I must have a newer version. Just ordered recently.
Sometimes the manufacturer will make small updates to the parts after we have shot the install videos. Thanks for watching and sharing your feedback! - Van
Just installed this kit on my 18 GSXR 1000. This video was extremely helpful and made my install quick and easy. Thanks for sharing!!!!
last week I received my GSXR1000R 2022 Grea colour, earlier I ordered an NCR plate from STG and I have received it last 2 months hopefully I will install it these days, Thanks for the awesome video and your explanation was super clear.
Enjoy your new bike! Thank you for the order and for watching! - Van
Ok very instructional video I was completely baked last Sunday doing this job to my 2020 1000R however.. you did not not that the supplied washers given once tightened all the way down still spin and therefore would rattle. I ended up adding one more to each side but this could have been cured with a slightly thicker washer but they missed that or didn’t care. Still a good kit and thanks for the video !
Every bike is a little different so sometimes you need to get creative to get the result you need. - Van
I had the same issue. If you watch the video they are loose in this too. It would vibrate like crazy. 200$ for a plug and play kit and I had to go to home depot for washers.
Just followed this step by step install video you put for the Gsxr1000R. Super easy and glad i went with this set up. Ordered from Joe, thanks Brian for doing a kick ass job putting this together!
Thank you for the business! Happy to hear you found this video helpful in getting your project done! - Van
First time STG customer and this video was great. Look forward to many more mods with the STG. Crew. Thanks!
Thank you for your business and the kind words! - Van
Running light has better perception. But the Product is perfect 😍
Just installed the kit. Video was perfect! Love the new look. Thanx!
You're welcome, happy to help out! - Van
I just got my fender eliminator today. Going to be installing it tomorrow. Very helpful video.
Thanks for the vids!! Made that look easy. The kits updated with another hole on the plate to run the wires thru. That tailsection...definitely plastic haha. Velcro comes standard. Lol. I did have a problem with the connector for the plate light where the wire pulled out of the back of the connector but I just pushed the prongs back in. So im not taking it apart for the 4th time. Good vids! Thanks
You are welcome and thanks for watching! - Van
Thanks so much for this great step by step walkthrough bro. I have a couple of weeks before I order this but having this guide will be tremendously helpful once I start the install. You rock.
You are welcome, happy to help out. - Van
I want that eliminator!
I'll see if I can get my uncle to check the video out since you've got a good, level camera angle. He's the Chief of Police in Hutto, Texas who's a great guy. It's only 30 miles from The Circuit of the America's track, so you know he's going to be seeing the eliminator kits. Irregardless of what anyone cares about jurisdictions, It's so clean of of an eliminator that you know thousands will buy the kit and at least having one Chief sign off on it would be a great start...
That is not a bad idea. IMO as long as the plate is visible and well lit (like the New Rage here) it should be good to go. Is it 100% by the books legal? The answer to that is most likely no. - Van
That's a great kit....
I like how it's a detailed video....
What's better is the SLICKS ....
This fender elim looks awesome on the GSXR for sure. - Van
My opinion, I think the Hotbodies undertail is a little better looking, sleeker. The Rage does have better location for the lights & license plate, further rearward, and the Rage is a little easier to install.
thanks a lot this was super helpful , but you said you'll talk about the fast signal lights but I did not see the video that talks about it ..
Install this relay: www.sportbiketrackgear.com/driven-flasher-relay/
Hi Brian ,
installed TST industires flushmount front signals on the R3. The flash rate is similar to this.
have just left it like that. should have also ordered the harness converter , plug & play. brother sent it AUSTIN ( USA).
I had to add an extra spacer/washer with the first frame part that uses the two factory bolts. The ones they provided were not thick enough and the frame piece was floating slightly on the collared factory bolt. I could spin the spacer with my finger.. It would have vibrated like crazy. Was an easy fix adding the extra washer, but I shouldn’t have to run to the hardware store when I spend $200 on a plug and play system. Other than that it’s very good
While it has been some time since I installed this I do not remember running into any issues. Perhaps they have changed the kit a bit since I did this install? - Van
@@sportbiketrackgear yes, it was an old video I realize that. I had the newer style with the hole in the bottom for the wires so it’s very possible they changed the spacer size. Other than that it’s an awesome kit highly recommended. I did end up coating mine with truck bedliner to give it a stronger finish against rock chips
Thank you for the video, about to tackle this right now.
Looks great. In Los Angeles where I am you wouldnt have much problem with that. Cops are bizy doing more crucial things. Personally I wish the left/right at the turn signals was a little more defined....kept to the corners so to speak. Looks killer though.
Thanks for watching and sharing the feedback. I agree this fender elim looks great, one of our best sellers. - Van
@Vance - I would like to see a rear lamp (brake) light with the same dimension as OEM, but with internal LED turn signals integrated. Now that would be a huge seller. It would be 100% legal in every state and clean-up the rear at the same time.
I used a smoked replacement tail light with integrated signals only smoked when bike is off so it’s legal. The light is by Xtasy. Then I used this kit for the undertail and plate and didn’t use the ugly white signals that flash too fast lol. Why would you make white signals when the look is to black out the undertail ? Durrrrr
This is actually badass. Tbh wished suzuki would integrate the front signals in the mirrors would make this look even more SICK.
Awesome build Van. Can't wait to see what your plan is for the suspension (you and I have a similar build) so I'd like to see what you do for the front.
Great vids and bike brother. Congratulations
I am really excited about this project for sure man. This is one hell of a motorcycle in stock trim so I am going to leave the suspension and ABS alone until I feel like they are a hindrance before I make any changes there. - Van
👏🏼👏🏼👏🏼👏🏼 wow. How clean and your video made was 💯😎😎😎
Ok so I said fuck it and did it all myself and man do I feel good about it. This video and others from u helped me out a lot thanks
Happy to hear the video was helpful! - Van
getting a 23 1000 soon, love the setup and the light makes it look really clean, but curious, the hazards will it effect that or does it just work from the brake light? also is there a way to turn on and off the plate light unless i missed it?
This fender eliminator is separate from the brake light and there is no way to turn the license plate light on and off. IMO this is the best fender eliminator for the GSXR1000. - Van
Such a great video saved me $150
Happy to hear it was helpful. - Van
I mean you can always bend the plate half an inch and it’ll be totally visible. Not a hard fix and keep a nice kit
I was thinking same
Did the follow up video ever get uploaded? I looked but didn't see it. I'm gonna put on a pair of LED front signals , and can't imagine how fast it would blink with 4 LED's instead of just 2.
Great tutorial, very helpful 👍
You are welcome and thank you for watching! - Van
I was going between this or the yoshi. I can’t find a video on rather or not the uglyness is covered with the yoshi. I ordered both. The yoshi is here still waiting on rage cycles. I like the tucked looked better also
I really liked the way the Rage looked on this bike myself. - Van
Man that looks AWESOME! Too bad those kits are illegal here in germany, they'd probably call a SWAT Team on me and impound my bike if they just see me sit on it. Then again it would probably look a bit stupid with our license plates (fun fact: the Motorcycle license plates are called "Kuchenblech" (baking sheet) here because...well because they're pretty huge. But at least we don't need one in the front! That would look *REAL* stupid)
One thing I'd maybe change is to actually angle the license plate so it faces directly backwards. One of the things we have to do here in germany and it may sound silly but I think that's the right way to go. That it looks to me the police is going to have trouble reading the license plate and could just go about and stop you to read it, maybe give you a fix-it ticket (depending on state laws of course). I don't want to make their job harder than it already is.
Also if I may add, the flashing rate of the rear indicator could not just be for looks but also mandated. (Again something we have to do here in Europe. A lot of people don't pass tech inspection because the indicator is flashing too fast when they convert to LED's, I don't know why that's a problem as long as it flashes but I don't ask too many questions)
LukeTheMentalGent das Nummernschild ist schon der Hammer 🔨
LukeTheMentalGent not in Europe. Just in Germany. No bs like that in most places. You can put a tail tidy, remove number light, whatever and get the loudest exhaust possible and it is not a problem.
No, technically in all of europe if your bike is an EU-Model it has to accord to EU-Regulations. Which for example means that rear indicators *have* to be at least 180mm apart which is definitely not the case in this kit.
In the UK as far as I know there is also a minimum indicator spacing which will make you fail the MOT as it will here in Germany, however the police will barely bat an eye or just lift their finger at you unlike here.
To my knowledge Norway is even worse about this stuff than we are here in Deutschland, definitely not jealous of those guys.
It's like some californians saying "Two Bros mufflers are legal here", that's just not true. It very clearly states that they are for closed course use only. Just because police doesn't care or that there aren't any serious repercussions for not following regulations doesn't make it legal at all, just feasible.
LukeTheMentalGent I live in Ireland and there isn't an MOT or anything like that. Most people ride with tiny number plates so they don't get caught by the cameras or cops. Also in UK mot the emissions aren't tested so you can put the loudest exhaust possible. Nobody checks indicator spacing. The only thing that matters is that you actually have indicators, MOT for bikes is extremely basic compared to cars. It's shit that you get punished for having some fun on your bike in Germany, but Germany isn't all of Europe.
Oh you learn to live with it (could be a lot worse right?), I don't mind having a tastefully noisy exhaust. There is a difference between a nice sound and just plain loud which many people tend to forget sadly, that's probably what got us here in the first place. And owning an '06 GSX-R, the Indicator fuss is also none of my concern. The only thing I'd want to change honestly would be the size of my license plate but that is definitely not going to happen.
Then again Ireland isn't all of europe either but a lot (if not most) of the countries here in europe do have the flashrate for indicators mandated for example and that's all my original statement was about. The Isle of Man is part of europe too after all and those guys don't even have speed limits ;)
Yup yep , try ussing that shit down here in South Fl . Lmao good luck
Every area is unique when it comes to enforcement for sure. Before you install something on your bike it is important you understand what it is like in your area. - Van
Going to buy one
just something i noticed.. in the video the washers for the bracket are already installed in the video.. when you get the new rage kit its separated .. i had to learn the hard way.. not a big deal though
Lol so did I. I just stalled on my 2020 and was like “duh! You dufus” lol
Legends say you have a discount code for me 😂
Shoot an email to Cody@sportbiketrackgear.com and he will get you sorted out. - Van
Is it possible to change the angle of the license plate holder to 15 degrees(so it's more visible from the back) without it interfering with the tire? In my country the rule for motorcycle license plates is 15 degrees.
You could try and bend the bracket a little but I do not feel like it would move very much. - Van
Slide the wires down and thru the license plate led. No wires showing. Also this item is at least $100 overpriced. Its basic metal, cheap chinese screws and very basic paint. At best, this should cost no more than $49......yet it's going for $200.
Possible to have an installation video for Kawasaki Z900? Would be of great help!!
Sorry we do not have a Z900 project bike here at STG. - Van
The turn signal blinks faster when this device is mounted. What kind of power resistor do you need to use?
New Rage Cycles Dual-Load Equalizer
www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/ - Van
I can see the link, but I do not see the power value of this resistor ??
I need help I have a 21 gsxr 100r once I plug in the leds none of them work. I plug in oem and they work fine. Any help on this?
Hard to accurately diagnose this over RUclips comments. The first thing I would try is to reverse the polarity of the led harness and see if that works. You may need to reach out to New Rage and ask for support. They will be in the best position to help you get this sorted out. - Van
Outstanding tutorial !!
Just picked up a '21 and did/doing the install today of this and after everything is buttoned up, I'm seeing a substantial gap between that plate and the fairing. Enough to actually see that dog bone bracket and some wires (since I ran wiring through the hole in the bracket and not around the side like he did). I have the washers installed on the bracket (bracket>washer>frame) and the bolts tightened down, double checked all other bolts, placement of everything, and I can't see why I'm getting such a gap. Has anyone else seen this?
Thanks for watching. It has been quite some time since I did this install and the bike is now track only. Sorry but I do not have any valuable input here. - Van
I’m having the same issue on my 22 did you end up figuring it out?
@@johndapper8751 Nope. 😵💫 I decided to just let it not bug me as much.
@@00seanzy i think that’s what I’m gonna do I spent all day doing it over and over again and still the same lol , appreciate the reply bro
How do you get the aftermarket blinker to not blink so fast?
New Rage Cycles Dual-Load Equalizer (you need these as well)
www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/
Where I can the video that i let the signals flashing normally not in a quick way , please provide it with me
I am not sure we got that done but can tell you if you install the Driven Flasher Relay it will sort that out for you. Here is a link to that on our site: www.sportbiketrackgear.com/driven-flasher-relay/
What size number plate fit these ? Mine comes tomorrow need to get a new plate ordered 😀
This is designed to work with a standard motorcycle plate. - Van
HI ,
u beauty. .neatly done.
That looks amazing van. Can you do a video on installing lowering links I saw you sell them for a FZ01 and am very Interested to see how they work. Thanks.
We have a Vortex lowering link on the way now for the Ninja 400 STG Project Bike. Should have a video in the next couple weeks. - Brian Van
Sportbike Track Gear perfect looking foward to that. Thanks a lot.
These fender eliminators are designed for the standard US plates (7x4 inches), right? So would it also fit a 7x5?
There are slots on the bracket to allow for different sized plates. Really depends on the spacing of your bolts. Measure the distance between the bolts from one side to the other post that here. I will measure the eliminator to see what the range it will offer is. - Brian Van
I put on the fender eliminator but also have the smoked integrated taillight,does anyone know how can put both signal lights to work for license plate and integrated taillight?
Assuming your tail light has the turn signals built in you will need to wire the turn signals to the fender elim and the taillight. - Van
have you done a similar video with the hotbodies undertail for this bike?
Sorry we did not shoot an install for that undertail on this bike. - Van
@@sportbiketrackgear thanks Brian.. I purchased the hot bodies undertail from you. Still awaiting delivery but you have shipped it. I have seen other install videos on it but not as detailed as the videos you do. Shout out to Josh for keeping me up to date when ever I sent a query through...
Can you put a 2016 gsxr 1000 tail fairing on a 2017 gsxr 1000?
Is it the same way to install on a 2019 GSXR 750? Like I can get it for mine and follow these instructions?
No I do not think you would be able to get this installed on your bike, the 2 models are pretty different. Here is a link to the fender elim New Rage offers for your bike: www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r750-11-17-fender-eliminator/
New Rage Cycles Suzuki GSX-R750 06-19 Mirror Eliminators w/ LED Turn Signals
www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r750-06-17-mirror-eliminators-w-led-turn-signals/
What is the brand of the T-handle socket wrench with the blue grip?
Motion Pro Spinner II T-Handle Here is a link to it on our site: www.sportbiketrackgear.com/motion-pro-spinner-ii-t-handle-3-8-08-0562/ - Van
@@sportbiketrackgear appreciate it 👍🏽
@
Sportbike Track Gear....What was that T-shaped tool you were using dog?
Did you ever slow down the turn signal?
Yes you can install a different flasher or the New Rage Cycles resistors. Below are links to both products on our site:
Driven Flasher Relay
www.sportbiketrackgear.com/driven-flasher-relay/
New Rage Cycles Dual-Load Equalizer
www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/
Something for Suzuki gsx s1000 2020 ?
Sorry they are not producing any kits for the GSX-S models. - Van
Sweet
You think this would fit on 2018 GSX-S 1000?
No that is a completely different model. - Van
How do you stop the flashing? Couldn’t find anything online
New Rage Cycles Dual-Load Equalizer
www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/
How much power should you buy a resistor?
Hello, what is the name of this fixture and where can I buy it?
New Rage Cycles Suzuki GSX-R1000 17-21 Fender Eliminator
www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r1000-2017-fender-eliminator/
If i run an LED swap on the front will still flash ?
It will still flash, if the flash rate is too fast you can install a resistor. Here is a link to the resistors on our site: www.sportbiketrackgear.com/new-rage-cycles-dual-load-equalizer/
Will this work for 2022 gsxr 1000r?
Yes this model is largely unchanged. - Van
Amazing job where your shop at ?
We are located at 56844 Mound Road Shelby MI 48316. Open Monday through Friday from 10 am to 6 pm. - Van
What tank grips did you use?
I am runnning Stompgrip on the GSXR1000R. Here is a link to it on our site: www.sportbiketrackgear.com/stompgrip-suzuki-gsx-r1000-2017-traction-pad-tank-kit/ - Van
Help :( :( I just installed mine on my 2018 GSXR 1000r and everything works expect the license plate light :(...... turn signals work great, brake light works but the license plate light doesn’t turn on and it’s plugged in correctly too :( help help help please
Can you guys get the hindle megaphone exhuast for the ninja 400? Thanks
Shot the slip on today and will do the full system tomorrow. - Van
Sportbike Track Gear when will you launch the exhuast on your website? As well as post the video asap!!! Thanks
Sportbike Track Gear when will you release the hindle wanna buy it today?
Please email jimmy@sportbiketrackgear.com and he will get you all dialed in man. We will get you one of the very first systems in the US. - Van
Where can I buy this Fender Eliminator?
New Rage Cycles Suzuki GSX-R1000 17-21 Fender Eliminator
www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r1000-2017-fender-eliminator/
You're either ungodly strong, or I'm just weak. That well nut took longer to get in then the length of this video.
Does this work with a 2017 GSXR 750?
No this will not fit the 750. Here is a link to the New Rage Cycles Suzuki GSX-R750 11-19 Fender Eliminator on our site: www.sportbiketrackgear.com/new-rage-cycles-suzuki-gsx-r750-11-17-fender-eliminator/
I just ordered mine today, I have a smoke integrated tail light with turn signals already.can I install this without the turn signals ?
Thanks
Yes you do not have to install the signals if you prefer not to. - Van
@@sportbiketrackgear I already have the Hotbodies one, Blue to match the bike, but I have the same smoked Integrated Brake Light with Turn signals, I wired the Hot Bodies LED's and also got a Signal Flasher Relay so I got the Hyper Flash under control, I HATED THAT!!!! Flash so fast as to be a steady Light, Anyway, point is the Hotbodies signals and the signals from the Brake Light work together and look really good. Thank You BV as I bought the HB Undertail from you.
I know New Rage is your company, but c'mon, you happy with this? I'm lookin' to get noticed by everyone, even the stars.
2:13 answered-ish. but we can be the 1.1%ers.
I own STG, New Rage is one of the product lines we offer on the site and I have no involvement beyond being a dealer for the products. Personally I dig this kit, we have others on the site if this one is not your style. That said New Rage fender elimns have been selling very well since we added them to the site a couple months back. - Van
Am I the only one that's blown away by the price. An LED light, a few pieces of stamp steel that have been painted and a couple screws for $200. And the LED turn signals are really not that attractive. Should have been a smoke lens on them or something. Sticks out like a sore thumb.
IMO this is a fair price for the kit when you consider the development time it takes to get the kit ready to manufacturer etc... New Rage uses OEM style connectors with quality harness construction on their kits. In just 3 months New Rage Fender Eliminators are one of the best sellers we offer for more than one model bike. Some people like chocolate while others prefer vanilla my brother. - Van
Not an 18-
What a great way to look like a trouble maker......
If you do not like the look of this kit there are tons of other options for this model. - Van