Nice one brother... Carbonisation of the electrodes and rectification probes is very common. The state of the electrodes gives a good insight into if the burner mix is too high or too low.. Burnt or melted probes can mean too high carbon ratio or heavy coating to little. Correct set up of the gas/air ratio very important to correct operation.
Thanks for uploading! I had same exact symptoms. Allowed me to narrow down cause. I cleaned the probe but issue persisted. Ended up being the contacts on the other end of the cable needed cleaned. Contacts calcified from a prior leak.
Been missing your videos mate. Hopefully your back soon. Always seems to happen. Engineers go in a different direction or just stop filming. More importantly, hope everything's good with you 🎉
I had E133 yesterday, it turned out to be a split condense pipe leaking onto the flame rectification plastic joint and cutting it out. It was the original grey flexible one, replaced to black hose.
Litrally have the same leaking boiler and have not had heating or hot water since 5 15 on 16th Dec.. should be fixed oin next 24 hours but exactly same issue it's leaking and putting the pilot light out
I’m really sorry I don’t anymore I’m a bit too far away, Sounds to me like the gas may not be getting to the boiler or needs to be purged Please call a local gas safe engineer to repair or rectify this Thanks for watching
Guys got a eco compact 30 hot water runs fine but no heating.rads and water symbols shown but no flame when demanding heating.The red and green lights are flashing on receiver cant solve?i have turn the hot water dial 90 degrees twice it fires up with flame symbol then heats up then flame goes out do it a couple of times then i get flashing error 133 flame crossed out and an R top right above error number. i have blaming my receiver and thermostat no connecting does that narrow it down ?its getting cold. regards
![[ GUILTY GEAR STRIVE: DUAL RULERS ] Teaser Trailer](http://i.ytimg.com/vi/e4TDqaE3XAg/mqdefault.jpg)
Thank you, good explanation
Thank you for being clear with explaining most just go on and don't get to the point ...but you are clear with helping us engineers .
Haha cheers, love to chat, what can I say 😂
Nice one brother...
Carbonisation of the electrodes and rectification probes is very common.
The state of the electrodes gives a good insight into if the burner mix is too high or too low..
Burnt or melted probes can mean too high carbon ratio or heavy coating to little.
Correct set up of the gas/air ratio very important to correct operation.
Thanks for the info mate this is what comments sections are for
Thanks for uploading! I had same exact symptoms. Allowed me to narrow down cause. I cleaned the probe but issue persisted. Ended up being the contacts on the other end of the cable needed cleaned. Contacts calcified from a prior leak.
Lovely!
Well done mate Good presentation and valuable tip!
Thank you mate!
Some good hints and tips there mate. Appreciate you sharing..
No problem hope it helps
Great stuff pal, I generaly use a file to clean spark and rectification electrodes. Works better then wire wool or sandpaper. 👍
Great work mate keep it coming,
Will do mate thank you
Been missing your videos mate. Hopefully your back soon. Always seems to happen. Engineers go in a different direction or just stop filming.
More importantly, hope everything's good with you 🎉
Thanks mate, had lots of family issues to resolve
Then got married and all sorts haha
Cheers for the support craig
I had E133 yesterday, it turned out to be a split condense pipe leaking onto the flame rectification plastic joint and cutting it out. It was the original grey flexible one, replaced to black hose.
Yep that’s common on these too
Litrally have the same leaking boiler and have not had heating or hot water since 5 15 on 16th Dec.. should be fixed oin next 24 hours but exactly same issue it's leaking and putting the pilot light out
Cheers, going out to one of these tomorrow.
Hope it helps
Thanks for video
Nice one
No problem mate! Hope it helps
I have this E133 after installing a new PCB installed from a E168 caused by installing a new smart meter. Do you cover Romford?
I’m really sorry I don’t anymore I’m a bit too far away,
Sounds to me like the gas may not be getting to the boiler or needs to be purged
Please call a local gas safe engineer to repair or rectify this
Thanks for watching
Had a strange one on a same type of baxi can’t always believe the code faulty rf room stat causing same code which doesn’t make any sense
That’s unusual never would of thought that
Guys got a eco compact 30 hot water runs fine but no heating.rads and water symbols shown but no flame when demanding heating.The red and green lights are flashing on receiver cant solve?i have turn the hot water dial 90 degrees twice it fires up with flame symbol then heats up then flame goes out do it a couple of times then i get flashing error 133 flame crossed out and an R top right above error number. i have blaming my receiver and thermostat no connecting does that narrow it down ?its getting cold. regards
Please contact a gas safe engineer to solve this issue
Thanks
How much full service of boiler if I contacted u how can do
£75 but depends on where you are mate
What if it don’t reset?
Call a gas safe engineer please
@@snapgas9832 no
Quoted 350+ for repair 133 error and cover ground worker mate came around and disconnected thermostat on wall works now overpriced over complicated 😂
👌 ok