Dodge won’t go into Overdrive Fixed
HTML-код
- Опубликовано: 19 июн 2020
- Dodge Avenger won’t go into overdrive fix. How to save your Dodge Avenger front wheel drive transmission. Change speed Sensors. If I helped you cashapp me $1 @ $mdmurphy73. Social Experiment for my kids.
Хобби
I have this same exact problem, was gonna go buy a $250 throttle body but was hoping I could find a cheaper solution. Gonna change mine Wednesday and see if it helps! Thanks man!!
Thanks so much for this video. My 2008 dodge avenger had this same issue. I found both sensors at rockauto online and only paid about $12 for both. It only took about 15 minutes to replace and seems to have fixed the problem for me as well. Note: my output sensor wasnt burnt up like yours It was actually covered with metal fillings which I can only assume was preventing the computer from getting a good signal. Time to change the tangy fluid and hope this car lasts a little longer since the engine and transmission are still running great 152,000 on the odm. Thanks again
You’re welcome. Yes I would definitely change fluid and filter. Check pan for metal shavings. Also use dodge recommended fluid. Don’t go with anything else. It will damage transmission.
planning on buying a Dodge Calipher with simular issue and will try this and post results.
Great video. Just FYI, that's not a burn out on the output sensor. Since they're magnetic, that's all the engine metal flakes it's picked up out of the oil, which then messes with the sensor's capability to sense your speed, which is the primary one that causes the vehicle not to shift gears. Many think the RPM's controls shifting, but the output sensor is the most important within that medley of sensor analysis when it comes to shifting to the next gear in an automatic transmission.
Thank you, Awesome video!!!
Mine had build up on it, cleaned it works good
Great vid, and very useful. Thanks buddy.
Your welcome
Was this problem intermittent before it went out completely? I am having pretty much the same trouble, but mine sets the P06DD (low oil pressure code) every time it happens. I can get it to shift into 6th gear if I turn the engine off while the van is rolling, put the transmission in neutral, then start the engine again while still rolling down the highway and it will then shift into 6th gear again. It does this when it's cold outside and when I am towing a heavy load.
The output sensor costs more than the input sensor because it's the one that goes out the most.
After the replacement be sure to reset Computer. I do this by disconnect negative cable to battery for 30 min.
Good to know. The issue still persists. Its random thou. I can drive 20 miles without an issue then start the car again and have these symptoms. Traction control light comes on and it wont shift into 4th gear. Also randomly the red security light will come on with the tpms light. All tire pressures are good. Recently had one of the Tire pressure monitors replaced.
I have a 2010 Dodge Journey does not change 4th gear and feels slow jerks sometimes
Try the throttle body
Nice video, did you get an error code for this problem? Do you have the 62te transmission?
Didn’t check codes. Not sure on transmission.
Hi there,
I have same problem with my Dodge Ram 3500 2016. Would my truck would have same speed sensor?
Definately has a speed sensor. Maybe not in same location though.
Round white sensor on side .
Just fix this problem in a 03 Dodge Dakota. Disconnect the harness underneath driver side and plug it back in everything went back to normal
Power steering Noir overdrive wasn't working after unplugging harness and plugging it back in everything went back to normal
Bad connection in harness. Hopefully no corrosion from moisture in plug.
2009 charger 2.7 v6
What’s that light under the D
Low tire pressure.
That's the same issues I'm having
Clean out put speed sensor?
Yes!
I'm going to try this next...
That may help
@@Mr.Nobody423 did your check engine light come on or did you check for any codes with a computer device?
Check engine light stayed on the whole time I had car. No I didn’t have codes checked.
@@Mr.Nobody423 ik.mine isnt throwing codes and the check engine light is not on...I think that that new pcm they out in needs to be flashed or calibrated.
I'm going to have then reflash my new pcm...maybe that'll work.
Thanks
You’re welcome please please subscribe
I have a question my 2010 Dodge Avenger is giving me codes po700 and po755 and it's telling me transmission sensor is this the same thing because my car is doing the same thing
@waylonsmothers6436 yes those a general transmission codes. Don’t really point to the problem sensor.
I replaced both on My avenger and still got issues
Where was the output sensor located??
Under the air filter and above transmission fluid pan drivers side.
it was on the passenger side on my Dodge ram 1500 , 07. but yes underneath the air filter box
You won't happen to have the part numbers for the parts..
No idea