I saw this project on instructables by system X. I tried to solder the components on a perforated circuit board but I couldn't get the solder to flow the way I wanted it too. Your PCB design helped me to complete this project. I couldn't have done it without your PCB design. Greetings from USA.
I love this video. I am looking to have 36 machines send a signal back to my office telling me what state of operation they are in. Using multi color LED's to tell me the different states. I think this video might get me in the right direction.
Could you explain what you changed in the code, I'm making one myself but when I went to implement the code in my arduino, I realized I didn't know which parts to change the code
brother accidently i have switched the anode and shot all of them that means i switch the row and column opposite as you said what will i do now help me
I solder 8x8 Dot Matrix. I use Anode as Column and Cathode as row. I use 2 of 74HC595. I connect each row directly to 74HC595. Now I'm able to display text but it's flickering. I was told to use 8 of BC547 transistor for each row. Do they fix the flickering problem?
You run a high frame rate and dither. I Wonder if it is possible to put a latch after the shift registers. Then per row you can load new versions of this row where more and more LEDs go dark. Then clock the latch ( without the latch would worry about EMI ). Shift registers are fast. You can probably do 8bit at this low resolution.
Hi,Nematics,i am doing this same project but on the row,i used 74hc595,and it 8*40, All things work right but the problem is i can not print out the numbers or some symbols like question mark on exclamation,can you please help me how to modify the codes so that i get the wanted result,
is there need any darlngton trasitor or mosfet to give sufficient current to the leds?or not need bro?and can be it done with aurduino nano?then can u share the pic diagram?
As mentioned previously my strength is in electronics not Arduino software. I do not know which lines of code effect the addition of another 24 columns. Can you give some assistance?...thanks
what are the different led matrices sizes (m*n) we can construct for an led display ., and by the way bro name of the pen you used for explanation in this video...????
Are you multiplexing each row ie 24 led? If so,then how are you powering it as then the maximum forward voltage is greater than 45 volts and you are only using a 5 volt? Please explain as i am only a beginner in arduino. Thank you.
Hey friend can you help me to make digital clock problem is only power supply, 1) First I purchased 2.5 inches(approximate) 7 segment display but it requires 9V for each segment and I was not able to use high side transistor switch, so I made my own segment display with 2 led for each segment and total of 2*7*4=56 LEDs, and they also not glowing as expected, now I'm working on 3rd experiment on bread board with total of 28 LEDs, one LED for each segment. So nearest 7 segment works with maximum brightness and decreases with distance, thanks in advance
Hi, I'm trying a simple version of this with 4 leds and I'm probably missing something. How am I supposed to light only the diagonal leds? According to connections shown, I can't understand how it's possible not to light all of them but pick just the diagonals...
Finally, someone explains electronics instead of simply putting BG music. Thx!
I saw this project on instructables by system X. I tried to solder the components on a perforated circuit board but I couldn't get the solder to flow the way I wanted it too. Your PCB design helped me to complete this project. I couldn't have done it without your PCB design. Greetings from USA.
Am amazed to see such vedios from Indian RUclipss and obviously a tech Frick ... Keep up up the good works man.. lots of good wishes
Thanks
freak* 😐
Wtf is frick? Also, “vedios”?
Wow you gave credit to the project creators 😅 this is very proper and more people need to do this yur awesome mate 🎉
Congratulations!
Excelent Work!
Really nice work. Thank you for uploading the video. I also plan to build my own LED matrix. I will use this as a reference.
Thank you very much, because I finally understood this from your video.🙂 🙂 🙂
Next up on Nematics Lab - I made a 1920×1080 wall sized display because I had a few LEDs lying around and didn't knew what to do.
Absolute Mad Lad
That would require almost 2 MILLION LEDS!
It would be:
- inefficient
- expensive as hell
- take days to solder
@@iProgramInCpp Sarcasm bud :)
@@iProgramInCppbut this is how these walls work. We just need to build a robot to do the job. LEDs from tape.
its awesome! 😍🔥
Thanks 😁
A great shit from Greatscott!! 😂... just kidding!! Great and carry on!!
Suspiciously looks like a GreatScott channel, but with desi accent.
the schematics are not that accurate
:D
I love this video. I am looking to have 36 machines send a signal back to my office telling me what state of operation they are in. Using multi color LED's to tell me the different states. I think this video might get me in the right direction.
Love From Bangladesh 🇧🇩
I think that this chanel is new version of GREAT SCOTT!
Haha same
instead of soldering the LEDs like that, won't another custom-designed PCB work? or perhaps another 2 layers to the existing PCB?
Great Scott video style
Very nice vid bro! keep it up!
Thank u(always wanted to make Kerfuś cosplay)
Excellent project
Awesome bro..learned new things..that's what i expect from a tuber...keep it up..just great...
Interesting! Can you explain why you used a 4017 for rows rather than a fourth 74HC595?
i was wondering this too.
Beacuse 4017 is a decade counter but 74hc595 is a shift register....❤️❤️❤️
what should be change in code for 6*32 led matrix
You need to add 2 more shift registers in circuit and change for loop in code
@@Nematics_Lab will it display small case letter like a,b,c,
@@Nematics_Lab what and where should be change in code please?
i have to change just 24 to 32 everywhere in the code?
@@MasterTv_777I understand why electronics is hard, but why can no one code??
I made this,, it works like a charm, thanks for this...
But I have a question , I can't print more than 8 letters, please help
regester ohm plz
220ohm
Indian great Scott, thanks. I sure you are the best Indian great Scott.
I want to build one of these but using 2 color or bi-colored led's . Tks.
Please tell me the values of resistances
220 ohm
You made the driver pcb using JLCPCB, but why you did not make the led matrix using JLCPCB too?
pretty good video but looks like the narration, explaining and sponcer is inspired by great scott
That's true
Yes
Yap!,..it's .almost copy everything from great Scott...from intro, to explanation, and also for searching circuit boards. Can't deny that way
Could you explain what you changed in the code, I'm making one myself but when I went to implement the code in my arduino, I realized I didn't know which parts to change the code
I think you could show the diagram for those who are not fast learners. it was an awesome video
There is a link in description
From where did you bought silver copper wire
You can find them on amazon, but I bought it from local store
@@Nematics_Lab thanks ♥️
Sir, if I want more than 6 row in it then what should I do and which ic I need for it
Nice. Good job. Now you can add a bluetooth system and, from de phone, you should send the text to your arduino.
There is one led witch is not working i think....
Very nice video
Yes, I was too lazy to change it :p
@@Nematics_Lab no problem bro...
I understand 😇
brother accidently i have switched the anode and shot all of them that means i switch the row and column opposite as you said
what will i do now help me
That means you hav to buy new leds
How did you bypass the resistors? You shot your ICs?
It's working with PIPO shift register?
Very good
Sir,
Make one video "how to change text
Expecting soon.
Tin lead yes, we don't use silver copper wire to solder
I solder 8x8 Dot Matrix. I use Anode as Column and Cathode as row. I use 2 of 74HC595.
I connect each row directly to 74HC595. Now I'm able to display text but it's flickering.
I was told to use 8 of BC547 transistor for each row.
Do they fix the flickering problem?
Speed up the frame rate. Scroll only every nth frame. Or use higher resolution
I don't want to scroll, what to change?
Is there any way to control the brightness of each LED using this technique?
You can add a simple PWM voltage regulator at Vcc
You run a high frame rate and dither. I Wonder if it is possible to put a latch after the shift registers. Then per row you can load new versions of this row where more and more LEDs go dark. Then clock the latch ( without the latch would worry about EMI ). Shift registers are fast. You can probably do 8bit at this low resolution.
Great sir ur first impression was very good . Sir plz make a full bridge inverter
Can we make it long ?
Thanks for the video. You make cool stuff!
Thanks
6
X and Y. Great idea
Can i increase the column no from 24 to 48 by using 3 more 74HC595 ics...? Plaese reply.
Yes
What type of components u use bro
So satisfying amazing
may shiba bless you crack! you are the BEST!
Cool but will the code only say nematic?
Nope you can change it to anything just have a look at code you will understand
Nice work
Can you make wireless / mobile controlled automatic water level controller.. To control submersible pump
Electronics + water don't go very well
@@Nematics_Lab But by using some transducers we can
I'll try someday
Great video! Helped me alot thanks
I want to make 8×32 LED Matrix. How many shift registers and Multiplexer ICs will I be needing?
4 shift register, 1 Multiplexer
What if I want to make bigger row and columns combination...what is the change in program
Bigger matrix will require Alot of changes in code
Cool...from where is the letter code (B100xxxxx), how to make it?please make video tutorial using RBG LED with 4 legs if you dont mind...thankyou
What does those ic's do?
Can it is modified by Bluetooth control?
ruclips.net/video/1rMRAoxxRm4/видео.html&lc=UgzHuGrJTzcSPbFClZl4AaABAg
Ohh thankss. Can you please give me full schemetic diagram of the project
Hi,Nematics,i am doing this same project but on the row,i used 74hc595,and it 8*40,
All things work right but the problem is i can not print out the numbers or some symbols like question mark on exclamation,can you please help me how to modify the codes so that i get the wanted result,
There is a link in description to my code check it out, it's easy to understand
Thanks
How many coloms i can add maximum ?
Interesting project dude :) keep it up
Led K kon Kon se part ko bord ke sath yellow wire se connect kya hain... please vi batao
is there need any darlngton trasitor or mosfet to give sufficient current to the leds?or not need bro?and can be it done with aurduino nano?then can u share the pic diagram?
hello, do you leave the arduino connected in the case of using the matrix as a display?
Yes
Hello Please tell me, what would be your best solution for connecting 200 hall sensors to an arduino microcontroller?
Use multiplexing
@@Nematics_Lab do you know any extender that has more than this --- macetech.com/store/index.php?main_page=product_info&products_id=23 ?
Very nice project.
How can i connect nodemcu to it...
How can get the PCB I want to do this project in my final year.
waiting for ages to do this project, had tried small matrix w/o shift registers, also messed up rows & columns so failed.
Where to buy silver copper wire?
eBay Amazon
As mentioned previously my strength is in electronics not Arduino software. I do not know which lines of code effect the addition of another 24 columns. Can you give some assistance?...thanks
HEY BRO I DIDNOT GET PCB LAYOUT IN DESCRIPTION PLZ HELP ME
Instructables link
I'm thinking to use UV leds to make a resin printer.
Nice job!
what wire did you used to connect all anode sir?
what are the different led matrices sizes (m*n) we can construct for an led display ., and by the way bro name of the pen you used for explanation in this video...????
Anything goes, but with more rows your duty cycle gets shorter and shorter.
Which resister is it?
please can it be controlled with Bluetooth, if yes, can you give the code and the circuit diagram thank u..
Here you go, ruclips.net/video/1rMRAoxxRm4/видео.html
Sir
Can JLCPCB supply ready-made pcb as per requirement
It is possible to not use ardoino ??
What the replacement of it ??
Can u build one ?
Nope
how can i connect led matrix with arduino uno
When do a class 11 student will learn about this?
In my opinion, start learning by yourself
Where is the file
Are you multiplexing each row ie 24 led?
If so,then how are you powering it as then the maximum forward voltage is greater than 45 volts and you are only using a 5 volt?
Please explain as i am only a beginner in arduino.
Thank you.
LEDs are all parallel, but most of them are at reverse polarisation most of the time.
Give me the link of circuit diagram plz
I could not find it in the video description
Check again
Sorry to disappoint you indian guy,but there is only one GREAT SCOTT.
ur pcb editing no possible due to permission,can u permit that?
Its awesome bro.. i love it
sir how can i modify the codes in order to print the numbers? PLEASE ANY ONE CAN HELP ME
Just download the code and look in it I have mentioned everything
Can i use nano indirect of uno
Yes
@@Nematics_Lab it need changes in code ?
Can i user 3.3v in uno board instead to make new ckt
5v is minimum requirement
And I know my next project!
How can we display date and time on this board?
You prepare the data in your favorite microcontroller and bit bang it over.
Short circuit, Johnny 5, you are the engineer in that film?
your gerber file does not work
Yes bro
Hey friend can you help me to make digital clock problem is only power supply, 1) First I purchased 2.5 inches(approximate) 7 segment display but it requires 9V for each segment and I was not able to use high side transistor switch, so I made my own segment display with 2 led for each segment and total of 2*7*4=56 LEDs, and they also not glowing as expected, now I'm working on 3rd experiment on bread board with total of 28 LEDs, one LED for each segment. So nearest 7 segment works with maximum brightness and decreases with distance, thanks in advance
is it possible to get all components packaged to me
Hi, I'm trying a simple version of this with 4 leds and I'm probably missing something. How am I supposed to light only the diagonal leds? According to connections shown, I can't understand how it's possible not to light all of them but pick just the diagonals...
Multiplex . You run over the diagonal . Eye can’t see it if you do it 100 times a second
Nice project
Please upload a picture of circuit diagram for buying the PCB from your given website
I am requesting to you 🙏🙏