I Broke My DANA 60 Axle Housing... Don’t Let This Happen To Yours!!
HTML-код
- Опубликовано: 6 сен 2024
- A few videos back, we took the JKU out for some high speed offroad testing. It did great, or so i thought.. At least we caught this issue early before it fully started to separate, which is unfortunately fairly common on these axles. I have had this axle setup since 2019 and they have done amazing! They however are not bulletproof (As found out from 40mph Ultra-4 course lol). The Barnes4wd Truss did a fantastic job holding everything together, and hopefully we can bend it back to spec and reweld it in place! To prevent this from happening again, Mike and I came up with a little lower mini truss for the axle. This will tie the diff and the tube in on the lower section, hoping to spread the load away from the pivot point on the tube/weld. We have to keep in mind that when we swap these axles into a linked suspension, we need to remove cast from the housing to weld our control arm mounts and shocks. By doing this, we naturally make the axle a little bit weaker. Some people will accidently cut too deep into the cast and score the tubes as well. This can also be a cause of something like this, if not much worse. In my case this wasnt the issue, and i did address to avoid that in my video playlist. I think we just took too big of a hit, too fast, without race suspension. So, my recommendation.. Truss, Weld Tubes, Tie in lower tube somehow. Im stilll a big fan of Junkyard axle builds, but im always welcome to finding improvements in spots that might need addressed.
Stay tuned for a 4 year review with these DIY axles! And of course an axle comparison video one the 2 door Crate axles arrive.
I would love to have pulled the axle and repair it correctly, however i am assisting Jeep Jamboree at Crossbar and need the JK ready to roll!
Garage Tools and Equipment:
Balljoint Press: amzn.to/3BHmYpj
M18 Impact: amzn.to/3JxDKZS
M18 Cheap Batteries: amzn.to/3BBXuta
Portable Work Platform: amzn.to/3bxD35Y
Crows Foot Wrench Set: amzn.to/3GEQyxb
Torque Wrench: amzn.to/3oQluS0
Allen Socket Kit: amzn.to/3JqpB0k
Crocs: amzn.to/3r7YXS4
Affordable Plasma Cutter: amzn.to/3H0eBqY
GoPro: amzn.to/3jZ1D0e
Interior Trim Removal Tool Set: amzn.to/3unUdce
Jeep Stuff:
Jeep JK Sunshade: amzn.to/3d2jBi8
Soft Shackles: amzn.to/3q0Y3FY
OBD2 Bluetooth Reader for JScan: amzn.to/3R7Tt4B
JK Grab Handles: amzn.to/3RgmTxO
JL/JT Grab Handles: amzn.to/3Rd6aLC
Warn Dana 60 Locking Hubs: amzn.to/3vzSWjs
Warn Zeon 10-S Winch: amzn.to/3AJR9tw
Magnaflow Muffler: amzn.to/3CQgg0O
Jeep JK Remote Start Kit: amzn.to/3XYjC9R
JKU Bedrug Kit: amzn.to/3DhWFFZ
She took it like a champ and we are ready to roll back to Crossbar Offroad Ranch to help out with the Jeep Jamboree there! Stay tuned on the JK build and what all these crazy parts mean! Thanks for watching, and make sure you turn on channel notifications if you want to stay up to date with the JK build projects 🤙🏻
When is that jamboree thing happening?
Drill out those plug welds in the housing and redo them. I added in more with my 8.8 Swap so it wouldn’t spin the tubes.
Your knowledge and abilities never cease to amaze me! I've learned so much from watching your videos, thank you so much for sharing.
Nice work Ben. Your mom was here for supper tonight, we cooked Hibachi and invited her to join us for mothers day. Keep up the good work.
You have given me tons of ideas of how I want to continue building my rig. Just have to find the funding to start really buying parts. However I felt you pain as you watched the bolts go flying every where.
Right about 11:50 in the video, Ben is contemplating his recent life choices. 😮
I married my high school sweetheart and we have been together for 40 years. I like your family and applaud your commitment to them and to your passion for Jeeps. Well done Sir!!!!!!
That must have been a good hit for sure! We had ours out in Johnson Valley ripping through the desert and now I want to go look at my axle 😆
This is why I watch all your videos you never know what you will pick up on. That bucket trick for dismounting the bead locks saved me like 40 minutes over 5 tires instead of fighting them standing up makes the tire pretty much fall right off. Keep making these awesome videos
You should leave some space on the repair lower plate for water drainage in case water ever gets in there.
Rock crawl = fun.
Rock run = your day is done! 😏
Haha that’s a good one!
You should come out to Rugged Mountain Ranch for the Tackett creek challenge memorial weekend watch the races and check out the park. It is just south of Hartshorne OK
Had such a blast with you guys at Crossbar this weekend!
I bent a wheel the same way and fixed it with a 4x4 wood block and bottle jack and some heat on the wheel. Straightened it out enough no one could tell and zero balance issues on the highway. 👍
Maybe you could plug weld the hole in the casting
I can’t wait for the 2 door videos to come. I’m still in the fence on which way I want to go ls or hemi with mine.
Solid advice. It will handle what it's built 💪 for.
Go Coasties. I loved working with the USCG. Cheers brother.
Another great video and looking forward to these future projects!
Love how you actually use your jeeps and looking forward to the V8 swap as well!! 👍
When it rains it pours my friend. Only two situations that jumping a jeep is ok...its your buddies that is sleeping with your ol lady and rentals😅
Man that is an awsome repair👍🏿👍🏿
Goodness the amount of pressure that thing had to have taken to crack that
Oh man when that tire fell over it was like scripted hahaha hope it didn’t take long find all the screws. Amazing videos as always!!
Can't wait to see what you have coming for the two door :)
I look forward to the 2 door build!!!
I have 2 rigs with SD 60s swapped into that i need to build these gussets for.. The artec truss welds to the inner C and might take some of the moment off the tube.
Dangit! Right when my checklist was about all crossed out!
Ben, we gotta wheel soon, we were both stationed in Virginia and spoke but never met up now I’m in Kansas and your in Oklahoma about hour and a half away hahaha
Look for a black 4 door JKU mountain on tons at crossbar sometime
Curious if you suspect the truss was partially the cause here? Wonder if the truss was already applying a bunch of upward force to the axle tube and when you got rowdy it added enough additional strain to pop that axle tube. Nice work.
Negative. Otherwise there would be a lot more truss related failures. This is from removing the cast diff section on superduty 60s
gotcha makes sense
@@JKGearandGadgets
How are you enjoying OK life? I hope you avoided the storms
Cut out some steel crescents the radius of the inner wheel and mount them to the end and base of a bottle jack and push that wheel back into shape
The reason that side cracks inst just because of the removed casting. The tube & truss is really short there. This means there is no material to dissipate the shock load.
Hey - Just wondering about the front SD 60 - a lot of places say 05+ ... until what year is that + good until what year? or even further?
I've seen some people say that they have an 11' with 5.38 gears.
Got a few deals with years all varying - just wanted some confirmation to make sense of it all. Thanks man and amazing to see the whole series.
For those interested, both Carli and Thuren offer a lower truss for Ram Dana 60 front . They may make one for superduty or may be able to modify the Ram version. Bombing the mega cab in the desert is fun from time to time 😅
Only issue is they are designed around the factory cast I think. Our trimmed cast and control arms get in the way
@@JKGearandGadgets I don’t think the Ram diff has the casting so far over on the driver side. I’ll have to check when I get home. I think some kind of mod might be necessary. Plus it’s going to hang lower on the pass side. I’m glad you posted about it. I now plan to reinforce my jeep front on the low side.
I may notch my truss to keep from cutting the cast
grab some trailready beadlocks and be done with wheels. Mine are 13 years old, been in a 40 mph accident and taken many hits over the years and still in great shape
I am not a professional welder. I see a lot of people using wire feed welder’s on axle builds. I would think maybe mig stick welders would make a lot stronger welds due to better penetration of thick axle tubes. Wire feed has always seemed for more light duty welds and axles are definitely and heavier duty weld.
As a CWI (Certified Welding Inspector) and professional certified welder, I highly recommend that you do NOT weld on that axle housing anymore if that’s the best you can weld. At a quick glance, I noticed the weld before you started grinding on it. If you’re going to use a 6010 type of rod, you better do another filler pass with a low hydrogen rod to cap it off. That’s why it cracked on you. All that undercut left from that weld actually left your housing weaker than it originally was. Congratulations.
Nice 😊 ❤ cool to see mor videos coming 😀 congrats
I doubt this will get out to you but take a bottle jack in the rim on a piece of wood and pump out the bend in the rim
Did you make anymore of those lower driverside brackets ? I would like to have some.
Lol I don’t think I’ve ever heard quick beadlock change before 😂
Me neither. I’m down to about 25 minutes per wheel . 4 pssses torque.d
What happens if you need to replace the “c”? That’s going to be work. Love your stuff. Like to ride with you sometime
You should check the axle seal and fluid since you heated up that axle so many times and up high temps?
Would it be wise to leave the oem housing intact in that area in future swaps? Does cutting off the housing serve a purpose?
Great upgrade and fix. What stops the passenger side from cracking? Wouldn't a longer tube cause more leverage on the welds on the center section?
I noticed that you didn't drill out the ends of the crack to prevent it from growing. Nice repair though.
I'm surprised you need to truss a Dana 60. Oh wow it is trussed!
Are you coming down to Jeep Beach Week?
Haha, what caused it. I gotta good idea
Always great info. 👍🏻❤️🇺🇸
i have the same setup as you. i would by lower reinforcement brackets from you
If you can trace this truss out on paper I can scan it,and draw it up in CAD for upload to a file share, or even make a printable scale PDF.
I was just going to ask you what dana axel should I go with, with a hemi on 37s. Lol and I see this...
*cuts away the factory casting* “Known weak spot”… imagine that
Forgive my ignorance but why couldn’t yo leave the casting and cut the truss so you don’t lose that strength?
A few things to note the axel itself was not a fault but who ever welding it was.. The shortening of the axel not likely. I can tell you 1000% was the welds of that that failed. Welds like that are not only terrible but dangerous. Be careful.
Some people don’t even weld the tubes back. In my opinion it was the shortening of the axle, as well as a lot of professionals opinion on this axle.
Naturally yes the weld failed, but if it wasn’t there the axle would have snapped in half
I have a 2012 jk with a blown head gasket what would you recommend doing to the motor while I’m at it
Don’t you need to worry about your seals with that much welding and hear while it’s all together???
I can answer all your questions concerning the cause of the broken axle with two words, lead foot.
And the question of how to avoid a broken axle can also be answered with two words, light foot.
But if it was an aftermarket crate axle would it have cracked? If i had this truss on would it have cracked? Thats what i want to know.
@@JKGearandGadgets not much can handle a big hit at high speed honestly.
@JK Gear and Gadgets ben i'm wondering if it's because just standard mig er70s wire was used? I think ni55 Is the proper thing to use. It's possible the weld was too brittle and started the crack. When I welded the tubes recently on my 14 bolt no matter what I did mig started to crack so I used that ni55 and it's perfect.
But I want to know too if the crate would have survived. Fusion has s60 housing for under 3 grand.
I think you guys are closet metallurgists...Wow!
My only question is aren't you cooking the inner seal and or fluid that close to ring and pinion.
Advance Driveline Axles ….?
i would do a root pass then 2 stringers over the top all while its been preheated, you already burned the hell outta that axle seal and carrier bearing, might as well put a real weld on it. i dont understand why youre scared of heat cycling when your already beyond that point with the torch.
Jeeps don't have wings so they don't fly! Make them fly, you will cry. LOL
You heated the piss out of that housing, the next failure is probably going to be the inner seal you melted LOL
I’d rather change out the seal than have a split apart axle on the trail haha. Luckily the 60s are thick and dissipate heat away from the seals pretty well
@@JKGearandGadgets I was just saying you should probably change out the seal since a considerable amount was put into the casting and was absolutely necessary for welding cast. I highly dislike oil leaks and axle tube leaks are suck a PIA to clean up and deal with. PS after reading my msg, I can see where I failed to communicate well, my apologies.
Ben, off point I know but which exhaust did you and Cassy go with on the LS in the LJ? The Holley/ Hooker stainless or cast? I'm looking for the discontinued stainless "Y" pipe.
Stainless. Not sure why they discontinued it, very nice kit
good video, but here's a suggestion for axle longevity.......maybe dont bash it up onto the rocks so hard.....but i dont know. im just sayin'....lol
Haha I mean you have a point, that’s a 100% foolproof plan lol
👍
Lemme guess which crate axles you're going with... Advanced Driveline?
You’ve been a good guesser before as well 🤙🏻
Why when you could go with east coast gear supply which makes the axles for advanced for cheaper
@@Cstepp connect the dots... Offroad Elements = Advanced Driveline. They've been featured on this channel numerous times. Ben's is or once was a Brand Ambassador for them therefore what you might pay for those axles & what it would cost him are 2 very different things.
Dayum. That had to be a hell of a hit. On the 2dr, are you going to stretch it?
Yes it will be stretched but not in the typical way. more on that soon!
Good morning. Did you shave the 14 bolt or dana 60 up front
Did the Barnes 13 bolt diff cover shave.
America 🇺🇸 💪🏼
Just a question do you need to worry about seals with that much heat?
Any chance the axle seals melted with all that heat
Like my wife always says, stupid hurts 😂
What gears you running on that one ton please?
5.38
Does the axle have inner axle seals?
Dude - you forgot to mention recommending side by side stuff is best done in sxs or KOH built jeep…. Jeep is best left to keep stuff. 🤣😂🤣
Had to pause the video to hide from tornadoes
Glad you’re safe!
Another option is to slow it down a bit. 😂
Should have cut the truss it would have pulled down with less force and then welded the truss back up
We thought about that! But need the jeep asap for jeep jamboree at crossbar to help out lol
So strang UD60 with full support get cracked
Thats the issue with low profile trusses... they arnt actually trusses
And the next video will be how to change your axle seals because your seal looks like bacon 🥓,,,,, 🤣
No issues with the seals the first time I welded this up. The 60 is so thick the heat dissipates before the seals can get damaged
A rosette weld inside the port you saw the half moon?