Интересно а где это собирают, в Японии капиталки не делают. Молодцы ребята. 👏👏👏👍👍👍✊эти двигатели очень надëжные и качественные, да и Lexus тоже, привет с Камчатки. 🗻🗻🗻
Ola..sou mecânico aqui no Brasil..seu trabalho é de excelência..parabéns Qual seria esse produto q vc usa p limpeza das peças do motor? Se me responder ficarei muito honrado Obrigado
As an engine builder, I didn’t see any thrust bearing measurements, cylinder measurements or checks for worn rings, worn bearings or any tolerances at all. This good entertainment for anyone who knows nothing about an engine but I’d give that thing 5-10k before it starts smoking, knocking or just locks up. You NEVER reuse pistons and rings, especially in an aluminum block.
I'm sure it was all done. The video would be twice as long if all that was shown. They're not going to have that kind of set up & do all the vital parts of a rebuilt. Amateurs, however, it would be typical that they would blindly trust what they receive even from what was given to them by the machine shop, & not a minimum check for oil clearance with plastigage.
Puedo darte una crítica ?? Cuando tú aceitas los tornillos ,y estos llevan un gran torque( o kilos ) si oos aceitas modificas dicho torque , hasta puede que se estireny corten antes de llegar al torque indicado . Me a pasado en grandes torques más de 40 kg
Just a couple of questions please... number one, do you also rebuild the transmission? And what about the differential? Lastly, this would seem to be an entire remanufacture of the vehicle. So, what is the cost to do this kind of work in comparison to buying a new vehicle?😊😊😊
I think it would be cheaper to buy a car and have it shipped to China. Have it restored, then shipped back for less than anything like that here in the US.
The first reason is, this is an all aluminum block, second is the tolerances on the head to block is so close and precise almost zero, there's no need to machine it.
@@mikemurray2298 so in that logic, just because it’s all aluminum, it can’t warp or be machined? A head gasket is about 0.008” compressed, which is tight but there are thicker gaskets for that reason.
This information came from a well renowned factory certified Toyota technician on RUclips (The car care nut) that since the tolerances is so tight on a Toyota engine your not to machine the heads. Ask a factory trained Toyota technician to verify this.
No tolerance checking? How do they know the bearings have the right spacing. No plastic gauge or lead test. The assembly oil looks very thin. You need something that sticks to the part also for 1st start up of the 7:13 engine. Just forma gasket not a very good job just bolting it up and hope all is well.
Dude, I thought they were building an engine for a frigging race car! When i saw they put that meticulously built engine in that old ass junker I was shocked!!
Esos liquidos usados a saber donde los tiran.... seguro que no los reciclan bien... China junyo con La India... los que más contaminan... por muy limpio que deje el motor.... a saber donde tiran yodos esos liquidos
Парни вы просто волшебники! Столько внимания одному автомобилю, но результат стоит того!!!!! МОЛОДЦЫ и видео красивое!!!
I'm really impressed how this mechanic performs his job. Very meticulous and thorough. And the workshop looks very clean and tidy. Great work!
@@maciejbrozek4666 Thank you so much👏👏👏👍👍
The most impressive part to me is how perfectly he spreads the RTV Silicone
មានសេវាកម្ម បែបនេះពិតជាអស្ចារ្យខ្លាំងណាស់ .....👍👍👍❤️❤️
@@haytang3859 😍😍😊😊
Лучьше чем новый😅😅😅
Поекраное творение, инженерной мысли Японии.
Вот это уровень!!!!!
That’s the only place I would take my Lexus to get rebuilt. Perfection!!
@@carlossantiago3599 👏👍👍
Класс!!! Молодцы! Эх, мне моего старенького Субаря к ним на апгрейд бы загнать!😊
Maravilloso! 👏🏼💪🏼✌🏼
This is not a restauration, it's a resurrection! The attention to detail is staggering. Hats down on your professionalism 🫡
Молодцы. Этим парням я бы доверил свою тачку.
@@aleksandrsemenichenko6241 😂👍👍👏👏
What you use to degrease and clean the engine block and parts at the starting of the video?
La Técnica vs La Fuerza, Exelente Servicio y Trabajo de Calidad.
😮😮😮LO muy menos es el carro que usa el mero Jefe. Cuánto cobrarán x un trabajo así...??que excepcional Cuánto detalle...WOW..😮😮😮😮😮😮😮❤
Impressed with the professionalism and skill. Guys a master with that gasket sealer. One thing though, never saw the valve lash adjusted.
What a beautifull engine!! Great job 🫡🫡
@@josephgordan1167 Thank you😃😃
As a former aircraft mechanic I really appreciate the attention to detail. But that job must have cost a fortune
Молодцы ребята! Класс!👍
Beautiful, I could watch this all day. Excellent work and fantastic clean workplace 👍
Классная работа 👍👍👍👍👍
@@mikhailpichuev898 👏👏👏
Всё как в аптеке ❤
臺灣就沒類似這型恢復修工廠..
Um dos trabalhos mais admiráveis que considero, toda essa complexidade me cativa. Parabéns pelo vídeo!
excellent work, great dedication, but the car will be more expensive than a new one.
That's what I thought 😮😮😮
Ваще пофигу. За такую классику отдать не жалко. Чем за новый 2024 года.
100%. 👍👍👍@@НиколайПоторочин-ш1ч
This can be true for US, but for a lot of countries it's less expensive rebuild the engine.
Hopefully. That's one of the best cars in the history of automotive industry. Worth every penny
Congratulations 🎉
@@arisrodolphe4 Thanks a lot
I can watch for hours 👍🏻👍🏻👍🏻
@@andreasnauen9927 Thank you so much!
For real. It’s meditation lol
This is how a professional rebuilds an engine
I want that digital torque wrench!
Красиво снята работа гайковерта. А кто основную работу проводит в пределах допусков?
Тиктокмеханики.
Интересно а где это собирают, в Японии капиталки не делают. Молодцы ребята. 👏👏👏👍👍👍✊эти двигатели очень надëжные и качественные, да и Lexus тоже, привет с Камчатки. 🗻🗻🗻
@@СергейСарычев-у3у Thank a ton
Beautiful job.
@@williamjamison5010 Thank you
Ola..sou mecânico aqui no Brasil..seu trabalho é de excelência..parabéns
Qual seria esse produto q vc usa p limpeza das peças do motor? Se me responder ficarei muito honrado
Obrigado
Dá gosto ver um trabalho assim.
Ficou como novo.
👏👏👏👏👏
@@emmanuelH. Thank you so much
Incredible job, its like new.
Thanks
Çok güzel oldu, Fakat yenisi ile neredeyse aynı fiyata gelmiş olabilir, İşçilik Harika tebrik ederim
Авто не надоедает раз такую работу провели
Zor judayam chiroyli
total transformation and a well done job.
what hot chemical did you deep the engine into before pressure washing it
Top work team
@@WGITCCRS Thank you
As an engine builder, I didn’t see any thrust bearing measurements, cylinder measurements or checks for worn rings, worn bearings or any tolerances at all. This good entertainment for anyone who knows nothing about an engine but I’d give that thing 5-10k before it starts smoking, knocking or just locks up. You NEVER reuse pistons and rings, especially in an aluminum block.
@@tstemen1047 have a good day
I'm sure it was all done. The video would be twice as long if all that was shown. They're not going to have that kind of set up & do all the vital parts of a rebuilt. Amateurs, however, it would be typical that they would blindly trust what they receive even from what was given to them by the machine shop, & not a minimum check for oil clearance with plastigage.
Super nice, wow. How much would something like that cost? I'm interested
2011 four-door Silverado Short bed
That’s a second life given
@@thomasjeangerard6268 😍😍😍
Outstanding!!!
@@davidrippy1605 😍😍
Интересно, сколько стоит такая работа?
Es agua caliente simple maravilloso trabajo
Классное видео
Excellent
ini cara aman refresh mesin tanpa overhaul mengembalikan mesin pada performa awal tanpa merubahnya...
@@dencielo784 😍😍
Show
Top de mas 🎉🎉
@@jairosoaresduarteduarte7694 Thanks
Никогда не делал подобную работу в перчатках. На них не ощущается грязь. Помыл руки ,ветошь в карман и вперед.
They should do a video on my vk45de engine. I would happily donate.
I have two vk45des as well would love to see but I am going to be the one doing it myself
Блин новая машина, обсалютно стала 👍😎
@@Артем-л7щ8к 👍👍👍
Impressionante. Ficou como 0 km
Puedo darte una crítica ?? Cuando tú aceitas los tornillos ,y estos llevan un gran torque( o kilos ) si oos aceitas modificas dicho torque , hasta puede que se estireny corten antes de llegar al torque indicado . Me a pasado en grandes torques más de 40 kg
When oiling screws, it is best to use the table for oiled screws.
Belissimo trabalho
Excellent job! How much did it cost?
I was going to ask the same question….
Движок собирает,как доктор!!! Смотрите криворукие мотористы!!!каждый болт через динамометрию !!!вот где настоящие СПЕЦиалисты своего дела!!!
@@user-su6zl5yn9v Thank you very much
Just a couple of questions please... number one, do you also rebuild the transmission? And what about the differential? Lastly, this would seem to be an entire remanufacture of the vehicle. So, what is the cost to do this kind of work in comparison to buying a new vehicle?😊😊😊
Thanks,i don't rebuild transmission.
WOW 😮
Nice bead on that oil pan
I think it would be cheaper to buy a car and have it shipped to China. Have it restored, then shipped back for less than anything like that here in the US.
Bravo😂😂
🔥 🔥 🔥 👍
Great job 👍..... however, i didn't see valve lapping!
@@normandaquioag8067 Thank you so much
You don't know if they did a valve job before.
Также, как и регулировки
amazingly great... where I can restore my car as shown in the video
Thank you
On RUclips 😂
at the start of video, was it a chemical soak or ultrasound bath or degreasing spa?
@@FishingSGsWild sorry,i don't know how to say it in English
@@mechanic-miaer type in , i can use google translate
Mengunakan cairan apa untuk melepas kotoran tersebut... ?
Which liquid do you use to clean engine parts I'm Engine Mechanical light vehicle light vehicle for India
What's in that squirt bottle? Oil? What kind?
А разве можно смазывать резьбу для болтов под момент затяжки? 🤨
wow
👏🏼👏🏼👏🏼😍😍😍😍😍
Нашим сервисменам не показывайте, засмеют такой не профессионализм, ещё и в перчатках и кругом чисто. Сразу видно - Постановка.😂😂😂
You have not showed us how you grinded the valves on the seating.
@@HafizurRahman-mw8bp maybe you are right
What no sandals no robes ? Tight work ...!
Work well done but they didn’t machine the deck at all. Wonder why?
The first reason is, this is an all aluminum block, second is the tolerances on the head to block is so close and precise almost zero, there's no need to machine it.
@@mikemurray2298 so in that logic, just because it’s all aluminum, it can’t warp or be machined? A head gasket is about 0.008” compressed, which is tight but there are thicker gaskets for that reason.
This information came from a well renowned factory certified Toyota technician on RUclips (The car care nut) that since the tolerances is so tight on a Toyota engine your not to machine the heads. Ask a factory trained Toyota technician to verify this.
@@mikemurray2298 to me, that makes it a throw-away engine.
No timinng chain ,no shity rockers.That video for audi ingeniers.
Залепательно
Did you put in fresh piston ring nothing is clear only showing fancy work.
@@HafizurRahman-mw8bp 😄😄
I changed my oil once
@@nitdiver5 well done
A direct copy of the FORD 351W....all.motor guys know that!
With dual overhead cams? Aluminum block? Maybe
not quite an exact copy!
Can I bring my old bmw to you as well?
@@martinthemillwright yes,you can
what kind of liquid is in the bath?
@@dmitryduma sorry,i don't know how to say in English
@@mechanic-miaer お風呂の中にはどんな液体が入っていますか? translate Google)
White rhinoceros piss.
Acid solution
@@arleigh31burke-zc2om ty!
All that pollution for a fuel burner. Disgusting!
Whats the cleaner solution?
@@marineyacht l don't know how to say it in English
Google translator 👌🏼
Что то заказчик нового китайца не купил,а ввалил в лексус)))
Don't like the gloves,,,and airtool when assembling an engine.
Everything is beautifully cleaned though.
Muito motor para pouco carro.
No tolerance checking? How do they know the bearings have the right spacing. No plastic gauge or lead test. The assembly oil looks very thin. You need something that sticks to the part also for 1st start up of the 7:13 engine. Just forma gasket not a very good job just bolting it up and hope all is well.
明明是“鲁”的车牌,整备后变成“甘”车牌
How do you clean the engine
@@mohamedkhodier7113 Ultrasonic cleaning
@@mohamedkhodier7113 If you don't have ultrasonic equipment, you can use gasoline to clean it.
Я такую же хочу 😢😢😢😢😢😢😢😢😢😢😢😢😢😢
@@сажа-э6к ???
@@mechanic-miaer автомобиль такой же хочу
Did we check our tolerances?
Acho que é desengraxante e descarbonizante.
why?
Oiling of bolts means you dont understand how it works. There is no knowledge of tightening principles.
Dude, I thought they were building an engine for a frigging race car! When i saw they put that meticulously built engine in that old ass junker I was shocked!!
@@goodcitizen7064 I'll take that old ass junk any day compare to the new ones we have now these days!
Definitely not a Jasper engine rebuild!!!! Lmao
สุดยอดเลยเก่งกันทุกคนเลยและอยากทำแบบนี้บ้างค่าใช้จ่ายเท่าไหร่ครับ😊😊😊😊😊
🤔 20,000 USD?
So was that a car that was "acquired" in Canada??
❤
А потом везут на продажу, который потом ходит не долго.
Esos liquidos usados a saber donde los tiran.... seguro que no los reciclan bien... China junyo con La India... los que más contaminan... por muy limpio que deje el motor.... a saber donde tiran yodos esos liquidos
That how you do it