DOLCE GUSTO Piccolo - Step by step disassembly - NESCAFE Krups KP100
HTML-код
- Опубликовано: 23 авг 2024
- Hello Guys and welcome to a new video. As the title says this is a full tear down / disassembly of the Nescafe Dolce Gusto piccolo machine KP100 KP100A KP100B etc
![Kodak Black - Sharp Vibes [Official Music Video]](http://i.ytimg.com/vi/oEV0OoLJeIs/mqdefault.jpg)
Thank you for the disassembly video. For those who have the same problem like me: After switching on the machine it should blink slowly red (about 1x per second) during the heating up then it turns to green steady light - ready to pump the hot water. When it however shortly after switching on starts blinking red faster and never turns to green it means there is a problem with the heating. In my case it was just a bad contact for the NTC sensor which was otherwise ok (my had about 150kOhm in normal temperature).
Thanks for sharing your experience with others. 😉
Same here...
Thanks for sharing
Can someone help , my machine takes long to become green how to fix that , please
Worked for me, had to change the gasket where the water tank sits and that had leaking for ages and finally got round to fixing it. Thanks for the video, it helped enormously
I had the gasket problem also which required disassembly before I'm able to access that circular/tubular gasket which holds onto the water outlet of the removable water tank. I managed to fix that by just dropping an additional O ring which just fits nicely into the hole, and then dropped the original gasket over that. Since there is less longitudinal travel of the tubular gasket, it grips the water outlet better circumferentially.
Worked.
@@thliew6362 did it then stay in the hole or around the shaft of the tank. Did u put Xtra o ring underneath original one or around original one to make it more fat and stay in the hole please help.
I have the same problem.
Where did you got a new gasket?
@@boorandras9723 Try with o-ring 15x3.5. It works
Thank you for your video...I had to take out a suspected faulty pump and your video save me a bit of time... Turned out the problem was underneath the water select lever as the hot water tube stayed closed due to lack of use...I managed to remove it and turn it around 180 degrees so it was 'fresh' tube under the lever...
Thanks again
Tnx for this detailed video. I used it and managed to solve reservoir leakage problem by replacing a single o-ring.
🎉🎉🎉🎉
Ďakujem,super video, podarilo sa mi z dvoch pokazených kávovarov vyskladať jeden funkčný kus.Poučné -dík.👍👍👍👍
Thank you! You video is very helpful. I had a problem with a pump. After disassembling the pump I found some problem with small balls inside the pump. They didn’t move properly. After reassembling the pump the problem was solved. Your video helped me to repair machine for 2 hours. 👍👍👍🙏🙏🙏
Românii, mereu inteligenți, se descurcă! Romanians, always intelligent, manage!
Thanks Adrian!
Cu plăcere!
@@benassy69 hey! Ive watched all your videos related to dolce gusto. I have a dolce gusto picolo, and water pours from cold side but nothing from hot side. Do you know what might be the reason? Thank you and your videos are very helpful!
Thanks, man. If it hadn't been for this video I wouldn't have opened this mean machine.
Thank you very much for this. I have cleaned the seal which was caked in limescale. I cleaned it inside and tested it. Nice coffee and no leaks. Great video.
Thanks! After spending somes hours to find why the water pump refuse to start (take mesures on triac of the pump, Z3M, take datasheet of the microcontroller, a STM8S003F3P6, i have finally found the problem: the sensor on the HOLD connector don't work. If i short it, all working nice. So, after viewed your video, i have checked the magnet on the plastic module for the caps, and it was missing. Glued another one, tested, all working!
Nearly 4 hours for a stupid magnet ;)
Thanks to you and your sharing!
The pump in mine is not starting either can you tell me exactly what you did to fix yours? I could not understand exactly what you did. I was going to buy a new pump thinking that was the problem but maybe it is something as simple as what you are saying. Where is the HOLD connector and how do I check it?
@@mmendoz7677 (sorry for my english) to test if your problem is the same as mine, just make a short on the two littles wires that came from the board HOLD connector to the top of the coffee machine (it go behind where the caps holder is).
So, more simply: disconnect the cable marked HOLD on PCB, and make a direct connexion between the two pins (a short circuit), and try to start your cofee machine. if it work, look under the cap holder (where you put your coffee caps), and check if there is a magnet on one side. if there is no magnet, you have just loose it, like me. You can buy some for some bucks on amazon/ebay/ali express, just search neodymium magnet, and look for a size who fit un the little hole under the caps holder (maybe 5mm by 3mm by 1mm, don't remember), and glue it with hot glue or super glue (test the right position, left or right, with hot glue, before make it definitive with super glue^^)
Really simple to show, but hard to write^^
@@zapanjormas4787 thank you so much! I really appreciate your reply. I am going to open it and see if I can follow your directions. You should make a video tutorial of it, pictures make easier to explain : ) Will definetly try this first before ordering a new pump. Thanks again
@@zapanjormas4787 Hey I have not been able to figure out where this magnet is supposed to be. Can you help me?
It has to be in the wall of the capsule drawer/holder. There is a resign over it. Take out the capsule holder and see if you have a hole inside. If yes the magnet was lost when you have clean it. If you can see the shiny resign then the magnet is still there and the sensor on the other side might be the problem.
thank you, just needed to remove the o ring as it had gotten brittle and this made taking off the shell a breeze!
Thank you so much. Your video really helped me to fix mine
Excellent video and explanation of disassembly. Thank you.
Thanks a lot for this video, you saved me a lot of time and nerves. My unit started leaking some time ago, after dissasembling it turned out that inside everything is ok but it is the water tank that is pouring some water. Any thanks again! :)
What did u do to fix. I think mine is leaking from where tank goes into the hole. There is rubber washer. Should it be stuck into the hole on top of the filter or should it stay on the shaft of the water tank.
@@martymartin2894 The plastic water container was cracked and it was leaking from it. But now I have the same problem as you are describing. I cannot find a way of fixing it so I just live with it and it will endup in a dumpster pretty soon. Not worth of my time fixing it anymore.
@@marcin7928 I bought another one a infinissimo but I still tried to fix this but I couldn't so I threw it out. There a bad design because u must remove the small tank each time to refill and this in time wears out the rubber ring. On the infinissimo u don't need to remove tank to refill only if u want too. U can fill from the top.
thanks a lot! I manage finally to clean the mud in the pump. However, putting plastic cover back is a nightmare
Thanks, wonderful guide!!
Thank you very much! It's very helpful! 😄👍
Well done, thanks a lot - had to change the watertank gasket. works fine despite all those horrible clips 🙂
I do not know if anyone wrote it, but i noticed the heating element is not hard at all to unmount. After disconnecting it, you only have to rotate it counterclockwise, as seen from above and thats it...
Or pull the plastic holder backwards after you press the two tabs from under the device. Its a little bit mor dificult, so unscrewing the heater fron the plastic holder is the easiest way...
Thank you Adrian B .
Thanks. Your video really helped me to fix mine. :)
Thanks for great and detail instruction
Thank you so much for this video!!!👍👍👍
I'm glad you found it usefull!
Nice info for this machine. Thanks
very enlightening ! thanks
Many thanks to you! Very helpfull video.
Ciao, thanks the video, it was easy to repair.
I have a problem.. When the mashine start, everything is ok. But when I swich down the buttom, the water will come inside at the down side. What is the problem, or where?
Thanks for very helpful video :-)
Thank you my friend ,now i will dismantle the machine to see why all the water goes to my ...feet!!!
Hi Adrian,
First of all thanks so much for your videos, really helpful.
I have disassembled my mini me machine to change the seal rubber and as I tried to reassemble the top handle does not work properly and I am not able to insert the coffee pod holder anymore and cannot figure out why. :S Any chance u could give me advice, please?
:( Thanks so much in advance
Why why why didn't I believe the part about a blocked nozzle ! Dissembled following your excellent instructions then realised it was just a blocked nozzle. But it was something interesting todo. Thanks.
GRACIAS !!! PUDE ARREGLAR MI CAFETERA GRACIAS A TI !!
Me encanta . Gracias!
Thanks for such a great video of how to dismantle the machine, it was much appreciated.
The problem I have is that the hot water stops very soon when it is filling the cup. I have checked for blocked nozzle and there is no scale in the tank.
You mentioned that this fault could be due to a faulty capacitor? Now that I have the pbc out, I can see 2 large yellow capacitors and also a third one which is slightly smaller. Can you please confirm which one I should replace?
Hi the biggest one. It should be a 680uF cap. Or a 6.8 nF it is actually the same thing.
@@benassy69
Thank you for your reply.
Can I please check with you, the capacitors on the pbc are 2 at 0.56 uF and 1 at 0.1 uF. Which of these are linked to the problem I am experiencing?
I can send a photograph to you if that is possible?
The 0.56 one
Thank you very much, it worked! 😅😅❤
Büyük insansın. Eyvallah
Nice video sir, can you assist me, my machine does not pour water, i already clean the pin but still no water is pouring, what is the problem with this sir. Thanks for your time.👍
Hello Adrian,
Could you make a video or tell me how to replace NTC temperature sensor in this machine? Also how we can check if it even works? I have problem with no response at all after trying to power on. I think that fuses are ok and now i suppose that it is a problem with the PC board or temperature sensor.
Hello Monika. The NTC sensor is not blocking your machine. It is there only for overheating purpose. Please try the HOLD sensor. That one is causing machines to not work most of the time. Tri shorting the 2 pins on the HOLD connector from the PC board and see if it works.
@@benassy69 Could you please add a photo or some indication to locate the HOLD sensor? thank you very much
Ah, Okay, it's the capsule holder just at the left side of the NTC sensor.
But the result it's the same. The button start blinking red and then just switch off
Thanks a lot for this useful video .
Thank you for this video!
One question: Is this pump similar to the one in the KP120 unit? I have a KP120 with a dead pump and was hoping to canibalize a KP100 for its pump.
The pump are identical on almost all Coffee Machines. So the answer is yes, you ca use it.
@@benassy69 Thank you! In the meantime, I had already tried to replace it and it worked! Thank you so much
👏
Very helpful.
Thank you
Hello Adrian your video was a great help to dissasembly the machine. Since you are experienced with this machines you may can help me. My machine overheats, when it was swithed off. I replaced the thermal fuses on boiler. Try the macnihe and was working fine. But after few cofee it overheats again, when it was switched off. Dou yu meet this issue earlier?
Have you tried discaling the machine? Limescale sticks to the walls of the heater and causes overheating.
@@benassy69When the machine is on works fine. Heat up quite quickly and keep the temperature. When switch off. (power button not light) after 5-10 minutes it boils the water, steams come out and terminate the thermal fuses. It happend two times. Seems somehow the boiler triac is fired when the machine is off. During operation it works fine.
After 2nd time it boils the water, I measured again the electronic, and the boiler triac was continuously fired even after removing the resistor from controller. (triac was not in short circuit measured with DMM) I replaced the triac seems ok now.
Cheers !!!!!!
Hello Adrian. Strange problem here. I have a problem with the spring and the plastic regulator inside the tank. When i lift the tank they fall down. Also the plastic regulator with the o'ring dont look normal. The head is ok but the body is very thin like a toothpick. i suppose they used something caustic. I dont know the anatomy there, how it was before to try to fix it. Any advice?
Thank you .
You are welcome!
Dear, Adrian!
Yesterday I transported a used Dolce Gusto Piccolo machine lying on its side by car. I emptied the water tank before leaving, but the pipes inside the machine and the heating unit must have contained water. I thought that the internal part worked as a closed system, but upon arrival I noticed that a small amount of water had leaked out at the joint of the machine's cover and at the power button.
Is it dangerous to use? Should I let the machine dry for a few days? Perhaps is it recommended to remove the cover of the machine and check the dry condition of the inside of the machine? What do you suggest? Thanks!
The water should not leak inside. Let it dry for one day and you should be fine.
Thanks for help me ☕
Hola que tal.queria consultarme mhj maquina dolce gusto de de marcar la medida de cafe que seleccionas.tenes alguna idea ,de cual puede ser el problema?
you are AMAZINGGGG
Thanks Bro!
Thanx dude!
Had to pull a Dulce Gusto oval type to fix a leak and that Hall effect sensor fell out now I know what it does,thank you.
Salutare !Bune tutoriale faci frate !🎉🎉Am și eu o rugăminte,pe linia de făcut băuturi reci ,cred că s- a depus "piatră" și numai pot face decalcifierea mașinii.Cum pot deschide porcăria asta ,DG ESPERTA?😢
Salut din păcate nu am desfăcut niciodată modelul acesta. Din ce oras ești poate mi-l poți aduce și sa fac și un video cu aparatul.
i watched till the end of your video.expecting you will do something. a common problem on a capsule espresso machine.which is the pump. vibration pump.
The video is a step by step disassembly what else you wanted to see till the end? Or did I misunderstood your comment?
Hi my machine stop to come water and not working . Do u know what’s is wrong?
Thank you
Hi i have probleme the pump dont make sound thewervare power so i dont know what is the flolt it
Hello. I have one question how I change o-ring on Krups Dolce Gusto water tank? Thank you for your tips. Saso
Look on my channel I have a video on how to do it.
Hi,
I hope You can help me. I have this caffee maker machine. When I trying to power on and make coffee the red switch is starting to blink and after 2-3-4 (random) blinking it stop doing anything...seems like it is in "off" state...when I set the caffee maker to cold water during the red blinking state, its start to pump cold water (and the switch changes to green immediately).
Is the problem with the heater? With the electronic (PCB) component? Yesterday I disassembled it but found nothing (not found burnt element or anything)
Sorry for my bad english.
I hope You know which part of the machine should be changed....or should buy another? It could be easier... 🙄
Hi. Based on the simptomes you described I presume one of the capacitors on the board gone bad. In most of the cases is the bigger box looking cap on the board. If you can desolder it from the board and measure it with a multimeter. If the value written on is is higher than the value on the meter you have to change it. It is really cheap.
@@benassy69 I have everything for it ..going to check. Thank You very much. (I'll inform You what I found)
@@benassy69 if i could, to really test an electrolitic capacitor, you need an ESR meter: an electrolitic capacitor could be nice to look (not "bumped", have a good capacitance, but a bad ESR. If you cannot get an ESR tester, change the two 470µF (if i remember well^^) 16V. It cost nothing.
I removed but I cant installed 😢 have you video for installation?
Can I fix my dolce gusto machine that just won’t turn on?
Hallo Adrian. my Piccolo Krups machine switches off with the hot water lever. Cold water lever works instead. What shall I do? Help
Hello. You need to change the box looking capacitor on the main board. It is really cheap and it's value is 680uF if I remember right.
My machine is making buzzing noise but no water comes out. Could it still be the pump ? Because as far I can see from the input - no water is taken inside ?
Clean first the diffuser plate. Ses my video " Easy fix..".
Thank You big time; watched other videos aswell and found my solution ❤
hi my machine has roaches inside breeding will it help if i take it apart and clean it
Roaches? Throw it away!
Hi Adrian! Thanks for your video, I made it to open the machine just because of that! Maybe you know what happened to my Dolce Gusto: I tried to empty the circuit by making the machine running without water (I’m a GENIUS, am I not?). After that it didn’t work anymore. Maybe is a thermal protection that fused?
Hi. By running the machine w/o water you've created an air pocket. The way the pump works is that it always needs water to make vacum. Try filling in the water tank with water all the way up and run again the machine. The weight of the water could be enought to create some presure and start it again. Or just force some water into the intake when powered on. Hope my instructions help. BTW I have a video on my channel on this topic.
@@benassy69 Thank you man! I’ll go check the video and let you know! I should have done it BEFORE opening the machine 🤣🤣🤣
Hi,
Do you have advice how to remove the shell with genio s plus?
A capsule (nespresso) adapter got stuck in mine and I have no idea how to take it out. I am afraid I will break it.
You used a Nespresso adapter on a Nescafe machine....no bueno! Try smacking the unit over the hear (up and on sides) and in the meantime wiggle the capsule try.
@@benassy69 I managed to squeeze in a flat head screw driver between the adapter and the machine and got it out. Yayyy! Threw out the adaptor. 😅
Hello, my machine turns on, but when I turn the lever to operate it it it does not give any signal. Do you think it could be the magnetic sensor?
Yes. Change it or shunt it
@@benassy69 Thanks for the reply, just 10 minutes ago I tried to connect a magnet to him and it worked. The problem is that the original magnet has detached from the capsule holder. Anyway, thank you the same friend
Hey Adrian can you help me with my mini me? A coffee capsule broke and flooded the inside of my machine with coffee milk and now it wont turn on or work. I tried flushing the milk out of the maschine under the sink. Would dissasembling it work or is it broke forever?
If you are from UK you can try by checking the fuse in the power plug. If not inside there is some fuses on the heater element and pump. If all are ok, then is something on the main board. You can order a new board and swap.
@@benassy69 im from Denmark. It suddenly works now? And then doesnt work again. Really weird. Do you think its because theres still milk/water inside the maschine?
When i turn it on water comes out immediatly now, instead of me pressing the button and flipping the cold/hot button and it doesnt measure the water now. It just keeps going
Disconect from power imediatly. You have leaquid shorting on internals. Open it up and clean it inside and the electrical connections with alcohol. Ok leave it be for 2 days to dry out.
@@benassy69 thank you! I will try.. also thank for answering quickly
I looked and looked but can’t find instructions or mention of the metallic plate at the back of the capsule holder; can you help please
I tried to send a photo but I wasn’t able
if your one isn't magnetic (the test with the screwdriver in the video), you have lost it, like me. I take some neodym magnet that fit in the oblong (there is one larger on one side), fixed it with hot glue for test. Test ok, so fixed with Super Glue.
Which srewdriver is needed here?
Torx 10
👋
when i plug mine into the socket its turning on and i can t stop it
Bună, domnule Adrian !
Crezi că mă poți ajuta cu un aparat Dolce Gusto KP2000.
Cred că este înfundat difuzorul, curge apa pe lângă clapeta de introducere a capsulelor.
Mulțumesc în avans !
Salut Petru! Clar problema ta este de la acel diffuser plate. Exista 3 variante de a repara aparatul. 1 schimbi diffuser plate-ul. Se găsește de cumpărat am și eu de vânzare pe OLX. 2. Desfunzi diffuserul daca acesta este înfundat. Am un video pe canalul meu cum se face. "Dolce Gusto not pouring water EASY FIX". 3. Pui o garnitura mica peste garnitura diffuserului. Caută videoul meu "DOLCE GUSTO leaking water".
@@benassy69 Domnule Adrian !
Chear acum urmăresc videouri-le, tale. Problema este că nu găsesc acea gaură pentru a desface difuzorul😁 normal, este vorba de Dolce Gusto KP 2000 !
Am demontat de jumătate aparatul, dar m-am îmotmolit la cap🤔
right out the box mine didn't work
I have a problem. The red light blinks and after a while goes out. After turning it off and on and taking the capsule out and back in again, it somehow turns green, but it's a struggle. Does anyone have any idea what it could be?
Check the box looking capacitor on the main board. It should be a 680 nF
My piccolo machine is hard to switch on. I need to press and hold the power button up to 30 seconds before it switches on. I didn’t see anyone else have this problem, I wonder what can be the source?
Yout button Module is defective.
@@benassy69 thanks for the reply! I will take the machine apart and take a close look at that button. Maybe it can be disassembled and cleaned inside, or perhaps I’m lucky and it’s just a loose wiring connector at the button module. These machines vibrate so much, it could just be wiring
Подскажите шимку на плате , если кто помнит )
Can't even on it with the stuck tray
Forget it. Pump proberly died
the most horrible construction ever, full of plastic clips that bend and breaks, 1 hour to take apart, 1 hour to put it back ... ....whoever designed this needs to be jailed.
that o-ring at the base should be easy to change but no, they put that plastic cover fused with the case , even if you take those 2 screws out , still not enough , the plastic round cover is fused with the case....
this is made to be put in the bin, not repaired.
Hi Adrian, just looked at 3 of your Dolche gusto machine videos as my machine (it's second hand and in really good condition) isnt wanting to pick up water. I watched and followed your water injector video and after cleaning no water is coming out of it or being picked up... I think it's the new jug, (previous one broke 🥲) or the pump itself. I'm probably just going to buy another one. What would you suggest?
Hi, do you hear the pump working? If yes try removing the diffuser plate and see if water is coming out. If yes clean the diffuser plat or buy another one.
@@benassy69 yep, I followed your videos and removed the plate, cleaned it put it back and pump would work but no water would come out. I've just tried it again after leaving it all morning and it seems to work 😅 I'm going to buy a new plage just in case that's the issue. Thanks fir replying and posting these useful videos
ruclips.net/video/eDmmN5jdGsg/видео.html right there!!!! This is the moment I've found out why my coffe maker wasn't working!!! I was trying to decal the machine without the cap holder and the reason it wasn't working was the magnetic sensor!! THANX!!!
Mine won't turn on? What do you think?
Check termal fuses on the thermoblock.
Thank you