you can see the islands by clicking the up or down arrow where it says suspended area. It will be highlighted in white and will disappear when you add a support.
Hi. Is it possible to set the focus of camera view where I want or is it only center build plate or center model? It is very annoying to support islands on a big model, when it not rotates around supported area.
Hi! Thank you for another great video! Do you mind sharing you ABS-Like Resin settings? I'm using Anycubic ABS-Like Resin+ with Elegoo Mars 4 Ultra, but I'm noticing that sometimes I lose very fine details in my prints.
I was watching your earlier support setting videos for Chitubox, and it looks like they've removed the ability to add more support profiles in 2.0. You've got the Light, Medium, Heavy and that's it. How have you been handling that? I've never used Chitubox before, but figured I would give it a shot.
Do you have a way to share your pre sets for the Sonic mini 8ks? I am still trying to figure out the settings. Last few prints I had a hard time getting the prints off the build plate and I tented up coming off in parts lol
@@wangdennys so I lowered it to 9s and it was still crazy hard to take them off. I’m using the aqua gray from phrozen. How is 9s too long? When I see everyone doing 20 seconds. Do you think I should try 5s burn in layer ? Or would that be a bad idea, maybe I’m doing something wrong
@@enigmaticreverieproduction5169 it seems your leveling is too low and compress the raft Hence the difficulty to remove. Relevel with thicker paper. And the paper should be able to be pull on each corner, but hard to push in.
Is that first stage lift distance of 1mm for ACF or nFEP? I have never tried anything less than 3mm first stage and 3mm second on my Saturn 2 using nFEP.
I don't like it so far. I use a resin that needs more supports (around 70 percent to 80 depending on the model) and I can't find a adjustment setting for the density.
Thanks for your input Dennys, You're still one of the best sources of information I trust. Keep it up Brother.
you can see the islands by clicking the up or down arrow where it says suspended area. It will be highlighted in white and will disappear when you add a support.
Love new UI. Its much more intuitive now. But performance... It not suppose to be slower than older tool.
It is beta afterall
Great Video. I appreciate your insight on the new version.
Enjoyed your rant 😹 thanks for another good video
LOL
Got a printer and started printing right as this version came out. Every video is in the older versions making the learning process very confusing.
Elephant foot compensation is a useful addition.
It already exist from previous version
Hi. Is it possible to set the focus of camera view where I want or is it only center build plate or center model? It is very annoying to support islands on a big model, when it not rotates around supported area.
Hi! Thank you for another great video! Do you mind sharing you ABS-Like Resin settings? I'm using Anycubic ABS-Like Resin+ with Elegoo Mars 4 Ultra, but I'm noticing that sometimes I lose very fine details in my prints.
I was watching your earlier support setting videos for Chitubox, and it looks like they've removed the ability to add more support profiles in 2.0. You've got the Light, Medium, Heavy and that's it. How have you been handling that? I've never used Chitubox before, but figured I would give it a shot.
My video was on pro
This 2.0 is basic, not pro.
Thanks for this insightful video
Do you have a way to share your pre sets for the Sonic mini 8ks? I am still trying to figure out the settings. Last few prints I had a hard time getting the prints off the build plate and I tented up coming off in parts lol
@@enigmaticreverieproduction5169 that means your bottom exposure too high. Lower it
@@wangdennys so I lowered it to 9s and it was still crazy hard to take them off. I’m using the aqua gray from phrozen. How is 9s too long? When I see everyone doing 20 seconds. Do you think I should try 5s burn in layer ? Or would that be a bad idea, maybe I’m doing something wrong
@@enigmaticreverieproduction5169 it seems your leveling is too low and compress the raft
Hence the difficulty to remove.
Relevel with thicker paper.
And the paper should be able to be pull on each corner, but hard to push in.
Is that first stage lift distance of 1mm for ACF or nFEP? I have never tried anything less than 3mm first stage and 3mm second on my Saturn 2 using nFEP.
1mm is fine on both acf and nfep
you will get faster print time
@@wangdennys well I've gotta do some testing then!
Is there a way to find somewhere the previous versions?
from the website
@@wangdennyswhich website?
i dont know now what settings use for my mars 4 ultra i want to use anycubc washable resin+..
Learn to calibrate your setting
It is the most essential step.
@@wangdennys hi do you know if the cone of calibration need supports?
@@patomaster95they do not, they should be printed as is
I don't like it so far. I use a resin that needs more supports (around 70 percent to 80 depending on the model) and I can't find a adjustment setting for the density.
All sliced files for my photon og are corrupted. Had to export projed and slice in 1.9.
photon og is too old i think.
@@wangdennys They listed it as supported.
Almost all software face such similar issue with old unit.
Even the same with smartphone.
You should report to the group.
It is still a beta afterall.
This or Lychee ?
Better try them all firstnl for yourself.
At least for this we got island detection for free
🤣