How to control DC motor with L298N driver and Arduino
HTML-код
- Опубликовано: 2 окт 2024
- This is the Arduino tutorial video to explain how you can run two DC motors and control the speed and direction using L298N Driver module with Arduino.
Buy L298n Driver module
bit.ly/L298N-Al...
Visit project page for wiring and Arduino code.
bit.ly/L298NDriver
bit.ly/L293D_A...
No need to request for like.......It's perfectly good video..... thankyou
I LOVE YOU SOOOOOOOOOOOOO MUCH, thank you sooo much!!!!!! I was trying to control stepper motor using L298n with nodumcu, my input was more than 12v and I forgot to remove the jumper your one tip made my day thank you soo, by the way your explanation was perfectly good you walk through every simple steps and I appreciate that. Thanks once again!
"Ground Should Be Common For 2 Power Supplies" this solved my biggest problem!!! ThankYou So Much 🎀
Hahha very funny
OMG. Your comment just saved my ass on this project I'm working on thank you so much! Also ofc the video was great too it's just I was being way too impatient and skipping through!
Brroo pls explain what you have commented here
@@kaviprakashv3241 the negative terminals of both devices should be connected to a single power source, such that the Arduino can send signals to motor driver.
If the negative of Arduino is not connected to motor driver then it's circuit would be called as an 'open circuit' in which no current travels.
Same problem,now solved
thank you for speaking english well understand always watching
Great, simple, easy to get and short..great work.
You can't go wrong with this thorough instruction...Thank You!
Hi, tnx for your awesome vid, I got a question, what is the minimum current required? I'm using two 9v batteries that are paralleled and yet it doesn't work (hardly moves)
Put the pins ,that he told in the video, back where it saya N1 N2 etc
Girl! This was so clear. Thank you so much.
Very nice video! In your video you used lower voltage to drive the motors. In my case, I want to use arduino+ L298N to control a 24V motor (full speed). How can I set up the connection to power the motor (preferably not using a breadboard)? Thanks!
awesome and precise!!! thanks, ma'am
thank you so much this actually helped a ton!!
Mam can I use this driver with 5v DC motors are they compatible with it please reply fast I need to do that for my project
Thanks its best totorial for testing l298n and arduino..
Thank you 💓,
LOVE FROM PAKISTAN 💕
Hi Fox 🦊
What about the 5v on the l298 where is it connected to on the arduino
Was struggling to do a project with motor drivers! and BOOM ....
Now iam able to complete my project as if it was a magic😉
Thank You soo much for ur fantastic video....
Really grateful to have ur video
you are mistaken at min-1.00, do correct it
Well Explained, nice video, I m using a 5v power bank as power supply, can I use it to power the motors, if yes where should I connect the +5v, the 7-35v pin or the 5v output pin
Power Bank => (+ve) terminal to lm298n's 12v (+ve) terminal and
Ground (-ve) should be common for both arduino and the shield you are using.
Lm298n => (+5v) terminal i.e Output 5V to (Vin) pin which is beside A0 pin on arduino.
Gnd Should be common on both power supply and arduino,
So just connect the power supply's GND to Shiels's GND and Arduino's GND pins
Nice Video ^^
" Whenever you use two power supply you have to make sure ground should be common for both "
I wanna marry you for this line.
Thanks a lot specially for this.
(I had a problem like touching the heat sink (that black metal) increases the power of motor)
honestly a great video i missed to connect arduinos GND to modules GND cause u i corrected my mistake now its working fine thank you mam for great video...
Hie mam it was wonderful tutorial I am using 2 batteries 9 volts but it is not following the programm it doesn't run anti clockwise
I LOVE YOU SO MUCH PLEASE UPLOAD MORE!!!! This Video was such a brilliant and perfect explanation without any fancy words and simple to follow instructions! Once again thank you so much :D
Thank you very much! I got all the information I was searching for quick and simple. Amazing video!
With the same motor driver i can only operate one motor...whenever i connect both motors it stops working....is it because i am using a 9 volt battery with the driver?cause individually they work with full power...what should i do?
Very good video ... But 1 question .....
I have L293D Motor driver ic instead of module.... And I don't know how to use it in the same way...
Can you please suggest me.?
l293d and l298n are same if u want to use it just search how to make a motordriver with l293d
Hello sister please explain with the code
thank you, very clear and helpful شكرا حزيلا
G8 instruction and project.
please make one video on bldc motor control
thank you for this video but If i want to run 4 wheel with L298N motor driver and arduino mega 2560 then how will i do connections
Maam please tell are u using an transmitter or remote how are u controlling it
Dear respected brother,
I am beginniner to use Arduino, sir i upload built-in led blink example sketch to Arduino uno and pro mini, both are blinking well, then I upload empty sketch to clear example code, system shows message that sketch upload done 100 %, but both boards runs previously blink example code. I tried to different systems (PC, Laptop,mobile) to clean an upload new sketch, but results are same, where I mistaken i don't understand. Pls help me to solve if you interested.
Interesting video. However, I noticed one motor was rotating from the code in the link, how can this be fixed so that both motors can rotate simultaneously ? Thank you!
I'm also stuck at the same thing...
I'm trying to verify the prob... nd one thing I noticed... the pin config of one of the motors is wrong in the given code....
The first two lines of the given code doesn't match with the description...
What if we used a motor driver shield. Do we still have to power the Arduino separately?
hia...if I were connecting 2 X 12V @ 0.1A brushless DC (PC) fans to this board, to power the fans and account for the 1.4V loss of power to the L298N transistors, would I be right in thinking I need to use a 13.4V (let's say) @ 2A power supply?
If I'm correct, will I then also have to remove the 5V output jumper as it's > 12V?
Never knew that was a stipulation regards the usage of the 5V output...is it documented anywhere?
Thanks for your vid and any feedback you may have 👍
I didn't liked but loved it
Thank you so much mam
Can i use 9volt battery to power this module with four motors?
THANKS A LOT, I HAD NO IDEA OF HOW TO REMOVE THE JUMPERS
Vo bhi diffrent speed par or anlog input se 4motor ki speed up kar sakte he
I desperately need help, both motors are connected to PWM pins but one motor spins faster than the other. I've tried many things and nothing works. Please help
I am using 9V battery to test the module the motors are running fine without the module but as soon as I give the Input pins (1,2,3,4) high then nothing happens so Is my L298 defective. Please help me out!!!!
My system is not working properly.I am using 9V battery and rf-500tb-12560 motor.Both motors are not starting simultaneously and one of the motor is not changing the direction of rotation.somebody please suggest remedy.
Thank you
My left ear enjoyed this video more than my right
Nice
You
Thanks for this video
I am stuck with self balancing robot motors not working kindly help.
i love speak hindi :D . Restart your computier :D
Thank you so much, i'm a total newbie to electronics, never heard of this bords before.
The end of my wires won’t fit in the power supply
Ma'am how to operate a higher rating motor to this driver module. As this support only 2 amp current and my requirement is to operate upto 10 amp. How to connect it with 10 amp relay.
@arun pal my requirement is same. Have you got any idea?
very nice explanation ,easy to understand for a newcomer.
Mine does not light up when i plug in positive negative but lights up from 5 volts of arduino pls help
(Im new and i have no idea what im doing pls help)
You didnt show bidirectional mevement. Is it possible to run motors in opposit directions?
What an awesome video.... Thanks a lot . you made my day. I was working on till 6 hours and i was just skipping but when i see your tutorial i got the thing❤️❤️❤️.... Thank you
please tell me ur circuit diagram
link in description is not working. can you semd the proper link?
What happens if we don't use common ground?
hi does anyone have idea what motor and tyer is she using
Can I use 10A current with l298n?
can i use standard 9v battery reply fast pls......
Awesome video
can i use this module with a pwm ouput for positional accuracy? basically, can i turn my gearbox DC motor into a servo?
Probably not
Please show me connect picture.....
Please show us how r u sending signal to the motor,
I mean it's through some mobile application or from
Laptop .
Please clear my dought
Signal is send by the Arduino after you upload the code to the board. You have a loop function (C++) usually where you call what motors should do.
Suddenly lost her voice just as I was paying attention to the next important part.
Plzz chare the same thing for other composent
Extremely amazing video. Keep it up!!
Thanks
I have 3 TB6612FNG motor driver. I am trying to connect 3 motor drivers to arduino. Which arduino should i use?
Also, can you help me out with something ? What power supply should I get ? Like what's the min and max voltage of the power supply ? Note : I want something powerful, if that matters!
if you are using more no. of motors , or a powerful motor , you should increase the voltage
How many voltage are u using? I tried mine but speed of the wheel is pretty slow and somehow only one wheel is working. Btw im using 6V connect both Arduino and driver
Can you help us for project
Why the second link cant be open ?
Great teaching ,thanks alot
did you use switch?
Can we use 4 motor on it for motor car
What l298n motor driver boost ampere
the code cant be accessed anymore
your website is not opening
can we activate the motors alternatively by using this circuit but different code?
Even after removing the jumper from the driver module it is not powering up I don't know what to do can anyone please help me out of this?
Hi ma’am, I have a doubt . I have a pump of 3.7v,0.1 A and can I connect that to this L298N .If so what are the changes or additional components required
Pump is - kamoer 3.7v 0.1A
Perfect, thank you
Motor are not working
I am using 3*18650(12.6) volt Do I have to open the jumper wire?
this is so confusing to me...
7.4 v lipo? is it shared between arduino board and motor driver?
yes, there is a 5v output on the board so im pretty sure... anyways do u know how to disconnect the jumper?
when i do same with 9v battery,sound is coming from motors but not rotating. help me with that
Coulter Mulvihill not sure
@Coulter Mulvihill if I had 2 X 12V @ 0.1A DC brushless PC fans to power, would I need to connect a 13.4V power supply to the L298N board?
I figure it would need to be 12V + (2 x 0.7V loss to the transistors on the L298N board)...although I'm by no means electronic literate and am therefore unsure as to what I'd need to do.
I'm guessing the Amperage would be largely irrelevant as as long as there were 2A provided it should all be ok, yah?
😅
Cheers for any help you may have
Hi. If i put the code on my arduino uno se directly, will the 2 wheels successfully move on forward and backward?
I just need the 2 wheels to control together with the arduino. TIA
Well explained
website is not working
Was very easy to follow.good instructions
Can you also do a tutorial on how to replicate a garage door operation with a single push button,that is forward,stop reverse?
Hard to understand her
What's the meaning of "ground should be common for both"?
Can i connect the motor directly to the 9v battery to test it?
You CAN connect, but DON'T, especially if your dc motor only needs 3.7V up to 6V. It will destroy your motor.
Can I use 2200mAh, 11.1v, 3c lipo battery
Please make 4WD ardiuno base car.. With bluetooth.. Please
I saw many videos but I did not understand a thing, but when I saw your video everything was clear. Thank you so much!!!!!!!!!!!!!!!!!!!!!.