How to control a DC motor with L298N driver and Arduino Uno
HTML-код
- Опубликовано: 29 сен 2024
- Welcome to the L298N Arduino tutorial. In this video, we are going to learn how to control a DC motor using an Arduino board. We are going to use a small and inexpensive module that features the L298N motor driver chip.
🛒 Arduino Uno ▶ educ8s.tv/part/...
🛒 L298N Driver ▶ educ8s.tv/part/...
🛒 2 DC Motors ▶ educ8s.tv/part/...
🛒 Battery Holder ▶ educ8s.tv/part/...
🛒 Wires ▶ educ8s.tv/part/...
💻 Code & Parts: educ8s.tv/cont...
Want to learn to program?
👨💻 Check my new RUclips channel: bit.ly/3tku2n0
🎮 My Android Game: bit.ly/QuizOfKn...
Short and to the point. Always a good combination. Μπράβο φίλε Νικόλα.
Motor will rotate once and then stop for 2seconds right not motor will rotate for 2 seconds 😅
My one motor is running but other motor is not running please help me it's very important to me
am facing the same problem now. did u figure it out?
Me too
Great project
If the 5V regulater is a LDO, then the power supply for the motor HAVE to be 6V or more
If the 5V regulater is a 7805, then the power supply for the motor HAVE to be 8V or more
Thanks for sharing :-)
ah thats why my motor is not turning, i am providing 5v supply and it doesn't work
now i get
Yay...My favorite Greek is back with a new vidoe!
Bro I am from India I can clearly understand that what u r explaining thanks for uploading this video ❤️
nice work bro and i learnt a lot of pretty other stuff and by the way love from INDIA
Thankyou sir , keep growing 👐🏼
can have a fall script please after add second montor ?
Hello Sir.
I like everything about this video. You doing well.
Canyou please give a solution
In this regard?
I am intrested how to change polarity of one coil with a speed of more than 100 per second.
I want to do a replica for magnetic train " Maglev ".
Thanks in advance👍
L293D engine hood problem. Output voltage in m4. 7 volts, and the rest of the outputs are 2 volts
I'm using a 6v battery holder, and everything works okay, but when I try to make the motor rotate backward, (in1 = low voltage; in2 = high voltage), the motor just doesn't rotate. Any reasons this might not be working? I did everything correctly in the tutorial. (Edit: This only happens on the output1 and 2 on the L298N, not output 3 and 4)
i tried to copy your code but it came out error
Tinkercad doesn’t have the L298N. It only has the h bridge and possibly other components used in the L298N. How do you build a L298N in Tinkercad that will support the code you provided for Arduino?
If i use 14 V batterie it can damage my 6 volt dc motors??? But I don’t want use the high speed, the half speed is enough
There is a problem when i compiling the coding in arduino... May i know why is that happened as i already followed the steps so may be the error lied on my coding and way to compile it?
Very good
OMG the best tutorial EVER about l298n!!!!
Why the wheels still can move even the usb cable did connect with laptop? I mean how you make it wireless?
I am using 4 motors with l289n but i am not able to set pwm below 128
Sir, I don't know why in mode max step, the motor will turn 4 rounds. Can u explain it? thank you so much
Would this work with 4AAs? I can’t get mine to work.
danke for your enlighting video, just one question: could i use the your approach on a vnh2sp30 or vnh5019 ???
thank you video very good I like
I will use code it and I develop it so as to make robot following program
This is good Detailed Info.So How can I control 4 Dc motors With This Process?
Nice work!! Good to see you back!! :-)
Hey, thanks! It is nice to see you around again! Stay safe!
@@Educ8s
hi , i tried to controll my motor with L298N and arduino nano , but my motor was not running . why it happened cause i checked the pins and program was also correct according with pin . but it doesn't work Can you help me please
First of all, thank you for this video. But I couldn't understand this. You said that if the motor controller has a 5-12V power input, the 5V pin works as output and provides 5V. But then you said that you connect the Vin port of the Arduino with the 5V port of the motor driver and the Arduino is fed with 7.5V. In this case, if I am not mistaken, there is 5V on the Vin pin of the Arduino, and this will negatively affect the operation of the Arduino in the long run? Am I right?
Thank You very much now I can complete my project for science fair now
THAAAAAAAAAAAANK YOU SO MUCH!!!! I finally could use DC mortor with this video!! THANK YOU!
Why are you removing the jumper between the enable pin and 5v? You can just drive the logic inputs with PWM signals. The way you're doing it saves a pin per motor, on the offset of only needing 1 PWM pin per motor.
VIN pin requires 6-20V but you are powering it with 5V only. Will this cause any side effects?
I am entering 7.5 V
The parts linked aren't working?
Sir what can we do using c language? Is it use to make for calculation or any other work? sir pls give your email address for any other information.
i dont have much idea but if you are intrested in robotics you can learn c++ its more easier to code in it
Can you do this with 4 wheels?
Extremely helpful! Thank you! the gem of the stop code made my project a succes
Looking forward to control hi amp dc motors such as 10 amps or more
Thank you! If I'm understanding this correctly, you are using your batteries to power the motor through the 12v+ pin and then outputting 5v through the 5v+ pin to power the arduino. Is it possible to plug in the arduino through the barrel connector and then use the 5v pin on the arduino to plug into the 12v+ pin on the motor and have the motor powered that way?
No you can't.
Great video! Well explained
I have three motors how to connect
How do I connect a switch to it ?
this is so informative ,thanks alot
thanks a lot, i was looking for this!
Love u bro❤❤❤❤❤
Πολυ καλώς. Συνεχισε έτσι
The best explanation anyone can find about how to use DC motors+ Arduino and L298N!!!!!
Thanks for the awesome comment! How is your OpenMV robot going ?
@@Educ8s I am working on it, my plan is to make the track (use a line following code) but I will put in the track also some Apriltags and then program different behaviors for the robot , the reason for that is the the camera has to be with an angle of 45 degrees, I wanted to train a network with tensorflow lite but the 45 degree constrain is a limitation for that. I really admire what you do.
Good job!
excellent...
Then what should I put in void loop
The thing that you want to repeat for ever.
Extremely helpful! Thank you!
You are perfect!
Keep it up🎉
thank you
Great tutorial; for next one put encoders on the wheels.
Noted!
what about a setup with 4 motors?
Use two modules
Thank you maaan
I hope you took away lots from this video. Let me know below!
PS. Do you like quiz games? Check my popular FREE Android quiz game here: bit.ly/QuizOfKnowledge
I've watched dozens of videos these few days. And this one worked for me. Thanks.
I am glad it works!
Can i do this with a relay?
Can i get the coding?
Check the video description.