Reasons why water can not dispense while mopping
HTML-код
- Опубликовано: 6 окт 2024
- If your Ecovacs deebot or Ozmo series model can not dispense water while mopping so what are the expected reasons & how we can prevent from them.Detail introduction of Ozmo water pump function. How it works.
#Ecovacs #ozmo #Deeot #water issue #water can not dispense #why no water while moping #water tank #Detol #detergent #liquid detergent #floor cleaner
hi thanks for the video, it is a very good explanation about the reasons, but what to do when the detergent was used by mistake and now the water is not coming out while mopping? please give an advise! deebot ozmo 610
Great videos, you explain the stuff so well. Please keep sharing your knowledge, most definitely required during this pandemic as it will help us with the first level diagnosis of issues before we can even call up the service centre. 👍👍
Welcome
Thanks to this clip, my Ozmo 610 already dispensed water again. ❤️❤️❤️
Thank you for your videos. They are very useful. I have a deebot u2 pro and the water flow is very high. I have checked the water flow setting on the app and it's set on standard.
Hi...thanks for watching...in u2 pro full water tank can be finish in 60 minutes its fixed. We can not select from the app...its normal
Good Evening Sir..Great to have the video, really appreciate your kind effort. I'm facing the same problem to my DEEBOT DD3G. I'd try many times to find out the problem until I get this video as same model to mine. I'm not sure what's the problem to my robot. Humble request to have your kind advise to us..Thanks lot..🙏🙏🙏
If u r in Malaysia plz send ur deebot to our Ecovacs service center by courier... Plz write ur name Contact no courier address n what's the issue on a paper n attach with deebot or u can whatsapp at 00601137973018
how to remove the blockage to due detergents
Very useful information
Hi, thank you for the video, very clear.I have T8+ with two water tank, the ozmo pro and the normal one (with washable pad). Now the issue is that with ozmo pro it is all working, but with the normal tank the pad is not mopping, it is dry and water do not mop it. I think it is not a problem of the deebot pump (because it does work with the ozmo pro tank), how could I check the issue on the water tank side? thank you so much
Hi, im from colombia in south America. Very nice video. I have a Osmo 930 and i have one problem. When i put the water tank i can hear the sopund that is ready to mop. buen then the robot start and make some circles and stop and try to return to the charge base. If i remove the water tank the robot works fine. Any advice?
If without moping plate deebot functions normal but after installing plate doesn't work n stop after few seconds then there will be 2 possible reasons: 1 both wheels rubber grip spoil & became flate thats why it can not move forward while moping. If u think tyres got grip in good condition then 2 reason is moping cloth...try another moping cloth. If moping cloth very rough n thread comes out then deebot wont move sometimes
Thanks for the video, very informative. Using floor cleaner seems to be a common mistake, shame the manufacturer doesn't think to apply a sticker to the tank saying "DO NOT USE FLOOR CLEANER, WATER ONLY", that may save a lot of us making the mistake. I have a Deebot T9+ & used pine-o-clean and now it doesn't work. Is this something I can take apart and try to fix at home or should I return it for repairs? Prior to this we were extremely happy with both the vac & the mop, it has exceeded our expectations.
U mean water not Dispensing from Ozmo pro tank or its not ascallate ???
@@ecovacstechnicalsupport5278 water does not dispense
Can WhatsApp at 01137973018..a video clip so can confirm what's the issue
@@ecovacstechnicalsupport5278 Sorry, I don't have WhatsApp. The issue is I used a floor detergent and now Deebot mops like it should except no water disperses from the tank, it just does a dry run. I assume the tubes are blocked as you have shown on your videos. My question is, is this something I can try to fix at home or should I take it back to the store of purchase for repairs?
Actually need to dissemble the deebot so can test weather water pump disconnected or just water pipe block...
Hi,
Today I, received a Ozmo 930.
Resale version. Shouldn't have issues but unfortunately there was no water coming out as told in this video.
I checked the outside parts but didn't see something wrong.
Thought maybe the pump is dry.
Sp decided to put a Syringe (10cc medical injection) with some silicon hose on it. (end little bit tight up with wire) placed it over the intake nozzle and pushed water through.
Had some resistance but pushed gently through until something felt like opening/popping. Directly after the 3 nozzles starting to flow water out of it.
So also probably clogged or sticked tubes/pump.
Maybe it helps others.
Now working fine but keeping an eye on it. Luckily the pump or maybe only a motor is not an expensive part to replace and handy enough to do it myself.
And if not allowed to put cleaning dissolve in just wash the mop before and put some detergent on it. That's enough for one clean. Better than nothing.
Thanks for sharing 😊
I have a u2 pro it's dispensing lot of water on the floor and slipping on the floor as well. What do I do !!
Hi, I am having the same problem with my U2 pro. Couldn't find out how to solve it! Now i am not putting water in its tank, just sprinkling little water on floor so that the cleaning pad absorbs it and does not have excess water spilled from deebot. This trick seems to be working ok for me
However if anyone knows how to solve this water overflow and skidding of robovac problem then i would definitely like to know!
i have a ECOVACS X1 OMNI. the water will dispense properly from the start and slowly the water to dispense very less.
How to solve the problem if mopping outlets are blocked?. Buy a new container?
If u use only Water then it won't block but it's ok. There's nothing impossible...I have solution for all issues...u can use normal needle or 💉 n try to clean from outside normally it starts working again if pump not spoil or the whole pipeline not block...if u can manage to open that Mop plate located underneath the dust box area then can easily open that pipe line it works if all clear
Hi thks for the video. Could you please share how to check the pump DIY for my deebot ozmo 950 series? There are 6 little holes in the deebot body that mopping plate is installed. Can it be cleaned using a WD40 contact cleaner or just needle?
Hi, good sharing. Can you advise air pump of what model can be used by Model DN 320 (China model)? Thanks
Any advice for when it is not working but you have only used water? We have not used any detergent and no water is coming out.
Good question...ok for testing plz remove moping cloth...make sure water tank full with water.. moping plate attached... remove water tank n plate together.... power on the deebot..once ready to use then attach water tank n plate without cloth together see weather deebot gives voice indication that moping plate has been installed???...if got msg then press water tank from back tightly n hold then pres auto button see water can dispense or not...if can then just water tank issue.. became slightly loosen from lock so need to replace tank only...if still no water then water Pump Issue... need to replace...but you plz check my other water pump issue videos as well... sometimes just pipe Tangled that's why water couldn't come...like this u can try at home first
Ok so I have been using dental in my deebot and it's clogged, is there any diy things I can do to fix it myself?
Hi... I didn't understand ur question witch thing clogged... Or u can whatsapp a video clip at 00601137973018
My robot is just circling around the space spot while mopping, sweeping is done fine but mopping it's not doing a good job since a month
While vacuuming deebot moves smooth n straight?? But while using moping function it doesn't move straight???
Hi, I use a Ozmo T8 with pro attachment. After a recent mopping operation I found little bit of water inside the dust bin and the dusbin compartment. The quantity was very little. Both the filter and the sponge were dry. What could be the reason? Is it something I should be worried about?
I sometimes see this with non-pro attachment. I think it happens from the robot going over the same area again when it’s still wet, so it sucks up some drops.
Im using Ozmo 610, how if the water really get block? Any idea to fix it?
Plz follow the instruction of the video if everything is ok but still water can not dispense then 3 reasons...1 maybe plate sensor spoil witch detects that mopping plate installed or not. 2: water pump volve block 3: water pump spoil... in all these 3 issues..you must send ur deebot to service center...or if u can buy water pump only then u can sattle at home...pump in Malaysia is 65 RM
Hi how can i clean water system from dettol please? On the ozmo 950
Actually water tank can not clean or wash from indide....it can spoil
Hi my T8 deebot is leaving dirty streaks while mopping. Please advise how to fix. It's only 2 weeks old
May i know that after moping how's the moping cloth condition??? Is it very dirty??? Dust stick with it???or no dust just quite clean ??
@@ecovacstechnicalsupport5278 it is very dirty but not everywhere. Only in the front
Hi as you know to keep house safe from corona we have to use disinfectant .is there any special disinfection for reboot mopping or any other way to use disinfectant example adding on floor or on the cloth etc..
I sometimes add some directly to the cloth, and I haven’t had any problem. It cannot get clogged that way.
What should I do if the magnet is rusted? Is there any easy ways to replace it?
Rusty magnet also works perfectly just use WD-40 to clean the rust...if it's totally damage then plz find tiny magnetic piece & stick at same place...can use something to stick like hot glue etc..
My ozmo 950 not dispensing water. In fact it climbed on carpet also.. same was as it would do when water tank is not attached. So I feel it is not sensing water tank only
After power on the deebot plz attach water tank with mop plate together see weather deebot gives msg that Moping plate has been installed or not...if got msg n deebot still enter in carpet area means carpet sensor faulty...located next to charging connector in whole...just replace that will be ok
Thanks for your reply...i actually repaired the main brush motor by watching your video. That main brush motor issue is solved and thanks for the same. I have done some mistake in assembling it back and after that the water dispensing has stopped..it does not look like carpet sensor issue as water is also not dispensing
I have deboot u2 pro…… it is dispensing more water while mopping……can u please help in rectifying the problem
Hi..I have water dispensing problem for OSMO 950..I am using only water since I purchased it 6months ago. but last 2 weeks it stopped dispensing water. Pl suggest how to fix this?
After deebot turn on attach mopping plate..there should be a voice message that moping plate has been installed....if u didn't here this message means moping plate sensor not functioning. If u hear this sound then water tank issue needvto replace water tank...water pump in this model is very good quality one...wint spoil so fast...so its just water tank issue
1 thing u can try at home is...on top of water tank u can see black circle got 4 white dots on it...use a needle n pop in 4 white dots so air pressure increase then hopefully it start functioning again
@@ecovacstechnicalsupport5278 do I need to insert needle in those white dots? can you explain what I need to do?
I am not sure if my new T8 is working properly. I wash and wring dry the mop cloth, then set the mopping function to ultra high level water. But the floor is only a little bit wet. I never use detergent in the water tank. Can you help?
Ok noted...in this case if you want to test that how much the water dispense. Plz power off the deebot n turn on again once deebot ready to use then remove moping cloth from plate fill up the water tank to full. Attach moping plate with water tank without cloth. Insert water tank to deebot make sure u heard the sound that moping plate has been installed...if no sound then moping plate sensor not functioning. If got sound then just press auto button then u can see how is the water level bcoz all water will drop direct on the floor you can see on floor once deebot start moving.
One more thing i let u know once u press auto button same time water start dripping for continuous 3 seconds then stop and after every 90 seconds will drip again for 3 seconds
@@ecovacstechnicalsupport5278
Tried the solution suggested, the water is dispensed like you described, continuous water dispensing for short while , stops for a longer period and repeat again. Thanks a lot for detailed explanation and advice on how to test.
Welcome
@@ecovacstechnicalsupport5278 I just bought my T8 and the mopping seem not functioning. I have tried the suggested solutions but there is no water came out, any futher action i can do. Or should i just send to the service center?
Can you explain how to remove the black panel after the pump please?
Need to remove vacuum fan then.. remove tiny screw if got on that black plate...then use screw driver to pull up that part
Hi From water tank reservoir our inlet pipe came out... can we open the reservoir and fix it?
Actually some customers they shake the water tank with water inside to clean inside... But in result water pipe disconnect when water hit the pipe... N water tank is sealed from top... Means if any part disconnect inside we can not open n repair that part... Only solution is to replace tank..
💫💫💫💫💫
Sir, for I life V5x water is not coming whenever the rubber closure is fitted
U can send me a video clip of vacuum at 00601137973018
How to clean Dettol or detergent from the water tank
Detol signe can not remove but detergent can remove with hot water...but don't shake tank else pipe Will disconnect then need to replace water tank...just leave hot water for few minutes then just gently turn ... detergent will comes out
My robot vacuum says, "Please insert water tank and restart." I've inserted the mop bracket and tank but when I start the machine it still says please install water tank. Do u know what possibly could be the issue?
Same problem😢
I've just had to live without the mop option
Hi, how about the same problem water not coming out with deebot T8?
In T8 water pump is different more powerful won't spoil fast... U can try an other water tank....hopefully problem will be solve ....before buying plz get help from someone who's using ozmo 920, 950, t8, T8aivi, T8plus T9 or N8 pro.... All these water tank is same... So just borrow for a while n test if water can dispens with this tank then just replaced new tank... Or can contact nearest service center for this help
@@ecovacstechnicalsupport5278 i switched to ozmo pro, and the water can dispens, so is there a problem with my deebot T8 normal water tank? should i change my water tank? or is there anything i can do to troubleshoot my normal water tank ? like maybe make a hole on top of my water tank ?
I have used Dettol, mopping not working n i came to know after 10 days what to do know
Mine is mi robo vaccum cleaner
@@superstylishnamrata8359 did u find the solution
I am facing same issue
Hi we have deebot u2 pro. It was working fine but from past few days it's not using water when mopping and it ends up leaving wheel marks and also does not vaccum like before. I do clean the parts as recommended. Please suggest how to go about. I tried calling customer care but it always says customer rep busy. Please help.
Hi can u plz whatsapp me a small video clip so I can confirm what's the issue 00601137973018
@@ecovacstechnicalsupport5278 hi..I have deboot 950 ozmo series..water not dispensing..voice msg comes when installed..never used any liquid cleaner..just water..not sure what issue is
Hi, I guess I used some detergent so I blocked it, how can I solve?
Water pump normally we replace then should be ok
@@ecovacstechnicalsupport5278 great work guys! Thanks!
I have haeir vacuum cleaner and it's wet mop is not working...water not dispens
Basic method is same in all models....
@@ecovacstechnicalsupport5278 but I've tried to open it but it's not opening...can I whatsapp you ?
Hi my Deebot is not dispensing water from the water tank . When pressing on the plastic button in the water tank , one or two drops of water are only coming out . Is that normal ? Or should more water come? I have tried making a hole on the 4 small circles like you suggested in the previous comment but it is still not dispensing water . When pressing on the button in the water tank , the pipe inside does not move or do anything ? What is the problem here ? Is it the water tank or something inside the robot ?
When u attach moping plate...do u hear any msg fron deebot that moping plate has been installed???
If u heard this msg then might be water tank or water pump issue...but in both situations u need to contact with service center in new New Delhi
@@ecovacstechnicalsupport5278 yes the mopping plate is attached sound is coming . It is the pump or tank issue .
If u can hear the msg that moping plate has been installed means sensors working. Only water tank might be not connected fully a bit loose that's why pump couldn't build up enough suction to pickup the water from tank .. or water pump itself not functioning...without installing new water tank we can not confrm...or if any of ur friends using. 920, 950, t8, t8 aivi, t8 plus, t9 then u can try their water tank to confrm weather its just a water tank issue...because in all above model water tank & pump is same
@@ecovacstechnicalsupport5278 I have a Ozmo 950 . In Amazon the water tank of T8 is only available . So can I buy the T8 water tank for 950 ? Will it fit ?
My T 9 came White this:
Reservoir is stuck.... And stop clearing
There come wather out on the mopp
Hello
Doesn't say how to fix.
Some other videos already uploaded about this topic sir
English!
Hi thks for the video. Could you please share how to check the pump DIY for my deebot ozmo 950 series? There are 6 little holes in the deebot body that mopping plate is installed. Can it be cleaned using a WD40 contact cleaner or just needle?
Actually it's very rare that water hole block that's why water not drip... Normally in ozmo 950 few things need to check.. Water tank, when attach mopping plate so got voice message that water tank has been installed?? If not then mop sensor faulty.. If got then water tank or might be water pump is faulty
When the water tank inserted, there is a voice message water tank has been installed. If it is a pump failure, how can I check and fix it?