Are you sure you’re using your power tools safely? Avoid the most common (and dangerous) mistakes! Get your FREE guide here 👉 bit.ly/10PowerToolMistakes
I’m a carpenter. This man is the one to watch for real knowledge. I even enjoy the videos about things I’m already familiar with. A great ambassador for our profession.
I've been a woodworker for 50 years and in construction for 40. I probably didn't learn much from your video but I pretty much agree with everything you presented. Well done, excellent video.
Agreed. Speaking for myself I learned from experience and wish I had these passed to me years ago. So if you're a yungsta, pay attention. These tips will become second nature, but having them listed is very, very worthwhile.
"I probably didn't learn much from your video"... the fact that you learned anything from this video means you are a bad woodworker. i'm not a wood worker and i learned nothing, every tip in this video is completely obvious to me and that makes you look bad im"h"o
Additional metal drilling tips: Center punch where you want your hole to prevent wandering (same as you would for wood drilling). Add a drop of lubricating oil to the tip to cool and lubricate the cutting surface. After the hole is cut, use a larger bit spinning in reverse to slightly touch the hole to knock off sharp edges.
Solid advice! As a handy guy, I'm learning from all his vids and comments I read that just KNOWING what tradesmen do can take hours off a project by increasing precision or choosing a non-favorite tool.
Number 1 sharp suitable drill bits, the angle of a wood bit at the tip is more acute. 2 suitable speed for material and bit type. Almost every woodworker I have ever seen, particularly on RUclips uses spade/ flat bits way too slow, they work best sharp and fast. 3 Use suitable machine !!
I liked the video. No one in my family ever used a drill themselves. Now i am thinking of getting one and trying to do things myself. Thanks a very informative video.
Great tips. I think I have done every one of these at some point. One I would definitely add is adding oil when drilling metal. It helps the cutting, keeps the drill sharper and helps cool the bit and material.
Super helpful!!! Single mom starting over in my late 30s. This was clear, concise, & i saw another comment from a vetran carpenter of 40/50 years validating your recommendations. Honestly, that means a lot to me as often the video will say one thing and then the comments in the bottom just say how wrong the recommendations are which is very confusing to me who has minimal experience. Thank you again so much! Definitely subscribing!
When I use tape for depth drilling, I make a little flag. Then when I get to the proper depth the flag swipes away the sawdust and you know you are done. This helps eliminate drill depth creep (by pushing on the tape) if you are drilling multiple holes.
Exactly! And ... I like to draw a small skull and cross-bones on the tape flag. This doesn't improve the drilling process any. However, it allows me to pretend that I am the captain of a pirate ship, and thus, my workday goes by much faster. I literally sail through my workdays. 🤪
Ive done this for alongtime when using a hilti hammer drill for drilling concrete. I use a piece of red duct tape bc the depth measure on them move in time. Crappy design. so if any inspectors are walking through they see i have it set for depth. They just walk by bc they know im the sht. Lol
Hi Gloria 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
Holy cow. What an unreal amount of useful info! You even crammed extra tips into several of the tips lol. Great stuff, thanks man, so glad to have recently found this channel
adding to the vid, putting a piece of wood underneath the piece you're drilling into will also help prevent tear out. Other than that, well paced and informative video. Thank you.
I found that out by accident. Spade bits are notorious for tear out. So far..I have not had any problems. I try always put a small piece of board underneath. So far ..so 👍
So far so good.. The 2 boards should be clamped togother if possible..time permitting ..and other factors...going slow or. A marker tape for depth are choices. Oh yeah..years ago I bought a 50s hand brace..geared, and good quality wood handle. They built ships and houses out of them. I am old school. Sometimes I like to do something totally using hand tools.
Can you cover how to drill into concrete and installing concrete screws? My concrete screws seem to pull out too easy because the hole i drilled is too large. I'm using the correct size and type of drill bit. I suspect my cheap hammer drill is not spinning the bit true, but is wobbling the bit which causes the hole to enlarge.
I liked this video. I've been a carpenter for 30 years and never heard of swarf. One tip that you left out that I like is when drilling with a spade bit or hole saw only drill until the point on the bit comes out then flip the wood over and drill the rest of the hole to prevent tear out. Keep making great videos!
Thank you so much for your tips. As a single woman, I need to do what I need to do to get by. This bit (no pun intended) of information is extremely helpful.
Great video. One major tip I would add is to make sure you're using the right drill bit for the material. Bits for masonry vs wood vs metal and even ceramics make a huge difference.
Thank you so much for making this video! I have had no training whatsoever, but have been building stuff for quite a few years, something I enjoy doing. However, I have had a lot of problems with drilling in the past. These tips were very helpful. A few of the things I had figured out to do on my own, but didn't know most of them. Can't wait to go drill using these new tips!
Hi American girl 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
It's a good idea to use a coolant when drilling metal. This will extend the life of your bit before it gets dull. Even a light oil like wd40 is better than nothing.
Great description of techniques, # 12 could be to apply a backer block (clamped or flat on the table) to avoid tear-out on the back surface of the work piece.
Great basic review. Glad to see I'm already using all those techniques. With regard to the painters tape, giving yourself a little extra wiggle room and not going to the depth of the tape is key when doing many holes; 1, 2, or a few probably won't be an issue, but the 144 I did for making a 6 hole adjustment for 6 shelves...the tape wears quickly. I also wind the tape counte to the spin so if the tape does touch the surface it doesn't unwind. I also use a long length of tape to give you more "bulk" at the stop point and fold the last half inch into a little flat so you're not only more likely to see when you're getting to close to the surface, i.e. drilling too deep, but it also makes it much easier to have the flap for unwinding it from the bit when you're done.
Thanks for the MANY valuable tips for drilling, etc for DIYers. Some knew about before, but others that I will apply. Looking forward to your next video.
Hi Susannah 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
I always watch ‘Basic’ videos. Amazing how much I’ve learned by not thinking I know it all. You offer quick and precise instruction. Cannot thank you enough!
Thank you for all your videos. I was trying to make simple plant stand and a bench. They are ridiculously expensive in store. I was inimidated by the amount of tool I needed for making stuff. When I came across your channel, I knew I can get away with 2 tools. Thank you for being honest.
Thank you for such clear and concise bunch of VERY useful tips! I’ve made a few blunders lately despite years of experience so it’s never too late to sharpen up the skills.
To avoid tear out I have used tape as well but I prefer to clamp a piece of waste stock to the side where my drill bit will make its exit. I can always find a big enough piece of scrap wood to cover all the area where I am drilling holes to prevent tear out. When I use hole saws or spade bits. Having scrap on one side is a big help but mostly I drill a smaller hole through my project first. Then use the spade bit or hole saw and just penetrate the wood on the one side part way in. Then drill through from the other side all the way using the small hole that is showing as my start point. That way you avoid making a messy tear out because the surface of the wood on both sides has been cut with no cutting tool that has broken through. I always keep in mind that some woods are more prone to splintering than others.
Tip #12....When building a project, use two electric drill motors. I do that all the time. It saves time from changing drill bits. I have already used three electric drills, one had a power cord since I don't collect drills. Great video, all good tips. Barry
As a DIYer I really have enjoyed all of your videos amongst the many that I watch. Thank you for being dedicated to your trade and teaching it to others. Awesome stuff.👍🏽
Do I need the hammer function turned on for the second (or third) size up on concrete wall? Because I live in an apartment, so I try to drill as least as possible and those hammer drills can get very LOUD, lol.
@@cynicalheis You have to use a hammer drill with a masonry bit when drilling concrete. Concrete is way too tough and hard for normal drills and just rotary drilling.
@berndeikers8924 they do, but from my experience, someone always loses it, lol. Whatever way works, I suppose, because there's a few ways to get it done
1) use your drill’s clutch to select the right speed for the job. there’s also usually a high and low gear (or 1 and 2). your low gear delivers more torque at the cost of rpms 2) hogging material can snap a bit quickly. your bit will often discolor at a stress point from heat before it breaks. also wear eye protection 3) obviously dont drill through a workpiece into anything that’ll damage the bit. or into anything that cant be damaged
Remember, when you’re clearing out swarf (I love that word) with your finger, be careful that the bit isn’t hot, or you could burn your finger (ask me how I know this).
You ain't the only one. If the bit is tiny, dad flicks the end of it. Usually the little bit of flex and rebound is enough to bounce out the swarf. My fingernails are always uneven lengths; I just use whichever one is long to clear out the swarf. I love that word too. :)
Great tips as always - I used coloured tape matching the rawlplug colour and depth on my masonry bits so they are ready to go, and easy to identify at a glance which plug goes with which drill.
Hi to mrJD - Liking the idea of coloured tape matching the rawlplug colour. That is one hell of a good tip. Ain't gonna forget that one. Thanks goes to The Honest Carpenter for creating this platform. Cheers and happy drilling !!!
Thanks for tips, Ethan. I wish I watched this before recently drilling into metal studs to install toggle bolts. It seemed to take forever. On the bright side, I somehow figured out that I had to step up drill bit sizes for each hole. Seeing this approach confirmed in the video makes me feel a bit handy-dandy 👍🏽
Thank you so much for teaching me so many tips & tricks as well as showing me what tools and brands I need to buy. After 43 years of a happy marriage, my husband passed away last September leaving me to care for this property all by myself. At age 66, I'm now all alone and trying to learn what I need to know so I can make it on my own. Thanks for helping me learn the skills and products I need to repair my home.
Hi Carol 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
About 50 years ago when I was in wood shop class my teacher told us students the best way to select a drill bit for a pilot hole. He instructed that we take the fastener we want to use and using a drill index to find the hole that the fastener will fit into. Then we were to back off two drill bit sizes and use that size bit to drill our pilot hole. It seems to have worked nicely for most holes, but occasionally when drilling metal, or very hard wood, only back off one drill bit size.
found a drill bit hole sizes template (13 hole sizes: 1/16"-1/4"), test the screw on a hole where it goes through and pick a drill bit 1 hole size smaller for hardwood, 2 hole sizes smaller for softwood
@@torTxoFognaTuluZ mastercraft hammer drill - included in the set of drill and screw driver bits (labeled as 'drill gauge'). it's 3x8 cm, made of plastic
Very helpful to dyi’ers, especially those of us who weren’t allowed to take shop decades ago (because I was a girl). I’ve figured out most of this on my own as I love rehabbing homes for myself and my friends. Your video would have been great back when I had to figure out what I was doing wrong; now looking for instruction on what all the fancy drill bits are supposed to be used for as I have a number of them that came in a huge set but they don’t tell you what they do or in which applications they should be used. Thanks for the clear instructions!
Hi Stephanie 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
Great tips. Some I figured out on my own, like using tape for a depth gauge and others, like using an awl to make an indentation before drilling, I learned from my mom. Here are some of my tips. (1) Look at your drill bit when it's running. If it looks blurry, then the drill is bent, or it is not centered in the 3 jaws, or it is loose. (2) When you are tightening the jaws with a key, start in hole 1 and give a little twist to the key, then go to hole 2 and give a little twist, then go to hole 3 and give a little twist. Then repeat 1-2-3 until the jaws are tight. By moving from hole to hole in a circle to tighten the jaws, you keep the drill centered in the jaws. (3) When inserting a small drill, like a 1/16 or 5/64, start with the jaws closed. Then gradually open the jaws until you have just enough of an opening to insert the drill and tighten. That will insure that the small drill is centered between the jaws. Always wear eye protection when using a drill.
If you're drilling with a fine bit and it snaps and you don't have a spare, grab a nail of the diameter, snip off the head and use the nail as a drill bit. It's not perfect but can get you out of a tight spot.
Another great tip Maxx. I’ve got a certain way of cutting then to get kind of a chisel point out at the end. Have definitely used that trick more than once
Been there done that..the fine brass looking ones that come in a blister pack (read cheap), break super easy. It just occurred to me. If you are not making progress with the bit..put it in vice or clamp. the nail to a table..then file cross hatches or just basically rough the tip area of nail up. Never tried it ..btw..I am in the process of putting brushes etc in my 30 year old Ryobi hammer drill. It has been put though the.ringer..
I agree with you on the "punch" thing! It can be really annoying when the bit wanders around on the surface on it own. Sometimes you don't have something to punch the surface with though. What I do is I place the bit where I want it, then I place my offhand on the back of the motor casing, above the drill grip. I then apply pressure, and give a short, quick pull on the trigger. Makes sure to do it fast, so the bit stays in place. Another method I found is taking the right size bit, or a bit smaller than it, and grab it in your hand, and twist it side to side, making a little indent in the surface your drilling. This effectively does the same thing as a punch, but it may not go as deep.
Great Video! Recently found your channel so a new sub here. One tip that I like for finding the right size drill bit to use to pre-drill for a screw is to use the drill index. Find a drill bit that the screw will just fit into easily then go down two to steps smaller from that drill bit size. You can vary the number steps for softer or harder woods.
A tip for masonry, that I learnt recently Make sure that the masonry drill bit is all the way to the back of the hammer drill/ drill hammer setting. Thanks for sharing these useful tips, some I knew some I find not
Great video, lots of good info. One thing I discovered: I bought 10 packs of cobalt bits on line, of the most popular sizes that I often wear out or break; 1/8 and 1/4. Not too expensive, and cobalt bits are excellent!
I think for diy and beginners a pocket hole jig for angles and a stop collar for depth would be a good investment. Good tips though. Even old dogs need to see if there are any new tricks out there. Keep up the great work with concise to the point videos. 😎
With the tape on the bit method, another good trick is to leave a flap of excess tape folded onto itself. This serves to sweep away saw dust from the surface being drilled once you’ve reached to prescribed depth without you having to peer down at the work so closely.
I've commented before; but that Hitachi drill is the shiz! I've had one for years now. It's been my favorite by far. Really cool tip see someone else with one! 👍🏼👍🏼
I was able to screw half a screw to prop up a fallen picket, and gave up. After watching your videos on fasteners (love learning new words) I purchased exactly what is required for this very tiny job, and hope to complete it on my day off. Thank you for the lessons 🖖
Hi Sandy 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
Just got my first brad point drilll bit set, and it makes precise holes in soft woods go much faster. Let's you drill a nice clean hole exactly where you want with a single step. No need to punch or tape., but it is another set of bits to keep track of, of course.
Also, get some bees wax or a bar of soap to apply to your threads before inserting the screw, especially in hardwoods. This will make the screws go in so much easier. P.S. If you are doing a lot of toenail screwing then get a Kreg jig (I know, this is not a simple screw technique but wanted to throw this in).
I've been trying to drill the mushroom rivets open on my hotwheels madpropz, but i couldn't figure out why it wasnt working, until you said that i should drill slowly. The mushroom rivets on every hotwheels is made of metal, and your tip worked wonders, i managed to drill a hole
Hi Brenda 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
Great tips. Drilling on angle! I like to wrap my tape around but also making a blade with the tape so when drilling the blade will clear away the debri!
I am loving your channel. I just bought a house and I'm trying to save money by learning to do things myself. You have helped me a lot. Which of course saved me a lot of money. Thank you!
Some stores will markdowns wood up to 70%..I recently found.out that slightly defective boards etc can qualify. Just ask ..it doesnt hurt anything. Stores actually benefit from this..it saves them from.having shoddy stock and taking the time to cull lumber.or.any other.product. I use old pallets to hold things..of course safety is always your.first concern.
Hi Lesley 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
Thanks man. Learned a lot and confirmed a few lessons that I’ve learned myself the hard way. For plasterboard fasteners I keep an old bit of plasterboard in my garage so you can practice and see what’s happening before drilling the walls in my home. 👍
All the new terms I discovered: swarfing, hogging out, toenailing... and also how come I keep breaking drill bits. Thank you for this! I learned a lot.
There are a few reasons why drill bits break when I'm using them. 1. I'm pushing to hard 2. Drill bit caught on a harder material while drilling into a hole. Example: Drilling into wood and you hit metal. The drill bit catches on the metal and breaks. 3. Cheap drill bits. Always buy good drill bits. For most DIYers and Contractors HSS drill bits will work just fine. HSS stand for "High Speed Steel." These are drill bit that have been heat treated to increase the hardness of the drill bit. 4. Drill bits typically go on sale: Christmas, Father's day, Memorial Day, 4th of July, Labor day. However, I find quality drill bits at their lowest price during the Christmas shopping season in the "stocking stuffers isle" or on Father's day. The big box stores put them out as their loss leader and you can typically get them for about 40-50% off. 5. Last but not least. Always wear safety glasses.
Bits break often for three main reasons: -pushing too hard (small bits flex) -change of direction 1/2 way through hole -cheaply made bits (bad temper on bits)
Hi Bonnie 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
Thanks! I now have to salvage my project. Drilling fast takes confidence so I think it's wise to test on a piece of scrap wood. I also have a problem to drill straight for my dowels.
To help drill straight vertically. Fix together two pieces of wood to form a L shape about half the height of the bit your using. Then place the bit where you want to drill,and then place the L shape piece up against the bit where the corners meet. Then drill; it will not be 100%,but much better then trying to drill free handed. Also to drill a straight hole horizontally; you could do the same thing,but it can be cumbersome. I saw a trick on "Wood by Wright" where you place a cheap ring,key ring,or perhaps even a washer onto the drill bit itself so it can spin freely; then place the bit where you want to drill,and place the ring about middle way of the bit then drill your hole. An if you tilt the drill up to much the ring will slide towards your work,and if you tilt the drill down to low the ring will slide toward your drill. I realize the last tip sounds like a lot,but once you try it you be like oh okay piece of cake. LoL Hope this helps.
@@davogifman542 Can you show a photo of how this is set up. Also, looking for something like the wolfcraft fowl jig listed below in the US. Thanks so much.
@@liamofthornhill Can you tell me what a cheap comparable jig would be Amazon US? I'm putting together a bed frame with 2" x 2" poplar hardwood with a butt joint, and I think it will be hard to make straight holes. Thanks.
@@barbarakaimowitz9138 www.ebay.com/itm/Handheld-Woodworking-Doweling-Jig-Drill-Guide-Wood-Dowel-Drilling-Hole-Saw-Kit-/224246369046 I'm in the uk but eBay is a good try
Thank you so much I was looking everywhere for "why won't my drill bit cut through hardware" when all along I just needed to clear out the swarf... 🤦♂️😂😂
I'm so glad you wrote your comment. I first watched this video a couple of days ago and have been wracking my brain trying to remember the word "swarf" and it was driving me nuts, but I remembered a comment of this nature and dug in my history for a video about drilling so I could find this word without having to rewatch lol XD It's not even in the Wikipedia page that has a glossary of woodworking terms, I looked! Thank you lol!
Thank you so much!! I'm building out my shuttle bus in to a small home..and I've had one heck of a time because I didn't use my drill properly...now I can build my shelves and Frame my windows easily!
2 years after you filmed this, amazing info for me, I just bought my 1st drill and I'm putting up shelves. A few of your videos with fantastic tips and I'm confident I can do it with ease! 💁♀️☮💕🇨🇦
When drilling metals, every type of metal has a range of speeds for a given drill material. It absolutely does matter. I've made a nice living getting tools running at efficient speeds and feeds. It isn't always best to slow down, it is always best to let the tool do the work, and to have your head out of your ass when in the shop.
Excellent and thanks! I have a tip. Before starting on a job that has a lot of narrow diameter holes, buy a bunch of extra drill bit to have on hand so that you don't have to interrupt the project.
I've been a machinist and maintenance mechanic for fifty years of my 75 years in life. I can't tell you how many finger and hand infections I've had from clearing chips from drilled material using my hands or fingers. I learned what chip brushes and low air can do to remove chips without consequences. Just a thought. !
I agree with all of what you said, except for when drilling into steel. Generally yes drilling rpm are lower but not when drilling smaller holes. In that case the drill actually has to spin much faster otherwhise they will snap. The formula is the following : 12 x ( material cutting speed ÷ 3.14 x (drill diameter). Cutting speed for mild steel is 90ft/s
There may come a day when you need to perform a simple task like hanging some bookshelves for someone special. Now you will know how to do it, and you will be a real hero. Believe me I know. I have done simple projects for friends, and they love when I break out my tools and get to work.
How can I reem out a doorknob hole that just needs to be shaved on one side (inner)? What tool would I use? I tried using a drill bit but it didn't do much. Any suggestions? Thank you! Great video!
@@mercoid Thank you! Can I ask another question? What would you use to cut across the bottom of a wooden fence gate (with slats) - I need to make more room for pavers I'm setting down. I can't use my jig saw - no room. I'm only cutting off about an inch or two above the ground. I have one of those "multi tool" tools but it was a struggle. Would I need a Sawzall? I tried to use a hand saw too and it didn't work very well - too much work!. The gate has to be open while I'm doing this so there is no stability to push against. Thanks!
To reciprocate the drill bit out while drilling is called "to peck". In metalworking, especially when it comes to CNC, a pilot drill bit is used to start a hole. This type of drill bit doesn't wobble.
![[#2024MAMA] G-DRAGON - 무제(Untitled, 2014)+POWER+HOME SWEET HOME+뱅뱅뱅+FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/Ox29z5Nf1Uk/mqdefault.jpg)
Are you sure you’re using your power tools safely? Avoid the most common (and dangerous) mistakes! Get your FREE guide here 👉 bit.ly/10PowerToolMistakes
I've watched 5 videos today and I feel like I learned a years worth of information. Thank you.
Thanks for watching Corey! I’m really glad they’re helpful
You nailed it-there's so much helpful info in these short videos. I'm hooked.
I’m a carpenter. This man is the one to watch for real knowledge. I even enjoy the videos about things I’m already familiar with. A great ambassador for our profession.
And it has been a Year
Dude me too, this video blew my mind and made me realize how much I need to learn still.
I've been a woodworker for 50 years and in construction for 40. I probably didn't learn much from your video but I pretty much agree with everything you presented. Well done, excellent video.
Thank you, William! I appreciate that coming from someone of your experience level 🙂
Agreed. Speaking for myself I learned from experience and wish I had these passed to me years ago. So if you're a yungsta, pay attention. These tips will become second nature, but having them listed is very, very worthwhile.
Love your site. Helping people.. great tips
"I probably didn't learn much from your video"... the fact that you learned anything from this video means you are a bad woodworker. i'm not a wood worker and i learned nothing, every tip in this video is completely obvious to me and that makes you look bad im"h"o
@@pratwurschtgulasch6662 dont you understand english?
He did not learn anything, meaning he already knew what Ethan explained.
Additional metal drilling tips: Center punch where you want your hole to prevent wandering (same as you would for wood drilling). Add a drop of lubricating oil to the tip to cool and lubricate the cutting surface. After the hole is cut, use a larger bit spinning in reverse to slightly touch the hole to knock off sharp edges.
Solid advice! As a handy guy, I'm learning from all his vids and comments I read that just KNOWING what tradesmen do can take hours off a project by increasing precision or choosing a non-favorite tool.
Great video. How do I keep my drill level while drilling so that my drawer pulls won’t look crooked?
Number 1 sharp suitable drill bits, the angle of a wood bit at the tip is more acute.
2 suitable speed for material and bit type. Almost every woodworker I have ever seen, particularly on RUclips uses spade/ flat bits way too slow, they work best sharp and fast.
3 Use suitable machine !!
I liked the video. No one in my family ever used a drill themselves. Now i am thinking of getting one and trying to do things myself. Thanks a very informative video.
Great tips. I think I have done every one of these at some point. One I would definitely add is adding oil when drilling metal. It helps the cutting, keeps the drill sharper and helps cool the bit and material.
Thanks you so much.
That was years and years of lessons and experience in an 8 minute video.
I knew several, but TOENAILING!!! Oh my goodness, that is gold for me! Starting practice tomorrow. Thanks!
Super helpful!!! Single mom starting over in my late 30s. This was clear, concise, & i saw another comment from a vetran carpenter of 40/50 years validating your recommendations. Honestly, that means a lot to me as often the video will say one thing and then the comments in the bottom just say how wrong the recommendations are which is very confusing to me who has minimal experience. Thank you again so much! Definitely subscribing!
The lower speeds for metal vs higher ones for wood was indeed a good tip. I wasn't aware of it and had learnt it the hard way.
When I use tape for depth drilling, I make a little flag. Then when I get to the proper depth the flag swipes away the sawdust and you know you are done. This helps eliminate drill depth creep (by pushing on the tape) if you are drilling multiple holes.
Whoa.....
🤯
Exactly!
And ... I like to draw a small skull and cross-bones on the tape flag.
This doesn't improve the drilling process any. However, it allows me to pretend that I am the captain of a pirate ship, and thus, my workday goes by much faster. I literally sail through my workdays. 🤪
Ive done this for alongtime when using a hilti hammer drill for drilling concrete.
I use a piece of red duct tape bc the depth measure on them move in time. Crappy design. so if any inspectors are walking through they see i have it set for depth. They just walk by bc they know im the sht. Lol
@@UserUser14880,
Awe man ... So, you're the one that invented "red tape" ?
Gran idea!
Best DRILL video! It belongs on RUclips University as a core class for crafter's like me.
Yup, me too, thanks!
Hi Gloria 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
Holy cow. What an unreal amount of useful info! You even crammed extra tips into several of the tips lol. Great stuff, thanks man, so glad to have recently found this channel
adding to the vid, putting a piece of wood underneath the piece you're drilling into will also help prevent tear out.
Other than that, well paced and informative video. Thank you.
I found that out by accident. Spade bits are notorious for tear out. So far..I have not had any problems. I try always put a small piece of board underneath. So far ..so 👍
So far so good.. The 2 boards should be clamped togother if possible..time permitting ..and other factors...going slow or. A marker tape for depth are choices.
Oh yeah..years ago I bought a 50s hand brace..geared, and good quality wood handle. They built ships and houses out of them. I am old school. Sometimes I like to do something totally using hand tools.
The bigger the bit you're using, the more you need to use a sacrificial backer board.
Without exception, even with brad point drills, always have a board supporting the location where the drill will exit the wood.
Can you cover how to drill into concrete and installing concrete screws?
My concrete screws seem to pull out too easy because the hole i drilled is too large. I'm using the correct size and type of drill bit. I suspect my cheap hammer drill is not spinning the bit true, but is wobbling the bit which causes the hole to enlarge.
Get a good countersink bit so you prevent the tapered head of a flat head screw from splitting the wood, especially near the end of a board.
And in a pinch, use a bigger bit to carefully drill out a small countersink.
I liked this video. I've been a carpenter for 30 years and never heard of swarf. One tip that you left out that I like is when drilling with a spade bit or hole saw only drill until the point on the bit comes out then flip the wood over and drill the rest of the hole to prevent tear out. Keep making great videos!
You have no idea how valuable this video was for me. 👍
Thank you so much for your tips. As a single woman, I need to do what I need to do to get by. This bit (no pun intended) of information is extremely helpful.
You’re welcome Dionne! Thanks for watching...and for the pun 😄
Let’s be honest pun was intended
nice play on words ( pun intended ) lol
This is great! RUclips is like a handy dad. Now I can be a handy dad for my kids.
Yep. Except I’m not handing out tools and getting yelled at.
Im an electrical apprentice and find this very helpful great video
Great video. One major tip I would add is to make sure you're using the right drill bit for the material. Bits for masonry vs wood vs metal and even ceramics make a huge difference.
I didn't know there was a difference between wood bits and metal bits.
Thank you so much for making this video! I have had no training whatsoever, but have been building stuff for quite a few years, something I enjoy doing. However, I have had a lot of problems with drilling in the past. These tips were very helpful. A few of the things I had figured out to do on my own, but didn't know most of them. Can't wait to go drill using these new tips!
Thank you for the tips.hope you add some for concrete like tips for tox plugs,etc.
So many questions FINALLY answered! This was awesome! Thanks!!
Hi American girl 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
It's fun watching someone pass on info, for stuff that I have been doing over 30 yrs. It's always new to someone!
This was a perfect video for a beginner like me! Great tips!
It’s nice to use a general purpose oil when drilling metal
Cutting fluid is better, but any oil will work!
It's a good idea to use a coolant when drilling metal. This will extend the life of your bit before it gets dull. Even a light oil like wd40 is better than nothing.
Llllllllllllllllllllllllllllá0
I always thought higher speed was better for drilling metal, but now I know slower speed is better, thank you for this wonderful video.
Also should I use any type of oil for metal drilling
Great description of techniques, # 12 could be to apply a backer block (clamped or flat on the table) to avoid tear-out on the back surface of the work piece.
Great basic review. Glad to see I'm already using all those techniques. With regard to the painters tape, giving yourself a little extra wiggle room and not going to the depth of the tape is key when doing many holes; 1, 2, or a few probably won't be an issue, but the 144 I did for making a 6 hole adjustment for 6 shelves...the tape wears quickly. I also wind the tape counte to the spin so if the tape does touch the surface it doesn't unwind. I also use a long length of tape to give you more "bulk" at the stop point and fold the last half inch into a little flat so you're not only more likely to see when you're getting to close to the surface, i.e. drilling too deep, but it also makes it much easier to have the flap for unwinding it from the bit when you're done.
Thanks for the MANY valuable tips for drilling, etc for DIYers. Some knew about before, but others that I will apply. Looking forward to your next video.
using a drop or more of oil helps when drilling steel and dishwashing liquid when drilling metal. allows for faster drilling speeds.
You've answered all my questions in one go! Many thanks for sharing.... I'm off to put up a roller blind.
Wish me some beginners luck please.
Hi Susannah 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
I always watch ‘Basic’ videos. Amazing how much I’ve learned
by not thinking I know it all.
You offer quick and precise instruction. Cannot thank you enough!
Thank you for the tips really helps me with learning about tools.
Thank you for all your videos. I was trying to make simple plant stand and a bench. They are ridiculously expensive in store. I was inimidated by the amount of tool I needed for making stuff. When I came across your channel, I knew I can get away with 2 tools. Thank you for being honest.
Thank you for such clear and concise bunch of VERY useful tips! I’ve made a few blunders lately despite years of experience so it’s never too late to sharpen up the skills.
Very informative and right to the point. Loved it!
Excellent and short, right to the point. Thank you for saving my time.
To avoid tear out I have used tape as well but I prefer to clamp a piece of waste stock to the side where my drill bit will make its exit. I can always find a big enough piece of scrap wood to cover all the area where I am drilling holes to prevent tear out.
When I use hole saws or spade bits. Having scrap on one side is a big help but mostly I drill a smaller hole through my project first. Then use the spade bit or hole saw and just penetrate the wood on the one side part way in. Then drill through from the other side all the way using the small hole that is showing as my start point. That way you avoid making a messy tear out because the surface of the wood on both sides has been cut with no cutting tool that has broken through. I always keep in mind that some woods are more prone to splintering than others.
Two thumbs up! I always thought drilling slowly on the wood prevents chips, but learned something new today!
Tip #12....When building a project, use two electric drill motors. I do that all the time. It saves time from changing drill bits. I have already used three electric drills, one had a power cord since I don't collect drills.
Great video, all good tips.
Barry
Thank for this video. I’m a beginner and now I feel confident to start my first project 👍🏾
As a DIYer I really have enjoyed all of your videos amongst the many that I watch. Thank you for being dedicated to your trade and teaching it to others. Awesome stuff.👍🏽
Thank you, gr8ride!!
I learned the size up trick on my own when drilling into concrete. Helped tremendously
Yep, ESPECIALLY important in concrete
Do I need the hammer function turned on for the second (or third) size up on concrete wall? Because I live in an apartment, so I try to drill as least as possible and those hammer drills can get very LOUD, lol.
@@cynicalheis You have to use a hammer drill with a masonry bit when drilling concrete. Concrete is way too tough and hard for normal drills and just rotary drilling.
@@cynicalheis you may try a neumatic hammer drill, works better, no need force, not that loud.
After so many videos and articles this one was everything I needed. Very concise, thank you 👍🏽
Good tips!!
When drilling into concrete, Mark the depth you want on your bit with a black sharpie.
the drilling dust will make any mark on the bit unvisible. most of hammer drills have a depth controlling device. or make one by yourself
@berndeikers8924 they do, but from my experience, someone always loses it, lol. Whatever way works, I suppose, because there's a few ways to get it done
1) use your drill’s clutch to select the right speed for the job. there’s also usually a high and low gear (or 1 and 2). your low gear delivers more torque at the cost of rpms
2) hogging material can snap a bit quickly. your bit will often discolor at a stress point from heat before it breaks. also wear eye protection
3) obviously dont drill through a workpiece into anything that’ll damage the bit. or into anything that cant be damaged
Remember, when you’re clearing out swarf (I love that word) with your finger, be careful that the bit isn’t hot, or you could burn your finger (ask me how I know this).
You ain't the only one. If the bit is tiny, dad flicks the end of it. Usually the little bit of flex and rebound is enough to bounce out the swarf. My fingernails are always uneven lengths; I just use whichever one is long to clear out the swarf.
I love that word too. :)
HOW DO YOU KNOW THIS?
@@philipwright6065 ever touch a drill bit after drilling for a bit? Then you’ll know. Lol
@@ethanheyne It can't hurt to let the drill have a break to cool down, too.
Swarf would be a good name for a small dog.
Ha ha. Same.
Thank you so much! This is so helpful for someone who has 0 drilling experience like me
Great tips as always - I used coloured tape matching the rawlplug colour and depth on my masonry bits so they are ready to go, and easy to identify at a glance which plug goes with which drill.
Hi to mrJD - Liking the idea of coloured tape matching the rawlplug colour. That is one hell of a good tip. Ain't gonna forget that one. Thanks goes to The Honest Carpenter for creating this platform. Cheers and happy drilling !!!
Thanks for tips, Ethan. I wish I watched this before recently drilling into metal studs to install toggle bolts. It seemed to take forever.
On the bright side, I somehow figured out that I had to step up drill bit sizes for each hole. Seeing this approach confirmed in the video makes me feel a bit handy-dandy 👍🏽
Thank you so much for teaching me so many tips & tricks as well as showing me what tools and brands I need to buy. After 43 years of a happy marriage, my husband passed away last September leaving me to care for this property all by myself. At age 66, I'm now all alone and trying to learn what I need to know so I can make it on my own. Thanks for helping me learn the skills and products I need to repair my home.
Carol I am on a similar journey. We can do it! And I keep researching each task.
Hi Carol 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
Some I knew about. But as always learned more. Also when drilling metal you usually want to use drilling oil if applicable.
@JosLewisWood Carpenter I had a metal shop teacher in 8th grade teach me about slow drill speed for metal, but otherwise I'd never have known this.
About 50 years ago when I was in wood shop class my teacher told us students the best way to select a drill bit for a pilot hole. He instructed that we take the fastener we want to use and using a drill index to find the hole that the fastener will fit into. Then we were to back off two drill bit sizes and use that size bit to drill our pilot hole. It seems to have worked nicely for most holes, but occasionally when drilling metal, or very hard wood, only back off one drill bit size.
found a drill bit hole sizes template (13 hole sizes: 1/16"-1/4"), test the screw on a hole where it goes through and pick a drill bit 1 hole size smaller for hardwood, 2 hole sizes smaller for softwood
@@torTxoFognaTuluZ mastercraft hammer drill - included in the set of drill and screw driver bits (labeled as 'drill gauge'). it's 3x8 cm, made of plastic
My mother was a great self taught woodworker. She taught me most of these tips. Thanks for the reminder.
Very helpful to dyi’ers, especially those of us who weren’t allowed to take shop decades ago (because I was a girl). I’ve figured out most of this on my own as I love rehabbing homes for myself and my friends. Your video would have been great back when I had to figure out what I was doing wrong; now looking for instruction on what all the fancy drill bits are supposed to be used for as I have a number of them that came in a huge set but they don’t tell you what they do or in which applications they should be used. Thanks for the clear instructions!
Hi Stephanie 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
Great tips. Some I figured out on my own, like using tape for a depth gauge and others, like using an awl to make an indentation before drilling, I learned from my mom. Here are some of my tips. (1) Look at your drill bit when it's running. If it looks blurry, then the drill is bent, or it is not centered in the 3 jaws, or it is loose. (2) When you are tightening the jaws with a key, start in hole 1 and give a little twist to the key, then go to hole 2 and give a little twist, then go to hole 3 and give a little twist. Then repeat 1-2-3 until the jaws are tight. By moving from hole to hole in a circle to tighten the jaws, you keep the drill centered in the jaws. (3) When inserting a small drill, like a 1/16 or 5/64, start with the jaws closed. Then gradually open the jaws until you have just enough of an opening to insert the drill and tighten. That will insure that the small drill is centered between the jaws. Always wear eye protection when using a drill.
If you're drilling with a fine bit and it snaps and you don't have a spare, grab a nail of the diameter, snip off the head and use the nail as a drill bit. It's not perfect but can get you out of a tight spot.
Another great tip Maxx. I’ve got a certain way of cutting then to get kind of a chisel point out at the end. Have definitely used that trick more than once
Been there done that..the fine brass looking ones that come in a blister pack (read cheap), break super easy. It just occurred to me.
If you are not making progress
with the bit..put it in vice or clamp. the nail to a table..then file cross hatches or just basically rough the tip area of nail up. Never tried it ..btw..I am in the process of putting brushes etc in my 30 year old Ryobi hammer drill. It has been put though the.ringer..
I agree with you on the "punch" thing! It can be really annoying when the bit wanders around on the surface on it own. Sometimes you don't have something to punch the surface with though. What I do is I place the bit where I want it, then I place my offhand on the back of the motor casing, above the drill grip. I then apply pressure, and give a short, quick pull on the trigger. Makes sure to do it fast, so the bit stays in place. Another method I found is taking the right size bit, or a bit smaller than it, and grab it in your hand, and twist it side to side, making a little indent in the surface your drilling. This effectively does the same thing as a punch, but it may not go as deep.
Great Video! Recently found your channel so a new sub here. One tip that I like for finding the right size drill bit to use to pre-drill for a screw is to use the drill index. Find a drill bit that the screw will just fit into easily then go down two to steps smaller from that drill bit size. You can vary the number steps for softer or harder woods.
A tip for masonry, that I learnt recently
Make sure that the masonry drill bit is all the way to the back of the hammer drill/ drill hammer setting.
Thanks for sharing these useful tips, some I knew some I find not
Great video, lots of good info. One thing I discovered:
I bought 10 packs of cobalt bits on line, of the most popular sizes that I often wear out or break; 1/8 and 1/4. Not too expensive, and cobalt bits are excellent!
You're so right about 1/8" bits. I always have extras.
Very well explained. I just bought my first drill and these tips are really spot on for a beginner like me. So thanks a lot.
Dang, if I keep watching his videos he's gonna make me into an actual carpenter.
I think for diy and beginners a pocket hole jig for angles and a stop collar for depth would be a good investment.
Good tips though.
Even old dogs need to see if there are any new tricks out there.
Keep up the great work with concise to the point videos. 😎
With the tape on the bit method, another good trick is to leave a flap of excess tape folded onto itself. This serves to sweep away saw dust from the surface being drilled once you’ve reached to prescribed depth without you having to peer down at the work so closely.
Great video! The only thing you missed was preventing splintering (aka, 'blowout') on the reverse side of the piece
I've commented before; but that Hitachi drill is the shiz! I've had one for years now. It's been my favorite by far.
Really cool tip see someone else with one! 👍🏼👍🏼
hitachi bought metabo, so actualy is a metabo drill. good stuff
I was able to screw half a screw to prop up a fallen picket, and gave up. After watching your videos on fasteners (love learning new words) I purchased exactly what is required for this very tiny job, and hope to complete it on my day off. Thank you for the lessons 🖖
Hi Sandy 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
I needed to drill two shelf bracket holes into an expensive curio cabinet. Super helpful suggestions!
Just got my first brad point drilll bit set, and it makes precise holes in soft woods go much faster. Let's you drill a nice clean hole exactly where you want with a single step. No need to punch or tape., but it is another set of bits to keep track of, of course.
Also, get some bees wax or a bar of soap to apply to your threads before inserting the screw, especially in hardwoods. This will make the screws go in so much easier. P.S. If you are doing a lot of toenail screwing then get a Kreg jig (I know, this is not a simple screw technique but wanted to throw this in).
Also any any kind of candle wax will work. Which most house holds have.
@@angellas.1314 Cool. Was just going to ask whether candle wax would also work. :-)
I've been trying to drill the mushroom rivets open on my hotwheels madpropz, but i couldn't figure out why it wasnt working, until you said that i should drill slowly. The mushroom rivets on every hotwheels is made of metal, and your tip worked wonders, i managed to drill a hole
Just bought my first drill, and thanks to you, I know how to use it
Hi Brenda 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
Great tips. Drilling on angle!
I like to wrap my tape around but also making a blade with the tape so when drilling the blade will clear away the debri!
I am loving your channel. I just bought a house and I'm trying to save money by learning to do things myself. You have helped me a lot. Which of course saved me a lot of money. Thank you!
@tamasaii You’re welcome! Thanks so much for watching. I’m glad it’s helping 🙂
Some stores will markdowns wood up to 70%..I recently found.out that slightly defective
boards etc can qualify. Just ask
..it doesnt hurt anything. Stores
actually benefit from this..it saves
them from.having shoddy stock and taking the time to cull lumber.or.any other.product. I use old pallets to hold things..of course safety is always your.first
concern.
I bought my first drill today and although have drilled a few holes with it I am glad I found this today. Thank you for quick helpful tips.
Hi Lesley 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
#1 tip... always expect the bit to be hot!
Same with screws
Thanks man. Learned a lot and confirmed a few lessons that I’ve learned myself the hard way. For plasterboard fasteners I keep an old bit of plasterboard in my garage so you can practice and see what’s happening before drilling the walls in my home. 👍
All the new terms I discovered: swarfing, hogging out, toenailing... and also how come I keep breaking drill bits. Thank you for this! I learned a lot.
You're welcome, Bonnie! Thanks for watching :)
There are a few reasons why drill bits break when I'm using them.
1. I'm pushing to hard
2. Drill bit caught on a harder material while drilling into a hole. Example: Drilling into wood and you hit metal. The drill bit catches on the metal and breaks.
3. Cheap drill bits. Always buy good drill bits. For most DIYers and Contractors HSS drill bits will work just fine. HSS stand for "High Speed Steel." These are drill bit that have been heat treated to increase the hardness of the drill bit.
4. Drill bits typically go on sale: Christmas, Father's day, Memorial Day, 4th of July, Labor day. However, I find quality drill bits at their lowest price during the Christmas shopping season in the "stocking stuffers isle" or on Father's day. The big box stores put them out as their loss leader and you can typically get them for about 40-50% off.
5. Last but not least. Always wear safety glasses.
Bits break often for three main reasons:
-pushing too hard (small bits flex)
-change of direction 1/2 way through hole
-cheaply made bits (bad temper on bits)
Hi Bonnie 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
I thank you for your sharing knowledge. It’s better to give than to receive. God bless you and your family and business for doing this.
Thanks! I now have to salvage my project. Drilling fast takes confidence so I think it's wise to test on a piece of scrap wood. I also have a problem to drill straight for my dowels.
To help drill straight vertically. Fix together two pieces of wood to form a L shape about half the height of the bit your using. Then place the bit where you want to drill,and then place the L shape piece up against the bit where the corners meet. Then drill; it will not be 100%,but much better then trying to drill free handed. Also to drill a straight hole horizontally; you could do the same thing,but it can be cumbersome. I saw a trick on "Wood by Wright" where you place a cheap ring,key ring,or perhaps even a washer onto the drill bit itself so it can spin freely; then place the bit where you want to drill,and place the ring about middle way of the bit then drill your hole. An if you tilt the drill up to much the ring will slide towards your work,and if you tilt the drill down to low the ring will slide toward your drill. I realize the last tip sounds like a lot,but once you try it you be like oh okay piece of cake. LoL Hope this helps.
www.amazon.co.uk/Wolfcraft-4640000-Dowel-Master-dowel/dp/B0001P19PY
@@davogifman542 Can you show a photo of how this is set up. Also, looking for something like the wolfcraft fowl jig listed below in the US. Thanks so much.
@@liamofthornhill Can you tell me what a cheap comparable jig would be Amazon US? I'm putting together a bed frame with 2" x 2" poplar hardwood with a butt joint, and I think it will be hard to make straight holes. Thanks.
@@barbarakaimowitz9138 www.ebay.com/itm/Handheld-Woodworking-Doweling-Jig-Drill-Guide-Wood-Dowel-Drilling-Hole-Saw-Kit-/224246369046 I'm in the uk but eBay is a good try
Absolutely fantastic - I learnt a lot.
Many thanks......all the way from London !
Thank you so much I was looking everywhere for "why won't my drill bit cut through hardware" when all along I just needed to clear out the swarf... 🤦♂️😂😂
I'm so glad you wrote your comment. I first watched this video a couple of days ago and have been wracking my brain trying to remember the word "swarf" and it was driving me nuts, but I remembered a comment of this nature and dug in my history for a video about drilling so I could find this word without having to rewatch lol XD It's not even in the Wikipedia page that has a glossary of woodworking terms, I looked! Thank you lol!
@@ItsAsparageese lmao you're very welcome! =D
Thank you so much!! I'm building out my shuttle bus in to a small home..and I've had one heck of a time because I didn't use my drill properly...now I can build my shelves and Frame my windows easily!
Glad to hear, Jess! Good luck! 🙂
Great video as always. Keep up the good work!
Thanks buddy!
2 years after you filmed this, amazing info for me, I just bought my 1st drill and I'm putting up shelves. A few of your videos with fantastic tips and I'm confident I can do it with ease! 💁♀️☮💕🇨🇦
When drilling metals, every type of metal has a range of speeds for a given drill material. It absolutely does matter. I've made a nice living getting tools running at efficient speeds and feeds. It isn't always best to slow down, it is always best to let the tool do the work, and to have your head out of your ass when in the shop.
Applying cutting oil, ( me , pb blaster , got cans of it every where) on metal, usually helps.
Excellent and thanks! I have a tip. Before starting on a job that has a lot of narrow diameter holes, buy a bunch of extra drill bit to have on hand so that you don't have to interrupt the project.
I've been a machinist and maintenance mechanic for fifty years of my 75 years in life. I can't tell you how many finger and hand infections I've had from clearing chips from drilled material using my hands or fingers. I learned what chip brushes and low air can do to remove chips without consequences. Just a thought. !
That’s a good point Frank. Thanks for writing in with the advice!
I agree with all of what you said, except for when drilling into steel. Generally yes drilling rpm are lower but not when drilling smaller holes. In that case the drill actually has to spin much faster otherwhise they will snap. The formula is the following : 12 x ( material cutting speed ÷ 3.14 x (drill diameter). Cutting speed for mild steel is 90ft/s
I have never held a drill in my life, and I'm not looking to drill anything anytime soon. But damn that was entertaining to watch.
There may come a day when you need to perform a simple task like hanging some bookshelves for someone special. Now you will know how to do it, and you will be a real hero. Believe me I know. I have done simple projects for friends, and they love when I break out my tools and get to work.
How can I reem out a doorknob hole that just needs to be shaved on one side (inner)? What tool would I use? I tried using a drill bit but it didn't do much. Any suggestions? Thank you! Great video!
Use a rasp with a rounded surface. Employ a version of Honest Carpenter’s tape tear out prevention method to avoid cosmetic damage to the door.
@@mercoid Thank you! Can I ask another question? What would you use to cut across the bottom of a wooden fence gate (with slats) - I need to make more room for pavers I'm setting down. I can't use my jig saw - no room. I'm only cutting off about an inch or two above the ground. I have one of those "multi tool" tools but it was a struggle. Would I need a Sawzall? I tried to use a hand saw too and it didn't work very well - too much work!. The gate has to be open while I'm doing this so there is no stability to push against. Thanks!
Great tips Ethan....”swarf”....who knew lol
Thanks Ed! Always liked that word 😁
To reciprocate the drill bit out while drilling is called "to peck". In metalworking, especially when it comes to CNC, a pilot drill bit is used to start a hole. This type of drill bit doesn't wobble.