Check Out the ULTIMATE CARPENTRY CHECKLIST!! *Get your free interactive ebook here* : www.thehonestcarpenter.com/the-ultimate-carpentry-checklist This *150-item Visual Glossary* covers every important topic in carpentry. Check off the tools you have, the concepts you understand. And if you don't know a topic, just click on it for an explanation. Every carpenter and DIYer needs this free guide!
I admire you for teaching to the true beginners. We were all rookies once and knew nothing. Instead of laughing at them for not knowing, just teach them. Don't be an ass, be a friend.
A piece of cardboard can work too. Poke the nail through a piece of cardboard, and hold _that_ to hold the nail while keeping your fingers out of hammer's way. You can tear the cardboard away from the nail once it's got firmly started and doesn't need to be held any more.
A tip for really tiny panel pins etc is to push the pin or nail through a small strip of card ( eg :cereal box ) and use it to hold the pin or nail while you start it with the hammer. Saves your fingers if you miss.
I had an employee review yesterday and one of the things they brought up was that they liked how I spent time outside of work learning more about the tools I use and they could see that it has made me better at my job. I'm a house painter but we use most of the same tools in carpentry (not least becsuee the GC's out where I am are awful and hire crappy temp crews to pump garbage trim sets and shoddy drywall out.) I have learned quite a bit from your videos and I apply that knowledge on my sites. Thank you!
That's great to hear about the review, Taylor! You're going to improve way faster than everyone else by delving into the carpentry side of things--all the great painters I know have an extremely wide base of construction knowledge. I'm really glad the videos have helped--good luck in 2021, and be safe!
@@TheHonestCarpenter Great initiative. Also, it is a good idea to never bash the trades. We get bashed enough from other sources. There is always a way to explain others poor performance in a more diplomatic way. I appreciate your concern for a job well done to the extent that my painting sub-contractor was also a big part of my quality control.
@@edover50 it's called a combination square. Because it does 90° and 45° A lot of times the scribe is missing on them too. Because lots know about it and tend to lose the things. For the most part I like to use a full sized scribe myself. I have a couple nice scribes. In a pinch every nail and screw is a scribe.
Nice video. Quick paced and informative. I was an interim administrator at our local vo-tech school following my retirement and watched the instructor give most of these tips to his students. He didn’t show them the multi tip screw driver as a nut driver. I asked him if he ever mentioned that to his students. He kind of laughed and told me that he was sure they all knew that trick. But, he told me to come back to his class the following day as he would be asking some of his students individually if they knew the trick. It turns out that many did not know. He was surprised and added that tip to his instructional repertoire.
Thank you for making these videos. As a new homeowner this is especially helpful. I asked my inspector if there was a place I could go in person to take classes on home maintenence or repair to do on my own. Instead he told me there was a list he provided of people to call to do the job for me. Thanks again for your videos. I'll continue to watch and learn.
Heck yeah! I knew all of these and use them while doing my projects! Thanks goes out to my Dad and step-father for showing me these things growing up. Now if I could my kids to help me so they could learn...
theses vids have helped me a tonne. ive been bartender for 10 years but due to lockdowns i had to find work helping a general contractor i know. so this basic stuff has helped me get by so far. its a start. thank you
I like that you have all 21 tips listed in the YT description paragraphs. It is a big reason why I subscribed to your channel today. I see you have currently 143 videos. Keep up the good work MR. E.J.
These are great tips for beginners and pros alike. Easy to watch the whole vid even through some of the beginner tips. Super job. It’s no wonder you have 198k subs now!!!
Yeah I've literally learnt so much from this one channel and at the best time possible (because I was getting into light carpentry/woodworking). Now I almost feel like I could get into the heavier stuff too. Maybe even make a bit of money from it.
its good you are using old tools and not throwing them away. people keep throwing things out that can be perfectly be used. its good you are using them well.
Thank you this was partly a walk down memory lane as I used to watch my father pipe fitting superintendent of some renown when he worked around the house and he would show me little tricks. I sent this to my daughter because I know she did not have that privilege from her father
I learned quite a bit. Very helpful and your style of teaching is very pleasant. This is second video of yours I've seen. I will be watching more. Much appreciated!
I often use this to bend the nail over and then just claw pull as normal, saves the time of sticking a block underneath it for more leverage. Usually no need to "see-saw" it out as he did.
Be careful zig zagging nails with a wooden handled hammer. They don't all like to do it. Don't ask me how I know. Or why I have so many metal handled hammers now. Your other option is to get a good crowbar.
Thank you. If I'm watching you videos don't assume I know a lot of these. I took half a semester of wood shop in Jr High before shop classes were cut so I appreciate all there insights.
You're welcome, Jose! I'll be sad when the day comes that shop classes aren't taught anywhere. I'm hoping we can help bridge the gap a little bit here on RUclips. Thanks for watching! 🙂
Sorry to hear Jose. I was fortunate to take a shop class growing up. I learned basic welding back in the day. My father always said, you can go to college and get a degree but having a trade you can always fall back on when times get tuff plus save $$$ DIY. I'd like to learn more about electrical.
The scribe is great, but if you can't quite see it so well after scratching it in, may I suggest a sharp mechanical pencil? .7mm or even better a .5mm makes the line obvious in any lighter wood, and is easy to mark in a scribe or scratch!
You are what you say you are very honest and it's totally appreciated. It really is. Your honesty and showing everybody stuff I'm sure you're making tons of money but you deserve tons of money. Your honesty is the best policy the best policy thank you so much like I said I'm a female living in a home alone here and without you I would have to keep searching on RUclips for other people LOL
I am always so happy to see your videos. You make me want to go out and fix something. In my run-down house, there is no lack of opportunity. Thank you and Happy New Year!
I think your videos are brilliant and very helpful tips. I’ve grown up without a dad so my mum and I had to do diy. Now I’m an adult who now again lives on my own and I do diy and I have learnt some really good tips and tricks I will take on board and look out for more from you as you explain so well thank you.
Those 21 tips in 9 minutes was a great watch Fast paced but not speeding though things Perfectly fit for my waning attention span These are all great helpful tips! Keep up the good work Happy new year
Excellent! i knew (and have used) most of these tricks over the years, but I did not know about the combination square scribe tool, or using the speed square for angled saw cuts. Even experienced woodworkers can learn something new. Thanks!
Honest Carpenter your channel connects creative minds with mindful creation, practicality, bridging for so many an insurmountable gap that keeps their dreams just dreams. The path to mastery is paved, a master accomplished, with how well those that find in them what to learn, do. Every video of yours takes me higher, makes me better, growing my confidence in achieving my dreams. Tips, tricks, advise, how-to and how-not-to, a top category channel for sure! Thank you.
THANK YOU for saying something about needle nose pliers for nails! I see so many tricks for hold nails and your video is the first one where I saw the trick that I've been using for years!
Me as well. My grandfather was a great carpenter, but unfortunately I did not have the opportunity to hang with him. These videos are a wealth of info for diy'ers.
Watched this video a lot and will in the future. It reminds us that think we r pros to not become complacent. Thats when we get hurt. This video providee just enough info to remind pros and inform DIY ppl. Very good video sir. I have it saved forever
Thank you for all the much needed tips and tricks! I have each and every one of those tools... plus. As a DIYer those tips will really come in handy! Keep them coming! ☺️
Hope you did more RUclips videos recently than shorts like wood wood, those are amazing but with this longer versions I learn a lot more. Thanks always for all the tips and lessons
It never cease to not amaze me you have so many people that are ready to put a thumbs down on good information. Thank you sir for taking the time out for this. Some of these has never crossed my mind. I use my tape measure all the time and never ever thought to use that tab to mark 🤣🤣 🤦🏾♂️
Very good information and video. I have to admit that I've taken hand tools for granted. I'm a hvac and refrigeration guy my whole adult life and a home carpenter at my house. My hobby is wood working, but with hand tools and my goal is to learn as much as I can so I could do this when I retire God willing. Anyway I purchased a book called Hand Tools Their Ways and Workings by Andrew A. Watson. A very good book for information and easy reading. Thought I had it all figured out. Happy new year. Aldren A Watson.
this is the best youtube channel for learning about this stuff...your communication style is so quick and clear and you keep all this info interesting. it's just a flawless way to learn about tools and techniques
I got two great things from this video. First, I learned some new techniques with tools I've already got. That's valuable. Second, it turns out I'm a somewhat experienced home DIYer?! Who knew? So way to go, teach me something new and make me feel smart at the same time. Well played.
You are a great teacher! If I were influential in a school district or state-wide educational program, I’d utilize you and your skills to begin a program in schools teaching REAL, valuable skills that would, over time, show up in our culture. People would be spending more money on tools and home/neighborhood improvement and less on tattoos and body piercings.😄
What a great video. I'm a maintenance mechanic in a college. Most of my career in shops, most guys I worked with didnt even know this much.this is like a class every maintenance guy should take
Great video. The only mini hacksaws I have are just miniature versions of the larger frame type, which also dont fit into certain areas. That lockable handle for a full size blade would be incredibly handy. 👍
I appreciate these videos types of videos. They are especially useful for passing on information to the next generation. I don’t always remember all the tricks on demand, but they are there when I need them.
No wonder I never got precise measurements with my tape rule, I've always flattened the rivets down tight with a hammer and punch ,tape against tab, figuring it was just a cheap tape measure! Honest Carpenter= IT'S SUPPOSED TO MOVE!!!! you just got a new subscriber!
This is so brilliant I loved these experienced tips and tricks of the trade, I learn so much from your how to use these tools videos, its essential to know how to use the tools correctly and safely I really appreciate these types of informative demonstrations it's so valuable knowledge, I'm a very inexperienced DIY-er I can use a drill put up shelving but I lack knowledge of what tools to use and how to use them, I really dont know how to operate handsaw tools, as I've never used them before, but I would love to learn and feel more competent and confident, your channel is excellent I'm loving it all, please keep it coming, do you have any videos about how to use jigsaws, bandsaws and what's the best way to cut circular projects in wood what's the best tool for that? Thank you new subscriber Laura in England
Great stuff! My favorite is usage of long-nose pliers to hold small nails. +1 comment made re: slip-joint back jaws to cut stuff. Two additions not already mentioned in comments by others: * Instead of screwdriver to turn eye bolt, you can also use Crescent adjustable wrench for a different handle angle and for more contact with eye bolt * The back side of long-nose pliers have high leverage flats that can be used to crimp stuff (in a pinch ;-)
You can also use shaft on 6 in 1 screwdriver to extend hex shank drill bits. This is something that has saved me many times when your drill bit is just not long enough.
Check Out the ULTIMATE CARPENTRY CHECKLIST!! *Get your free interactive ebook here* :
www.thehonestcarpenter.com/the-ultimate-carpentry-checklist
This *150-item Visual Glossary* covers every important topic in carpentry. Check off the tools you have, the concepts you understand. And if you don't know a topic, just click on it for an explanation. Every carpenter and DIYer needs this free guide!
I've used most of the tools you showed for over 50 years and never heard some of these tips before - thank you for great info.
I admire you for teaching to the true beginners. We were all rookies once and knew nothing. Instead of laughing at them for not knowing, just teach them. Don't be an ass, be a friend.
Agreed. Now go get the wood stretcher.
Nice job on the video. I never knew there was a scribe in the speed square.
@@justindavenport9182 have you seen the lightbulb bender or cable stretcher.?
@@micho2062 lightbulb bender is a good one, havnt heard that
No
Needle nose pliers for hammering, so simple yet something I have never thought of doing. Bravo sir!
A piece of cardboard can work too.
Poke the nail through a piece of cardboard, and hold _that_ to hold the nail while keeping your fingers out of hammer's way.
You can tear the cardboard away from the nail once it's got firmly started and doesn't need to be held any more.
I have done that for many years. Did learn other things here also.
A tip for really tiny panel pins etc is to push the pin or nail through a small strip of card ( eg :cereal box ) and use it to hold the pin or nail while you start it with the hammer. Saves your fingers if you miss.
Knew all of these, yet never could hear them again enough! Without a doubt, these have saved so much time and solved so many problems on the job site.
I had an employee review yesterday and one of the things they brought up was that they liked how I spent time outside of work learning more about the tools I use and they could see that it has made me better at my job. I'm a house painter but we use most of the same tools in carpentry (not least becsuee the GC's out where I am are awful and hire crappy temp crews to pump garbage trim sets and shoddy drywall out.) I have learned quite a bit from your videos and I apply that knowledge on my sites. Thank you!
That's great to hear about the review, Taylor! You're going to improve way faster than everyone else by delving into the carpentry side of things--all the great painters I know have an extremely wide base of construction knowledge. I'm really glad the videos have helped--good luck in 2021, and be safe!
@@TheHonestCarpenter Great initiative. Also, it is a good idea to never bash the trades. We get bashed enough from other sources. There is always a way to explain others poor performance in a more diplomatic way. I appreciate your concern for a job well done to the extent that my painting sub-contractor was also a big part of my quality control.
Now tell them to compensate you for that time.
I’ve watched 7 of your videos so far, all excellent, I’m a beginner, you’re a good teacher. Thank you. ☮ from California
I'm a former pro carpenter, yet you taught me a new trick! Scribing with a tape measure was new to me. Many thanks, Ethan 👍🏼
Wow! Where u been!!! Jk!
True indeed ;)
Pro and did not know that ... former lol
Once a pro always a pro
Only works on a soft surface. Plenty of ppl use a tape for alot of different surface measurements that this wouldn't work on unfortunately.
3:01 no.6 Blew my mind! That is the silliest and intelligent DIY tip I ever heard.
GREAT VIDEO!.. the scribe in the sliding square... that was a new one for me! Thank You
Thanks, Jim! I love a good, hidden feature :)
I’ve been using a sliding square forever and was like “what””!! Can’t believe I never knew there is a scribe there !
@@edover50 it's called a combination square. Because it does 90° and 45° A lot of times the scribe is missing on them too. Because lots know about it and tend to lose the things. For the most part I like to use a full sized scribe myself. I have a couple nice scribes. In a pinch every nail and screw is a scribe.
Made me thankful I had a Dad growing up. Happy Fathers Day! To the next project on the honey do list!
Nice video. Quick paced and informative. I was an interim administrator at our local vo-tech school following my retirement and watched the instructor give most of these tips to his students. He didn’t show them the multi tip screw driver as a nut driver. I asked him if he ever mentioned that to his students. He kind of laughed and told me that he was sure they all knew that trick. But, he told me to come back to his class the following day as he would be asking some of his students individually if they knew the trick. It turns out that many did not know. He was surprised and added that tip to his instructional repertoire.
Thanks for the grat tips!
Thank you for making these videos. As a new homeowner this is especially helpful. I asked my inspector if there was a place I could go in person to take classes on home maintenence or repair to do on my own. Instead he told me there was a list he provided of people to call to do the job for me. Thanks again for your videos. I'll continue to watch and learn.
You have the only channel where every tip is simple, practical, and actually works. No fluff
While I didn't learn anything new, this video was a great refresher.
Heck yeah! I knew all of these and use them while doing my projects! Thanks goes out to my Dad and step-father for showing me these things growing up. Now if I could my kids to help me so they could learn...
Slip joint pliers have a great fencing wire cutter built into them, they will even cut softer fencing staples/nails.
Wrap a rubber band around your slip nose pliers handle . It's not vice grips but it really helps a lot.
Love these tips for non-carpenter folks! Thanks!
No wasted fluff in this video. Nice
Thank you, Ric!
theses vids have helped me a tonne. ive been bartender for 10 years but due to lockdowns i had to find work helping a general contractor i know. so this basic stuff has helped me get by so far. its a start. thank you
That’s great to hear, Mike! Good luck working in the construction industry, stay safe 👍
The nail set trick to make a pilot hole was new to me. Thanks for the good information!!
I use a spring loaded center punch for the same task. Its even easier as you don't need a hammer!
Great tips. I've been a DIYer for45 years and learned some new things today with your video. Thanks.
I just smiled through the video. Great info for many.
I like that you have all 21 tips listed in the YT description paragraphs. It is a big reason why I subscribed to your channel today. I see you have currently 143 videos. Keep up the good work MR. E.J.
Love tip #6! I would have saved my thumb numerous times had I known that tip!
Learned out of painful necessity, Robert 😁
Lol.smash fingers ...
This is the second time I have watched this video and it was a great reminder of the uses all these tools provide.
Thank you, thank you, thank you! I will watch again a lot!
You're welcome, Melanie! Thanks for watching, and work safe 🙂
Every man could benefit from this video, thank you so much!
These are great tips for beginners and pros alike. Easy to watch the whole vid even through some of the beginner tips. Super job. It’s no wonder you have 198k subs now!!!
Thanks, buddy! You're closing in on 10k! That's right about the time things start to really speed up--keep going! 😄
I agree. A lot of videos tend to go on and on about very simple stuff. He says what needs saying and moves on. Good job
Yeah I've literally learnt so much from this one channel and at the best time possible (because I was getting into light carpentry/woodworking). Now I almost feel like I could get into the heavier stuff too. Maybe even make a bit of money from it.
its good you are using old tools and not throwing them away. people keep throwing things out that can be perfectly be used. its good you are using them well.
The video was good, but the shopping list in the description is fantastic! Thanks for putting this together.
I'm 50+ and no stranger to a tool, and I still learned a lot from this video. THANKS!!!
Thank you this was partly a walk down memory lane as I used to watch my father pipe fitting superintendent of some renown when he worked around the house and he would show me little tricks. I sent this to my daughter because I know she did not have that privilege from her father
I had to stop this video halfway to say, your videos are freaking awesome. They are my new addiction. Thanks so much for sharing all these great tips.
Thank you, Derek! 😄
Thanks for all the helpful tips - no BS straight to the point! 👍
I learned quite a bit. Very helpful and your style of teaching is very pleasant. This is second video of yours I've seen. I will be watching more. Much appreciated!
your suggestion to side pull the difficult nails is something I didn't know. thanks
I often use this to bend the nail over and then just claw pull as normal, saves the time of sticking a block underneath it for more leverage. Usually no need to "see-saw" it out as he did.
Be careful zig zagging nails with a wooden handled hammer. They don't all like to do it. Don't ask me how I know. Or why I have so many metal handled hammers now. Your other option is to get a good crowbar.
Thank you. If I'm watching you videos don't assume I know a lot of these. I took half a semester of wood shop in Jr High before shop classes were cut so I appreciate all there insights.
You're welcome, Jose! I'll be sad when the day comes that shop classes aren't taught anywhere. I'm hoping we can help bridge the gap a little bit here on RUclips. Thanks for watching! 🙂
Sorry to hear Jose. I was fortunate to take a shop class growing up. I learned basic welding back in the day. My father always said, you can go to college and get a degree but having a trade you can always fall back on when times get tuff plus save $$$ DIY. I'd like to learn more about electrical.
@@ralpht7665 great advice. It is always a good idea to diversify your skill set.
Great tips! I am going to switch from pencil to utility knife to mark my crosscuts. 👍🎺
Opens a whole new realm for clean cuts, Kevan. X-acto knives are even better for detail work!
They also make a tool called "marking knife"... not sure if it's any better or worse than exactly knives... seems like it would be the same.
The scribe is great, but if you can't quite see it so well after scratching it in, may I suggest a sharp mechanical pencil? .7mm or even better a .5mm makes the line obvious in any lighter wood, and is easy to mark in a scribe or scratch!
You are what you say you are very honest and it's totally appreciated. It really is. Your honesty and showing everybody stuff I'm sure you're making tons of money but you deserve tons of money. Your honesty is the best policy the best policy thank you so much like I said I'm a female living in a home alone here and without you I would have to keep searching on RUclips for other people LOL
I am always so happy to see your videos. You make me want to go out and fix something. In my run-down house, there is no lack of opportunity. Thank you and Happy New Year!
I think your videos are brilliant and very helpful tips. I’ve grown up without a dad so my mum and I had to do diy. Now I’m an adult who now again lives on my own and I do diy and I have learnt some really good tips and tricks I will take on board and look out for more from you as you explain so well thank you.
Hey Ethan, how about a video about different saw blades and their uses? Great channel, thanks!
Those 21 tips in 9 minutes was a great watch
Fast paced but not speeding though things
Perfectly fit for my waning attention span
These are all great helpful tips!
Keep up the good work
Happy new year
Thank you. I am going to take a closer look at some of my tools right now.
So many brilliant engineering feats lying right there in our tool boxes, George. I'm constantly finding more!
Using the speed square as a circular saw guide is an excellent tip! Thank you
Excellent! i knew (and have used) most of these tricks over the years, but I did not know about the combination square scribe tool, or using the speed square for angled saw cuts. Even experienced woodworkers can learn something new. Thanks!
Honest Carpenter your channel connects creative minds with mindful creation, practicality, bridging for so many an insurmountable gap that keeps their dreams just dreams. The path to mastery is paved, a master accomplished, with how well those that find in them what to learn, do. Every video of yours takes me higher, makes me better, growing my confidence in achieving my dreams. Tips, tricks, advise, how-to and how-not-to, a top category channel for sure! Thank you.
I’m a newcomer and these tips were definitely handy. 5 of them I didn’t even realise could be used that way. Thanks 😅
Been doing this for years. It's nice to know it's OK to share the knowledge. Keep going, its awsome.
I had heard some of these, figured some out on my own, and learned others by watching this. Great stuff, earning a "like" and a "subscribe"!
I love your videos and you always give the best no nonsense tips and tricks. The toenail trick was great.
This video should be played in every shop class. I sit and wonder why I don't know some of this stuff.
THANK YOU for saying something about needle nose pliers for nails! I see so many tricks for hold nails and your video is the first one where I saw the trick that I've been using for years!
I’ve been amazing people with what I don’t know for many years.
LOL
Hahaha
Me too!
Didn't know people don't know things. 😊
Me as well. My grandfather was a great carpenter, but unfortunately I did not have the opportunity to hang with him. These videos are a wealth of info for diy'ers.
I’m a beginner DIYer. I’m learning so much from your channel. You explain everything very well.
Using the tab on the tape measure to scribe marks is gonna be a game changer on the jobsite!
Watched this video a lot and will in the future. It reminds us that think we r pros to not become complacent. Thats when we get hurt. This video providee just enough info to remind pros and inform DIY ppl. Very good video sir. I have it saved forever
Thank you for all the much needed tips and tricks! I have each and every one of those tools... plus. As a DIYer those tips will really come in handy! Keep them coming! ☺️
the tips were spot on and the tools were well used even better
Great collection of tips!
You should include one for the Ladder Mover, it has lots of uses beyond moving ladders.
Hope you did more RUclips videos recently than shorts like wood wood, those are amazing but with this longer versions I learn a lot more. Thanks always for all the tips and lessons
Needlenose pliers to hold a nail. GENIOUS!!
OR A POCKET COMB
@@keithcronk7980 Good one!
@@ethanheyne 👍👍👍👍🇺🇸🇺🇸
Good tips and it never hurts to review what's handy and possible.
Thanks - didn't know about the tape measure end tab being 'loose' intentionally. Just thought it was worn !
I knew it was loose intentionally because it's like that on every tape measure I've ever seen, but I didn't know *why* it was loose until now.
It never cease to not amaze me you have so many people that are ready to put a thumbs down on good information. Thank you sir for taking the time out for this. Some of these has never crossed my mind. I use my tape measure all the time and never ever thought to use that tab to mark 🤣🤣 🤦🏾♂️
I knew them all already but it was entertaining. And made me feel like I know more than I really do.
The hidden scry in the level square is the one thing here I didn't already know. Thanks friend, I learned something today.
Fantastic. Posting link to my social media!
The speed square as a circ guide/speed square and box cutter to mark cross cuts will come in handy today! Thanks!
Just did a whole video on that usage, First!
Very good information and video. I have to admit that I've taken hand tools for granted. I'm a hvac and refrigeration guy my whole adult life and a home carpenter at my house. My hobby is wood working, but with hand tools and my goal is to learn as much as I can so I could do this when I retire God willing. Anyway I purchased a book called Hand Tools Their Ways and Workings by Andrew A. Watson. A very good book for information and easy reading. Thought I had it all figured out. Happy new year. Aldren A Watson.
this is the best youtube channel for learning about this stuff...your communication style is so quick and clear and you keep all this info interesting. it's just a flawless way to learn about tools and techniques
Great tricks! I use a lot of them in my woodworking. I use needle nose pliers for pulling nails as well, and twist it for extra leverage when needed.
I got two great things from this video. First, I learned some new techniques with tools I've already got. That's valuable. Second, it turns out I'm a somewhat experienced home DIYer?! Who knew? So way to go, teach me something new and make me feel smart at the same time. Well played.
You are a great teacher! If I were influential in a school district or state-wide educational program, I’d utilize you and your skills to begin a program in schools teaching REAL, valuable skills that would, over time, show up in our culture. People would be spending more money on tools and home/neighborhood improvement and less on tattoos and body piercings.😄
Tips from a perfectionist!! Thank you Ethan!
What a great video. I'm a maintenance mechanic in a college. Most of my career in shops, most guys I worked with didnt even know this much.this is like a class every maintenance guy should take
I have been practicing most of these but learned a couple of new tricks. Thanks.
I got a 3 $ looong screwdriver at Goodwill after seeing your post . Great tips!
72 years of age, have used hand tools all my life ... and I still learned a few 'new' useful tricks ... *THANKS!*
Love these tips! Doing alot of DIY projects and your tips are making it even more enjoyable!
These are great tips, and I'm thankful I grew up with a dad who taught me all these great things and more, which I had taken for granted!
Finally, the algorithm sends us something worthy!
These vids are great! Keep posting them, please. You are awesome. Thank you.
Great video. The only mini hacksaws I have are just miniature versions of the larger frame type, which also dont fit into certain areas. That lockable handle for a full size blade would be incredibly handy. 👍
I appreciate these videos types of videos. They are especially useful for passing on information to the next generation. I don’t always remember all the tricks on demand, but they are there when I need them.
No wonder I never got precise measurements with my tape rule, I've always flattened the rivets down tight with a hammer and punch ,tape against tab, figuring it was just a cheap tape measure! Honest Carpenter= IT'S SUPPOSED TO MOVE!!!! you just got a new subscriber!
You're not the only one. But tape measures are not terribly accurate to begin with. They'll get you in the ballpark most times though.
😂😂😂😂😂
Used many of those tools before but didn't know about all the features. Learned a lot in a short time. Thank You!
A good addition to your video would be explaining the many uses of a speed square, finding angles etc. Its crazy what can be done with one.
I inherited a tool chest from my dad and you've been really helpful with a few of the tools in there!
Already killing it coming out the gate in 2021! Cheers!
Needle nose pliers holding a small nail was a good trick for me! Thanks!
This is so brilliant I loved these experienced tips and tricks of the trade, I learn so much from your how to use these tools videos, its essential to know how to use the tools correctly and safely I really appreciate these types of informative demonstrations it's so valuable knowledge, I'm a very inexperienced DIY-er I can use a drill put up shelving but I lack knowledge of what tools to use and how to use them, I really dont know how to operate handsaw tools, as I've never used them before, but I would love to learn and feel more competent and confident, your channel is excellent I'm loving it all, please keep it coming, do you have any videos about how to use jigsaws, bandsaws and what's the best way to cut circular projects in wood what's the best tool for that? Thank you new subscriber Laura in England
The nut drivers in the end of the 3 in 1 screwdrivers was something I never knew and I've been using those things forever. Thanks!
You’re welcome, locked! 😄
Great stuff! My favorite is usage of long-nose pliers to hold small nails. +1 comment made re: slip-joint back jaws to cut stuff. Two additions not already mentioned in comments by others:
* Instead of screwdriver to turn eye bolt, you can also use Crescent adjustable wrench for a different handle angle and for more contact with eye bolt
* The back side of long-nose pliers have high leverage flats that can be used to crimp stuff (in a pinch ;-)
Love this expert. 72 yo diy'er female from Adelaide South Australia. Always learning from this page. 😊
Good job - one of the best of the year. I lookk forward to seeing where you take this channel in the new and hopefully more pleasant year.
Thank you, Randy! I'm hoping for a better one as well--but definitely looking forward to taking the channel on to bigger things. Thanks for watching!
Excellent video! Keep them videos coming for all us DIYers !
You can also use shaft on 6 in 1 screwdriver to extend hex shank drill bits. This is something that has saved me many times when your drill bit is just not long enough.
What are you talking about? hex shank drill bits are usually short. They just fall into the shaft.