Install Baja Designs LP4 LED Lights to Uptop Overland Alpha Roof Rack Installation Instructions

[@bertswitten372]

Very nice video 👊

[@AdventureSquadOverland]

Thanks ✌

[@Ed-sh8jt]

Does Alfa roof rack manufacturer not sell or make the windscreen cut-out for the LP4 lights?

[@AdventureSquadOverland]

Yes I purchased the windscreen with LP4 cutouts from uptop overland, same manufacturer

[@Ed-sh8jt]

Thanks they look great! also on the 14:04 video shot of cable harness connected to back of light fixture. You could have added some black heat shrink help protect the wires and adds a little better look

[@AdventureSquadOverland]

Thanks. I got lazy tho lol. I’m actually changing the entire setup hopefully by winter 2024 💪🏼

[@jodywatkins1037]

Do you have a picture of the wire harness and how you made it. I'm getting ready to install the same setup. Was told by Baja that I could use 12 gauge to run 4 lights but I was thinking it should be 10 also.

[@AdventureSquadOverland]

Yes google amps per ga and u will see we are correct. Don’t risk ruining your gear. I don’t have a pic but what I did was run a wire the length of the LP4s all the way to my switch pro with an extra foot of wire. Then measure the distance between each LP4 and mark it on your 10 ga wire. From there I connected all 3 ends together, or u can connect 2 ends together and then connect that wire to another end (3 ends total). Just make sure there is plenty of surface area contact and make it water tight. Hope this helps, good luck, wish I was there to help 💪🏼

[@VWdjs]

What did you use to hide the wires? I go the KC hider but can’t fit all of the wires.

[@AdventureSquadOverland]

I just found the wiring video clips…. Ah maybe I’ll upload that video separately when I can get to it.

[@AdventureSquadOverland]

@@VWdjs I have a video on this coming in a couple weeks or sooner. Some kind of 3M wire hider I forget the name. Outdoor use tho.

[@aidanseanzabs3563]

@@AdventureSquadOverland did you get a chance to upload that wiring vid clips? about to do same set up. thx.

[@Desmo_racer]

Cool windscreen and light. Where did you get the bracket for the bar?

[@AdventureSquadOverland]

Thanks man. I love it still. The bracket came from uptop overland. When u order a specific windscreen cutout they will also include mounts. For this cutout they included the brackets. Thanks for watching and supporting bro. See u out there

[@Desmo_racer]

@@AdventureSquadOverland thank you so much. I have different rack but trying to figure out install uptop windscreen with lights.

[@AdventureSquadOverland]

Check dimensions, uptop is wider than most other racks. If creating your own, front runner setup might be easier check it out

[@Baseballpro1319]

How much amps in total does it take? Is it possible if I run the wires to a Blaze Off-Road Garmin PowerSwitch??

[@AdventureSquadOverland]

Not sure about the power switch, give them a call. Each LP4 will draw 5.5 amps. What u building?

[@caseycrick7627]

Can you tell me who you had cut your windscreen? Looking to install 8 LP4’s on a TrailRax Bronco as well as 6 LP4’s on the bumper and 1 LP4 on each A Pillar?

[@AdventureSquadOverland]

Uptop overland. They also made the rack.

[@jonnytacooutdoors]

Those lights are so bright

[@AdventureSquadOverland]

Yes, pretty hard on a cold battery tho, thinking of a dual battery setup

[@kceatc5305]

where did you get that bracket that joins the two load bars together?

[@AdventureSquadOverland]

Uptop overland. If you order the LP4 windscreen they add it I believe and make sure you have everything you need.

[@RolexDSSD]

Nice

[@AdventureSquadOverland]

Thanks

[@kseepersad2380]

First 😊

[@AdventureSquadOverland]

Thank you 🥳