Simder MIG FLUX 140, The GOOD, BAD, and UGLY
HTML-код
- Опубликовано: 6 окт 2024
- Reviewing the SIMER MIG 140 from Amazon:
amzn.to/3cG9AHt
It is a flux cor arc welding (FCAW) or gasless MIG welder)
Nozzle Gel: amzn.to/351bxuC
Welpers/ Mig pliers: amzn.to/37CAxco
Welding Gloves: amzn.to/3trCEIt
Magnets: amzn.to/3wn9vA2
Clamps: amzn.to/3uhLms2
Angle Grinder: amzn.to/3im5yDJ
4 1/2" cut of disc: amzn.to/3Iw45VQ
Wire Wheel Brush: amzn.to/3tqDAgg
amzn.to/37GN6mZ
Welding coupons and supply:
weldmetalsonli...
10% Code: MM
Reviewing the Simder MIG (gasless) 140. Thanks😀😀
On Amazon it’s $92 dollars with a $20 dollar coupon off so get it for $72.99 plus tax out the door $79.92 a no brainer for the price just to put in garage if any day need it I have one on hand. Good Review 👍🏻
What settings did you have luck with the weld? I wish I had seen this video before I bought mine, but at $62 delivered, was worth a shot - not. The volt knob can be adjusted only when you turn on the power, got to be quick. Most likely means nothing. I have tried several combos between the volts and amps and I just seem to burn. No nice welds like yours. I am using Sonnler .030. I'm new to welding, but this is crazy. Any ideas? I think I'm going to dump this and get a Titanium 125. Thanks and I really enjoy your videos!
Cheap welder that does well! All your other points are why it's cheap? Thanks for the review
Thank you!
I ordered one earlier today. Amazon discounted it 30% or $30 don't remember which. Just over $100 so if I can make the four or five little welds I need it will have been more than worth it.
Right on!
I did not like the exposed board and wires. I got the 4050 MINI for $15 more. Listed as MIG Welder SSIMDER 140A MIG/Lift TIG/Stick 3 in 1.
I appreciate the review 👍 one question, the “A” knob is the one you used to adjust wire speed? Also, would love a follow up video on how this does with stick and any recommendations on what sticks you like.
These are on sale on Amazon right now for $85!
I just picked up this welder and a arccaptian HSH-S800 for 102$
Picked this up for $85 after tax today. Fingers crossed it is decent
Hi, how has it been over the nine months that you had it? Have you used it enough to tell whether it’s good or bad?
@@jaxonburt3670 I haven't used it enough to truly recommend. The knobs being labled weird has been a huge deternent. If i was to do it all over again, id get the titanium 125 from harbor freight when its on sale
Nice video and information I am interested to buy Simder I am new to welding which model should I buy thanks in advance or any other brand which one you recommend Thanks
There are a ton brands out there. On the cheaper end I'd go with Harbor Freight, Yeswelder, Simder, ArcWelder to just name a few.
Thanks I bought simder 140 M welder in Canada best Amazon service and nice packing too
So the voltage dial is what affects wire speed? Or the amp dial?
Amp. I have had no luck with my Simder
@@richardbartlett4075 no luck as in it’s been bad?
it beats any stick welder , 0.8 and 1mm bottoms works , on 1mm wire go slower , 0.8 is faster
It’s $90 with the coupon now. Is this a better value than the harbor freight 125?
Good review
Thanks!
I just bought but mine does not feed on arc mode. Is it normal? When I touch it on arc mode wire melting instantly
Do you like this better than the Titanium 125 for flux core?
I like the Titanium 125 better.
Where can i purchase the mainboard...MIG-140
Great vid! How would you compare it to the Titanium 125 flux welder?
Titanium is better. Better settings and overall build of the machine.
Hey I know nothing about welders, is this similar to the simder 200?
I'm sure it it but I can't say for sure since I haven't had the 200.
@@-DIYPRO- thanks
Will it run 1/8" low/high?
Yes it can do 1/8". Not sure what you mean by low/high?
@@-DIYPRO- 7018 is low hydrogen or low/high.
Yea it runs 1/8 6011s
У нас в России такой аппарат стоит $60