You're getting the video balance of comedy, explanation, and fabrication pretty dialed, Y'all. Meanwhile my little baby TJ is outside just jealous as all Hell.
😂😂😂😂 Your Jeeps jealous lol I love it!! Your Jeeps get more attention than our wives around here 🤣🤣 Thank you so much for the positive comment 🙏🏼🙏🏼 we are so happy to hear your diggin the content 🔥🔥😁😁
Cross member is beginner fab shop. You welded it. Grinded it. Textured it. Next step would have been fish plating the seams you welded/grinded. . Great job.🤘🏼
I saw that crossmember interference long before you did. You must not have heard me tell you that while you were building it. I tried. I yelled at the video. Nobody listens. :)
When ever you all are working on anything , For some reason it always looks like One of you is about to get hurt pretty bad, Love you're content and editing skills, leaving in the parts where things get ScReWy , great family, showing that you all are just at like most of us !!!! "LUVINIOLDTRX"
With a manual trans there is no slip in the drivetrain like a torque converter does for an automatic. Its direct drive so I was breaking front axle shafts constantly.
Remake it in dom 120 wall tube it will take some of the space out that you need, or make a bolt in middle ans keep it striaght across allowing the drop out service
I’d you are talking about the piece that hits the tub, I’m worried 120 wall 2” tube isn’t tough enough 😬😬 knowing us it would get ripped off and we would be screwed 😂😂
Holy Crossmember Dude! Please tell me you guys don't always cut parts and fabricate on a aluminum bench? Not staged for content RIGHT? Lol Hopefully a Welding table makes it into the new shop!! Love you guys though!
Y’all should bring these bad ass rigs down south would love to watch them work in a different environment then y’all are used to but these rigs would perform really well. Love the channel and the rigs
There’s a handful of brands that make crossmembers exactly like that. Could have bought one of theirs or at least taken measurements off them. RPM steering and Hepta MFG to name 2.
You're getting the video balance of comedy, explanation, and fabrication pretty dialed, Y'all. Meanwhile my little baby TJ is outside just jealous as all Hell.
😂😂😂😂 Your Jeeps jealous lol I love it!! Your Jeeps get more attention than our wives around here 🤣🤣 Thank you so much for the positive comment 🙏🏼🙏🏼 we are so happy to hear your diggin the content 🔥🔥😁😁
8 and 2 ticks over the big one in the middle 🤦🏻♂️
Caleb reads a tape measure like I do 😂
I think most of us do, we just don't admit it😂
Awesome way to start my Sunday morning by getting to watch YOUR channel before everyone else's! 👊
HECK YES 😁😁 Thanks so much for watching 🔥🔥
You leave Jake out of the mess you`re makin`...
I really enjoy your content! Your videos are addictive!
Wow your guys channel is dialed in. Awsome content with the lol moments plus the killer editing wish i found it sooner.
Love your videos FYI you may want to look at the Smart tool angel finder. I used it to set up my rear end in a drag truck.
Man you guys got a wining lotto ticket being able to do fun stuff and get $ outta it with your brothers is unreal.
It's a really cool channel~ And great friends~!! I will always support you!!👍👍👍
thank you!
Hi , the crossmember definitely , looks manufactured , good job .
Cross member is beginner fab shop.
You welded it. Grinded it. Textured it.
Next step would have been fish plating the seams you welded/grinded.
.
Great job.🤘🏼
I saw that crossmember interference long before you did. You must not have heard me tell you that while you were building it. I tried. I yelled at the video. Nobody listens. :)
we could hear something coming from the TV but couldn't make out what it was🤦🏼♀️
What if rather than cut the seats out 😂 you made a reinforced 3 piece crossmember comes out. I mean even the factory one comes out for service
Always so much fun watching you guys fabricate 👍🏻👍🏻👍🏻
Thank you, the fabrication videos are so hard to make entertaining 😂😂😂 so thank you for letting us know 🙏🏼🙏🏼
@@PeckBrothers 😂😂😂 that’s hysterical because you always seem to be in peril when fabricating
Why not scalp the top of that rear crossmember and cap weld a new top that’s shorter and not need to cut the tub?
That crossmember is pure backyard fab shop. A fab shop would have a bender to make that.
When ever you all are working on anything , For some reason it always looks like One of you is about to get hurt pretty bad,
Love you're content and editing skills, leaving in the parts where things get ScReWy , great family, showing that you all are just at like most of us !!!!
"LUVINIOLDTRX"
what about the previous manual trans was causing you to break parts?
With a manual trans there is no slip in the drivetrain like a torque converter does for an automatic. Its direct drive so I was breaking front axle shafts constantly.
What Bumpers are you using?
Why scrap the ORI’s?
looks great brother,better then what id lay down
I laugh way to much at these! Man it reminds me so much of working with my boys!
Lol so happy to hear this 😁😁🔥🔥 Thank you so much for watching 🙏🏼🙏🏼
Love you guys! Thanks for posting.
Absolutely! Thanks for the support!
He expects to work on it as much as Caleb works on his Jeep
What is the wheel base?
Is good that you guys have eachother to work with the jeeps and come up with the best ideas posible for killer jeep mods 😅🤣🤣🤣
Honestly it helps so much to have 3 sets of eyes on stuff!!!! Thank you so much for watching 😁😁
Thanks for the new episode. Love the content and the builds.
Remake it in dom 120 wall tube it will take some of the space out that you need, or make a bolt in middle ans keep it striaght across allowing the drop out service
I’d you are talking about the piece that hits the tub, I’m worried 120 wall 2” tube isn’t tough enough 😬😬 knowing us it would get ripped off and we would be screwed 😂😂
Holy Crossmember Dude!
Please tell me you guys don't always cut parts and fabricate on a aluminum bench?
Not staged for content RIGHT?
Lol
Hopefully a Welding table makes it into the new shop!!
Love you guys though!
That aluminum bench is the best fab table we have at the moment😂
Love your channel. Keep’em coming!
Will do 🔥🔥 Thank you so much for watching 😁😁
Monkeys and a football comes to mind watching the vice action 😂
Looks like Peck Brothers Fabrication
seems right🤔
Best Jeep content on the Tube!
You all are awesome 👌
Y’all should bring these bad ass rigs down south would love to watch them work in a different environment then y’all are used to but these rigs would perform really well. Love the channel and the rigs
We 100% plan on coming down south 😁😁😁 the question is when on earth we will be done working on them 😂😂
@@PeckBrothers That would be Rad, we’re never really done working on them though are we? 😂
Yall crack me up, love the videos! Hope to wheel with y’all someday 🤘🏻
Thanks for watching😁
Do trailer park residents have back yards? Nice to see you guys working on the rigs.
Good question lol I guess it depends?? 😂😂 thank you so much for watching 🔥🙏🏼🙏🏼
There’s a handful of brands that make crossmembers exactly like that. Could have bought one of theirs or at least taken measurements off them. RPM steering and Hepta MFG to name 2.
Not pure backyard but nowhere near fabrication shop lol
Cross-member looks like it was fabricated in a totally backyard fab shop!!😂😂
JK - you three rock, love the Jeeps and. Brother banter. Keep putting out videos, look forward to new ones on Sunday mornings
Thank you so much 😁😁 comments like this make it worth all the work 🔥🔥🙏🏼
You guys are a hoot! Love the clean fun and fairly good fab work lol!! Let's wheel!
Fairly good fab work 😂😂 I’m honored 🤣🤣🤣 thanks so much for watching 🔥🔥
Keep em' coming!
10-4 🫡🔥🔥
Fabrication shop
I am sure this has been asked and explained. Is there an actual Dean and is he perfect?
Have you ever met a bad Dean?
You need plywood or sheet metal on your concrete or the sparks will screw the finish up
Little bit of discoloration and burnt never hurt no one 👀😂😂😂 #sorrybrade
Someone enlighten me.
What is a: Dean; Dien, ding?
Just curious never heard anyone say that.
Just Dean It!
America 🇺🇸 💪🏼🤙🏼
That crossmember looks like my blind grandmother who also has Alzheimer’s welded it up. 😂 totally kidding
😂😂 youre not too far off😉
Looks Farm Fresh 😂😂😂
YES 😂😂😂😂😂😂
That's a lot of bends for a crossmember. I'd take that off and sell it to McDonalds