I used this pump to replace the pump on a Ecell 3100 PSI pump. ruclips.net/user/postUgkxEU8wdEWW31diRsOawsCNfWEho39M27qd The model # is PWZ0163100.02 for those looking for a matching pump. It went on very easily - 10 minutes at most. Feels like a lot more power than the original but that's to be expected. Can't tell a difference when cleaning with the wand or floor sprayer. Would recommend as it was cheaper than most I found. The maintenance free aspect is definitely a plus too. Have used it through about 6 tanks of gas and have zero issues so far.
Audience, but don't mean to be so bold. This gentleman is key on his information. He is on perfect point throughout this video. Tell your company to give you a fifth raise for the year, with 5 stars....You are a true "PRO"-Fessional.....
Awesome video, thank you. I have a couple questions, I have a excell pressure washer with a professional series6600 with a 5.5 hp honda gx160 motor an 2200psi with 3 Gpm. So the questions now, I replaced the unloader valve an the instructions said to adjust until I didn't notice a change in pressure an then back it down an tighten nut, but if I adjust it to 2200, it still can go higher but after about 15 the motor starts to struggle so I hurry an back it down. Should I only goto 2200 no matter what even if it still gives more pressure? An also what size orfice fitting should i be using for my washer? I got it with the broken unloader so I nothing to compare it to as far as how it used to run. But I will say it seems like its more powerful than another pressure washer that had 3000psi. Oh an i also see the psi number with the guage i purchased. Thank you for your help
What brought me here was to verify that the bypass hose and connector do not have to be the high pressure kind.... just regular hose and hose clamp are sufficient.
This is a great video - all in one place. I would like to see a video on what hoses go where. I am sure mine is set up incorrectly: the detergent somehow ends up going through the pump and into the holding tank!
My pressure washer is 4 gallons per minute with a belt drive. The unloader is pulsing up and down with a banging sensation. Any idea why that is? Thanks
Pressure Washer Unloader Valve it stops when i let go the trigger but when i open the with the black nut it runs ok it down some on power will i do more damage if i keep using the washer
Some of the lesser expensive pressure washers use thermal relief valves. I'm wondering if these can be replaced in some way to redirect the water into a tank. This unit seems to be made to do that, but some just have this water heater type valve. Is there a way to modify these lesser units to recycle the hot water away from the pump?
My wand allows two setting of a high pressure and a lower pressure setting and also allows an orifice adjustment for spray patterns. It seems that when in the high pressure setting the machine works fine with plenty of water spray but when I go to the lower pressure setting on the wand the pressure is less than the garden hose feeding the machine. Is this a indication of a bad unloader? The engine runs fine at any pressure setting.
What would the symptom be if the water volume was too low? My washer seems to “ lose prime” and then work for 30 seconds to a minute then lose prime again (low pressure).
I know right. it's clockwise to increase pressure. 😎 just don't over do it. keep the pressure to the recommended psi for your machine. my machine is 3000 psi and I set it to 3200 but no higher.
HI I have a Landa Mhp4-3500 hot water 3500 psi 3.5GPM. I put the gauge there and the pressure is around 1500psi basicaly i lost 2000psi. Do you think the pump is bad or the unloader?? One more question....for the hot water the unloader is close to the pump or after the heat water container that release the hot water to the hose and water gun??? Thanks
you should be using a #3.5 orifice nozzle for the size of your machine if those are 3.5 US gallons. If that's not it you can always try to adjust your jam nuts as described in the video. clockwise for more pressure. but if you feel like you have good pressure but the gauge says you don't, then you need a new guage. hope this helps
my 35000# pressure washer from northern tool , will, run fine using the soap noozle, but when i put high press' noozle on it'll run afew minutes then quit, but will start again an d run another few minutes and quit, i disabled low oil pressure switch, to eleminate that problem. any idea what is causing this problem?
Question: I have low pressure with cavitation of water. Have oil spurting out of my red air vent cap when pumps on. Have Cat 3200psi pump. 3.5 GPM. US gallons Had the PW unit since it was new, it is now 19 years old. Had unloader replaced a few times. Is it possible that its a bad unloader causing the oil to come out of the vent cap? Thanks, Note: Live in Florida, USA where water is hard.
Hello can you please help me? I really enjoyed your video, however I'm still confused on what's going on with mine. I have a 3700 psi 4gpm Honda gx390 that doesn't feel like it's reaching max pressure. I hooked a 5000psi guage exactly how you had it on your video, when I start mine up I see the needle on gauge rises between 3700-3900 then slowly decreases to 2500. Once it hits the 2500 it will then peak back to the 3700-3900 range. Once I squeeze trigger for the water to expel on the wand using a 0 degree nozzle I only show 3000psi on my guage. What do you think this could be and I did buy this used. Thank you so much thank
Pressure on your machine is properly measured at the gun end of the hose. not directly off the pump. The rating of your machines pressure is measured with the trigger closed[not spraying] the pressure when the trigger is depressed is the working pressure and not how manufacturers rate their machine. I work on these things as well as other equipment and am certified by all the manufacturers in case your wondering.
I used this pump to replace the pump on a Ecell 3100 PSI pump. ruclips.net/user/postUgkxEU8wdEWW31diRsOawsCNfWEho39M27qd The model # is PWZ0163100.02 for those looking for a matching pump. It went on very easily - 10 minutes at most. Feels like a lot more power than the original but that's to be expected. Can't tell a difference when cleaning with the wand or floor sprayer. Would recommend as it was cheaper than most I found. The maintenance free aspect is definitely a plus too. Have used it through about 6 tanks of gas and have zero issues so far.
Audience, but don't mean to be so bold. This gentleman is key on his information. He is on perfect point throughout this video. Tell your company to give you a fifth raise for the year, with 5 stars....You are a true "PRO"-Fessional.....
Best video on this subject. Thank you for posting.
Best unloader valve replacement video out there. Great instruction!!
Thanks mate! Only good video on the web that shows how to do this properly! Nice work! Very much appreciated -- from Western Australia!
One of the best tutorials . Thanks.
You are an excellent instructor! Thank you
Excellent video both from an information standpoint and production quality. Thank you!
Awesome video, thank you. I have a couple questions, I have a excell pressure washer with a professional series6600 with a 5.5 hp honda gx160 motor an 2200psi with 3 Gpm. So the questions now, I replaced the unloader valve an the instructions said to adjust until I didn't notice a change in pressure an then back it down an tighten nut, but if I adjust it to 2200, it still can go higher but after about 15 the motor starts to struggle so I hurry an back it down. Should I only goto 2200 no matter what even if it still gives more pressure? An also what size orfice fitting should i be using for my washer? I got it with the broken unloader so I nothing to compare it to as far as how it used to run. But I will say it seems like its more powerful than another pressure washer that had 3000psi. Oh an i also see the psi number with the guage i purchased. Thank you for your help
I have found SEVERAL different unloader valves are used depending on the unit.
عايز طرمبة زى دى للتميزر
Great video!, One of the best I have seen. Thank You!
Great video, very well done!! Very concise, clear instructions with excellent video to accompany the instructions. Thanks!
This is the guy who does all Corp training videos..
Very informative. Thanks for taking the time.
What brought me here was to verify that the bypass hose and connector do not have to be the high pressure kind.... just regular hose and hose clamp are sufficient.
This is a great video - all in one place. I would like to see a video on what hoses go where. I am sure mine is set up incorrectly: the detergent somehow ends up going through the pump and into the holding tank!
How about if the engine stalls when you pull the trigger?
Thanks in advance.
Aloha Scott
My pressure washer is 4 gallons per minute with a belt drive. The unloader is pulsing up and down with a banging sensation. Any idea why that is? Thanks
I thought you could just turn the black knob either way to adjust pressure. So you have to actually take it off and do it with the two nuts???
Amazing video. Amazing 🤩
Pressure Washer Unloader Valve it stops when i let go the trigger
but when i open the with the black nut it runs ok it down some on power
will i do more damage if i keep using the washer
In agreement with everyone else.
Great video! Very informative
Excellent video
Some of the lesser expensive pressure washers use thermal relief valves. I'm wondering if these can be replaced in some way to redirect the water into a tank. This unit seems to be made to do that, but some just have this water heater type valve. Is there a way to modify these lesser units to recycle the hot water away from the pump?
My wand allows two setting of a high pressure and a lower pressure setting and also allows an orifice adjustment for spray patterns. It seems that when in the high pressure setting the machine works fine with plenty of water spray but when I go to the lower pressure setting on the wand the pressure is less than the garden hose feeding the machine. Is this a indication of a bad unloader? The engine runs fine at any pressure setting.
What's a shutoff gun?
Thankyou, very well explained.
What would the symptom be if the water volume was too low? My washer seems to “ lose prime” and then work for 30 seconds to a minute then lose prime again (low pressure).
Or air in the line
what if you have too much pressure and want to lower it?
He said the jam nut is to be turned clockwise to increase pressure and then said turn it counter clockwise to increase pressure. ??? Which is it?
I know right. it's clockwise to increase pressure. 😎 just don't over do it. keep the pressure to the recommended psi for your machine. my machine is 3000 psi and I set it to 3200 but no higher.
Is the barb fitting and bypass hose 1/2 inch size?
How do u know that your old unloader is putting out enough pressure because of 2 screws you adjusted on the top of the unloader
I think the word is "displacement"
Appreciate the info. Great help.
HI
I have a Landa Mhp4-3500 hot water 3500 psi 3.5GPM.
I put the gauge there and the pressure is around 1500psi basicaly i lost 2000psi.
Do you think the pump is bad or the unloader??
One more question....for the hot water the unloader is close to the pump or after the heat water container that release the hot water to the hose and water gun???
Thanks
you should be using a #3.5 orifice nozzle for the size of your machine if those are 3.5 US gallons. If that's not it you can always try to adjust your jam nuts as described in the video. clockwise for more pressure. but if you feel like you have good pressure but the gauge says you don't, then you need a new guage. hope this helps
Well done, thank you for the time.
Thank you Sir
What is a " shutoff gun"
my 35000# pressure washer from northern tool , will, run fine using the soap noozle, but when i put high press' noozle on it'll run afew minutes then quit, but will start again an d run another few minutes and quit, i disabled low oil pressure switch, to eleminate that problem. any idea what is causing this problem?
very informative thanks
Good information and video, but don't use crescent wrenches if you don't have to.
Question: I have low pressure with cavitation of water. Have oil spurting out of my red air vent cap when pumps on. Have Cat 3200psi pump. 3.5 GPM. US gallons Had the PW unit since it was new, it is now 19 years old. Had unloader replaced a few times. Is it possible that its a bad unloader causing the oil to come out of the vent cap? Thanks, Note: Live in Florida, USA where water is hard.
Sounds like to much oil, or water has gotten in the pump . Either way there is to much something
thank
Excellent video! Thanks!
11:25 through 11:40 is the only thing I know how to do.
If people need to be talked too like a 5 year old maybe they should not be near a pressure washer.
Very Helpful Thanks
where does bypass hose go to
Joint suction side
Btw the pump I have a a company called general if that helps
hi could you help please i am trying to start the washer by pulling the cord it keeps flying back in i changed the cord but this still did not help
+Samie Hall Not a permenert fix, but try to hold the trigger of the gun whist starting it, I found that this stops the kickback.
When pulling the cord hold the trigger on the wand open.
disculpen pero creo q esta bien la explicación pero seria bueno en español gracias para mejor comprensión gracias
Thankyou.
Hello can you please help me? I really enjoyed your video, however I'm still confused on what's going on with mine. I have a 3700 psi 4gpm Honda gx390 that doesn't feel like it's reaching max pressure. I hooked a 5000psi guage exactly how you had it on your video, when I start mine up I see the needle on gauge rises between 3700-3900 then slowly decreases to 2500. Once it hits the 2500 it will then peak back to the 3700-3900 range. Once I squeeze trigger for the water to expel on the wand using a 0 degree nozzle I only show 3000psi on my guage. What do you think this could be and I did buy this used. Thank you so much thank
Good
Pressure on your machine is properly measured at the gun end of the hose. not directly off the pump. The rating of your machines pressure is measured with the trigger closed[not spraying] the pressure when the trigger is depressed is the working pressure and not how manufacturers rate their machine. I work on these things as well as other equipment and am certified by all the manufacturers in case your wondering.
Nice
I wonder who disliked this video?
yup
N.N.M.Makwana
وت ذافك