Here's how to make an engraving and cut with AtomStack using lightburn!! Website link: bit.ly/3P24Evp Product link: bit.ly/3HaAyUJ Amazon product link : www.amazon.com...
Don't use the "iLaser" device type, it should be "GRBL" for the AtomStack. LightBurn should no longer false-detect the iLaser from version 1.3.00 (December 08, 2022)
Hey, thank you, I'm with the Atom stack a20 pro. The setting for the $30 was on 255. As per your guide, It's now on 1000 and cuts like butter. Before this, it was so lame.
Great information for a beginner like me. But remember, most of your audience are beginners, slow don the narrative a little bit and try to limit the mouse fluttering all over the place. I had to stop and go back dozens of time to get exactly what your were doing.
Thank you! I have an Atomstack S20 and I followed your instructions and included a photo of my children, which I set to Sketch. The Sketch/photo and the Font/word I chose is fantastic, however I will have to increase the power to cut through the line and hole. Because it was a test I flipped it over and tried Dither on another two photos - one was too dull looking, the other was the photo I initially used as a Sketch, however, I changed it to Dither and as the background was quite dark it burnt a lot away. Was a good learning curve for me. Thank you again!
Hi, i did evertything you said but I have a problem when I have to move the Frame. It doesn't move, it goes once right and that is it. Do you maybe know what the problem is?
Nice easy to understand video thanks. I was using GRBL but it's too complicated and doesn't find my saved files, the good thing was that you could centralise the laser on to your work by turning the laser on, is there a way you can do this with Lightburn please?
Hello. Did you input Libraries in the controller using Arduino DE before you set it up in Lightburn? I unput libraries in Controller and then i installed the drivers outside of the LaserGRBL and then I pressed to find my Laser in Lightburn and it couldnt find it. Can you help please? Thanks!!
Hi, I have an atomstack s20 max. The power of the laser is 18-20w. They cannot cut plexiglass (acryl) 3 mm at all. Is the problem that the laser power is low, or did I not set good parameters for cutting? I use the lightburn program
The AtomStack S20 is a blue laser. Clear plexi does not absorb blue. It passes right through. To engrave / cut clear plexi - you will need a different laser. People usually use a CO2 laser because it is a far infrared beam. at that wavelength,, the acrylic completely absorbs the energy. Unlike blue that passes right through,, the plexi can't pass the IR and it absorbs the energy letting it engrave / cut.
Love your videos , helped me get to burning and etching . I have a issue though , I hit the X on all the stuff on the right and cant figure out how to get it to show back up . 😅
@@md.asrafulislam1436 go to the console and ask it. Type in $$ and hit enter. Register 30 ($30) will tell you the value to fire the laser at max power.
No matter what I do, I cannot get my m50 Pro to connect to LB. It powers up, but doesn't go to home. The control pad lights up but is just a blank white screen. I tried contacting the company a couple days ago.
I’m trying to engrave a 2 1/2 x 3/4 acrylic piece but when I click frame just before cutting it takes off and and grinds against the actual frame of the atomstack. Any suggestions on how to keep it from doing that?
I did I also changed start from under the laser tabs. It worked now just gotta make sure to get the positioning just right when I frame it. Any tips? I liked and subscribed btw Thanks for the help!!
Hi there need help, i setup mine wrong. I have a Burnlab A10 Pro but i believe it’s the same as yours only i entered the wrong working space n now it grinds up against the bar wanting to go past it. How do i change that and i also have it set to in/mm/m under diode. Should i change that to mm/s under CO2? I’m so lost 😢.
@@brakthehun how do you connect right? I used the usb and it still won’t recognize? Is my max too old is that such a thing? It’s driving me nuts! It’s telling me to save to sd card? How do you save from lightburn? Help! Lol
My atom stack p7 30w can’t be found by my computer or light burn. Idk what the deal is.. but not sure what do from there… is there a printer update I need to make or a driver bit I need?
@@brakthehun older iMac I think 2016 or so. Not sure the o.s. But I also tried it on my dell desktop and it didn’t show anything. Not sure if it is supposed to show up a printer would.
@@brakthehun I just want to save the files to the sd card after I design it from laptop I don’t want to connect my laptop to the laser because I placed my laser on our outdoor balcony. Which file type the sd card can read? I tried PNG and SVG and it didn’t work, only their test files which are NC files.
Would be nice to have detailed info on how to align the wood under the correct point [left & right etc} for starting the engrave/cut. Maybe next time?
Don't use the "iLaser" device type, it should be "GRBL" for the AtomStack. LightBurn should no longer false-detect the iLaser from version 1.3.00 (December 08, 2022)
Hey, thank you, I'm with the Atom stack a20 pro. The setting for the $30 was on 255. As per your guide, It's now on 1000 and cuts like butter. Before this, it was so lame.
Great information for a beginner like me. But remember, most of your audience are beginners, slow don the narrative a little bit and try to limit the mouse fluttering all over the place. I had to stop and go back dozens of time to get exactly what your were doing.
Thank you! I have an Atomstack S20 and I followed your instructions and included a photo of my children, which I set to Sketch. The Sketch/photo and the Font/word I chose is fantastic, however I will have to increase the power to cut through the line and hole. Because it was a test I flipped it over and tried Dither on another two photos - one was too dull looking, the other was the photo I initially used as a Sketch, however, I changed it to Dither and as the background was quite dark it burnt a lot away. Was a good learning curve for me. Thank you again!
I'm glad this helped you. Good luck!!
This is the exact information that I was looking for. Thanks!
ok, can you please also show me how to connect the Atomstack to the computer via Wifi ?
This is the most useful AtomStack video on RUclips. Only I know how much material I wasted before I came across this video xD
Hi, i did evertything you said but I have a problem when I have to move the Frame. It doesn't move, it goes once right and that is it. Do you maybe know what the problem is?
Nice easy to understand video thanks. I was using GRBL but it's too complicated and doesn't find my saved files, the good thing was that you could centralise the laser on to your work by turning the laser on, is there a way you can do this with Lightburn please?
Hello. Did you input Libraries in the controller using Arduino DE before you set it up in Lightburn? I unput libraries in Controller and then i installed the drivers outside of the LaserGRBL and then I pressed to find my Laser in Lightburn and it couldnt find it. Can you help please? Thanks!!
Great explanation . thanks so much
very good video but why is the x axis 410 cuz im pretty sure the work are is 400 x 400?
Yours might be slightly different than mine.
Geeze, when clicking on a menu item, SLOW DOWN, Tell us the name of the menu item and make a tiny circle with the mouse.
I have a new atomstack A5 pro but my laser unit is different to the one shown here.
This is the M5 I believe. YOurs may not have a homing cycle
Hi, Excellent video, just one question, what do you type to log into the console to check the s value? the video is not clear
Hi, I have an atomstack s20 max.
The power of the laser is 18-20w.
They cannot cut plexiglass (acryl) 3 mm at all.
Is the problem that the laser power is low, or did I not set good parameters for cutting? I use the lightburn program
The AtomStack S20 is a blue laser.
Clear plexi does not absorb blue. It passes right through.
To engrave / cut clear plexi - you will need a different laser.
People usually use a CO2 laser because it is a far infrared beam. at that wavelength,, the acrylic completely absorbs the energy.
Unlike blue that passes right through,, the plexi can't pass the IR and it absorbs the energy letting it engrave / cut.
@@brakthehun THAN YOU
Love your videos , helped me get to burning and etching . I have a issue though , I hit the X on all the stuff on the right and cant figure out how to get it to show back up . 😅
Open up the window menu up top and restore defaults.
How to set power max and powre min, only power max comes in my apps
@@md.asrafulislam1436 go to the console and ask it. Type in $$ and hit enter.
Register 30 ($30) will tell you the value to fire the laser at max power.
great introduction for beginners like me. Thanks a lot
Mine is not finding Atomstack S10Pro. I set it up manually but it is still not finding it. Stuck on Waiting for connection... in console.
What type of computer??
Any good suggestions for my same, not being able to find laser setup?
No matter what I do, I cannot get my m50 Pro to connect to LB. It powers up, but doesn't go to home. The control pad lights up but is just a blank white screen. I tried contacting the company a couple days ago.
Have you tried different com ports??
Have you tried installing the CH340 driver??
Yes to both @@brakthehun
When I hit play on my A5 the leader moves to the start point, but then just stops, it doesn't even fire the laser at all. Any suggestions?
Try turning off overscan in the layers??
Check your preview button??
HI Anthony >> I am new bout Atomstack x30 do offer one on one training session
Anatoly Hello i need a help , my laser x20 pro consule get warrnings pls help me to fix that . Pls copy ur consule full and paste here .. thanks
How did you get your computer to connect to the x20?
Please what will you do when your Atomstack X7pro makes noise when its moves
Do you mean it doesn't move and only makes a buzzing or clicking sound??
Is this suitable for atomstack S10 pro also?
Should be
I have the X7 Pro but the laser seems underpowered and I have my s value at 1000 any ideas?
/what are you trying to cut??
I’m trying to engrave a 2 1/2 x 3/4 acrylic piece but when I click frame just before cutting it takes off and and grinds against the actual frame of the atomstack. Any suggestions on how to keep it from doing that?
Check your preview (monitor looking button up top) make sure you have current position selected as your cut start in the lower right??
I did I also changed start from under the laser tabs. It worked now just gotta make sure to get the positioning just right when I frame it.
Any tips?
I liked and subscribed btw
Thanks for the help!!
Great Video, thanks,, now this is where I can understand what you did, thanks
Has anyone had a problem getting the fire button to operate ? It’s enabled at 25% but it still doesn’t work
Useful information well presented. Thank you.
I am trying to do this tutorial and my project is saying 35 mins! Complete newby! Can you help ,me?
I see. I might need to see your actual file.
You can try to change your engraving settings around.
brak_the_hun@yahoo.com
ruclips.net/video/t9Dkq_RGAao/видео.html
This video shows some tip
Hi there need help, i setup mine wrong. I have a Burnlab A10 Pro but i believe it’s the same as yours only i entered the wrong working space n now it grinds up against the bar wanting to go past it. How do i change that and i also have it set to in/mm/m under diode. Should i change that to mm/s under CO2? I’m so lost 😢.
Awesome, thanks dude!
do you have to have bought the actual software for it be recognized? or can you use the trail version??
You can use the trial version. If everything is connected right,, it should detect it.
@@brakthehun how do you connect right? I used the usb and it still won’t recognize? Is my max too old is that such a thing? It’s driving me nuts! It’s telling me to save to sd card? How do you save from lightburn? Help! Lol
My atom stack p7 30w can’t be found by my computer or light burn. Idk what the deal is.. but not sure what do from there… is there a printer update I need to make or a driver bit I need?
What computer??
@@brakthehun older iMac I think 2016 or so. Not sure the o.s. But I also tried it on my dell desktop and it didn’t show anything. Not sure if it is supposed to show up a printer would.
@@Philipmgabler
Try the CH340 driver from AtomStack
www.atomstack.com/software/
@@Philipmgabler Not exactly. It should show up as a COM port on the Dell or a modem on the Mac
great tutorial
Are you using mac or windows? I have a macbook pro and am looking for help
Windows. It might show up as a modem.
www.atomstack.com/software/
Try the CH340 drivers for Mac
Very helpful. Thx.
so it needs the usb cable from laser to laptop? it will not work through wi-fi only? I mean wire less
This model does,, yes.
There are USB-C to USB-B cables on Amazon.
@@brakthehun I just want to save the files to the sd card after I design it from laptop I don’t want to connect my laptop to the laser because I placed my laser on our outdoor balcony. Which file type the sd card can read? I tried PNG and SVG and it didn’t work, only their test files which are NC files.
@@pauljudesacmar7275 Click save Gcode and save it as .nc (Same panel as the play and pause)
@@brakthehun So from lightburn I can save it as or export to .nc file ?
@@pauljudesacmar7275 yup.
Thanks!
👍👍thanks great intro video
Elinize sağlık alt yazı larda dil seçeneğine TÜRKÇE yi de eklermisiniz
Çok üzgünüm. Bunu nasıl yapacağımdan emin değilim.
Excelente