Que chingona!!! Mine did 245 wheel hp on long tubes,cold air,91octane 4:10 gears. Looking forward on this cam set up and E85 tune. May I add I have my truck on a long travel kit king shocks and 37" Toyos
Just installed chopa on 5.3 2015 Silverado, keeps stalling, and hard to crank over after warm up, have to keep the gas pedal down in order to start. any suggestions to properly tune it?
It’s clearly TSP’s answer to the truck Norris cam, so they will be comparable. Any margin of gain or loss from either would be negligible. Glad tsp did this tho for sure! They needed a cam to compete with the truck Norris! All around best NA cam for a 4.8 or 5.3 IMO
Disculpa que arbolito es? Me gusta el sonido para la mia también le cambiaron el convertidor de la transmisión o que mas se le modifica o con ese arbol no se necesita?si me pueden ayudar por favor Gracias
Did it have a stall added or heads? I had purchased a cammed and heads 07 4.8 but the owner never did the stall so it’s my next mod and posi rear end then I can get tuned cause it keeps stalling when in park and revved but won’t stall moving so I’m guessing it’s still a bad tune from Split
Depends , DD , 2wd , do you have gears/LSD Would you be interested in installing a stall ? I like the 218/226 113 LSA or the 226/232 114 LSA from TSP Both are really good for 6.0 N/A DD
Stock is fine for a daily driver, if you plan on going into the trans anyways do a stall. Have this cam in my 02 vette and it doesn't really come alive till around 2800-3k. Regret not doing a stall while trans was being rebuilt.
I have a question I’ve got a 08 5.3 I’m getting this cam and a dod delete kit for my truck I have been told that there is something to do with the trans blowing up because of to much pressure is this something I will have to worry about if someone could get ahold of me or something that knows more that would be awesome
@@jesusshinojosaa that year did not have dod so yes stock pushrods and lifters can be used. I’d swap some ls6 or ls2 valve springs in if you go with this cam.
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
I don't speak a word of Spanish and still watched this video from start to finish 👍🇺🇲
Horsepower is universal 👌🏽👌🏽 had to listen to him say chop-acabra on repeat
@@CodyHussey433 me too. Lol. I'm about to order one!
Good girl
Me too! Sounds bad ass mijo!@@CodyHussey433
❤ it!
Just got it install and dyno on same engine
Love it
Im running 35’s on 24 on 7.5 lift
268hp
Que chingona!!!
Mine did 245 wheel hp on long tubes,cold air,91octane 4:10 gears. Looking forward on this cam set up and E85 tune.
May I add I have my truck on a long travel kit king shocks and 37" Toyos
Those 37”s hurting HP. But this cam will give you a good gain of power and torque.
@@Elvis55 For now just a cam and e85 should do,6.2 and 4l80e in the near future. Great content carnal,keep up the good work.😎✌🏻
Bro you should have 4.88 gears or 5.13's even 37's are ridiculously heavy for a 5.3. Would definitely be a whole different truck after 👍
Just installed chopa on 5.3 2015 Silverado, keeps stalling, and hard to crank over after warm up, have to keep the gas pedal down in order to start. any suggestions to properly tune it?
tune
Just bought this cam it performs just as well as truck norris cam at half the price
Have been running cam Motion 216/224 108 LSA in my 4.8 and like it… specs are similar, just not many run Cam Motion in trucks seems like
What valve springs did you need to run??
@@frankdatank7751 LS .625 springs…you don’t need that much, def over kill but oh well I see most put .560
what all was installed in it and can it be installed with dod ? if not what do i have to install for it to run with dod
What type of gas mileage an do you drive this truck everyday
How does this cam compare to the Truck Norris? I see your BTR banner in the shop.
It’s clearly TSP’s answer to the truck Norris cam, so they will be comparable. Any margin of gain or loss from either would be negligible. Glad tsp did this tho for sure! They needed a cam to compete with the truck Norris! All around best NA cam for a 4.8 or 5.3 IMO
Comparable, Elvis needs a comparable truck to this one to make a video for the truck Norris we’ve been wanting to see the difference
@@wesleyhryszczuk9442 I just bought this cam for my hummer H2 6.0 I hope I get some gains on that heavy beast.
@@coyotemane trust me, it wisely be much difference. If there is, it won’t be by much give or take.
How much will it cost to do my 2013 gmc Sierra 1500,
does it have headers ?
Same injectors used?
I got an 18 L86 apart from the cam did yall need a new torque converter or anything?
How bad was the valve float on the stock springs?
Nice video. I have a BTR about same specs in a 2008 max l76 what size exhaust should I be running.
Im getting this for my 5.3 uffff sounds nice
Disculpa que arbolito es? Me gusta el sonido para la mia también le cambiaron el convertidor de la transmisión o que mas se le modifica o con ese arbol no se necesita?si me pueden ayudar por favor Gracias
Stock lifters and springs and torque converter ?
Did it have a stall added or heads? I had purchased a cammed and heads 07 4.8 but the owner never did the stall so it’s my next mod and posi rear end then I can get tuned cause it keeps stalling when in park and revved but won’t stall moving so I’m guessing it’s still a bad tune from Split
3600 stall is recommended, this cam can be ran with stock converters tho
Heads not so much a big deal but definitely get a converter
Is this better than a BTR truck noris cam. Probably about the same
Where u guys located? I have an 08 shorty Silverado. I’m in San Antonio
Nice.
Thats a pretty good gain from that small of an cam. 214/222 is not crazy by any means.
Unusual to see a 108 lsa. Was it hard to tune the idle?
What cam do you recommend for an Lq9? With a not so rowdy chop
Depends , DD , 2wd , do you have gears/LSD
Would you be interested in installing a stall ?
I like the 218/226 113 LSA or the 226/232 114 LSA from TSP
Both are really good for 6.0 N/A DD
I wanna do a camshaft like this but I keep reading I might need a torque converter upgrade too - thoughts?
Stock is fine for a daily driver, if you plan on going into the trans anyways do a stall. Have this cam in my 02 vette and it doesn't really come alive till around 2800-3k. Regret not doing a stall while trans was being rebuilt.
“Un pollito”😂😂 tenia hambre saludos desde el 602 phx le quiero comprar este cam para un 6.0 gracias por el video
Cuanto sale ese con todo el kit, con las barillas y los Springs ? y cuanto de labor ?
Llevas ls6 style springs y no push rods usas los originales. Sale en 521.00
Hi. Can you guys help me in tunning my truck thru remote HP Tunner?
I just bought this for my hummer H2. How do you like it so far?
I have a question I’ve got a 08 5.3 I’m getting this cam and a dod delete kit for my truck I have been told that there is something to do with the trans blowing up because of to much pressure is this something I will have to worry about if someone could get ahold of me or something that knows more that would be awesome
Just ordered this cam with ls6 springs, would I also have to change my pushrods and lifters??, it’s going on a 2000 gmc sierra 4.8 please let me know
Push rods cab stay with the stock ones.
What stall and gears you recommend with that cam
You can run stock stall but i think its better for a 3600 and for gears 4.11
You can run stock stall.
I subscribed and liked. Good content. In English and Spanish.
Will it blow wit a stock trans and stock seals
Stock pushrods?
Is that strait piped?
Yes, headers with straight pipe
Unpopular opinion, what was the torque difference?
Excelente video, podrias hacer un tutorial para hacer el tune con hptuners para este arbol?
That’s a nice looking truck
What lifters can I use
On a gen 3 4.8 what do you think it would do
You guys located in California?
Any yukon denali 6.2 video
Bro cual me recomiendas para un 5.3 que Jaír así como esa sin meterle mas fierros mas que el árbol
Una pregunta aun 5.3 con unas cavesas 243 con un cam el chopacabra cuanto sele saca con el tun
Bad Azz Carnal. Saludos de 956 South Texas
Donde tiene su taller primo
Good lord that’s a sexy truck
stage what?1/2/3/4
What exhaust is on this?
It sounds straight pipe
Im running a black widow on mine ,check out my vid.
Can stock lifters and pushrods be used for this cam ?
On non dod lifters, trucks equipped with AFM system (DoD) you have to swap them. AFM/DoD delete kit
@@Elvis55 what about a 2004 Silverado? 5.3
@@jesusshinojosaa that year did not have dod so yes stock pushrods and lifters can be used. I’d swap some ls6 or ls2 valve springs in if you go with this cam.
@@matthewleasure6605 thanks bro appreciate it ik it didnt have dod but wanted to know if u could use the stock ones yk
@@Elvis55 my GMC Sierra 07 4.8 has no dod so I’m good?
leave the factory underspeed/overspeed in it so we can really hear it.
I've noticed this a lot. Fake chop ruins the actual chop
Para el tsp 228r si jalara bien con una stall 2000 o necesito afueras meterle otra más grande es un 5.3 2005
228r 3,600 stall and 4.30 gears
🔥🔥
Got a 2016 Silverado z71 want the same cam on mine
Does it chop in drive?
Yes
Beast
Nice 5.3 video
Como cuanto sale un cambio de cam y tune
🔥
What springs was used with this cam?
you can use ls6 springs
You can use ls6 springs, TSP sells the valve springs kits for this camshafts
Gud shit Elvis
🔥🔥🔥🔥🔥💯
I dont know what yall are saying but i know 55+ hp improvement is great.
🔥🔥🔥🍿
I'm guessing no cats hence the check engine light..🤔
🤘
Would be badass if you made a video with the truck Norris cam from BTR
😎 we working on it.
It’s very similar to this cam so I wouldn’t see any difference. If there is, it won’t be by much give or take.
faaaaaaaaak😍
11hp to crank and 6hp to the wheels you gained
Ummm... did you watch the video? They picked up 55 whp...
Can you just buy and install the cam or do you need any other parts to make this run right other than a tune
Would it fit my 2018 GMC Sierra 5.3?
No