@@lisamarieashby2523 depends on the era. The great Giza pyramid era, they used riverboats and sleds on the sand, and wetted the sand in front of the sled. 1000 years later, they used rollers, wheels, etc, and whatnot.
Response to your question about 21 minutes in the video. The safety feature of the saw blade stop works off of a voltage differential between the trigger mechanism and a conductive media like a finger. Styrofoam sheets being cut with a rotary blade would be like rubbing a balloon against a flannel shirt. The Styrofoam creates a static charge greater than the blade safety mechanism can handle. A volt differential tripped the circuit.
i noticed this also and his finger touches the deck of the table at the instant it is triggered so i think he discharged himself as he was building up a static charge from the foam as you said
There's also a relationship in electrical conductivity in foam as it undergoes a phase change due to heat from friction. This can be unpredictable in modern foam products. Not sure if lowering the speed of the saw blade is an option.
Right? What a pain in the ass thing to request. You don't truley know what your wood is gonna look like until the finish is on and its in your home. He should have let them pick the slab and then quit worrying about it.
I had a client request an Ash and Rosewood end-grain table that looked amazing... and then they wanted me to finish it with Rubio Monocoat Silver. Ugh. We finally came to a compromise we both could live with.
I can't believe I've just spent 25 minutes watching someone make a table, what's more surprising is how interesting it was, great work and fantastic table.
Snap! I didn't even know epoxy tables were a thing, until now. Fascinating video though. If you like woodworking, worth checking out ruclips.net/user/EpicUpCycling - he makes some fascinating furniture out of old pallets... although the pallet made in this video would probably have him scratching his head! 😂
Professional epoxy installer here with over a decade experience. Those small pits that you carved out then re-filled can be completely avoided. Epoxy airates as it cures often causing bubbles (fisheyes) that pop and sink or stay above the surface. An easy and cheap method to prevent that is to use a heat gun at a moderate distance to pop them during the curing process (when it becomes tacky). I have a ton of epoxy tips for you if youre interested. Whether youre using 100 solids, polyeurethane or polyurea.
The “everything is a pain” advice you give in the content is priceless. Such a fantastic outlook. Thank you for putting out the content. Watching you channel is one of my favorite breaks from my day. Keep up the great art.
Safety tip (yay): When loading a long crate onto the back of a truck, get as close as possible before raising the forks. That way, if it does start to tip, the truck will take some of the weight and help get the balance back. I used to do this all the time with 1.5 tons of aluminium ingots. Nice work as always BTW
I’ve used a fork lift to move around coils of wire of similar weight (all metal other than the insulation), and it is definitely a little nerve wracking! I get a bit anxious even watching someone do this in a video.
@Jesus has given you all. Repent or die. Jesus blessed ALL my fork truck driving with safety. I was a choir boy and an altar boy. I don’t get people like you who think the rest of us haven’t heard of Jesus or had him bless our fork truck driving! May Yahweh bless you with safe fork truck driving as well!
Was about to say this. I work as a Lumber Department supervisor of a home improvement store and, can't stress this enough, when working with a forklift, always wait until the very last minute to raise the forks :) Good idea passing this tip along to someone who might not know what we know. I regularly lift 3000 lbs bunks of plywood and dimensional lumber daily!
That has to be one of the most beautiful tables I have seen. The work you put into making it shows that you have a real passion for what you do. I will be watching more of your videos. The people you built that table for clearly didn’t see what all your viewers saw.
I'm not a woodworker and I still love this channel, but I don't zone out at all I pay great attention to all the details and store that information in my brain. I don't know what I'll do with it but I enjoy thoroughly.
The county road commission took out a couple of walnuts 3 years ago. I said "No thanks," when they offered to haul the wood away for free and I had a guy with a portable mill come in and slab them for me. The wood has been drying for 3 years and the hygrometer says it's ready to use. This is one of the things I want to do with some of the wood. I've got to go find that step-by-step video of yours. Thanks.
@@kittykitties4220 Think of it more as seasoning. It takes a long time for the moisture deep inside the wood to evaporate. Moisture is always the enemy of woodworking-- you get rot, loss of adhesion, warping, etc. You need the wood to be the perfect moisture level before you put all that effort into it.
@@kittykitties4220 Drying time is (roughly) proportional to slab thickness, as well as environmental conditions. Where I am, it's about 1 year/inch. The next time you boggle at the price of quality hard wood, think about how long the producer has invested in it.
I think they both look great!! I also agree if they didn’t want any reddish tones they should not have picked walnut. You did a fantabulous job on both.
First time I have watched your show. My father was a carpenter but back in the day girls couldn’t even take shop classes. The boys were going to sites and actually learning to build houses. It really frustrated me. Watching this really made me want to embrace my inner woodworker. So I am!!!! I really enjoyed it!
So very true! I remember running through the door when I was in 9th grade with my schedule for the year. “Dad!, Dad!” “I got it!” He replied “What did you get ?” “I shop class!!” “Whoop Whoop 🙌 “. He replied “Good for you “, “I know you’ll teach the teacher to never cut corners and how your work reflects you !”🤭. I was only one of a few girls in his class and remember him telling my dad that he could see the sparkle in my eyes each time I came to class 🤩! Still love wood working today
Oh my gosh yes I wanted to go to carpentry school when I was in high school and my dad would not let me because there was only one in the city and they were all boys so I never got to go luckily I found I love power tools
Girls just should not go into construction as a full time job. They legitimately end up looking like dudes. I have 3 daughters, there’s no way in hell I’m letting them get into the trades. It’s smartest for women to just focus on being sweet and hot and wifely so they can find the best possible man to support them.
I lost my lovely mum 4 days ago. I'm a 65 yr old woman who has zero intention of ever building anything however I love your content & you're helping me thru a pretty awful time Thank you
PLEASE ACCEPT . I'VE BEEN WHERE YOU ARE & I GET THROUGH "LOSSES" , BY FOCUSING ON "FUNNY/FUN" TIMES THAT MAKE ME "GiGGLE". MY MOM WAS LIKE MY OLDER SISTER, & SHE RELISHED IN JOKING, NON~ADULT BEHAViOR AT TIMES. : } < MUCH LOVE & LIGHT.
Styrofoam is electrostatic material. If you pull it over your hair it’ll stand it on its ends. So, that little bit of friction created electromagnetic field which caused the sensor to go off on your saw.
My father-in-law was a Machine shop teacher, and he told me that one time when he was showing me how to pour the foam in different molds he was making. I can't believe I remembered that 55 years later. He was an excellent teacher. R.I.P
Yeah, don't cut foam in a SawStop. Use a reg table saw. Example- when you ate cutting foam it will shock you in the same way as rubbing socks on carpet and touching someone.
@@AntimatePcCustom You have to be able to afford it to pass on it. Like saying "I'll pass on dating Scarlett Johansson"; honey, it wasn't an option for you 😆
Great job, I do some woodwork on gun stocks, and a reddish hue is traditional on the finest English doubles and vintage Winchester high grade guns. These are all walnut stocks as well. There is a blend from a manufacture who has perfectly replicated this, from a 125 years ago. Be glad to pass this on, as it would be fantastic color on a large table. Great Vid.
I fall into the category of “People who watch every single of your videos with zero intention of ever building a table.” I love your format, your cadence, your candor and of course, your skill is top tier.
I don't have the space for the tools I do have, and those are just in a small (ish) rolling toolbox. If I get into one of my dream houses in the BC Interior I'll have all the space and projects I could dream of.
Okay…I am absolutely loving both pieces…omg…I wish I was not 73 and had lots of money because I would love to be able to work with wood like you do. Since I know zero about all of what you do, I am just in total awe. If you could do better,I wouldn’t know. Hard, gorgeous work that produces something that stunning is just amazing…thank you for sharing such a craft and skill.
OMYGOSH, that table was stunning. I love the look of the “live edge” with the smaller piece squared up with the epoxy … I am not a wood worker … I do not watch videos like this to fall asleep … I genuinely love watching woodworkers create what I think is art. ❤️❤️❤️
The table & leg fusion is...perfect. My God man, you are not only talented, you're a full-on artist in the highest degree. That table is optimistic jazz rhythms & beats, in corporeal form!
I am not a woodworker but I love wood and watching woodworkers bring pieces to life. I completely enjoyed watching and did subscribe. I thought the content was very interesting and the table was beyond beautiful. You are too humble and there are a lot of critics.
As an older-than-70 woodworker, I commend you for your Rock Paper Scissors contest. It warmed my day to see you caring for the next group of woodworkers
And also the fact that, because he got his new one for free, he passed that free-ness on to another woodworker. We have 6 children and I never thought I could afford a floor loom for weaving. A weaving friend GAVE one to me. When it comes time to relinquish it, it will go to another person (for free) who otherwise could never afford one. That way we pass on the joy of our craft.
@@JSCRocketScientist Your wisdom is profound. By taking the attitude of freely received; freely given, the feelings that we have in our hearts cannot be purchased for any amount of money, yet are priceless. BTW, you have me by one child ;) God blessings on you
@@michaelphelan423 Thank you! Blessings on your family too. It’s fascinating to me that the original purpose of a craft guild was to keep secret the techniques in order to protect jobs. Now our weaving guild’s purpose is to SPREAD knowledge of our craft. Which is what is being done here. It delights me.
Loved your life lesson shared, "everything is a pain" and that your wife is the reason your work is so perfect 😄 This is just beautiful craftsmanship, you are incredible ❤️
I love the handmade aspect. It shows a heap more character, and makes the piece more tactile. Your treatment of the edges are an interesting touch, too. Perfection
I watch programs like yours and refinishing programs, because I do not have the physical capability do it myself. I enjoy the artistry, the artwork and the challenge of it. When I was working I taught, and now I write. Thank you for a wonderful video.
Amazing wood working. That is one gorgeous table, and the sister to it is just as gorgeous too. You are an artist of wood working. Be proud of what you can do and did. A big thumbs up to you.
Your work is first class. If your customers knew more about wood and stain effects it would be better. Sending the examples as you did shows your attention to customer satisfaction. All the things you did for this project tells me you deserve top dollar for your product!
Better! Your videos are mesmerizing on several levels, first is your obvious passion, second is the stunning art you create, and not least by any means is your superbly crafted dialogue and tone. I found this older video that I somehow missed before and it shows that the outstanding quality of your videos remains superb.
Accidentally stumbled onto this and I am hooked! This was so informative. I am just starting to play around (safely) in my boyfriends unused woodworking garage, to take my love of “crafting with furniture” to the next level. The table is absolutely STUNNING!
I have no woodworking skills or knowledge, nor do I have any interest in learning about it - but I watched this whole video, totally hooked and enjoyed every minute of it. You're seriously talented at both your craft and making YT videos my man!
Hey Cam, great stuff as always. Regarding CNC, as you’ve said before, you are always looking for the best product to get the best outcome, and CNC should be no different. If your products are better for using it, there’s your answer.
it depends on how much enjoyment he gets out of handmaking them. if he LOVES doing it that way and only wants a CNC to make stuff quicker, he'll never enjoy the finished product, or the process, as much as he did making them by hand. and vice versa. if he hates how long it takes, he might enjoy one.
Since I started watching your channel, I won't watch any other wood working channel. I love your creations and the videos are fun, informative, and easy to watch!
For the saw stop, I’ve learned from a buddy of mine that even the slightest conductivity will set it off, which if you think about it is great until you use things conduct electricity. The reason the saw stop engaged when you were using the foam Board was because the thin layer of aluminum or whatever metal the foam board has on the top will act like a wire from your finger to the saw blade itself, thus setting it off. Best way to resolve this is to flip the board if you can so then your intact with the foam it’s self but if the material your cutting doesn’t have that then best option to use something like a glove of my preference a piece of wood to push the foam through! Great videos I’ve learned a lot about wood from them! Thanks a lot! Keep it up!!😁😁
that didn't explain why it was fine on some of the board, it cut half way through the foil side before triggering, witch I will explain by: the foil probably has a coating on it and didn't trigger a conduction until it was rubbed away enough on the wrong spot to make a conduction
Electronics engineer here. The Viper said it just right, aluminum layer on foam board conducted enough charge from your finger tip to the saw blade and triggered the protection mechanism, sorry...wear gloves next time, a couple of bucks will save a couple of hundreds...Cheers
@@tomlamb3885 every part of machine is grounded, if properly connected to mains voltage, on the part where machine was cutting fine the aluminum part was pushed against the metal parts of the machine and therefore was no conductivity between finger tip and the saw blade, the part where safety was triggered board was standing partially above the metal surface of the machine and therefore was not grounded conducting all the charge from finger to the blade triggering the safety feature...hope this helps...Cheers
Regarding the CNC question, I always use the father of a dear friend of mine, Kazuyoshi Ichiro, as my yardstick. He was a metalworker in Susono, Japan. His family had been blacksmiths and metalworkers for generations, and as proper Japanese artisans they respectfully prioritized tradition and traditional practices. However, they also used modern tools. Their attitude was that trucks and cars are more effective than carts drawn by horses or donkeys, and understanding the "why" of a tradition is at least as important as the "what" or "how". The traditional approach was to produce the best result possible with the materials, tools and techniques available, and while that led to the development of masterful skills that almost became art forms, the reason was often because of limitations in the available materials, tools or techniques. As a result, when he worked with the metal, instead of using a set of hammers and an anvil as his grandfather had done, he used a hydraulic press designed for blacksmithing. His philosphy was that the craftsman should put in 100% effort and focus to produce the best result they possibly can, using the best tools they have available. So using a CNC machine to help would be absolutely no problem, as long as the craftsman is still focussed on producing the best piece they possibly can :-)
Very well put! And make no mistake: getting CNC to actually produce the same quality as artisan work is a an art in itself!! The true advantage of CNC is not the ease of use: its the ability to reproduce without further effort. If you are making one-off shapes, an skilled worker with the right tools may well be able to put out the work quicker and more beautiful
The people that say using a CNC is cheating, or there is no skill involved clearly don't own, or know how to operate a CNC. Just like a hammer and chisel you need to know how to use the CNC correctly to achieve first class results. I built my own large CNC and I would say that is the easy bit. All the associated CAD / CAM programs and how to get the best possible result is an art in itself. While it CAN produce a better result, it isn't automatically guaranteed, you will need to master that tool the same as you do the hammer and chisel.
I'm not a woodworker, but I have been around machines and programs for years. IMHO you should know that you like programming before you invest very much. Look for simulators online or learn coding from someone who has one. If you hate it then keep doing what you're doing.
All my aunts and uncles on my mom's side were/are farmers in NW Wisconsin, and they do business with local Amish all the time, including having them make dining tables. These Amish use no power tools at all, and deliver all furniture with x2 horsepower buggies. They have no problem with you driving your pickup truck into their driveway, though, if you need to pick something up. They have very nice looking houses with no electricity or indoor plumbing. My mom didn't want to marry a farmer, so she moved to the "big city" before I was born and never moved back. They call me city slicker when I visit.
I loved the colour of the finished table - but if it was my table, I would have liked it a bit 'redder'! I really like how you preserved the irregularities of the origional slab but managed to make it smooth enough to use and clean easily. The chamfered edge on the table helped 'tame' the 'crazy raw wood look' just enough to make it civilized! The table base was great and suited the slab while it made the table 'leg and knee' friendly. Great work!
You made this all look a LOT easier than it truly is. My husband is a woodworker and I see what he goes thru. Beautiful table, we'd be honored to be the owners of a piece of artwork like that.
This guy is amazing. You can see the amount of effort he puts in to every little thing. And how he’s always thinking ab other people, great guy great channel
"I was literally addressing you specifically". That's them told. Such a fabulous table and that base is just something else. Breathtaking. Well done to it's maker too.
Hola soy Anna y te escribo desde España. No podia dormir y cayó en mis manos uno de tus videos. Yo no tengo ni idea de carpinteria, pero soy una persona curiosa y me gusta aprender y estar informada. Tu video es super interesante. Lo explicas todo con una sencillez y claridad, que da gusto seguir viendolos. Y que decir de tu maravilloso trabajo. Me encantan tus mesas. Son realmente preciosas. Te felicito. Las patas que sueles usar, son muy bonitas. Llevo mucho tiempo mirando revistas de decoracion, y en ellas encuentro patas asi o parecidas. Las que utilizaste de acero inox. son fantasticas. Seguire viendo tus videos, pues a parte de pasar unos minutos muy agradables e aprendido muchas cosas con ellos. Gracias y nuevamente Felicidades por tu trabajo. Un saludo.
Better or worse, If the client loves, that’s all that really matters. I’m a fan of the reddish hues myself. Seeing your pros & cons with CNC vs hand cut bowties would be interesting, the occasional CNC flattening would be good to see as well. All the best Cam.
Loved the video. One suggestion I would give, is to make your work table with the ability to raise the height to help save your back during some of your processes. You could probably have your friend the welder create the table and you can use a pneumatic system. You can also build a winch system like they use for boats to move those massive, heavy slabs from your truck to your work table. Many years ago my dad and I replaced an engine in my car and he built a very simple winch that was attached to wood beam He set on the two walls on each side of the garage. We were then able to move the motor exactly where we wanted it. I was lucky to grow up with a genius engineer for a dad. He knew how to solve pretty much any engineering task.
Good idea, but I would use a hydraulic lift system seems it would be more reliable when lifting heaver items. Pneumatic or hydraulic either is better than using your back, LOL
Tip: In order to eliminate bubbles / imperfections after filling the epoxy, try vibrating the whole frame. Could be an impact drill on a piece of timber, or maybe a Food Processor / blender fixed to a board on top of the table for ½ hour 👍
You do this for cake batter too, when you put the batter in the cooking pan, you bring it up about an inch and drop it. Works great, and you can always see the bubbles coming out.
He could use one of those new massage guns that are everywhere now and can be gotten for cheap. He would likely need to go around the edges of the table with it though to make sure every area gets vibrated
I don't know how I became side tracked by this video, but I'm glad I did. I couldn't stop watching it. It was so interesting to see all the steps and hard work put into such a beautiful table. Your attention to detail is amazing, and I love that your wife helps you. You should really be proud of your fine work. I admire your skills.
Same for me, Melissa. I know someone from Houston that has a table like this, and I guess that's what drew me in. Couldn't stop watching. Not a woodworker, or particularly handy, but I really enjoyed this video.
Regarding the CNC question: have you ever considered a Shaper Origin? That seems like the obvious solution to work on your large slabs, because you are not confined by the size of any machine bed. Also, they take next to no effort to "program". You load an SVG of the shape you want to cut, which you can create e.g. in Inkscape. You may have to play with the tolerances a bit to reliably achieve a "fits the first time" experience, and you have to knock out the corners yourself still. But it may speed up your process significantly.
That was my first thought especially for what he is doing with the bowties. It's not cheap but for someone doing this high end work, it might save time and therefore money. ruclips.net/video/hMgFFlDhTbA/видео.html
"I was literally addressing you specifically!" Might be the greatest reply ever!!! Thanks for another great video!! Also thanks for making all of this work seem easy. It's the people like you that make a very very difficult thing seem easy that get people like me to try doing it and then me realizing that even with my knowledge and experience it's still a very very hard trade to do! Thanks for making me challenge myself!!
@@dannymaiorani519 As a CNC machinist my self? Not with those aluminum extrusion table routers. Not even Tormach can do that and maintain a .001 repeatability tolerance. Some HAAS budget machines are just as bad. That said if you have seen a CNC do a job once you have seen it do it 10,000 times. Hand made products should stay as hand made as the person making them wants them to be.
@@viperstarpoint9 yeah I wasn't really suggesting that I was suggesting like a mill. When I had my German auto shop I bought a tree 310 from Berkeley University that they thought didn't work and I got it running and I used that. The rest of it is still hand built I've seen those bow ties sort of loosen up over time I don't know if his do. So the mill could be an improvement possibly in that regard.
Loved both colors! My husband and I have done a lot of remodeling in our home. One room at a time = no loans! Paid in full with cash on hand as we could afford each room. Thirty years of construction is enough! Almost done and I’m ready to move to a finished house, sit back and enjoy it❤❤❤!
man i love wood, just imagine nobody would ever had seen THAT particular slice, that grain pattern, hidden for decades, better than discovering a gemstone, and now revealed for people to admire like a famous painting. Bravo
I absolutely love that you are so real and are willing to show the reality of woodworking instead of cutting to make you look "perfect". That's such a disservice to folks who really want to know what's what, what to expect, and to be able to correct for mistakes you've already made. Most folks adjust and edit to make things look like they got it right the first time, and that's a shame. NO education happens.
Looks beautiful. Always move the product as close to the truck as you can before lifting it. If it does tip forward it won’t crash to the ground. You are incredibly talented and it shows in everything you do.
I absolutely love to see and watch hand-customized creations of any kind. Your explanations throughout is very satisfying. I am not a work worker by any means and I can understand most of what you are saying. What I love the most is your attention to detail. I could watch you create masterpieces all day. In addition, you are physically strong to do what you do. It takes strength to handle such large and heavy projects. I love your wife's OCD too. Her eye for fine detail is what puts the kiss of perfection on your work. I can tell she loves you because she cares enough for you, your name, and your work that she helps you to put out the best product possible. You're a great team. Thank you for sharing your artistry and skill with us.
Somehow this video just dropped into my feed so I watched it and all I can say is...you are a fastidious craftsman and your work is amazing! I’ve never seen a slab table made from start to finish, but it’s just incredible to know what goes into it! That was a gorgeous piece and I hope the client knows what it took to create that stunning work of art!
A fascinating 25 minutes that covers thousands. Having seen the start it would be wonderful, and complete the circle, to see it installed. Thank you for sharing your skills and time making the video.
Absolutely gorgeous!!!! I wish I could do things like this. When I was a little girl, I fell in love with the smell of wood as my Dad did a lot of woodworking. I inherited his carving tools and my brothers got the larger tools. Just one more thing on my endless bucket list!!
The foam probably picked up enough static that a slight increase in speed, while you pushed it through the blade, released that static and set off the stop
If there is ever any question about conductivity I always use the bypass key/function. It eliminates the safety of the SawStop but won’t trigger the stop mechanism.
I have been going through a really tough time the past couple weeks. Unfortunately I have had a lot of time on my hands. Somehow, the universe has led me to your channel and I can’t tell you how much I love it. Whenever I feel like the world is coming down on me, I watch one of your videos. I love wood working and I have learned so much from you. So from the bottom of my heart, thank you. You’re an artist and absolutely love your work.
You are not alone. I feel like in the past, people like you and i, in rough times, might go down to the local village blacksmith and carpenter to just look at them work for a while. How lucky we are.
I’m a firm believer that there is always room to improve on anything in life, but this channel is perfect. The voiceover is awesome, work is incredible. I love this channel.
If I could afford a table like that I would so order one. I love the grain and the color. When he put that black on there I was like "whoa, I don't know about this". But it turned out so gorgeous! Watching this video just goes to show that there's a tremendous amount of work that goes into constructing hand made products like this. I would love to have a handmade table but I would have a live edge on it if possible. I have wood throughout my house and love the warmth that it brings to a home. The people that bought this table will hopefully watch this video so they know how much care and love went into the table they bought. Just beautiful!!!!
"Better or worse" I just want to say thank you! I initially came here to just relax and see amazing content but I do woodworking as a hobby and I learned a ton form you. I learned how to prevent warping of the wood, gumming up of the sand paper, dealing with cracks and bubbles so basically all the problems i faced and was unable to solve when building my desk. I think it is great how you drop this information casually on the side! Concerning the bowties, I personally prefer watching you make them by hand as it is first very calming to watch someone do precision work and second it would be the only way I could do it. Ps: I love the style of your work very inspiring
I appreciate this videos contrast to the "It's so easy, it works everytime" approach to some of these craft channels. Knowing things go bumpy builds confidence in the entry of learning.
I have never watched a table being built, but this was a very interesting. I just fell into it, but I love the process. I want to be a builder. I’m an artist. It’s a form of building that I love the process and I love your devotion to perfection, thank you for being willing to share the whole story. I actually love the whole story.
I'm impressed that you are able to admit your faults. So many artists avoid the truth that we have flaws and yet they still exist. Lol your work is exceptional and congratulations on such a good informational video. *Suggestion: You don't show that you have marked the artwork with a signature, date, stamp, number or anything that accredited it to you. Please show how you prefer to signature your art, so I can identify your art pieces when shopping in the future. Eventually someone will sell or auction them off, or donate them from estates. I would love to be able to identify your "Marks"!💗💯✔ *Question: Have you followed up on the wear/care of this table? A "Where is it now!" kinda video would be fun to see. *Looking forward to more from you! Thanks for sharing- "Rock Bottom" in Ohio!
"Everything we do is a pain"- absolutely love this. I dont do woodworking or anything, but i like seeing how you guys do this stuff and the process. I am a 3D artist, and i can see the similarities between 3D art and woodworking. Obviously, two completely different crafts , but still run into problems every project. Every project is a puzzle, and that's a part of the appeal i suppose. Solving small (sometimes large) problems.
I do woodworking and I can't see any similarities. No hate but I feel like tablet "painting" and 3d printing has destroyed the craftsmanship and art of actually creating something with your hands. I can't imagine it feels nearly as satisfying when finished. Maybe I'm wrong, don't mind if there's some schooling you can take me to to change my mind?
@@heatherlee7123 There are definitely similarities to these two crafts. Besides op said 3D artist, not 3D printing, which is very different. I can say both have the same amount of satisfaction when the job is finished. It really depends on the time spent on it and what you feel about your finished work yourself. Not trying to be condescending or anything, just speaking my mind from my experience!
I love watching your videos. I'm the worst at anything and don't have a clue about what you're making. But I totally enjoy watching your videos because I learn things and it relaxes me. It amazes me that you can see what you're going to make before you start 😊. Thanks for sharing, goodbye for now.
It's lovely seeing you work. My father (who died when I was 16) worked in a foundry smelting bronze, but was also a woodworker. it was incredible as a kid watching his turn scrap wood into beautiful items that he'd sell. Watching you reminds me a lot of him, but he didn't have so much hardware because it was thirty years ago and he didn't have access to such machines. Thanks for the channel. Subbed.
Man, that's incredible! I have so much respect for guys like your dad! These guys could make stuff that they needed and took pride in what they do! I am no where near the expertise of this gentleman or your dad, but I love woodworking and building things that I want! I learn so much from these videos and people like you who share their experiences or memories! Just a humble "thank you", brother!
I think we had a friend who used the same colour on a table for his gazebo. When he first applied it he was sooo disappointed, but as he let it weather it mellowed and brightened and in the end, the table is gorgeous. I love it.
If I were in a position to have a table like that made I would honestly be quite happy with it. On the other side of the coin..... if some one can afford a $13500 table for their "dream" house they must be pretty well off so im not surprised if they actually hated the table. You still provided a table thats more than worth what you sold it for.
God bless you dear! I am a zoner and so enjoy your videos! Please don't stop for all us zoners out there you are a Godsend to watch to bring such beauty from His and your creation😊😊😊😊
Honestly one of the best tables I’ve seen! Love the color and the wood grain!, this video was in my recommendations and I don’t regret clicking on the video! Absolutely love your whole process and set up! You’ve earned a sub from me! Keep up the great work! Excellent craftsmanship!!!
As a Gemologist/Jeweler, I can appreciate how time-condensed these types of videos are. On that note, most people who enjoy viewing these videos have no idea just how long the process actually is. I remember a customer ordering a custom ring from me and wanting it overnight. She just couldn't understand there were other projects ahead of hers and that the process itself takes a long time. I had to keep myself from laughing when she said, "don't you just pour the gold into a machine and the ring comes out?"
That is HILARIOUS! As a crafter that sells handmade product using pyrography, I feel this. I had people ask me why my product was so expensive, and I had to explain to them how long it depends to actually work each piece. Of course they don't understand the art (ex: hardness of the wood determines how easy the burn will be, etc) but it's a "if you know you know" moment. I finally added video to some of my more expensive/popular pieces, so people could see. 😆
I was a custom car builder for several years. A local Jeweler and I used to trade services. The most awesome part of it was learning the intricacies of each other's trade.
@@CTCRZ I admire your craft. I'm sure you'll agree, when you've put a lot of time, effort and skill in executing something like a custom car or custom ring, there's nothing like the dual satisfaction of having done what you've done, but also, the unabashed pleasure the client experiences when they take possession of it.
5:56 I can totally relate to this! I watch a lot of RUclips channels of people that create things (woodworking is my fav), and I just watch it to see you do it. I have no interest in making any of these things myself, and even if I had, my tool collection is basically a hammer and some screwdrivers. This was great to watch and keep up the videos!
I have 10 thumbs, so wouldn’t even consider making anything, but wow! How awesome to watch someone so good and so obviously enjoying what you’re doing. The table is incredible. And love how you’re prepared to share all. Thank you for an awesome video
I'm not a woodworker, but I love the art of it. I love to see the process of something coming together and the hard work and artistic ability to achieve the beautiful end product. It's gorgeous!
I believe the blade stopped and chipped because it felt your hand coming or like you said, the foam had something in it that made the blade feel something coming making it dangerous and worked in your favor, actually. Great video and work. Love your comments throughout the video. Learning a lot. Thanks
I am one of those "just watching cuz". I quilt and build things and refinish/repurpose furniture. I'm 72 and retired but not tired. In my next life I hope to have a shop like yours and express my artistic side like you do. Thanks for the entertainment and beautiful creations.
That is insanely beautiful table. Almost beyond words. And I've learned a ton from your videos. Even got the courage to start doing river style epoxy pours. Not for a large table, just serving trays and such. But I would love to build a full table some day. Thank you for your videos, the commentary, the lessons, the mistakes, the examples, the hiccups, all of it.
Probably one of the most beautiful tables I have seen---You are a master of your craft---You seem to be a very fair and honest man as well---Look forward to future videos
First video I watched from you. I wanted to learn about epoxy and I'm happy I did. Thank you for explaining everything in detail. Amazing beautiful work!
Yes get that CNC - - just so beautifully accurate - and once you've done it once it comes quickly. Tip - practice on foam board to save you breaking bits to start with. A small one that will clamp to your table top will do you fine with a 5cm Z axis - it will just sit on top of whatever piece of wood you're working on and since it's small it'll be cheap. We use ours constantly.
21:47 Looks like it triggered the SawStop right at the moment you touched not only the backing foil, but also the table. This increased the electrical conductivity (decreased electrical resistance), as the table is lower resistance than the foil. The big contact area between foil and table, right next to the sawblade put the resistance down below the trigger value. Just guessing though. Maybe you could test this in test-mode, where it will only blink at you angrily instead of triggering? You‘ll have to watch your fingers yourself though!
@@LFroetschner same here, that stuff is crazy and seemed to make the most sense to me too. I'm not really experienced enough to know for sure considering I didn't even know there was an angry blinking mode to begin with XD
I refinish and restore furniture. I love wood. The grain has a soul IMO. I am in awe at the atristry and brilliant uniqueness of each piece. Thank you for you talent and vision. And for sharing your journey. 👍
I love that you do everything by hand instead of by computer makes everything you do more rare and special! Also, it gives us “hobby woodworkers” hope that one day we could be able to do what you do. Buying an expensive CNC router is simply out of reach for most of us. Keep up your special and wonderful work.
A couple tips when using the forklift on that incline there. Tilt the forks back as much as they can to keep the center of gravity as close to the mast as you can, and keep the load low until you're right at the back of the truck. You want to move as little as possible with the load lifted to avoid tipping and damaging something (or yourself). And those extra 12 feet don't look like much but I've seen too many people go ass over teakettle hitting the brakes that far away and you really don't need to hurt yourself. Also, those extenders will work with your pallet jack. Just saying.
I was thinking the same thing. I would have been right next to the truck before lifting the crate and would only life just enough to get it in. Moving with a lifted load is both dangerous and nerve wracking for the forklift driver.
Wow... what's to hate?
And by the way- that ancient Egyptian PVC pipe was far superior to that junk we have today.
Of all the people mocking my PVC comment, this was the best.
@@BlacktailStudio thank you... I aim to please 😁
Beautiful woodworking, by the way 👍
ok
Ha ha! Egyptians did NOT use pipes of any kind, I don't believe. Did they not use tree trunks?
@@lisamarieashby2523 depends on the era. The great Giza pyramid era, they used riverboats and sleds on the sand, and wetted the sand in front of the sled.
1000 years later, they used rollers, wheels, etc, and whatnot.
Response to your question about 21 minutes in the video. The safety feature of the saw blade stop works off of a voltage differential between the trigger mechanism and a conductive media like a finger. Styrofoam sheets being cut with a rotary blade would be like rubbing a balloon against a flannel shirt. The Styrofoam creates a static charge greater than the blade safety mechanism can handle. A volt differential tripped the circuit.
i noticed this also and his finger touches the deck of the table at the instant it is triggered so i think he discharged himself as he was building up a static charge from the foam as you said
Thanks for the scientific explanation
Thanks for taking the time to share this Lynn!
There's also a relationship in electrical conductivity in foam as it undergoes a phase change due to heat from friction. This can be unpredictable in modern foam products. Not sure if lowering the speed of the saw blade is an option.
Some great responses to this. I was thinking of the static as well. Does anyone thing a wrist worn grounding strap would have helped?
Honestly, if they wanted ZERO reddish tones than they shouldn’t have gone with Walnut. Table looks incredible!
Right? What a pain in the ass thing to request. You don't truley know what your wood is gonna look like until the finish is on and its in your home. He should have let them pick the slab and then quit worrying about it.
Ya not a fan of the end finish but hey I’m not the one buying it. Still looked great but all natural would’ve looked best imo.
Nah there is black walnut that looks incredible and has almost zero red in it. Just was not availability probably at goby
@@nathaniellucas6693 What the customer would be looking for is steamed walnut. I have steamed walnut that is dark chocolate with no sign of red.
I had a client request an Ash and Rosewood end-grain table that looked amazing... and then they wanted me to finish it with Rubio Monocoat Silver. Ugh. We finally came to a compromise we both could live with.
I can't believe I've just spent 25 minutes watching someone make a table, what's more surprising is how interesting it was, great work and fantastic table.
It can sneak up on you
Likewise, watching him work is fascinating.
I enjoyed the video, great quality workmanship. I just don't like the wood finish on the table, it's just a bit boring for 13k 🤷
Snap! I didn't even know epoxy tables were a thing, until now. Fascinating video though. If you like woodworking, worth checking out ruclips.net/user/EpicUpCycling - he makes some fascinating furniture out of old pallets... although the pallet made in this video would probably have him scratching his head! 😂
@@nothingsurprisesmeanymore Everything in my house doesn't come to 13k, you could even add in my car and it still doesn't.
Professional epoxy installer here with over a decade experience. Those small pits that you carved out then re-filled can be completely avoided. Epoxy airates as it cures often causing bubbles (fisheyes) that pop and sink or stay above the surface. An easy and cheap method to prevent that is to use a heat gun at a moderate distance to pop them during the curing process (when it becomes tacky). I have a ton of epoxy tips for you if youre interested. Whether youre using 100 solids, polyeurethane or polyurea.
The “everything is a pain” advice you give in the content is priceless. Such a fantastic outlook. Thank you for putting out the content. Watching you channel is one of my favorite breaks from my day. Keep up the great art.
That’s so true… it comes with the job!
Safety tip (yay): When loading a long crate onto the back of a truck, get as close as possible before raising the forks. That way, if it does start to tip, the truck will take some of the weight and help get the balance back. I used to do this all the time with 1.5 tons of aluminium ingots.
Nice work as always BTW
I’ve used a fork lift to move around coils of wire of similar weight (all metal other than the insulation), and it is definitely a little nerve wracking! I get a bit anxious even watching someone do this in a video.
@Jesus has given you all. Repent or die. stop sending death threats to people
@Jesus has given you all. Repent or die. Jesus blessed ALL my fork truck driving with safety. I was a choir boy and an altar boy. I don’t get people like you who think the rest of us haven’t heard of Jesus or had him bless our fork truck driving! May Yahweh bless you with safe fork truck driving as well!
Was about to say this. I work as a Lumber Department supervisor of a home improvement store and, can't stress this enough, when working with a forklift, always wait until the very last minute to raise the forks :) Good idea passing this tip along to someone who might not know what we know. I regularly lift 3000 lbs bunks of plywood and dimensional lumber daily!
As I understand, the J guy's father was a carpenter? Doubt he had a forklift though...
That has to be one of the most beautiful tables I have seen. The work you put into making it shows that you have a real passion for what you do. I will be watching more of your videos. The people you built that table for clearly didn’t see what all your viewers saw.
Yer, real passion for sure. Oh, that and the fortunes he makes from those over-priced bits of wood.
@@davewallace5008 18months of work is where all the cost is
People are dumb to pay for something they could easily do themselves if they weren’t dumb
@@amsterdamoriginalsaustralia You wouldn't do it if there was no profit in it and a substantial one at that - greed is an ugly thing.
@@davewallace5008 do you have a job?
I'm not a woodworker and I still love this channel, but I don't zone out at all I pay great attention to all the details and store that information in my brain. I don't know what I'll do with it but I enjoy thoroughly.
The county road commission took out a couple of walnuts 3 years ago. I said "No thanks," when they offered to haul the wood away for free and I had a guy with a portable mill come in and slab them for me. The wood has been drying for 3 years and the hygrometer says it's ready to use. This is one of the things I want to do with some of the wood. I've got to go find that step-by-step video of yours. Thanks.
It takes 3 years to dry?!
@@kittykitties4220 Think of it more as seasoning. It takes a long time for the moisture deep inside the wood to evaporate. Moisture is always the enemy of woodworking-- you get rot, loss of adhesion, warping, etc. You need the wood to be the perfect moisture level before you put all that effort into it.
@@kittykitties4220 Drying time is (roughly) proportional to slab thickness, as well as environmental conditions. Where I am, it's about 1 year/inch. The next time you boggle at the price of quality hard wood, think about how long the producer has invested in it.
I think they both look great!! I also agree if they didn’t want any reddish tones they should not have picked walnut. You did a fantabulous job on both.
He made 2 tables? Did I miss something?
Mebbe they wanted "Brazilian Walnut" !
agreed!! Gorgeous!!!
First time I have watched your show. My father was a carpenter but back in the day girls couldn’t even take shop classes. The boys were going to sites and actually learning to build houses. It really frustrated me. Watching this really made me want to embrace my inner woodworker. So I am!!!! I really enjoyed it!
Thats Bad Ass! Get on it Gina!!!
So very true! I remember running through the door when I was in 9th grade with my schedule for the year. “Dad!, Dad!” “I got it!” He replied “What did you get ?” “I shop class!!” “Whoop Whoop 🙌 “. He replied “Good for you “, “I know you’ll teach the teacher to never cut corners and how your work reflects you !”🤭. I was only one of a few girls in his class and remember him telling my dad that he could see the sparkle in my eyes each time I came to class 🤩! Still love wood working today
I felt exactly the same! I wanted to make something with wood and instead was forced to learn how to make oatmeal and tomato soup 🤢
Oh my gosh yes I wanted to go to carpentry school when I was in high school and my dad would not let me because there was only one in the city and they were all boys so I never got to go luckily I found I love power tools
Girls just should not go into construction as a full time job. They legitimately end up looking like dudes. I have 3 daughters, there’s no way in hell I’m letting them get into the trades.
It’s smartest for women to just focus on being sweet and hot and wifely so they can find the best possible man to support them.
I lost my lovely mum 4 days ago. I'm a 65 yr old woman who has zero intention of ever building anything however I love your content & you're helping me thru a pretty awful time Thank you
sorry for your loss
Sorry for your loss
PLEASE ACCEPT . I'VE BEEN WHERE YOU ARE & I GET THROUGH "LOSSES" , BY FOCUSING ON "FUNNY/FUN" TIMES THAT MAKE ME "GiGGLE". MY MOM WAS LIKE MY OLDER SISTER, & SHE RELISHED IN JOKING, NON~ADULT BEHAViOR AT TIMES. : } < MUCH LOVE & LIGHT.
I'm very sorry for your loss. Losing a mother is one of the hardest parts of life, no matter how old you are.
sorry to hear this mate. Thoughts with you and your family.
I happened across this and enjoyed watching you create a gorgeous table! I'm a 72 yr old grandma and it was very interesting. Well done!
Even a real, live Karen can submit a friendly comment without a suggestion. What's wrong with these people!? Good job good Karen 🙂
I also stumbled upon his wonderful video by happy accident. Was a true joy to watch.
71 yo grandma here! 😉
@@RevAim im 111
Styrofoam is electrostatic material. If you pull it over your hair it’ll stand it on its ends. So, that little bit of friction created electromagnetic field which caused the sensor to go off on your saw.
My father-in-law was a Machine shop teacher, and he told me that one time when he was showing me how to pour the foam in different molds he was making. I can't believe I remembered that 55 years later. He was an excellent teacher. R.I.P
Yeah, don't cut foam in a SawStop. Use a reg table saw.
Example- when you ate cutting foam it will shock you in the same way as rubbing socks on carpet and touching someone.
If I had the money, the space, and a family or business large enough to justify such a table then I’d buy that in a heartbeat. It’s beautiful.
13500$ before shipment. I could buy 9 cars similar to my own for that price 😅 sadly a big pass. But yes. It is beautiful 😍
@@AntimatePcCustom You have to be able to afford it to pass on it. Like saying "I'll pass on dating Scarlett Johansson"; honey, it wasn't an option for you 😆
@@krontexpit No thanks.
@@user-nh3gu1ge3d best response 😂
@@user-nh3gu1ge3d That's definitely a new point of view
Great job, I do some woodwork on gun stocks, and a reddish hue is traditional on the finest English doubles and vintage Winchester high grade guns. These are all walnut stocks as well. There is a blend from a manufacture who has perfectly replicated this, from a 125 years ago. Be glad to pass this on, as it would be fantastic color on a large table. Great Vid.
I fall into the category of “People who watch every single of your videos with zero intention of ever building a table.” I love your format, your cadence, your candor and of course, your skill is top tier.
I don't have the space for the tools I do have, and those are just in a small (ish) rolling toolbox. If I get into one of my dream houses in the BC Interior I'll have all the space and projects I could dream of.
ruclips.net/video/hogkKnRYS9g/видео.html
Jesus Christ died for your sins
Same
@@jesuslovesyou2616 Thank you for the best laugh of the day!
Okay…I am absolutely loving both pieces…omg…I wish I was not 73 and had lots of money because I would love to be able to work with wood like you do. Since I know zero about all of what you do, I am just in total awe. If you could do better,I wouldn’t know. Hard, gorgeous work that produces something that stunning is just amazing…thank you for sharing such a craft and skill.
I really appreciate that you included the price of the table. This helps in so many ways and most you tubers don't! Thank you.
Jesus Christ died for your sins
@@jesuslovesyou2616 Well sucks for him.
What was the price?
@@MrGuideElk He said $13,500 18:00
@@MrGuideElk $12k
Shocking to me how much of this work you do all by yourself. My back starts hurting just watching you 😂 beautiful work outstanding video💪🏼
It's absolutely beautiful, for somone that didn't want a red tinge in their table this is perfect for the client.😍👏
OMYGOSH, that table was stunning. I love the look of the “live edge” with the smaller piece squared up with the epoxy …
I am not a wood worker … I do not watch videos like this to fall asleep … I genuinely love watching woodworkers create what I think is art. ❤️❤️❤️
Very grateful for the views! ruclips.net/video/37GCDIC47i4/видео.html
It's very rewarding work
The table & leg fusion is...perfect.
My God man, you are not only talented, you're a full-on artist in the highest degree.
That table is optimistic jazz rhythms & beats, in corporeal form!
I am not a woodworker but I love wood and watching woodworkers bring pieces to life. I completely enjoyed watching and did subscribe. I thought the content was very interesting and the table was beyond beautiful. You are too humble and there are a lot of critics.
As an older-than-70 woodworker, I commend you for your Rock Paper Scissors contest. It warmed my day to see you caring for the next group of woodworkers
I love the frivolous method for picking the lucky person! So much fun. 😁 We need more moments of pure joy in our lives. And your work is awesome!
ruclips.net/video/hogkKnRYS9g/видео.html
And also the fact that, because he got his new one for free, he passed that free-ness on to another woodworker. We have 6 children and I never thought I could afford a floor loom for weaving. A weaving friend GAVE one to me. When it comes time to relinquish it, it will go to another person (for free) who otherwise could never afford one. That way we pass on the joy of our craft.
@@JSCRocketScientist Your wisdom is profound. By taking the attitude of freely received; freely given, the feelings that we have in our hearts cannot be purchased for any amount of money, yet are priceless. BTW, you have me by one child ;) God blessings on you
@@michaelphelan423 Thank you! Blessings on your family too. It’s fascinating to me that the original purpose of a craft guild was to keep secret the techniques in order to protect jobs. Now our weaving guild’s purpose is to SPREAD knowledge of our craft. Which is what is being done here. It delights me.
Loved your life lesson shared, "everything is a pain" and that your wife is the reason your work is so perfect 😄 This is just beautiful craftsmanship, you are incredible ❤️
I love the handmade aspect. It shows a heap more character, and makes the piece more tactile. Your treatment of the edges are an interesting touch, too. Perfection
I watch programs like yours and refinishing programs, because I do not have the physical capability do it myself. I enjoy the artistry, the artwork and the challenge of it. When I was working I taught, and now I write. Thank you for a wonderful video.
Amazing wood working. That is one gorgeous table, and the sister to it is just as gorgeous too. You are an artist of wood working.
Be proud of what you can do and did. A big thumbs up to you.
Your work is first class. If your customers knew more about wood and stain effects it would be better. Sending the examples as you did shows your attention to customer satisfaction. All the things you did for this project tells me you deserve top dollar for your product!
The hand cut bow ties are one of my favourite thing's you do and definitely make me think "I could do that" keep making amazing table thankyou
Better! Your videos are mesmerizing on several levels, first is your obvious passion, second is the stunning art you create, and not least by any means is your superbly crafted dialogue and tone. I found this older video that I somehow missed before and it shows that the outstanding quality of your videos remains superb.
Accidentally stumbled onto this and I am hooked! This was so informative. I am just starting to play around (safely) in my boyfriends unused woodworking garage, to take my love of “crafting with furniture” to the next level. The table is absolutely STUNNING!
I have no woodworking skills or knowledge, nor do I have any interest in learning about it - but I watched this whole video, totally hooked and enjoyed every minute of it.
You're seriously talented at both your craft and making YT videos my man!
... Agree 100% !!!!
.
I want to 2nd. COFFEECAKE’s feelings and thank You for a very enlightening and beautiful video!
same, I don´t even know how I fell upon this
Agree
@@dolarich Fell upon - perfect description. And the table! Wow...
Hey Cam, great stuff as always. Regarding CNC, as you’ve said before, you are always looking for the best product to get the best outcome, and CNC should be no different. If your products are better for using it, there’s your answer.
it depends on how much enjoyment he gets out of handmaking them. if he LOVES doing it that way and only wants a CNC to make stuff quicker, he'll never enjoy the finished product, or the process, as much as he did making them by hand. and vice versa. if he hates how long it takes, he might enjoy one.
Since I started watching your channel, I won't watch any other wood working channel. I love your creations and the videos are fun, informative, and easy to watch!
For the saw stop, I’ve learned from a buddy of mine that even the slightest conductivity will set it off, which if you think about it is great until you use things conduct electricity. The reason the saw stop engaged when you were using the foam Board was because the thin layer of aluminum or whatever metal the foam board has on the top will act like a wire from your finger to the saw blade itself, thus setting it off. Best way to resolve this is to flip the board if you can so then your intact with the foam it’s self but if the material your cutting doesn’t have that then best option to use something like a glove of my preference a piece of wood to push the foam through!
Great videos I’ve learned a lot about wood from them! Thanks a lot! Keep it up!!😁😁
that didn't explain why it was fine on some of the board, it cut half way through the foil side before triggering, witch I will explain by: the foil probably has a coating on it and didn't trigger a conduction until it was rubbed away enough on the wrong spot to make a conduction
@@tomlamb3885 this is correct, it's coated/oxidized and it got an unfortunate high conductivity moment and *boom*
...or static, rub a piece of styrofoam to your hair or clothing and see.
Electronics engineer here. The Viper said it just right, aluminum layer on foam board conducted enough charge from your finger tip to the saw blade and triggered the protection mechanism, sorry...wear gloves next time, a couple of bucks will save a couple of hundreds...Cheers
@@tomlamb3885 every part of machine is grounded, if properly connected to mains voltage, on the part where machine was cutting fine the aluminum part was pushed against the metal parts of the machine and therefore was no conductivity between finger tip and the saw blade, the part where safety was triggered board was standing partially above the metal surface of the machine and therefore was not grounded conducting all the charge from finger to the blade triggering the safety feature...hope this helps...Cheers
Regarding the CNC question, I always use the father of a dear friend of mine, Kazuyoshi Ichiro, as my yardstick. He was a metalworker in Susono, Japan. His family had been blacksmiths and metalworkers for generations, and as proper Japanese artisans they respectfully prioritized tradition and traditional practices. However, they also used modern tools.
Their attitude was that trucks and cars are more effective than carts drawn by horses or donkeys, and understanding the "why" of a tradition is at least as important as the "what" or "how". The traditional approach was to produce the best result possible with the materials, tools and techniques available, and while that led to the development of masterful skills that almost became art forms, the reason was often because of limitations in the available materials, tools or techniques.
As a result, when he worked with the metal, instead of using a set of hammers and an anvil as his grandfather had done, he used a hydraulic press designed for blacksmithing. His philosphy was that the craftsman should put in 100% effort and focus to produce the best result they possibly can, using the best tools they have available.
So using a CNC machine to help would be absolutely no problem, as long as the craftsman is still focussed on producing the best piece they possibly can :-)
Very well put! And make no mistake: getting CNC to actually produce the same quality as artisan work is a an art in itself!! The true advantage of CNC is not the ease of use: its the ability to reproduce without further effort. If you are making one-off shapes, an skilled worker with the right tools may well be able to put out the work quicker and more beautiful
The people that say using a CNC is cheating, or there is no skill involved clearly don't own, or know how to operate a CNC. Just like a hammer and chisel you need to know how to use the CNC correctly to achieve first class results. I built my own large CNC and I would say that is the easy bit. All the associated CAD / CAM programs and how to get the best possible result is an art in itself. While it CAN produce a better result, it isn't automatically guaranteed, you will need to master that tool the same as you do the hammer and chisel.
I'm not a woodworker, but I have been around machines and programs for years. IMHO you should know that you like programming before you invest very much. Look for simulators online or learn coding from someone who has one. If you hate it then keep doing what you're doing.
@@pf2135 yeah that is some pretty sound advice. You will quickly know if it is for you after the first 1,000 hours of using the software...
All my aunts and uncles on my mom's side were/are farmers in NW Wisconsin, and they do business with local Amish all the time, including having them make dining tables. These Amish use no power tools at all, and deliver all furniture with x2 horsepower buggies. They have no problem with you driving your pickup truck into their driveway, though, if you need to pick something up. They have very nice looking houses with no electricity or indoor plumbing.
My mom didn't want to marry a farmer, so she moved to the "big city" before I was born and never moved back. They call me city slicker when I visit.
I loved the colour of the finished table - but if it was my table, I would have liked it a bit 'redder'! I really like how you preserved the irregularities of the origional slab but managed to make it smooth enough to use and clean easily. The chamfered edge on the table helped 'tame' the 'crazy raw wood look' just enough to make it civilized! The table base was great and suited the slab while it made the table 'leg and knee' friendly. Great work!
So entertaining I can’t stop watching. Not a future carpenter but amazed at the skill and beauty of final products. Simply fantastic.
You made this all look a LOT easier than it truly is. My husband is a woodworker and I see what he goes thru. Beautiful table, we'd be honored to be the owners of a piece of artwork like that.
Artwork? It’s natural, he did nothing special
Jordan quattro if he did nothing let's see your work I'm a woodworker and there is more then meets thee eye so save your shaming comment
@@jordanquattro7856 dude propably work minimum wage and don't own a single tool
@@jordanquattro7856 is right. Tables grow on trees.
@@fabrizio3672 😂 I’m not taking anyones shit anymore. Do not be fooled. Tables Grow on Trees.
This guy is amazing. You can see the amount of effort he puts in to every little thing. And how he’s always thinking ab other people, great guy great channel
"I was literally addressing you specifically". That's them told. Such a fabulous table and that base is just something else. Breathtaking. Well done to it's maker too.
That comment is absolute gold.
Hola
soy Anna
y te escribo desde España.
No podia dormir y cayó en mis manos uno de tus videos.
Yo no tengo ni idea de carpinteria,
pero soy una persona curiosa y me gusta aprender y estar informada.
Tu video es super interesante.
Lo explicas todo con una sencillez y claridad,
que da gusto seguir viendolos.
Y que decir de tu maravilloso trabajo.
Me encantan tus mesas.
Son realmente preciosas.
Te felicito.
Las patas que sueles usar,
son muy bonitas.
Llevo mucho tiempo
mirando revistas de decoracion,
y en ellas encuentro patas asi o parecidas.
Las que utilizaste de acero inox.
son fantasticas.
Seguire viendo tus videos,
pues a parte de pasar unos minutos muy agradables
e aprendido muchas cosas con ellos.
Gracias
y nuevamente Felicidades por tu trabajo.
Un saludo.
Better or worse, If the client loves, that’s all that really matters. I’m a fan of the reddish hues myself.
Seeing your pros & cons with CNC vs hand cut bowties would be interesting, the occasional CNC flattening would be good to see as well.
All the best Cam.
Loved the video. One suggestion I would give, is to make your work table with the ability to raise the height to help save your back during some of your processes. You could probably have your friend the welder create the table and you can use a pneumatic system.
You can also build a winch system like they use for boats to move those massive, heavy slabs from your truck to your work table. Many years ago my dad and I replaced an engine in my car and he built a very simple winch that was attached to wood beam He set on the two walls on each side of the garage. We were then able to move the motor exactly where we wanted it.
I was lucky to grow up with a genius engineer for a dad. He knew how to solve pretty much any engineering task.
We need to get this comment to the top of the list to make sure he sees it -- good suggestions!
Good idea, but I would use a hydraulic lift system seems it would be more reliable when lifting heaver items. Pneumatic or hydraulic either is better than using your back, LOL
Tip: In order to eliminate bubbles / imperfections after filling the epoxy, try vibrating the whole frame. Could be an impact drill on a piece of timber, or maybe a Food Processor / blender fixed to a board on top of the table for ½ hour 👍
I wonder if anyone has repurposed a bass transducer for this very job.
You do this for cake batter too, when you put the batter in the cooking pan, you bring it up about an inch and drop it. Works great, and you can always see the bubbles coming out.
Vacuum chambers work great for this, though it might be a little hard to find one big enough for that table :P
He could use one of those new massage guns that are everywhere now and can be gotten for cheap. He would likely need to go around the edges of the table with it though to make sure every area gets vibrated
I don't know how I became side tracked by this video, but I'm glad I did. I couldn't stop watching it. It was so interesting to see all the steps and hard work put into such a beautiful table. Your attention to detail is amazing, and I love that your wife helps you. You should really be proud of your fine work. I admire your skills.
Same for me, Melissa. I know someone from Houston that has a table like this, and I guess that's what drew me in. Couldn't stop watching. Not a woodworker, or particularly handy, but I really enjoyed this video.
Regarding the CNC question: have you ever considered a Shaper Origin? That seems like the obvious solution to work on your large slabs, because you are not confined by the size of any machine bed. Also, they take next to no effort to "program". You load an SVG of the shape you want to cut, which you can create e.g. in Inkscape. You may have to play with the tolerances a bit to reliably achieve a "fits the first time" experience, and you have to knock out the corners yourself still. But it may speed up your process significantly.
nice try shaper origin
That was my first thought especially for what he is doing with the bowties. It's not cheap but for someone doing this high end work, it might save time and therefore money. ruclips.net/video/hMgFFlDhTbA/видео.html
I have a Shaper Origin. It is amazing for bowties. Perfect.
Yeah that would actually make sense for the bow ties. But don't worry mate, people hate on it the same way they do on cnc
If you round the corners it will save you a step.
"I was literally addressing you specifically!" Might be the greatest reply ever!!! Thanks for another great video!! Also thanks for making all of this work seem easy. It's the people like you that make a very very difficult thing seem easy that get people like me to try doing it and then me realizing that even with my knowledge and experience it's still a very very hard trade to do! Thanks for making me challenge myself!!
I vote for continuing to do bow-ties by hand. It’s time consuming, but it’s also cool that they look so perfect and are done by hand.
They'd be MORE perfect with a CNC, you can cut to withing .0001 inch np with a CNC
@@dannymaiorani519 As a CNC machinist my self? Not with those aluminum extrusion table routers. Not even Tormach can do that and maintain a .001 repeatability tolerance. Some HAAS budget machines are just as bad. That said if you have seen a CNC do a job once you have seen it do it 10,000 times. Hand made products should stay as hand made as the person making them wants them to be.
@@Matt_RangerExactly. I would much rather see 60 seconds of handcrafting than 10 seconds of automation.
@@viperstarpoint9 yeah I wasn't really suggesting that I was suggesting like a mill. When I had my German auto shop I bought a tree 310 from Berkeley University that they thought didn't work and I got it running and I used that.
The rest of it is still hand built I've seen those bow ties sort of loosen up over time I don't know if his do. So the mill could be an improvement possibly in that regard.
Loved both colors! My husband and I have done a lot of remodeling in our home. One room at a time = no loans! Paid in full with cash on hand as we could afford each room. Thirty years of construction is enough! Almost done and I’m ready to move to a finished house, sit back and enjoy it❤❤❤!
Doing the Hand made bowtie, and fixing every little imperfection " thanks Mrs,Wife" is what gets you the Highend price. Never let go on quality work.
man i love wood, just imagine nobody would ever had seen THAT particular slice, that grain pattern, hidden for decades, better than discovering a gemstone, and now revealed for people to admire like a famous painting. Bravo
Very bittersweet.
I absolutely love that you are so real and are willing to show the reality of woodworking instead of cutting to make you look "perfect". That's such a disservice to folks who really want to know what's what, what to expect, and to be able to correct for mistakes you've already made. Most folks adjust and edit to make things look like they got it right the first time, and that's a shame. NO education happens.
Looks beautiful. Always move the product as close to the truck as you can before lifting it. If it does tip forward it won’t crash to the ground. You are incredibly talented and it shows in everything you do.
I absolutely love to see and watch hand-customized creations of any kind. Your explanations throughout is very satisfying. I am not a work worker by any means and I can understand most of what you are saying. What I love the most is your attention to detail. I could watch you create masterpieces all day. In addition, you are physically strong to do what you do. It takes strength to handle such large and heavy projects. I love your wife's OCD too. Her eye for fine detail is what puts the kiss of perfection on your work. I can tell she loves you because she cares enough for you, your name, and your work that she helps you to put out the best product possible. You're a great team. Thank you for sharing your artistry and skill with us.
Very sweet ... I agree ♡
That round slab at the beginning of the video is INSANE I can't wait to see what you do with it 😍
Yeah I loved that slab too.
that slab is amazing, it has so much character. can't wait to see what it becomes
Won’t that make one heck of a pretty table. Shoot, that’s something your kids and grandkids and their kids would fight to get!
The darker table is to die for, stunning. Beautiful work. Love the base too.
A wood slab is not worth death of human life, you fool
@@GardenGuy1942 I bet you're fun at parties.
@@GardenGuy1942 Depends on how nice of a slab it is to be honest
🤭
The final color - as shipped - is superb.
Somehow this video just dropped into my feed so I watched it and all I can say is...you are a fastidious craftsman and your work is amazing! I’ve never seen a slab table made from start to finish, but it’s just incredible to know what goes into it! That was a gorgeous piece and I hope the client knows what it took to create that stunning work of art!
Same happened to me and enjoyed every minute!!! Gorgeous 🤩🤩🤩
A fascinating 25 minutes that covers thousands. Having seen the start it would be wonderful, and complete the circle, to see it installed. Thank you for sharing your skills and time making the video.
Same here!!
Same
Both of the tables were absolutely gorgeous! I would be proud to have either one in my home!
Absolutely gorgeous!!!! I wish I could do things like this. When I was a little girl, I fell in love with the smell of wood as my Dad did a lot of woodworking. I inherited his carving tools and my brothers got the larger tools. Just one more thing on my endless bucket list!!
That custom table came out absolutely gorgeous! I'm not a wood maker but totally love watching. Glad I fell upon your channel. Much respect!
Same!
The foam probably picked up enough static that a slight increase in speed, while you pushed it through the blade, released that static and set off the stop
I wonder if that thin film of aluminium or whatever it is, "helped".
Absolutly caused by alu foil
You took the thought right out of my head
If there is ever any question about conductivity I always use the bypass key/function. It eliminates the safety of the SawStop but won’t trigger the stop mechanism.
I was going to leave this as my guess, static build up and it sensed the change when the positive build up on the foam grounded.
I have been going through a really tough time the past couple weeks. Unfortunately I have had a lot of time on my hands. Somehow, the universe has led me to your channel and I can’t tell you how much I love it. Whenever I feel like the world is coming down on me, I watch one of your videos. I love wood working and I have learned so much from you. So from the bottom of my heart, thank you. You’re an artist and absolutely love your work.
You are not alone.
I feel like in the past, people like you and i, in rough times, might go down to the local village blacksmith and carpenter to just look at them work for a while.
How lucky we are.
I’m a firm believer that there is always room to improve on anything in life, but this channel is perfect. The voiceover is awesome, work is incredible. I love this channel.
He has the perfect blend of dry humor and sarcasm!
@@mushudragonusa2014 and he speaks at a normal volume, no yelling or silly inflections in his voice.
I am absolutely impressed, hands down the best channel of this topic.
If I could afford a table like that I would so order one. I love the grain and the color. When he put that black on there I was like "whoa, I don't know about this". But it turned out so gorgeous! Watching this video just goes to show that there's a tremendous amount of work that goes into constructing hand made products like this. I would love to have a handmade table but I would have a live edge on it if possible. I have wood throughout my house and love the warmth that it brings to a home. The people that bought this table will hopefully watch this video so they know how much care and love went into the table they bought. Just beautiful!!!!
I've been binging your videos
lately and I just have to say, it's a pure joy to see your work and what you create!
I feel the same. He is quite talented isn’t he, I just wished I could afford something from him.
Thanks bud!
when i was a kid, i used to help my grandfather in his shop but he didn't have all your tools and i would love to use them now. Greetings from Italy
New here 😇😇😇😇🙏🙏🙏🙏
ruclips.net/video/hogkKnRYS9g/видео.html
"Better or worse" I just want to say thank you! I initially came here to just relax and see amazing content but I do woodworking as a hobby and I learned a ton form you. I learned how to prevent warping of the wood, gumming up of the sand paper, dealing with cracks and bubbles so basically all the problems i faced and was unable to solve when building my desk. I think it is great how you drop this information casually on the side! Concerning the bowties, I personally prefer watching you make them by hand as it is first very calming to watch someone do precision work and second it would be the only way I could do it.
Ps: I love the style of your work very inspiring
I appreciate this videos contrast to the "It's so easy, it works everytime" approach to some of these craft channels. Knowing things go bumpy builds confidence in the entry of learning.
I have never watched a table being built, but this was a very interesting. I just fell into it, but I love the process. I want to be a builder. I’m an artist. It’s a form of building that I love the process and I love your devotion to perfection, thank you for being willing to share the whole story. I actually love the whole story.
Love the way the base brings a modern look to the design and highlights the black inlays.Awesome table!
I'm impressed that you are able to admit your faults. So many artists avoid the truth that we have flaws and yet they still exist. Lol your work is exceptional and congratulations on such a good informational video.
*Suggestion: You don't show that you have marked the artwork with a signature, date, stamp, number or anything that accredited it to you. Please show how you prefer to signature your art, so I can identify your art pieces when shopping in the future. Eventually someone will sell or auction them off, or donate them from estates. I would love to be able to identify your "Marks"!💗💯✔
*Question: Have you followed up on the wear/care of this table?
A "Where is it now!" kinda video would be fun to see.
*Looking forward to more from you!
Thanks for sharing- "Rock Bottom" in Ohio!
Defintely agree on the signing it! I love having any artist signature on their work when I buy it. Adds something special.
"Everything we do is a pain"- absolutely love this. I dont do woodworking or anything, but i like seeing how you guys do this stuff and the process. I am a 3D artist, and i can see the similarities between 3D art and woodworking. Obviously, two completely different crafts , but still run into problems every project. Every project is a puzzle, and that's a part of the appeal i suppose. Solving small (sometimes large) problems.
I do woodworking and I can't see any similarities. No hate but I feel like tablet "painting" and 3d printing has destroyed the craftsmanship and art of actually creating something with your hands. I can't imagine it feels nearly as satisfying when finished. Maybe I'm wrong, don't mind if there's some schooling you can take me to to change my mind?
@@heatherlee7123 There are definitely similarities to these two crafts. Besides op said 3D artist, not 3D printing, which is very different. I can say both have the same amount of satisfaction when the job is finished. It really depends on the time spent on it and what you feel about your finished work yourself. Not trying to be condescending or anything, just speaking my mind from my experience!
@@heatherlee7123 3D art is very different from 3D printing.
i am an e.r. nurse, i think i could apply this motto a lot in my in my daily (well technically nightly) life too!
I love watching your videos. I'm the worst at anything and don't have a clue about what you're making. But I totally enjoy watching your videos because I learn things and it relaxes me.
It amazes me that you can see what you're going to make before you start 😊.
Thanks for sharing, goodbye for now.
It's lovely seeing you work. My father (who died when I was 16) worked in a foundry smelting bronze, but was also a woodworker. it was incredible as a kid watching his turn scrap wood into beautiful items that he'd sell. Watching you reminds me a lot of him, but he didn't have so much hardware because it was thirty years ago and he didn't have access to such machines. Thanks for the channel. Subbed.
Man, that's incredible! I have so much respect for guys like your dad! These guys could make stuff that they needed and took pride in what they do! I am no where near the expertise of this gentleman or your dad, but I love woodworking and building things that I want! I learn so much from these videos and people like you who share their experiences or memories! Just a humble "thank you", brother!
I think we had a friend who used the same colour on a table for his gazebo. When he first applied it he was sooo disappointed, but as he let it weather it mellowed and brightened and in the end, the table is gorgeous. I love it.
If I were in a position to have a table like that made I would honestly be quite happy with it. On the other side of the coin..... if some one can afford a $13500 table for their "dream" house they must be pretty well off so im not surprised if they actually hated the table. You still provided a table thats more than worth what you sold it for.
God bless you dear! I am a zoner and so enjoy your videos! Please don't stop for all us zoners out there you are a Godsend to watch to bring such beauty from His and your creation😊😊😊😊
Honestly one of the best tables I’ve seen! Love the color and the wood grain!, this video was in my recommendations and I don’t regret clicking on the video! Absolutely love your whole process and set up! You’ve earned a sub from me! Keep up the great work! Excellent craftsmanship!!!
As a Gemologist/Jeweler, I can appreciate how time-condensed these types of videos are. On that note, most people who enjoy viewing these videos have no idea just how long the process actually is. I remember a customer ordering a custom ring from me and wanting it overnight. She just couldn't understand there were other projects ahead of hers and that the process itself takes a long time. I had to keep myself from laughing when she said, "don't you just pour the gold into a machine and the ring comes out?"
That is HILARIOUS! As a crafter that sells handmade product using pyrography, I feel this. I had people ask me why my product was so expensive, and I had to explain to them how long it depends to actually work each piece. Of course they don't understand the art (ex: hardness of the wood determines how easy the burn will be, etc) but it's a "if you know you know" moment. I finally added video to some of my more expensive/popular pieces, so people could see. 😆
😅
I was a custom car builder for several years. A local Jeweler and I used to trade services. The most awesome part of it was learning the intricacies of each other's trade.
@@CTCRZ I admire your craft. I'm sure you'll agree, when you've put a lot of time, effort and skill in executing something like a custom car or custom ring, there's nothing like the dual satisfaction of having done what you've done, but also, the unabashed pleasure the client experiences when they take possession of it.
I personally love the red tones but think you did an amazing job implementing a solution to cover them. SO much work went into this.
I couldn't STOP watching! Highest skill and artistry - a stunning table BRAVO; ultimate craftsman that you are
5:56 I can totally relate to this! I watch a lot of RUclips channels of people that create things (woodworking is my fav), and I just watch it to see you do it. I have no interest in making any of these things myself, and even if I had, my tool collection is basically a hammer and some screwdrivers. This was great to watch and keep up the videos!
I have 10 thumbs, so wouldn’t even consider making anything, but wow! How awesome to watch someone so good and so obviously enjoying what you’re doing. The table is incredible. And love how you’re prepared to share all. Thank you for an awesome video
10 Thumbs? Put them all up for Blacktail!
I'm not a woodworker, but I love the art of it. I love to see the process of something coming together and the hard work and artistic ability to achieve the beautiful end product. It's gorgeous!
I believe the blade stopped and chipped because it felt your hand coming or like you said, the foam had something in it that made the blade feel something coming making it dangerous and worked in your favor, actually. Great video and work. Love your comments throughout the video. Learning a lot. Thanks
I am one of those "just watching cuz". I quilt and build things and refinish/repurpose furniture. I'm 72 and retired but not tired. In my next life I hope to have a shop like yours and express my artistic side like you do. Thanks for the entertainment and beautiful creations.
That is insanely beautiful table. Almost beyond words. And I've learned a ton from your videos. Even got the courage to start doing river style epoxy pours. Not for a large table, just serving trays and such. But I would love to build a full table some day. Thank you for your videos, the commentary, the lessons, the mistakes, the examples, the hiccups, all of it.
That i think is a proper way to do it.. start with something small and work your way up..
same mistakes can happen no matter what size material
Probably one of the most beautiful tables I have seen---You are a master of your craft---You seem to be a very fair and honest man as well---Look forward to future videos
The Tree where it came from must be magnificent.
First video I watched from you. I wanted to learn about epoxy and I'm happy I did. Thank you for explaining everything in detail. Amazing beautiful work!
How could you not love this guy! He does all this in the best Interest for us and most importantly him. Gotta love his work ethic
Yes get that CNC - - just so beautifully accurate - and once you've done it once it comes quickly. Tip - practice on foam board to save you breaking bits to start with.
A small one that will clamp to your table top will do you fine with a 5cm Z axis - it will just sit on top of whatever piece of wood you're working on and since it's small it'll be cheap.
We use ours constantly.
ruclips.net/video/hogkKnRYS9g/видео.html
21:47 Looks like it triggered the SawStop right at the moment you touched not only the backing foil, but also the table. This increased the electrical conductivity (decreased electrical resistance), as the table is lower resistance than the foil. The big contact area between foil and table, right next to the sawblade put the resistance down below the trigger value. Just guessing though.
Maybe you could test this in test-mode, where it will only blink at you angrily instead of triggering? You‘ll have to watch your fingers yourself though!
I think you’re probably on the right track. The device tracks conductivity. My initial thought was the static charge caused by the foam board.
@@LFroetschner same here, that stuff is crazy and seemed to make the most sense to me too. I'm not really experienced enough to know for sure considering I didn't even know there was an angry blinking mode to begin with XD
I refinish and restore furniture. I love wood. The grain has a soul IMO. I am in awe at the atristry and brilliant uniqueness of each piece. Thank you for you talent and vision. And for sharing your journey. 👍
I love that you do everything by hand instead of by computer makes everything you do more rare and special! Also, it gives us “hobby woodworkers” hope that one day we could be able to do what you do. Buying an expensive CNC router is simply out of reach for most of us. Keep up your special and wonderful work.
I love everything about this channel - he shows all the process as it is without any sugarcoat 👍
A couple tips when using the forklift on that incline there. Tilt the forks back as much as they can to keep the center of gravity as close to the mast as you can, and keep the load low until you're right at the back of the truck. You want to move as little as possible with the load lifted to avoid tipping and damaging something (or yourself). And those extra 12 feet don't look like much but I've seen too many people go ass over teakettle hitting the brakes that far away and you really don't need to hurt yourself.
Also, those extenders will work with your pallet jack. Just saying.
Jesus Christ died for your sins
You should also try to approach in an uphill direction wherever possible !
Imagine believing in gravity
I was thinking the same thing. I would have been right next to the truck before lifting the crate and would only life just enough to get it in. Moving with a lifted load is both dangerous and nerve wracking for the forklift driver.