Autodesk inventor Tutorial for beginners Exercise 2
HTML-код
- Опубликовано: 1 июн 2018
- in this tutorial video we will create a 3D model in Autodesk Inventor 2017 with the help of Sketch And 3D tools and learn about Sketch, Extrude and Cut commands.
1)Autodesk inventor Tutorial for beginners Exercise 1
• Autodesk inventor Tuto...
2)Autodesk inventor Tutorial for beginners Exercise 2
• Autodesk inventor Tuto...
3)Autodesk inventor Tutorial for beginners Exercise 3
• Autodesk inventor Tuto...
4)Autodesk inventor Tutorial for beginners Exercise 4
• Autodesk inventor Tuto...
5)Autodesk inventor Tutorial Design of Fidget Spinner
• Autodesk inventor Tuto...
6)Autodesk inventor Tutorial Emboss and engrave
• Autodesk inventor Tuto...
7)Autodesk inventor Tutorial How to make 3D Pipe
• Autodesk inventor Tuto...
like Facebook page.
/ cadcamtutorial
Subscribe our RUclips Channel.
/ cadcamtutorial
I have inventor installed in my computer for a long time i was never able to do anything until i saw your video.. thank you so much
You are a great teacher! You are concise and purely informative. Everything you say has an application. Keep up the great work you do for learners all over the world.
You are the best! Tanks for explaining so well!
Great job. In the first sketch, the distance should be 90 mm in order to maintain 75 mm between the centre points, and also the 35 mm is from the cone centre point
what i like to do with these videos is watch how its done and try remember as much as i can to recreate it with the picture. Its been really good for learning thankyou
Vimal ojha has best content related
I keep on loving your tutorials
thank you very much for sharing this tutorial
More Inventor !!! Thanks
Sir, I am really a great fan of your tutorials, please make some videos on analysis of structure on inventor
These videos are so helpful thank you so much
3:50 my lines will not automatically convert into circles. Doesn't matter how many times I follow your instructions.
after drawing a line hold left click so it curles
This is great, thank you!
great video, thanks
2:34 you don't need to resketch that circle, all you need is left click the arrow of exstrusion1 and then right click sketch and pick visible to show your drawing from before extrusion.
could you please upload a brief video about it.. thanks
Thanks!
Good Afternoon Sir. Thanks 4 sharing this knowledge with us, it has been very useful to me. I wander if you could share with us your sketchbook, what you use as a guide to build the models on this videos? Thanks in advance and Best Regards.
For 2:30 sir you can open the extrusion1 and right click on sketch1 then you can open visibility so you do not have to draw the same circle for an other extrusion :)
Great stuff!
An excellent channel too much the CAD CAM TUTORIAL. One thing I would like to see in the channel would be a tutorial of a CNC machine. I'm fascinated by these machines! Stay here my suggestion for a future project for the channel.
Thanks for everything :)
should post nc file and run in 3D
Perdona mi ignorancia, pero de centro a centro de los dos vaciados no es de 35mm??
Forgive my ignorance, but from center to center of the two castings is not 35mm ??
Thankyou Sir, btw I am a beginner
Who is this guy.... Such a great tutorial
buen video y explica muy bien , pura vida
Thank u so much.. it is very useful..
Did the exercise again, GOT IT!!! Thanks CAD CAM!
Thank you so much for sharing with us. If only you could come through the screen and help me with my struggles. At14:25, when trying to create the rib, I get a message "Sketch constraint already exists."
Hi. Great work. Well... After extrusion 1 there is no need to draw a new circle for extrusion 2. just visible sketch 1 and extrude again. Thanks
You are the best !😁
Thank you so much man
thank for this useful video
please make a playlist of full tutorial for autodesk inventor
Good tutorials .
For autocad users , transition to learn inventor is little difficult, all the time conversant with move copy erase simple commands in autocad , here in inventor things are so very different.may be with lot of practice ,things may settle to know and un derstand properly
Nice to be confident with the software
Does the rib fill up the gap in between cylinders?
Excelente video tutorial
great teahcer!
Thank you!
2:30 You don't need to draw the circle again. Just share the previous sketch and reuse it for the second extrusion
Nice and Thank You
Thank you for you'r helping
I am really enjoying Inventor thanks to your videos... I was wondering, is there a way to add titleblocks to these? I haven't figured that part out... even Solidworks, would drive me up a wall.
which plane is perfect for drawing how to identify
Hi Sir, I want to make curtains for my car doors, I have made a 3D scan of the car door but I don't know how to import it into Inventor and make measurements, is it possible to do a tutorial on how to import 3D scanned data and measure the dimensions, thanks
如果我有其他的操作步驟要提供給CAD CAM TUTORIAL 該如何做
What if I have other steps to provide to CAD CAM TUTORIAL
Спасибо за урок
Thank you
Thank you 👍🙏
What is the basic step for drawing the 3d model
nice thank you
Good job
gd mrng sir,
please suggest me a tool through which I can make 3D
pipeline with pumps and water tanks,
I hope you got my point.
ClearEdge EdgeWise 3D
You know you can just make the sketch visible again and then extrude your circle right?
thank you sir :)
how do you select the side of the extruded circle. mine passes thru when i sketch it at 8:01
hi trying to copy your video every time I draw lines from circle at the beginning. when I enter in 35mm the circle moves from CenterPoint how can I stop this from happening thanks Dan
Hi! There is an incorrect dimension at 8:16. The width of the rectangle according to the drawing is not 35 mm, but 12,5 mm. I just thought I share my remark to this. Keep up the good work, I like your channel.
Norbert Osztermajer Thanks i will correct it here.
There is also a similar mistake at 1:37. The length is 75 plus 15 mm. 75 only reaches to the center point of the cut extrusion
and also another mistake: the bridge between the cilinder and half cilinder is not a parallelepiped, but a trapezoid.
The linkes are not horizontal as in 3:40
That is the radius of the circle not the width of the rectangle. Look closely
From the top view, the part which connects the cylinder and magnet looking part should look like a downward pyramid instead u drew it in a rectangle shape which I think should be wrong.
From the blueprint u can actually see that the side of this component is not parallel to the rib.
CAD CAM TUTORIAL Hi, where can I find the tutorial sketches?
Very thick accent but good video
Thicc
I am using inventor 2020 for the 1st time, trying to learn, but when drawing a line then holding the left mouse key to create the circle my center point wants to stay on the last line I was on. Not sure what I am doing wrong if you have any suggestions that would be great. I have to learn this in a week for a job interview.
I had the same problem. When you draw your line, then go back to get the end of the line again to start your arc, drag your mouse like you're drawing the arc itself. Don't drag our mouse straight down or across, drag your mouse like your drawing the arc or circle.
it was a little fast paced and when you tried to apply the coincident constraint, you said concentric
great video series; however, the blueprint and the drawn figure won't match. You forgot something, you took that connecting part as a rectangle but actually it is not
is there any buttion same Entities button in solidworks?
nice
cool video
Can you please upload the Drawing file also in Google drive and add link ?
Thank you
check my FB page CAD CAM Tutorial you will get 2D file.
CAD CAM TUTORIAL thanks sir
The rib is not as per 2d isometric dwg. There is no straight part at connection of top and bottom circular part.
good chanel
While it was helpful to learn a few new commands, it is a shame that your model does *NOT* match the drawing accurately... The 75mm for the forward fork length is measured from the center of the main cylinder axis to the center of the fork radius... thus your model is too short in the forks. Then the back "clamping" section is 35mm from the center of the main cylinder to the centerline of the 'X' axis through hole (or the tangent of the outer arc endpoint)... I corrected those errors and my model now matches the actual drawing whereas yours is essentially a "scrap" part, until you adjust your dimensions properly....
glorius, i was wondering why it didnt make sense, i thought I was doing something wrong.
Hello i have a question,
What is the name of this software?
13:20 you don't need a sketch, you could just extrude the whole plane
Sir here mid circle having tangent line
I WANT THAT OBJECT DRAWING IN SOLID WORKS PLEASE SHARE ME IF YOU HAVE
buy a machine drawing text book. Lots of models are there.. Including this
Your design incorrect dimension, first the 75 mm false, is true a 90 mm. Second the 57.5 mm false, is true a 35 mm in center circle...
Yes u r right... Vimal ojha have best content on this
concentration on command, not design
where i can find solidwork demo or 15/30 days of test? someone can link me?
sir that tab on left at 2:21 , how to turn it on
when i want to do the last part 'rib, i can draw and connect the line; but when i go for 'rib' the lines are not turning blue and the rib function does not work or preview.
COMO CAMBIA DE UNA LINEA A UN ARCO EN UNA MISMA OPCION ???
Why are you clicking 3 different edges at 4:56?
hey bro
Wonderful tutoriål but regret to mentiøn, couldn't hear a single word. Could speak loudly:
8:16 Dimension 35mm is the distance between center to center of circles. You measured wrongly!
i am not able to make the semi circle by left clicking
4:38 you did something cause mine say it will overconstraint the scetch so it doesnt work
the gap has problem inventor coming out error (Project Face Loops: problems encountered while executing this command.
Sketch16: Problems occurred while building this Sketch Projected loops merged in to duplicates)
usted puso muchos avisos
This one was a bit harder to understand.
i think horizontal dimension 35 for rectangle is wrong, since 35 is dimension given from center of the circle, not the edge of it 9:31
i think so. it's wrong
Indeed.
Hi
Timestamps of car honks:
0:25
Dear Sir,
Thanks for your video..
While creating the rib, I have face problem is called point dragging.. I am unable to drag my point after the constraint process.
Pls suggest me solution..
35° :) 45°
More solidworks
i tried to recreate this desain, but i got struggle when you said, click left mouse key to convert line to circle, my autodesk inventor cant do that, fyi i have 2024 autodesk inventor, can anyone tell me what is wrong?
You have to hold down the left mouse button and drag the line.
Can u please provide the file of inventor with license. That would be great
Your 35mm is not correct, it is from circle center to circle center. (at 8:24). and there are more mistakes.
My guy I think you made many mistakes here. It's 75mm to the center of the smaller circle. And the 10mm thick block you made is tapered as in it goes from the center of the big circle to the center odd the smaller circle. I'm not to sure how to explain this to you with words but can prob show you once I complete the drawing.
TERA BANDIT QUEEN GROUP'S
VERY SOLID FORM TAKE PLACE
KARTA HAI.
What a unintuitive, structureless and cumbersome way to create such a part. And the accent grinds my gears too.
There may be some errors. There are dimensions at 8:16. You can calculate this. If you don't like it..
You are not making the model as it are in the drawing...