working logic; The evaporation of the aluminum in the cloth goes to the area of the balloon in the place of the insulated airless environment, inflates it and pushes the balloon arm up. Afterwards, the cold water empties the air inside the balloon again, so it descends and cycles. Of course he pushes in the syringe.😊
stirling motors runs based on difference of preasure from outside and inside, i guess the aluminium cloth is just to allow the flow of air at less speed, it moves the air from the hot part (candle) to the cold part (water)... it is a bit complex to be explained in a yt comment so jsut google it or search a 10 min video
A Stirling engine works based off of the expansion and contraction of the working fluid (air) as it is cooled and heated. So, the candle heats up the air, which pushes the piston up to the cold water, which cools down the air, and expands the balloon, which elastically pushes the piston back down, restarting the cycle. Stirling Engines have no evaporation, and in order to work must actually retain their working fluid within the system, as opposed to a steam engine which releases it to push the piston.
well I have all the things I need to make this, I have the cans, the steel wool, the bicycle spoke, the 3d printer and so on. One question Where do you get that sheet with the gritty sounding stuff on it? At 00:14?
@@armanda-s1776bonjour avez vous trouver les fichiers si non vous l'avez peut être modéliser vous même si c'est le cas pourrai-je avoir les STL via un lien mega Merci d'avance
Non, cela ne peut pas fonctionner sans eau car l'eau refroidit l'air chauffé (différentes choses se produisent pour refroidir l'air). Cela fonctionne si la bougie fournit suffisamment de chaleur (écrit en utilisant la traduction, désolé pour les erreurs)@@johnpages4627
Bloody hell, that is truly wonderful. Something so simple and I was smiling like a kid watching magic all the way through 😄😊 Thanks for the build. You know if you were to have a Fresnel Lens focussing on water at the base, instead of a paraffin lamp as the heat source, would that work?
I like the videos but in both you skip what the piece that is around the wire between the lower can and upper that keeps the steam in. The steam on the one I built keeps coming out of there,
No, the purpose of the Gamma Type Stirling engine is to pass the hot air into the cold air intake. So your piston MUST go from the very top (to let the air pass through the chamber) and then go down (to let the hot air create pressure in order to lift it up)
Zafer abi sana sorum olacak ama eski videodan abi çanak anten ile internet tüm yerde geçerlimi? Bide aylık kaç ödüyoruz internete? Cevaplarsan sevinirim
Foarte bun videoclipul, grozav lucru!
Hep böyle samimi ve gerçekten halkın adamı olarak kalmanız dileğiyle güzel video ellerinize sağlık
working logic; The evaporation of the aluminum in the cloth goes to the area of the balloon in the place of the insulated airless environment, inflates it and pushes the balloon arm up. Afterwards, the cold water empties the air inside the balloon again, so it descends and cycles.
Of course he pushes in the syringe.😊
uh, no
stirling motors runs based on difference of preasure from outside and inside, i guess the aluminium cloth is just to allow the flow of air at less speed, it moves the air from the hot part (candle) to the cold part (water)... it is a bit complex to be explained in a yt comment so jsut google it or search a 10 min video
@@pablerichi Same thing as I said. Also not necessary. This engine is useless after all.
A Stirling engine works based off of the expansion and contraction of the working fluid (air) as it is cooled and heated.
So, the candle heats up the air, which pushes the piston up to the cold water, which cools down the air, and expands the balloon, which elastically pushes the piston back down, restarting the cycle.
Stirling Engines have no evaporation, and in order to work must actually retain their working fluid within the system, as opposed to a steam engine which releases it to push the piston.
@@Spoon80085 I'll read it later, I have something else to do right now.
TEWRIMA KASIH ATAS INSPIRASINYA YANG SANGAT BERMANFAAT CARA YANG PALING EFEKTIF ... HEBAT ...😃😍🤩🥰✍🙏🙏🙏
Hermoso proyecto, gracias por compartir. Saludos desde Venezuela.
I like it. Ur invention sounds so sweet. It says "coca coca cola"..😊✌️✌️ thank you very much.
Very interesting little ( or big ) devices ...
Love the DIY music. :)
well I have all the things I need to make this, I have the cans, the steel wool, the bicycle spoke, the 3d printer and so on. One question Where do you get that sheet with the gritty sounding stuff on it? At 00:14?
Keren banget karya abang kita ini,membuat mesin tenaga uap mini 😙😙😙
Muy buen video le dejare su respectivo like y compartir con mis smigos ❤❤❤❤❤😂😂😂😂
Yo tambien jajaja
Ya gracias amigo jajaja
De nada bro saludos trngo 40.000 subs
Nice project, love it!
Good vidéo bro 🔥👍
Thanks for the tutorial! Is there a place where I can find the STL files?
did you find out where the files are?
@@cosimometastasio3132 I have not, yet
@@armanda-s1776bonjour avez vous trouver les fichiers si non vous l'avez peut être modéliser vous même si c'est le cas pourrai-je avoir les STL via un lien mega
Merci d'avance
It's the first time I see 200 and 250 ml Coca Cans. 🤣 We don't have those in Québec.
Nice project, thanks.
iyi kardesim 👍👍👍👍👍👍
thanks man i will get aproveed on my class
You're the future James Watt
Great work keep up 👍
and it can generate electricity.
thx my frend.
@@ZAFERYILDIZ52 bonjour cette machine à air chaud est ce que elle fonctionne avec une bougie et sans eaux en vous remerciant !
Non, cela ne peut pas fonctionner sans eau car l'eau refroidit l'air chauffé (différentes choses se produisent pour refroidir l'air).
Cela fonctionne si la bougie fournit suffisamment de chaleur (écrit en utilisant la traduction, désolé pour les erreurs)@@johnpages4627
Love the music. It has a great Led Zep feel.
it does
Имба. Ты лучший продолжай
This is impressive
Its been a while but this is still a great tutorial! Any chance we could get those stl's?
Двигатель Стирлинга 👍
Nice 👍✔️🐾👏
Ellerine emeklerine sağlık ustam 👍❤️
Super 👍👋👋❤️
Браво. Този двигател може да бъде много полезен за руските танкове..през зимата.
Bloody hell, that is truly wonderful. Something so simple and I was smiling like a kid watching magic all the way through 😄😊
Thanks for the build. You know if you were to have a Fresnel Lens focussing on water at the base, instead of a paraffin lamp as the heat source, would that work?
can you use steel brush for dishes instead of steel wool?
tebrikler hocam, bir sorum olacaktı, alüminyum tel ne işe yarıyor bu projede
Please STL files it was a great tutorial!
ayrıca yeni müzik seçimleri muhteşem olmuş
Abi kolay gelsin pistona yerleştirdiğimiz çelik yünü bulaşık tellerinin üretildiği maddemi
O bir bulaşık teli zaten alüminyum tel
O çelik yünü yani çelik değilmi
Ellerine sağlık hocam
Helal olsun usta ellerine sağlık
Cool idea an built. Thanks for sharing.
Weekend Stuff
elinize sağlık
Bro can you please suggest alternatives for that fine aluminum wire? Will sponge work as well? Btw nice video
Steel wool
or the wore from umbrella maybe
bro, with stranded copper wire. is it possible for the piston?
U need the piston lightly as possible
Hello, great video! Where can I find the files to 3D print the parts
hocam mümkünse 3D printerda bastığınz 3D model dosyasını paylasibilirmisiniz? tesekkürler
So nice
certified gizmo.
what purpose does the aluminum wool serve?
Kolay gelsin hocam
teşekkürler kardeşim
Can use water pipe instead of 3D print?
Yes
I like the videos but in both you skip what the piece that is around the wire between the lower can and upper that keeps the steam in. The steam on the one I built keeps coming out of there,
Also what u the height of the longer bottle, i really need it because we are going to make a project like this ,thank you
What to do if you dont have that wire what to put
peut-on faire un moteur Stirling avec comme cylindre une bombe de WD40 au lieu d'une cannette de coca ? pas trop lourd ? j’aimerais faire 6 cylindres
Los archivos stl donde los encuentro? Dice que los subiran pronto pero no aparecen en la descripcion
Un vrai solex l’engin 😂
Also, should i place the piston at the bottom before cutting the top Portion
No, the purpose of the Gamma Type Stirling engine is to pass the hot air into the cold air intake. So your piston MUST go from the very top (to let the air pass through the chamber) and then go down (to let the hot air create pressure in order to lift it up)
Hello, how to get the stl files ??
Thanks you very much !
Hola , tienes los archivos de las piezas en 3d?
Usa un codo de pvc y una lata mas grande para poner el agua.
Zafer abi sana sorum olacak ama eski videodan abi çanak anten ile internet tüm yerde geçerlimi? Bide aylık kaç ödüyoruz internete? Cevaplarsan sevinirim
Nice project, love it !
Good 👍👍👍👍👍👍
bununla elektrik üretebilirsiniz hocam çok güzel
hi, do you have the models, you used in this model?
Good evening, may i ask if what is the length of the bottle that was used , also the distance of the pvc
is it real? I tried many time but fail
Yo lo Ise tal cual pero no funcionó que Cres que me esté fallando?
hocam acaba tek silindirli sterling motor da yapabilir misiniz?
Zaten öyle ki kardeşim
@@ZAFERYILDIZ52 jkdvgndjgdn nedense çok güldüm hocam ustam kendin yap rc araç yaparmısın :D
Yo busque en OLX y compre el mio en Bogota y funciona perfecto
super je l'ai fait pendant mais vacence
Hocam stl ler neree acaba saygılar
hola, en donde subiste los diseños 3d de las piezas?
why do so many people have a 3d printer? If they have that thing, they can make more impressive and cool things, why are you here?
просто и интересно.. продолжай творить...
Какое топливо для горелки?
abi STL dosyalarını paylaşır mısın
Its work ma bro ty ❤
Devirsiz ama yinede çok güzel
bro, I really need those stl files please can you give them to me?
esque sa pourais marcher avec de le laine de vers ou de roche
what is the materials
SUPER
Oh mga ka klase ko sa heat transfer eto na project natin. . O dikaya bagsak na tayo hahah
Did you fail or did it work??
Jealousy make you nasty
Stp les fichiers stl
hello, can i get the STL file?
Pouvez vous me donner les fichiers pour l'imprimante 3d svp
Alguien me puede decir que materiales utilizo porfa
You did not show how you seal the top of the piston
List of materials? please
ขอบคุณสำหรับสิ่งดีๆ
Abi 3d yazıcı parçalarıni nasıl alabiliriz
Potete mandarmi x posta un modellino? Sapere quanto mi costa. Grazie
A cosa serve il cd ?
9:38
Merhaba abi 3d yazıcıdan bastığın şeylerin stl dosyasını bana atabilir misin
Video açıklamasından indirin
@@ZAFERYILDIZ52 abi yakında paylaşılacak yazıyor
Can i get this project bro ❤️❤️❤️
Thanks my Frend
Abi yalnız mıtnakısla çalışan motor yaparmısın?
Parts required: 2 soda cans, balloon, bike spoke, steel wool......price, $200
Hahaha
Not working 😢😢
did you turn the flywheel?
X2 😢
Sao minh lam ko duoc nhi
WHERE ARE STL FILES?
👍👍👍👍👍
جميل جدا
Combien de chevaux 😂ou plutot combien mouche 😂😂😂😂 en tout qu'à superbe je v en faire un avec des tonneaux 😂😂😂
🎉🎉🎉🎊🎊🎊👏🏻👏🏻👏🏻🤗🇦🇷
you stil this engine from chanel Дмитрий Петраков
Kesini gra² TT