Following from 🇧🇧..... great build and I respect how you've took the time to answer ppls queries and provide info.... mad respect 🙏🏾.... best of luck with your machine
Awesome build man! You can see that you really put effort in making your videos. Keep it up! Do you have a video on that 5 lug conversion? I wanted to do something similar on my CS3 2005 lancer.
Appreciate it man. I don't have a vid of the 5 lug conversion, as that was a straight bolt up. But I do have a vid going from cs 5 hole to the brembos on the channel.
They are supposed to yea. Mine making noise as well. You need to take them out an clean them or get then replaced. I'm using 5w40 oil and not going to go any thicker than that
Is the 4g15 sohc 92 HP out of the Mitsubishi Mirage 97-02 similar to the 4g15t? Im in USA and would love to do such a swap or know where to get replacement parts if something broke. Thank you in advance
The block should be similar but the head will be different being mivec and turbo. You should get the full engine and transmission conversion. Will work better.
Thanks man. That's a tablet I put in. The maxxecu has Bluetooth and it's outputting to the tablet. If u check my channel, you will see the install vid for the tablet
Funny you say that. I've been using the AWD 4g15 flywheel. Those has the dowels already in position to use a mivec 215mm clutch and pressure plate combo. What i use is the ACT extreme clutch and pressure plate rated for 450tq
Nah I don't have a pin out for it. I used the same wiring harness I had for the 4g15, I just wired in the mivec. And then the crank sensor jack had to change
How about the mivec WIRE? Did you change the ECU? Coil wire? Its just jumped? 4g15 SOHC dont have pin out for mivec But how to set up this solution? Thank you
I'm running a maxxecu standalone unit. So that made it easier for me. Without that, I would not be able to start the car without the original mivec ecu
Hello, I got a 4g15T engine colt rs, just installed maxxecu mini on it. I am not having fire when I enable cam input(1 pulse)… however, when I disable cam input, I get fire but engine won't run in sequential. can you help with setting please?
What trigger patter was used? We left 1 on the cam and the one on the crabs was normal. So the trigger pattern is similar to the evo 10 trigger pattern.
@@danielpersad5789 I am using evo 10 trigger setup for the crank since its same but for the cam, rhe pattern is not quite similar to evo x…just sent you a message on facebook, can we communicate there?thanks
thats stock 4g15 twin cam mivec? it mean will fit at 4g18 right..just to know what you mention at crank sensor..must change to activate the mivec using maxxecu?
It's a built 4g18 block and a stock 4g15 mivec head. In order to activate the mivec, you would need the crank trigger to work, so the ecu can see it. Otherwise, it can work with the stock 4g18 crank, but you may not be able to activate the mivec
Hey, it's the same cover. I just added 2 10AN ports to fit my catch can. I'm running alot of boost, so needed to make sure the head was vented properly
Normal driving you can feel the difference for sure. Alot smoother etc. We have to go to tune on the dyno to really see the difference with full throttle runs
@@danielpersad5789 nice man looking forward to seeing the results, do you think the mivec head can fit on a 4g18 block? Im currently running 4g15 twin cam on a 4g18 block with high compression pistons, was thinking about boosting as the car runs quicker than a normal 4g15 twin cam but considering changing the head first (its a ck2 lancer btw)
The head is a direct bolt up. But you would need the oil pump, water pump, trigger wheel and the ecu. I'm using a maxx ecu, standalone ecu,so we used that to start the car.It can work with the 4g18 yea. Boost is life!
hey nice build , i have a 1998 lancer ck2a body , the stock engine was a 4g15 but the intake is a carburettor , how much work will it take if i would make it into a 4g15 dohc mivec? do i need to change a lot of parts inside like the tank or something?
Hey thanks man. You would need the parts I used, and also change the pump in the tank. It would be better to get a fuel injected gas tank as that has a baffle in the tank, which is better. You may have to run some fuel lines back to the fuel tank, but it shouldn't be too much work to do.
@@danielpersad5789 i was thinking about putting this engine into my lancer cs3 too, but workshop is worry about that this engine ecu won't be compatible with abs and airbag.
@@danielpersad5789 i think you are right, there are ecu for abs and airbag. Will try to source for this engine. By the way what gearbox you are using? My lancer is using ck4 version gearbox, but i search online some one manage to bolt it up to this 4g15 mivec.
We used the evo 10 trigger Pattern. That had to be tweaked a bit to start. For the mivec to work, you would need to use the 4g15 mivec trigger and cam trigger as it uses that to know cam position to set mivec. If u don't want mivec to work, it's possible to use the 4g18 cam an crank trigger
You use 4g15 box from colt czt? I have use lancer MX gearbox it bolt up direct to 4g15t but i had to move my slave cylinder a bit forward because of turbo original place Do you think thats the cause for slipping in changing gears? I wonder was box you use and what is you clutch setup if you dont mind helping
@@yaseenpeerally6722 I'm using tbe gearbox from tbe 4g92 mivec. Those made to swing 8500+ rpm. I'm also using an act clutch an pressure plate. Slipping in changing gears may be your clutch going bad and requires replacement
If your transmission is cvt, I don't think it will work with the 4g15T from the colt. The transmission that comes with the 4g15t is a normal type, non cvt
I'm running a standalone management. Maxxecu. If you are putting this engine you will need the original 4g15t ecu or a standalone. 4g18 won't work as it has to control fueling for boost and mivec activation
Following from 🇧🇧..... great build and I respect how you've took the time to answer ppls queries and provide info.... mad respect 🙏🏾.... best of luck with your machine
Thanks for following! Trying to keep content as I don't see anyone else doing this. Plenty more to come!
@@danielpersad5789 it's true....
@@trick4071 yep. New vid will be out later this month
@@trick4071 yea I am. Daniel.j.e persad
Always used to see this car by piarco lights going across on mornings, love the build bro 👏🏼👏🏼👏🏼
Thanks man. Appreciate it
Loving it bro. Great work by all involved. 👏🏾
Thanks man!
sorry but that shop room floor.... my word... love it
Thanks man!
Do You know if i can swap My 4g13 to a 4g15T with same transmisión and wearing arness of My Lancer 4g13?
It's possible it may work once the transmission is not cvt. Harness from the 4g15t should work. I haven't tried it, but I believe it may
Awesome! Can't wait to see you at the, dyno!
Yessir! And you should be there to!
Glad to see you got through with the mivec head bro looking forward to the dyno video
Thanks man
Yoooo this was vibes. Great video. Keep up the good work 🙌🏽👊🏽
Thanks pal!
Awesome build man! You can see that you really put effort in making your videos. Keep it up! Do you have a video on that 5 lug conversion? I wanted to do something similar on my CS3 2005 lancer.
Appreciate it man. I don't have a vid of the 5 lug conversion, as that was a straight bolt up. But I do have a vid going from cs 5 hole to the brembos on the channel.
That's awesome project bro. Greeting from indonesia.
Thanks man. Appreciate it!
Love and appreciate the content bro! Keep up the hard work!
Thanks man 🙏
Nice work looking real good😍...love the yellow finsh
Yessir! According to bassy, that's penal yellow!
@@danielpersad5789 yes boy, the Penal Yellow !
Well it was done in penal after all😂
@@navinroopnarine 🤣🤣
Does the 4g15 have adjustable lifters cause I'm really tired of the ticking noise I already change oil using 10w 40
They are supposed to yea. Mine making noise as well. You need to take them out an clean them or get then replaced. I'm using 5w40 oil and not going to go any thicker than that
Is the 4g15 sohc 92 HP out of the Mitsubishi Mirage 97-02 similar to the 4g15t?
Im in USA and would love to do such a swap or know where to get replacement parts if something broke.
Thank you in advance
The block should be similar but the head will be different being mivec and turbo. You should get the full engine and transmission conversion. Will work better.
Yo I have a 4g15 twin cam in my cs2 and I wanna do this kinda setup but not turbo you have a contact need some info asap
Sure man. 356-4483
Great work but what is the kind of screen that showing engine data and how you put in there . I have the same dash
Thanks man. That's a tablet I put in. The maxxecu has Bluetooth and it's outputting to the tablet. If u check my channel, you will see the install vid for the tablet
@@danielpersad5789 ok i will check it and make a subscribe to 👉👏👏
Thanks very much!
брат, что зы выхлоп?
Custom made ram horn top mount manifold now with a 3 inch down pipe
What is clutch solution? In Russia we solving it by redrilling flywheel and instilling 215mm disk and clutch
Funny you say that. I've been using the AWD 4g15 flywheel. Those has the dowels already in position to use a mivec 215mm clutch and pressure plate combo. What i use is the ACT extreme clutch and pressure plate rated for 450tq
Красавчик👍👍👍👍
Thanks!
Any wiring diagram for the mivec ecu pinout I'm doing a swap but don't have the pin out and the engine won't accelerate any idea?
Nah I don't have a pin out for it. I used the same wiring harness I had for the 4g15, I just wired in the mivec. And then the crank sensor jack had to change
How about the mivec WIRE?
Did you change the ECU?
Coil wire? Its just jumped?
4g15 SOHC dont have pin out for mivec
But how to set up this solution?
Thank you
I'm running a maxxecu standalone unit. So that made it easier for me. Without that, I would not be able to start the car without the original mivec ecu
Hello, I got a 4g15T engine colt rs, just installed maxxecu mini on it. I am not having fire when I enable cam input(1 pulse)… however, when I disable cam input, I get fire but engine won't run in sequential. can you help with setting please?
What trigger patter was used? We left 1 on the cam and the one on the crabs was normal. So the trigger pattern is similar to the evo 10 trigger pattern.
@@danielpersad5789 I am using evo 10 trigger setup for the crank since its same but for the cam, rhe pattern is not quite similar to evo x…just sent you a message on facebook, can we communicate there?thanks
@@oodeyengovindareddi6423 ok no problem. I will check the message and respond to you
311whp calling it now
The classic mitsu belt sqeak
Cant get away from it lol
Right there in the pune boi ite
Lol yea. Went to check a friend there
thats stock 4g15 twin cam mivec? it mean will fit at 4g18 right..just to know what you mention at crank sensor..must change to activate the mivec using maxxecu?
It's a built 4g18 block and a stock 4g15 mivec head. In order to activate the mivec, you would need the crank trigger to work, so the ecu can see it. Otherwise, it can work with the stock 4g18 crank, but you may not be able to activate the mivec
Is the valve cover reworked ? I have a czt with 4g15t and it looks different
Hey, it's the same cover. I just added 2 10AN ports to fit my catch can. I'm running alot of boost, so needed to make sure the head was vented properly
Sweet
Обожаю твой билд. Из России наблюдаю
Hey, can you send this over in english?
Love it bro, with changing the head u felt any difference or only the dino will show?
Normal driving you can feel the difference for sure. Alot smoother etc. We have to go to tune on the dyno to really see the difference with full throttle runs
@@danielpersad5789 nice man looking forward to seeing the results, do you think the mivec head can fit on a 4g18 block? Im currently running 4g15 twin cam on a 4g18 block with high compression pistons, was thinking about boosting as the car runs quicker than a normal 4g15 twin cam but considering changing the head first (its a ck2 lancer btw)
The head is a direct bolt up. But you would need the oil pump, water pump, trigger wheel and the ecu. I'm using a maxx ecu, standalone ecu,so we used that to start the car.It can work with the 4g18 yea. Boost is life!
@@jordanpena4573 it will work.. i have a 4g18 block with 4g15dohc mivec head
Hi Daniel, have some family in TnT looking for a good mechanic for a 2002 Lancer Cedia GDI 1.5.
Thats a hard one as alot of people are not familiar with it. My dad is a really good mechanic and I'm sure he can sort it out. Persad-726-1579
They ended up selling the car. Seems too complicated a fuel design. Thanks for the reply though. @@danielpersad5789
hey nice build , i have a 1998 lancer ck2a body , the stock engine was a 4g15 but the intake is a carburettor , how much work will it take if i would make it into a 4g15 dohc mivec? do i need to change a lot of parts inside like the tank or something?
Hey thanks man.
You would need the parts I used, and also change the pump in the tank. It would be better to get a fuel injected gas tank as that has a baffle in the tank, which is better. You may have to run some fuel lines back to the fuel tank, but it shouldn't be too much work to do.
enjin 4g15 1993 ble pasang c head ni?
Yea u can. But this is not distributor type. So u will need the ecu with the head to control it
head dia ni ble pnp? wiring ble tukar
The head is plug and play yes. Direct bolt up
رأس المحرك لأي سيارة ؟ evo ؟
The head came off a 4g15 mivec turbo engine from the Colt R
Yo bro I have a ck and I want to meet up with y'all
Sure man. Will be at the next autocross on May 20th at wallerfield
Bro where did u get those headlights ?
Those are ebay headlights
Can tell what cams u use,?wat cover use,?what coil pack u use? ,and wat block it on ?
This is the 4g15 mivec head from the colt r. Stock head,cover,cams,coil pack from the colt. It's on a 4g15 sohc block that came in the cs3 lancer
@@danielpersad5789 I thought u use the ck head with 4g92 mivec head,mivec cover,cams
Nah I didn't. The ck 4g92 head would not line up the the 4g1x series of blocks
@@danielpersad5789 yh correct
So this is a colt 4g15T mivec head? Are you using maxxecu to activate the mivec? I was told it was a vvt mivec.
Yes correct. I'm wiring in the mivec this weekend and the maxxecu will be controlling it.
@@danielpersad5789 i was thinking about putting this engine into my lancer cs3 too, but workshop is worry about that this engine ecu won't be compatible with abs and airbag.
I don't see why it won't work with abs and airbag. That has a separate control system. U just changing engine and the ecu for the engine. Thats it
@@danielpersad5789 i think you are right, there are ecu for abs and airbag. Will try to source for this engine. By the way what gearbox you are using? My lancer is using ck4 version gearbox, but i search online some one manage to bolt it up to this 4g15 mivec.
I'm using a ck mivec gearbox. All those blocks supposed to have the same bolt up
What cam trigger pattern setting you use in maxx ecu? And can it run 4g18 crank trigger with 4g15t custom 1 tooth cam trigger?
We used the evo 10 trigger Pattern. That had to be tweaked a bit to start. For the mivec to work, you would need to use the 4g15 mivec trigger and cam trigger as it uses that to know cam position to set mivec. If u don't want mivec to work, it's possible to use the 4g18 cam an crank trigger
@@danielpersad5789 hey Daniel would you mind sharing what transmission did you use? I have similar engine swap
@@yaseenpeerally6722 hey. I'm running a mivec gearbox. It was a direct bolt up to the 4g15. This gearbox has better ratios
You use 4g15 box from colt czt?
I have use lancer MX gearbox it bolt up direct to 4g15t but i had to move my slave cylinder a bit forward because of turbo original place
Do you think thats the cause for slipping in changing gears?
I wonder was box you use and what is you clutch setup if you dont mind helping
@@yaseenpeerally6722 I'm using tbe gearbox from tbe 4g92 mivec. Those made to swing 8500+ rpm. I'm also using an act clutch an pressure plate. Slipping in changing gears may be your clutch going bad and requires replacement
I have a question. I have same 4g18 car and i wanna swap it to 4g15t. Is it compatible on stock transmission?
If your transmission is cvt, I don't think it will work with the 4g15T from the colt. The transmission that comes with the 4g15t is a normal type, non cvt
@@danielpersad5789 i have manuel transmission.
@@mtoyanik oh well you are good to go. It will bolt up and work
@@danielpersad5789Will the Cs transmission hold up the power from the 4g15t engine?
@@akhmau84 is it the cvt transmission?
Where u get ur turbo kit?
This was custom built
How much more hp you think you make
Definitely hoping to see over the 300whp mark. Will be carrying the car to the dyno next month, so we will find out then!
And how power u make on dyno
Will be carrying it to the dyno next month. Will know then
Bro how were you able to activate the mivec?
I have the same head, but the mechanic suggested to just install a switch for the mivec
I'm using the maxxecu race standalone and the mivec is wired and activated from it.
@@danielpersad5789 what did you do with the old ecu?
So your mivec now works based on a specific rpm?
@@amir3992 I have the original ecu for the mivec at home. For sale. The car still needs to be tuned but we can set the mivec to come on at any rpm
@@danielpersad5789 will the harness of the cs3 fit on the mivec ecu?
4wd or 2?
It's 2wd
@@danielpersad5789 you have a cool car)
Thank you very much 😁
Does it run 4g18 ecu? Or I must change it to 4g15t ecu?
I'm running a standalone management. Maxxecu. If you are putting this engine you will need the original 4g15t ecu or a standalone. 4g18 won't work as it has to control fueling for boost and mivec activation
@@danielpersad5789 thanks a lot
@@mtoyanik no problem
Stock internal?
I'm running maxpeeding rods and vitara semi forged pistons. So far I'm at 326whp 275tq
Lol all that work an a sr cutting ass normal... But bug up nice build yes
Thats how it goes! You will never be the fastest out there! But thanks!
Hi, which gearbox on it bro
I'm using a 4g92 mivec gearbox on this setup. The ratios in this works better in my setup for autocross, faster acceleration
@@danielpersad5789 thanks bro currently setting up one, will look for the gearbox
@@AhadHHH ok great!
songs? 😅
Huh?
Does the car have ac
Yes it does