Simple Flyback Converter, Transformer Design TNY267

$2 for 1-4 Layer PCBs, Get SMT Coupons: jlcpcb.com/DYE
►Simple Flyback Converter, Transformer Design TNY267
►Hi Friends. Simple Flyback Converter, Transformer Design TNY267. I hope you like it
►With JLCPCB SMT assembly it saves me 10 times more time than before.
►SMT products from JLCPCB : • Design Full Battery Pr...
►You can download all file below.
drive.google.com/file/d/1crui...
***************************************************************
I hope you like my project, you can give me a coffee to make a new video of high quality.
***************************************************************
Donate me click here: paypal.me/LongTechnical
Contact me on Gmail: [e-mail]
Have a nice day my friends
***************************************************************

[@MrRvdbeek]

That’s what I need. simple and working great with protection.
So thanks 🙏

[@LongTechnical]

Thank you so much

[@taposhdeb2196]

Thanks for sharing.

[@vreism]

Perfect thank you

[@Bianchi77]

Creative video, thanks for sharing, like it :)

[@dilikash851]

Получилось классно

[@transparentlab8318]

Splendid

[@nourddinebimgdi4840]

thanks a lot!!

[@electronic7979]

Very good

[@LongTechnical]

Thank you bro

[@Edmorbus]

Thanks for sharing

[@LongTechnical]

Thank you bro

[@mariote1359]

There is my like, tanks bro.

[@LongTechnical]

Thank you so much

[@easirarafat6771]

Thank you sir and nice job❤️

[@LongTechnical]

Thank you bro

[@MrFlexxip]

very nice project thank you

[@LongTechnical]

Thank you bro

[@quanghoang04]

👍👍

[@kabandajamir9844]

So nice

[@LongTechnical]

Thank you so much

[@homeelectronic1775]

Hi. Very nice brother

[@LongTechnical]

Thank brother

[@detanatorxxx52]

If we use 5volt zener diode, does it still work? And how about the power? How much watt?

[@yuribiktop6595]

Can you also use this design for DC to DC smps by removing the diode rectify?

[@waterfuel]

What about isolation of 2 grounds? I see an optocoupler for feedback volts regulator.

[@lumivex]

How many turns of insulator tape after the primary windings?

[@mikeunivers]

Do you have any transformer source for a 18v drill

[@sagorrana2051]

if I don't connect feedback ,what will be the duty cicyle?

[@nuradhim97]

Hi sir, can you explain why some smps use inductor filter at the output while other not?

[@davebalino]

Hi, great work, is it possible to increase the current to 5 amps? -new susbcriber

[@anlpereira]

Hi, I didn't find the Relay charging circuit that is showed in the schematic. Thanks

[@LongTechnical]

Relay ? Don't have any relay in this circuit bro

[@AP-hz8or]

is there a 110V version most power in us 110 volt

[@alphaoffrance617]

This supply work from 80 volt to 220 volt grid lines.
Both combination is available inside the supply.

[@masterinembeddedc7376]

How to make 50v 10 amp flyback power supply 220v to 50 use this mathood possible ?

[@LongTechnical]

Same method is OK bro. But using UC3843,3844,3845 with mosfet. Not this IC

[@alphaoffrance617]

Can i replace 12 volt zener with 15 volt, to get 15 volt output ?

[@LongTechnical]

Of course bro

[@yuribiktop6595]

Insulator tape was wrapped how many times ? 15v 3A can I get it?

[@LongTechnical]

8 layer or more bro. No bro. Max 1,5A at 15V. I will design new circuit for 5A or 10A next video

[@ezeoluchukwu5104]

THE MAN THE MAN WELDON

[@lymmentrixprofessional]

That will be great

[@diablo66634]

Good Job, What are the characteristics of the output inductor?

[@NoviSavvy]

In a flyback you may not need an inductor in the output since the transformer works as an inductor. This does not apply to push-pulls and forward converters of course. I've seen expensive industrial equipment without an inductor in it's flyback PS. But you can download software from the manufacturer of the IC which I think will tell you this depending on your output parameters

[@Unajaclosp]

Why do you need a air gap in the core?

[@LongTechnical]

Because it is a flyback converter. You can search it detail on internet

[@robr8554]

Because the gap reduces the magnetizing inductance where the energy is stored. If the gap is zero there would larger reluctance and no energy is stored. You need the gap since this is a coupled inductor not a transformer.

[@NguyenDinhGioi]

Ko có bản tiếng việt ah bác

[@ShakeelAhmed-cx7lz]

Bro make a 50volt 20amp power supply. With feedback

[@LongTechnical]

OK bro

[@phenome4973]

can you share the Gerber files for this project for JLC PCB

[@LongTechnical]

I remember i shared it. please check link in description

[@phenome4973]

@@LongTechnical Thanks 😁

[@yuribiktop6595]

Can you design for dual Outputs 12v 2A and isolated 18v 1A Smps?

[@LongTechnical]

The power of this circuit max 20W bro. With your request, we need another circuit

[@yuribiktop6595]

@@LongTechnical okay i am waiting for that. Also why your winding direction is anti-clockwise?

[@yuribiktop6595]

@@LongTechnical better if is a DC- DC flyback converter input min 12v to 55max . Output 13v non-isolated and 21v isolated outputs

[@LongTechnical]

It't OK bro

[@edisetiyono3644]

Berapa Amper ini bro..?

[@boxingfavsmg]

Is this AI generated . Something doesn’t seem right.