You bet, I felt your pain and vowed to document ALL the settings after watching 5 or 6 videos that seemed to always skip over something that turned out to be critical to getting flying.
I just got a blade inductrix in the mail. While my battery was charging I set up my DX6i just like you have yours set. Took 1 click of forward trim and it was hovering almost perfectly. Thanks a lot for the write up as the instructions that come with it don't do much. I think I know what the flap switch is for but I have not a clue what the gear switch is supposed to be doing.
Man that's awesome, how did you get it to arm? What position where all the switches in? I can't get mine to arm, followed his video exactly too. Thanks
@@dempsey96 to be honest I don't know. I set mine up like he did in the video and it just worked. I did have a minor problem at first. Seems as though after turning on the transmitter if I connect the battery on the Inductrix too quickly it won't work. Try turning on the transmitter and then give it about ten seconds before you plug in the battery. This was all it took for me.
Thank you, this video is great! I'm just having one problem. When I lift off of the ground, it starts flying backwards on its own. Any idea why? Any help is greatly appreciated.
Here is the programming for the Inductrix FPV+ using the DX6i. This is the only setup that works, and it provides all three flight modes. ○ DX6i: Flaps: 98dn/100up Mix1 Gear → Gear Rate D -100% U 0% Switch ELE D/R ( for 3 flight modes )
I have the DX8G2. Played with travel & expo %’s & WAMMY! I’m buzzin round in the wind no prob. Still learning about all this though. Just think how cool it would be if I understood 1/2 of what I did. Lol
I need some help please, I followed your video exactly and can not get it to arm. What do I need to do? I'm ready to throw this thing out the window haha! Also, what position do you have the switches set to when you arm it? Thanks for the help!!!
Yes I finally got it. I'll try to explain what I did...I'm new to quads and the dx6i so bear with me haha! Under travel adjust, I was incorrectly setting a few things. For ELEV, you have to pull DOWN on right ELEV stick (I thought it was the toggle switch) and while holding it down set it...mine is DOWN 115%. I also had to adjust throttle DOWN endpoint, as after getting it to arm and flying as soon as I went past a certain point on letting off throttle it would cut off the quad and have to re arm. Obviously you can't fly like this, as letting off throttle meant the quad would just fall out of the air. I also enabled THROTTLE CUT, as it made it easier to disarm. Make sure you have FLAP set correctly...I set mine to UP 100% (toggle up) and DOWN 98% (toggle down). Let me know if this helps any! If it doesn't I can try to make you a video.
It seems that each radio is a little different as well, so it took me a little while to get it set up. Please let me know if you can't get it...I was ready to sell the whole darn set up! Once flying it is super fun. I will make you a video if you can't get it; just let me know. Are you on rcgroups.com? If so you can PM me, I'm Panhead5496 over there.
This video is INSANELY HELPFUL. Smile to yourself as you are helping random ppl around the world
You bet, I felt your pain and vowed to document ALL the settings after watching 5 or 6 videos that seemed to always skip over something that turned out to be critical to getting flying.
Thank you.. worked perfect... My DX6I lives to see another day..
I just got a blade inductrix in the mail. While my battery was charging I set up my DX6i just like you have yours set. Took 1 click of forward trim and it was hovering almost perfectly. Thanks a lot for the write up as the instructions that come with it don't do much.
I think I know what the flap switch is for but I have not a clue what the gear switch is supposed to be doing.
Man that's awesome, how did you get it to arm? What position where all the switches in? I can't get mine to arm, followed his video exactly too. Thanks
@@dempsey96 to be honest I don't know. I set mine up like he did in the video and it just worked. I did have a minor problem at first. Seems as though after turning on the transmitter if I connect the battery on the Inductrix too quickly it won't work. Try turning on the transmitter and then give it about ten seconds before you plug in the battery. This was all it took for me.
Thanks for the response. I finally managed to get mine to arm! That's odd about the binding thing! Mine binds instantly.
How the heck do you bind it?
You are the man!!!!! You got me flying when no one else could. Thank you so much great video and I sub'd.
Cool. So glad it helped. I learned a bunch about programming by learning from other vids, then running into trouble. It all made sense, after a while.
Thanks for the info. The flaps set at 100 / 100 did not work for me to arm the quad. 45 /45 did work just fine.
thanks champ you have made my day couldn't work out why it wouldn't work but because of your vid no it arms properly an is ready to fly
👍
the flap switch on my dx6i is broken is there anything i can do
Thanks this has me finally flying it great job.
Woohoo - yeah!
Thank you, this video is great! I'm just having one problem. When I lift off of the ground, it starts flying backwards on its own. Any idea why? Any help is greatly appreciated.
I haven't flown in a while, I would have to dig these out and think about it - others would probably be able to help faster than me...
No problem
thanks bro, i wanted to give my old setup to someone with the FPV Plus, I could not for the life of me get it. THANK YOU! Just subed... ur the poo!
Thank you for the video
Thank you very much for the awesome video
Here is the programming for the Inductrix FPV+ using the DX6i. This is the only setup that works, and it provides all three flight modes.
○ DX6i: Flaps: 98dn/100up
Mix1 Gear → Gear
Rate D -100% U 0%
Switch ELE D/R
( for 3 flight modes )
Good tip, I will have to try that.
I have the DX8G2. Played with travel & expo %’s & WAMMY! I’m buzzin round in the wind no prob. Still learning about all this though. Just think how cool it would be if I understood 1/2 of what I did. Lol
Yeah, I actually learned how the radio worked by making it sync up with the Ind FPZ. Less of a mystery.
I need some help please, I followed your video exactly and can not get it to arm. What do I need to do? I'm ready to throw this thing out the window haha! Also, what position do you have the switches set to when you arm it? Thanks for the help!!!
Same here... I've been fussing with this for about an hour now and can't figure out how to get it to arm on my DX6i. Did you ever figure it out?
Yes I finally got it. I'll try to explain what I did...I'm new to quads and the dx6i so bear with me haha! Under travel adjust, I was incorrectly setting a few things. For ELEV, you have to pull DOWN on right ELEV stick (I thought it was the toggle switch) and while holding it down set it...mine is DOWN 115%. I also had to adjust throttle DOWN endpoint, as after getting it to arm and flying as soon as I went past a certain point on letting off throttle it would cut off the quad and have to re arm. Obviously you can't fly like this, as letting off throttle meant the quad would just fall out of the air. I also enabled THROTTLE CUT, as it made it easier to disarm. Make sure you have FLAP set correctly...I set mine to UP 100% (toggle up) and DOWN 98% (toggle down). Let me know if this helps any! If it doesn't I can try to make you a video.
It seems that each radio is a little different as well, so it took me a little while to get it set up. Please let me know if you can't get it...I was ready to sell the whole darn set up! Once flying it is super fun. I will make you a video if you can't get it; just let me know. Are you on rcgroups.com? If so you can PM me, I'm Panhead5496 over there.
@@dempsey96 would love a video. Can't get mine to arm!
I will try to make a video tonight and post it! I'll link it here for you.