I learned from this video that you need a router to establish a communication between two PC which belongs to the different VLAN. And we need two create interface on that router. When traffic sent from PC to switch then it further go to router even if the another VLAN is in same switch. So the router can then to the switch and then to the PC. Thanks for making this video.
Dear @pm networking, for the intervlans, does it neccessary create ACL in the router or create a routing table? Other way, where it is the security if all the vlans can communicate each other?
Please discuss Native Vlan and why need to change it how to Change it and the difference between Sub interface and SVI and its use, layer 3 and 2 port channel, conditions of use With Labs
Hi sir, i did this exact scenario and used Multi layer switch 3560 instead. then I can not trunk it to connect to router or other switch. why is that ?
What if i have only vlan 10 on switch and vlan 20 on other switch , i want to know the link between switches will be access or trunk ?? And also the link between switch and router will be access or trunk and why ??
The link between two switches will be trunk and and same for router because we need a port to pass a vlan out of the switch so this is done by a trunk port. A trunk port is designed to pass the multiple vlans.
You also can have portaccess link between the switches, but you will need one cable to each vlan and 2 cable to connect to 2 interfaces on the router one fir each vlans.
If i configure vlan 10 as native vlan in all switches, then the switch will forward the frame from vlan 10 untaged. At this point when the router receives an untagged frame how will the router know it is from the native vlan?
Sir router below that two switches then both switches are connected to a single switch and from that switch 6 pc s are connected, how can I configure this scenario
Hello, I'm Adrian, I don't know that you can't ping two hosts in a vlan on a 48-port 3com switch so that it receives the ping, can you explain it to me please, regards.
I learned from this video that you need a router to establish a communication between two PC which belongs to the different VLAN. And we need two create interface on that router. When traffic sent from PC to switch then it further go to router even if the another VLAN is in same switch. So the router can then to the switch and then to the PC.
Thanks for making this video.
The router could be part of pc
happy to got my missed lecture. love from Pak
Most welcome!
sir , here we dont have to configure routing protocol like OSPF right ? on what situations do we need to config routing Protocol ?
As always top notch teaching!
Thanks for appreciation 🙂
Dear @pm networking, for the intervlans, does it neccessary create ACL in the router or create a routing table? Other way, where it is the security if all the vlans can communicate each other?
Yes we have another way also
ive tried this step with different subnets like /24 and /16 with dhcp pool but not working. any advise?
Thanks, you helped me a lot.
Glad I could help!
Please discuss Native Vlan and why need to change it how to Change it and the difference between Sub interface and SVI and its use, layer 3 and 2 port channel, conditions of use With Labs
Videos already available on channel
hi, is it normal for a vlan can't ping the router, while the router can ping the vlan... and vlan 10 and 20 can't ping each other also
is it necessary to make the sub interface in 0.1 like means may we give number others 0.1?
Hi sir, i did this exact scenario and used Multi layer switch 3560 instead. then I can not trunk it to connect to router or other switch. why is that ?
Very easier method how you have taught us.plese upload effective video on SD wan Cisco viptela
Noted
What if i have only vlan 10 on switch and vlan 20 on other switch , i want to know the link between switches will be access or trunk ?? And also the link between switch and router will be access or trunk and why ??
The link between two switches will be trunk and and same for router because we need a port to pass a vlan out of the switch so this is done by a trunk port. A trunk port is designed to pass the multiple vlans.
You also can have portaccess link between the switches, but you will need one cable to each vlan and 2 cable to connect to 2 interfaces on the router one fir each vlans.
Sir can we connect other router rip ospf with it?
Yes
@@PMNetworking Sir can pls make vedio on it humble request from me
You are very helpful thank you, but just a little constructive criticism, you tend to shout alot, maybe just tone down your voice volume a little.
Thanks for feedback
If i configure vlan 10 as native vlan in all switches, then the switch will forward the frame from vlan 10 untaged. At this point when the router receives an untagged frame how will the router know it is from the native vlan?
All untagged traffic will be considered as native vlan traffic
how to configure router that connected with one switch and that switch again connected with 2 switches which has vlan 10 and 20
Hi how to create trunk and whats the usage pls explain
Noted
can you please add the .pkt file in discription tomorrow im having exam and need that urgently please
Check description
which version of cisco packet tracer you had used????
Sir router below that two switches then both switches are connected to a single switch and from that switch 6 pc s are connected, how can I configure this scenario
if we need to communicate between 2 diff vlan without router can we ?
Yes, You can do by creating svi on multilayer switch
nice content btw
Thank you for your feedback
Good work man thanks
Welcome
sir can u plz teach me
2 router 2 switch 4 pc VLAN provide me that video
Noted ✅️
Hello, I'm Adrian, I don't know that you can't ping two hosts in a vlan on a 48-port 3com switch so that it receives the ping, can you explain it to me please, regards.
ruclips.net/video/AZzzQeEp4UA/видео.html
Thanks
Welcome
Thanks bro..
Welcome
Spanning tree protocol ke bare main bto
STP is a Layer-2 protocol which is used for Layer-2 loop prevention.
To know in details watch my STP video.
Please show the truck option
Why using routable is addresses instead of private? This is bad
To reduce the shortage of ipv4 addresses
@@PMNetworking that would be private. So why using routable
How contact to you
my WhatsApp number is +918511826341
Sir please kindly
Sure
Please Hindi language
Sir not working
please don't shout
Noted
@@PMNetworking Thanks for explaining it so easily
you didnt configure TRUNK in this video..
And your number is incorrect
Stop shouting
Noted ✅️, this was my bad habit earlier 😅, check the latest videos
can you stop shouting?
Thank you
You're welcome