thanks for sharing that was thinking way outside the box on tilting the press on it's side. I would have tried all thread first with nuts on both ends, and it probably would not have worked. i will keep your idea in mind should I have to try something like you just did. Thanks again.
we do these all the time in the shop .Our way of doing it is to heat up rod eye with a map gas torch and before you press in new bushing place it in the freezer for about an hr ..They go in super easy
Yeah, I'll be trying your way next time. I knew about putting the bushing in the freezer but I forgot to do it before hand and didn't want to wait. Thanks for watching!
Us shade tree mechanics don't have dry ice laying around. I'm going to keep an eye out for something to cool them down. Even if it's just the computer cleaner aerosol. Thanks for watching!
What about a ball joint press? If it is not going I have seen people give the joint a whack with a ball peen hammer to shock it. Hard to argue against the press if that is what you have nice work.
your idea of turning the larger pins down to the smaller diameter wouldn't work . These pins are induction hardened only about .030 in depth , after you turned it off it's just a high carbon pin with no hardening , Most people that have access to a lathe use on size drill rod and cut it to length and drill grease holes in it
Great point. I'm glad I didn't turn them down. I'm still learning! I have a video on replacing the jack shaft on a vermeer 252 stump grinder. When I cut it to length, I noticed the outer was harder than the middle. Thanks for watching! And the comment
@@tomhendricks316 I heard you say something along the lines of having a lathe.. I'd get good at it and be able to make whatcha need and stick it to thw man
As you’ve shown- there’s more than one way to skin a cat (or replace a bushing). Nice job!
This is making the most work out this project.
Good job Tom. Use the tools you have. Great solution.
Thank you!
thanks for sharing that was thinking way outside the box on tilting the press on it's side. I would have tried all thread first with nuts on both ends, and it probably would not have worked. i will keep your idea in mind should I have to try something like you just did. Thanks again.
I tried all thread with the first curl cylinder bushing but all I had was 1/2" course and it stripped out.
Thanks for the comment!
Working on a 770 right now
4lb purse and a socket bout the same size works great
Maybe I'll try that next time. Thanks for watching!
we do these all the time in the shop .Our way of doing it is to heat up rod eye with a map gas torch and before you press in new bushing place it in the freezer for about an hr ..They go in super easy
Yeah, I'll be trying your way next time. I knew about putting the bushing in the freezer but I forgot to do it before hand and didn't want to wait. Thanks for watching!
@@tomhendricks316 if u can look around for a used king pin press it makes removing those bushings a breeze and u can leave the cylinder on the machine
dry ice and you can push it in with your fingers
Us shade tree mechanics don't have dry ice laying around. I'm going to keep an eye out for something to cool them down. Even if it's just the computer cleaner aerosol.
Thanks for watching!
Ball joint press might make things easier in the future.
nice fix
How about putting the bushings in the freezer for an hour. They will shrink when cold. You have to be quick once you remove them to press them.
Yeah, that's also a good idea. Thanks for watching!
I think the same way try something different great job
Do you know the part number for the bushings in the end of the cylinder?
Skip this question. The bushing package you showed is the correct number for the cylinder bushings
Skipped, but thanks for watching! Good luck with your project
What about a ball joint press? If it is not going I have seen people give the joint a whack with a ball peen hammer to shock it. Hard to argue against the press if that is what you have nice work.
Thanks Eric. I may try that next time
Thanks for watching!
tore my 580b apart, replacing all the bushings pins, thought about hmm take my press from hf and turn it sideways lol, u beat me 2 it
Yeah, I was like why not try it what do I have to lose.
Thanks for watching!
your idea of turning the larger pins down to the smaller diameter wouldn't work . These pins are induction hardened only about .030 in depth , after you turned it off it's just a high carbon pin with no hardening , Most people that have access to a lathe use on size drill rod and cut it to length and drill grease holes in it
Great point. I'm glad I didn't turn them down. I'm still learning! I have a video on replacing the jack shaft on a vermeer 252 stump grinder. When I cut it to length, I noticed the outer was harder than the middle.
Thanks for watching! And the comment
You need bushing stock my dude
I'm not that good at machining but I should get some in case I need it.
Thanks for watching!
@@tomhendricks316 I heard you say something along the lines of having a lathe.. I'd get good at it and be able to make whatcha need and stick it to thw man
Sounds like ur ringing a bell
It does kinda sound like a bell. Even more real time than it did in the video.
Thanks for watching!