(V-88),Home made 3phase bldc motor controller with sensor (Full bridge).
HTML-код
- Опубликовано: 12 сен 2024
- Here the 3 phase bldc controller is a full bridge driver and here 6 nos of irf- 44n MOSFET are used to make a driver.
It is a sensor type controller and 3 Reed switches are provided 120 degree each other and the signals are taken to driver.According to the sequence of the sensor signal the MOSFET are switched on and run the bldc motor.
#bldc #magnets #motor
Thank you so much sir! You are a saviour!
I could find schemes for half-bridge everywhere but your video is the only one I could find for full-bridge for last week. Really thank you!
I'm doing with sensorless motor, I might have questions in the future under this post..
Thanks for watching and supported
I have a question, for the positive side of the chipset, do we need P-type mosfets or N-type is used for both values?
Generally N type mosfet source terminal to be connected to negative and P type source terminal to be connected positive side
If you are using both N type mosfets connection may be changed
You try and check it sir
Thanks
I understand this. Glad you cleared that out!
Thanks again sir!
Sir ,so the sensor signal itself is acting directly as gate drive to the mosfet bridge???
Thank you !!
Helped a lot with a project
Very nice circuit. Will work good.
Thanks sir
I am very awe inspired by your video. Wonderful controller.
I have watched hundreds of BLDC motor videos and for the 1st time I have ever seen someone do what I wanted, create super cheap BLDC controllers using Reed switches instead of hall sensors or back emf sensors. Way to Go! I want to collaborate with you and make bigger motors for household appliances. Are you from Trichy?
Thanks sir
@@pugalstech How much maximum voltage and current circuit can handle?
I have used or 44n mosfet,so voltage and current may be 24v and 10 amps and sensor 3144 ic. so you have to choose according your requirement.
Hello, thank you for sharing your beautiful work.
Do either of the two circuits (Full Bridge or Half Bridge) allow CD-ROM Motor control with Hall Sensors?
P.S.: Is it possible to add a potentiometer to control the speed? Tks.
Thanks for watching and supported
how can i control the speed using that.
How are you generating the timing for the motor? Is there an analog circuit, or is there a microcontroller?
no
Microcontroller
Good Good Good !!!!
Very nice!
Thnk's
Thanks for watch and support sir
Good work
Thanks for sharing
Thanks sir
easily, simply make bldc controller,
save money ,time, .......
best of luck
Thank you sir
Sir, can you make a scheme without sensors?
Good work 👍👍
Thanks sir
Thank you very much Sir.
Very good sir 👍👍
Thanks sir
Can i use this for inverter compressor as tester
Can we speed control this bldc motor
Um giro de um motor sobre controle de frequência, satura a rotação em quantos rpm ?
Thanks sir
Sir by which source are you signal to the IGBT gate please explain that circuit
Muito bom.
Sensacional.😊❤
Thanks sir
sir this is six step commutation or FOC ?
Thanks sir
Great work,👍
Can u make & share 3phas BLDC controller with speed control circuit for Ac/dc sealing fan,
Operating Voltage is 220v & 12v,
Thanks
Thanks sir
Pls see my latest project, a bldc motor is run with ac and dc supply with separate controller
can you explain and show more on the signal sensor part of the circuit please.
Please see my" vedio V-59 sensor using reed switch"
Can I use for high current application where starting torque is high than normal .
Select Suitable Mofet for your requirements
Nice
Thanks sir
Dear sir i have a bldc compressor its voltage is 60-220v dc and it has three line (u,v,w)
Please give a mosfet for my bldc motor please sir i can make this but i don,t know how to select a correct mosfet please sir its really help full for me.i hope you reply
to me
*Motor amp is 15amp (max )
Hey just wondering what sensors you use, thankssss, it would be very helpful if you let me know as i am making this for my year 12 major project. Thankyou and congratulations on a great job!!
Details of sensor ,pls see the project "V-59 dual pole sensor using read switch"
Also what diodes do you use, are they 1N4007? thankyou
Yes sir
@@pugalstech thankyou so much mate you have no idea how much this has helped
Can this be used on a converted alternator to motor set up? I rewired an alternator to run as a motor for a project and need to power it with a controller
Thanks for watch
Ok possible but the motor should be 3phase, rotor permanent magnet type and voltage range should be less than dc 50v .Current 15 amps ,Thanks
Sir. En kitta hoover board bldc motor 2 irukku.. ada wechchi oru electric bike onnu seiyanum.. mudiyumenda adukku sariyana control onruda diagram thara mudiyuma.. ?? 36v, 350w need to use throtle. It is with sensor.. thank you
Thanks sir
வாழ்த்துக்கள்
@Pugals Tech How much maximum voltage and current circuit can handle?
With bigger finals, and higher wattage resistors and diodes, you can up the voltage and current considerably. Of course you need a motor big enough to present the load or you will not be challenging your controller. Don't try to make a half wave controller powerful enough to run a locomotive. Should be obvious, right?
Puedes poner subtitulos ,gracias .
Thanks sir
senior por favor subtitulos, gracias.
👌👍
Thanks sir
Sir how to make an esc bldc motor controller for 24 v car alternator bldc
Thanks sir
@@pugalstech sir pl give the video
Can i run a dc uvw compresar ?
Select proper switching MOSFET for your motor capacity, Thank you
@@pugalstech tnx
Can You share circuit diagram
This can use for 18 coil statar
12v
Yes ,possible for 18coil stator but the rotor pole should be 12 or 24 .In this case all 3 phase coils connection are clockwise
I am trying to use for Yamaha rx100 bike to as a starter motor after start using als charger to battery
Sir can u help
I have 18 coil stater
And 12 pole magnet
Magnet in left side of bike so anti clock wise need
Iam karaikudi
Sir circuit diagram this
Thanks sir
Pls send circuit diagram this
hello my great friend could you make a copy of this paper circuit available in my email? for a daring project of an electric Honda pop motorcycle replica???
Thanks sir
Muito bom?
Sir hall sensor circuit diagram
Sir pls see the video regarding your doubts in earlier project "New invention 3phase bldc motor controller with sensor" here clearly explain with diagram ok
Sekema
Sir hall sensor number
Hai brother here i using magnetic Reed switch only
And hall sensor using single phase bldc motor only
I will use the hall sensor for 3 phase bldc motor in my next project .
Thank you sir
@@pugalstech waiting
Change first your good camera after make videos 😊😊😊😊😊useless digram
Sorry for the incovinians