Installing an EMG Kirk Hammett Bone Breaker active pickup system.

I will take you through all the steps in removing the old passive system. Then installing the new EMG active system. you will need a good soldering iron, solder, nut drivers Metric and SAE, a number one phillips screwdriver, wire strippers, clippers and wire zip ties.

[@jklog69]

Excellent video again! I love seeing someone else who hates messy wiring. Very nice work sir.

[@guitarrx577]

Thank you! Got to keep it clean! thanks for watching.

[@singletakecovers9740]

Bought the hetset right after watching this. Excellent video from someone who knows what he’s talking about. The cherry on top was the test at the end. Very, very helpful.

[@guitarrx577]

Thanks for watching!!

[@jesusrevenga4132]

Best emg solderless tutorial, thank you man!

[@guitarrx577]

Thank you hope it was helpful !

[@douglassmith1544]

So I just was able to realize my dream... it was to rebuild/upgrade a guitar. I was able to do all the upgrades except I couldnt find a wiring diagram for the same exact switch u had in this video (it's what I have but just couldnt find research on it)
Thanks to your video I was able to know what contacts to solder and now have a guitar with a heck of alot more life and sass!

[@guitarrx577]

So glad it was a help to you Douglas! thanks for watching!

[@a.bo.5621]

Thanks a lot! Nice and helpfull

[@710clique9]

RX Thank you so much for this video! I have watched many on the subject and none were as clear and thorough as this. I have a guitar repair company and I am struggling with all things electric. I learned a ton from you.

[@Leper_Messiah.]

Thank you for taking the time to create this tutorial. I am going t be setting this exact setup in my Guitar. Very helpful, thank you.

[@guitarrx577]

Glad it was helpful thanks for watching!!

[@deaconpaulbuck4391]

Wonderful video. Thanks for taking the time through the install!

[@johnnilsson8474]

Awesome , thank you for this

[@nickdremow8726]

Thanks for the video my set should be here tomorrow!!

[@guitarrx577]

Hope you like them they sound great!

[@blackwolfgaming676]

Thank you so much for this video gonna use this for help when i order these pickups the first of the month

[@guitarrx577]

Glad to help! Thanks for watching and if you can share my channel!!

[@captaincrunch7661]

I didn't need to solder anything. I just left the wires on the switch. They go into the bus. It says it on the instructions.

[@fav8622]

Dean is awesome

[@tomduerr988]

Good video thanks

[@guitarrx577]

Glad you enjoyed it!

[@przemek3177]

If You don't want solder anything, better buy 3-way selection switch..😊EMG then just connect wires with quick connectors and is done.

[@chokolap7436]

How can i do the back plate on magnets?

[@r.e.dbituches1582]

Aprox. How much time the battery Lives? Even if you unplugg the cable?

[@JRM.Guitar]

Is there any way you can do this without a saw during iron

[@ryanbobadilla2527]

Do you follow the same instructions for a three way toggle switch on a Les Paul?

[@guitarrx577]

It's a little different the instruction sheet has the LP switch directions. You can also find the diagram on line if you don't have the sheet.

[@vevz7286]

not sure if this is a late comment but if i had a three pickup guitar should i just desolder the middle pickup and use the wires for the neck and bridge for the battery buss?

[@deaconpaulbuck4391]

I finally purchased a couple EMG pickups an plan to follow your video the best I can. They haven't arrived, but I am noticing that the distance between the jack and the cavity with the pots and battery is farther than the measurements EMG states that their cables are (I have a Jackson King V, so the jack is on the opposite side of the guitar). Do you typically add an extension in this case? Thanks again!