As one Dad to another, I switched to iNAV after watching Pawel, put his RUclips presentation on hold, while he calmly and patiently talked to his child that had interrupted him. My father always said know your vendor, and this was an indication to me that there are good people behind iNAV. I installed it on a quad and a fixed wing and I’m amazed at how simple the transition from Betaflight was. Thank you for everything!
@@FPVUniversityhi spy so im very confused with the magnetometer orintation. My module has no direction signs. So i will just install it exactly as seen in inav. Or does the red arrow have to be pointing forward at all times. For example do I set it up in inav axactly likr it is in real life. Or do i set it up with the arrow pointing forward at all time in inav the littpe red arrow
I have a question, is there a mode that you can implement where if the drone moves, it will stay in the position you moved it to? Like a constant position hold? Similar to that of a high end dji drone?
Hi! I would like to know more about position hold. Can he serve like a panic button ? Does he recover from any angle ? Does he stop fast enought even with high velocity ? Like during a sbang ?
I have to say this as well that the BN-880 is the best bang for your buck. It's cheap, always reliable and always had same or better reception as with other modules even indoors so it is sitting on almost (5 of 7) all my INAV models.
So you have to combine position hold with altitude hold, ie position hold only fixes lat and long, not altitude? The disarm works automatically, mentioned at 6:20? Thanks for the info, useful video.
Suggestion for tutorial on tuning for smooth quad waypoints. Now inav is very nice with waypoints in fixed wing but with quads it’s like a drunk sailor between points unless you go very slow.
I've always flown 5" with betaflight but I've recently got into 7" medium range cruising. Would you recommend inav over betaflight if I will be doing more smooth flying with very slight flips and rolls? I've used inav on wings before and it was brilliant but never used it on a drone before
I have a Ysido F4 v3 with baro Flight Controller and unfortunately, don't have SCL and SDA ports. Do you have something in mind how to connect a I2C equipement in the board? I have tried remapping ports in betaflight but doesn't seems to work.
I got BN-880 and speedybee F405 V3 stack. Magnetometer appeared only first time in Betaflight and never came online. I switched to iNav, but whatever you do Magentometer and Barometer are set in red, It has been so frustrating that I am thinking of giving up.
@@flat-eartheryes, I did. It seems there was some congestion in the signal, I removed the GPS with compass and also removed the transmitter antennas apart and all started detecting and working. I had to change their location.
Hi I have a real nightmare of a problem. I have never encountered this before. Just bought a Foxeer 120 GPS, I have wrapped the wires except the live wire in Copper tape and then insulated them so it cant make any connections on my Fc. I finds 6 maybe more sats in a minute. As soon as I attach the top plate of my quad, it stops all gps signals. I have tried copper tape on the underside of the top plate, stops signals Tried plastic plate as a test, stops signal The gps is located at the rear like yours and I cant put the cables on the outside at branches ect could easily catch them. I have done everything I can think of Help welcome
I have a question, I have tested position hold and alt hold, and in most cases, it worked fine but sometimes I had a situation when drone started to circle around position and these circles started to bigger and bigger and I needed to turn off position hold and turn on again after which it usually stabilizes. do you know a possible reason for this? could you please suggest steps how to fix it?
Ty Sir. Will this hold mode save fpv from crashing when done bad piloting ? Life when flying in acro and then switch to hold mode to recover controll and save fpv?
I installed RushFPV M10 GPS (no magnetometer) on my quad I already have a magnetometer on my quad. At a high altitude, I set ALT HOLD just moving left and right , little bit up and down trying to keeping the altitude. Don't know what happened as soon as I selected the position hold my quad drifted to one side at a high speed and slammed into trees and broken one frame arm. I got 15 satellite lock. :(
I’m used to Betaflight but tried INAV again... i don't get a compass reading or heading and I just had a flyaway when takeing off 🙄not cool ,did a Botgrinder off the neighbor's car ...at least i got it back....
strange now i got no rc link why ??I really wanted to try this out :{ tried to reflash again .........Went back to Betaflight and my reciever works again, bye bye Inav
Did it quiet a long time back but not worth doing as quad flew like a bag of spanners with inav, unless they have improved the flight characteristics now.
Hi Pawel build a 5 inch quad with inav Using hglrc f722 flight controller Hglrc gps First I put drone in angle mode after at a height of 1 meter put inav position hold mode and it's goes goes up in very fast speed of and after certain level it's get stable I want to stable my drone at the same height at angle mode Pls give suggestions
Wow thank you! I have been avoiding fpv drones because you "can't" let off the controller. avata seems to be only drone, but now when i heard of this im going to build my own! Let see how it goes :D
I see not many have made videos to explain on how to make the RTH more configurable. I am trying to figure out how to make the first trigger of going up very fast then return at a much greater speed. I will be flying in HUGE waves and want to be able to hit the RTH or get a failsafe and the drone shoots up in the air then returns home before battery dies. The way its now its way to slow :-D Im sure there are commands to get this done.. Thank you! @@FPVUniversity
I am using inav on cinebot30 but i am having issue . When i change board yaw orientation by 45 degree the magnetometer orientation also gets offset by 45 degree why ?
So i got it working really good in pos hold except for when i lower throttle just a little bit it falls down instead of slowly going down. Up is going good smooth and fast if i want. Tried alot but i am missing somthing in settings.any ideas what to look at? Thanks for still delivering good and fun videos Pavel
Hi Pawel I have switched to Inav. However I have no RTH or PosHold in the mode section. Could you please help? I have a GPS with compass and am using Inav 7
Can you please explain in detail where you wire the SCL and SDA to actually on the flight controller, which pads???. I assume there are extra pads on GPS module and are labelled hopefully in my case, no idea what brand etc. May try converting to INAV on one quad to see
Hello Pawel, I've heard it somewhere that you can 'parallel' GPS + Magnetometer + Barometer on a 'single' SDA/SCL? Having most FC's only come with a pair of them. I have GPS already connected on my FC's SDA/SCL but I plan to buy a separate Barometer and was stumped on where to put it.
You can connect all scl wires to scl and sda wires to sda. If needed you can splice wires from one sensor line( i.e gps) to all other i2c sensors ( mag, baro, airspeed, etc.)
I have Gyro,Accelerometer,Magnetometer,GPS,Flow,Sonar sensors detected but I cant find NAV POSHOLD mode option does it need a barometer? Btw nice Inav tutorials😀
It depends if Hobbywing will be interesed. So far, every manufacturer that was interested in that has a target. Drop a message to Hobbywing customer support so they know it's a wanted feature
Hi Pawel, I was following your steps and my gps is not communicating and is showing red in Inav. I’ve checked my wiring and it is correct and I’m running ublox protocol too! Any tips? Thanks
The situation is that all the FC manufacturers that were interested in having INAV support have INAV support. If not, I suggest contacting GepRC customer support
I am installing my Matek GPS at the rear of the drone on a 3D printed part. Should it be level, or at a slight angle (10-15 degrees) so it is close to level when flying? I've seen angled mounts like this on Thingiverse.
My first DIY position hold was with INav... but it flew terrible and toilet bowling was a REAL issue. I look forward to trying it again since the INav updates!
I was having trouble with it as well on a Darwin 129 I converted to INAV. Had to move the gps from it stock position in the back to on top. I think the cap on the esc was causing the toilet bowling issues.
Brilliant video, Pavel!!! Thank you so much, I had no idea that position hold was possible on fpv quads. Would you recommend it on a 7“ Longrange build?
Thanks for the video. It works great on my INAV builds. One suggestion maybe for another video: I have read that for FCs with no SDA SCL pads it may be possible to remap UART3 to I2C because this pin on the chip can both(?) Is this correct and how is it done?
This is really great information. I have a question, is the matek m8q 5883 just really good? so it doesn’t need to be mounted in a mast to avoid compass interference ? Will it get out of calibration often since it’s so close? I just have seen so many people use a mast to avoid compass interference issues. Struggled with it in the past myself.
Witaj Paweł w sumie ja też Paweł z Polski.Ostatnio zmieniłem oprogramowanie z BF na Inav bo jest bogatszy w opcje i zaciekawił mnie twój materiał o utrzymaniu pozycji drona.Ale mam problem ponieważ brakuje mi opcji nawigation mode nie wiem o co chodzi a mam wszystkie urządzenia potrzebne do tego.Czy mógłbyś mi coś doradzić.
GPS 20 satellites, magnetometer calibration in open field and still absolutely chaos. Drone flies great without nav modes. But nav modes goes crazy. :(
For some reason my drone shows height like -10 meters just after start. Probably, it's because a heavy noise which I can't defeat. I think my frame and motors are so old and bad so they should rest in peace, but It must fly :)
All quads... That have i2c pads, and an inav target. Kinda out of luck if you want to fly micros like 1s NanoLR Jhemcu GSF405A would be perfect but no interest from inav devs unless jhemcu comes to them first
I suppose you have not used INAV in a very long time. A lot changed in the last few years and I would even argue that setting up INAV can be simpler than setting up Betaflight when the same features are used here and here
lol there are so many I nav RTH fail videos. Commercial drones have surpassed the DIY Community. Need an example Amazon had hundreds of kits and parts a few years ago. Now you would be hard pressed to build 5 drones with unique internals on amazon. Guess if you like having a drone that's the same as the other guys drone you could save yourself hours, that translates to dollars and mistakes that also translates to dollars, by buying a commercial drone that fits your needs. If your need is a Drone that is equal or better than commercial drones you would need to start with goggles that are not "analog" and 4k capable video feed there goes 600 dollars or more (no drone parts included.) want to fly a mile away? Well there's another couple hundred dollars. still (no drone parts included.) now to run the video you might want a vista or an air unit. lol more commercial parts about 200 to 300 each still (no frame, flight controller, gps or motors.)
goggles digital hd fat shark $549 they suck vista digital $179 or air 03 $285 flight controller stack $129 we will use a cheep $30 frame middle of the road 60 dollar motors. batteries $60 antennas wires screws ect. $30 4k digital DIY average from scratch using the lowest figures above $1,037 (this drone will perform better only if you built it as an fpv drone. No DIY camera drone holds a match to commercial photography drones on the market at around $600 to $1000
I just noticed in that 1037 dollar build, you still don't have an rx or tx. you will need that if you don't already have one that links to all the stuff you just bought.
Don't get me wrong you can build one for 300 bux but you will be disappointed, when you see a kid with an $80 drone he grabbed off a shelf that is better.
As one Dad to another, I switched to iNAV after watching Pawel, put his RUclips presentation on hold, while he calmly and patiently talked to his child that had interrupted him. My father always said know your vendor, and this was an indication to me that there are good people behind iNAV. I installed it on a quad and a fixed wing and I’m amazed at how simple the transition from Betaflight was. Thank you for everything!
I like to refer to myslef as "Uncle Pawel" in such cases :)
I did a little bit of work on the magnetometer tool (not much) so it makes me very happy to see it being useful!
Nice work! And thanks for the effort
@@FPVUniversityhi spy so im very confused with the magnetometer orintation. My module has no direction signs. So i will just install it exactly as seen in inav. Or does the red arrow have to be pointing forward at all times.
For example do I set it up in inav axactly likr it is in real life. Or do i set it up with the arrow pointing forward at all time in inav the littpe red arrow
I tried so hard last year.
I will try again.
This is the one feature I want from the commercial world.
Thank you, thank you thank you! I'm on iNav 7.0 and I followed each step and it worked a treat. Stopped my toilet bowling and RTH worked beautifully.
Cool! Glad that you managed! Happy flying!
5:42 my drone does position hold before I take off perfect everytime. Never even had to enable or calibrate it....😁
I have a question, is there a mode that you can implement where if the drone moves, it will stay in the position you moved it to? Like a constant position hold? Similar to that of a high end dji drone?
Hi!
I would like to know more about position hold.
Can he serve like a panic button ?
Does he recover from any angle ?
Does he stop fast enought even with high velocity ?
Like during a sbang ?
I've got a bn-880 and it gets sat lock in seconds even indoors. I'm going to run inav on this build. Thanks for all your work demystifying FPV.
I have to say this as well that the BN-880 is the best bang for your buck. It's cheap, always reliable and always had same or better reception as with other modules even indoors so it is sitting on almost (5 of 7) all my INAV models.
So you have to combine position hold with altitude hold, ie position hold only fixes lat and long, not altitude? The disarm works automatically, mentioned at 6:20? Thanks for the info, useful video.
Even though I'm pretty comfortable with GPS setup on INAV, I ALWAYS get value from Pawel's videos!
Suggestion for tutorial on tuning for smooth quad waypoints. Now inav is very nice with waypoints in fixed wing but with quads it’s like a drunk sailor between points unless you go very slow.
Nice! Can it be treated as panic mode (similar to DJI panic button while freestyling)?
everyone tried this?
is HGLRC M80pro have magnetometer?
I've always flown 5" with betaflight but I've recently got into 7" medium range cruising. Would you recommend inav over betaflight if I will be doing more smooth flying with very slight flips and rolls? I've used inav on wings before and it was brilliant but never used it on a drone before
Excellent! Thanks a bunch for the tutorial, Pawel! 😃
Stay safe there with your family! 🖖😊
Thanks! 😃
I have a Ysido F4 v3 with baro Flight Controller and unfortunately, don't have SCL and SDA ports. Do you have something in mind how to connect a I2C equipement in the board? I have tried remapping ports in betaflight but doesn't seems to work.
I got BN-880 and speedybee F405 V3 stack. Magnetometer appeared only first time in Betaflight and never came online. I switched to iNav, but whatever you do Magentometer and Barometer are set in red, It has been so frustrating that I am thinking of giving up.
did you figure it out?
@@flat-eartheryes, I did. It seems there was some congestion in the signal, I removed the GPS with compass and also removed the transmitter antennas apart and all started detecting and working. I had to change their location.
Hello,
In Position hold mode or altitude hold mode can we rotate the quad with the yaw stick? or are stick inputs disabled?
Thank you.
In poshold, you still can use the control stick. Including yaw.
@@serang Thank you Sir!
Hi I have a real nightmare of a problem. I have never encountered this before.
Just bought a Foxeer 120 GPS, I have wrapped the wires except the live wire in Copper tape and then insulated them so it cant make any connections on my Fc.
I finds 6 maybe more sats in a minute.
As soon as I attach the top plate of my quad, it stops all gps signals.
I have tried copper tape on the underside of the top plate, stops signals
Tried plastic plate as a test, stops signal
The gps is located at the rear like yours and I cant put the cables on the outside at branches ect could easily catch them.
I have done everything I can think of
Help welcome
there is nothing you can do. Too much RF interference. So either buy better GPS or have it in the back where is less RF noise
Where do you get your Coax cable from? The cable that you use in your quad. Can you message me and let me know please?
I have a question, I have tested position hold and alt hold, and in most cases, it worked fine but sometimes I had a situation when drone started to circle around position and these circles started to bigger and bigger and I needed to turn off position hold and turn on again after which it usually stabilizes. do you know a possible reason for this? could you please suggest steps how to fix it?
My drone all motors rotate in anticlockwise, I am not able to set the motors in inav. Pls help me
When I turn on the arm switch the motors beep and make a noise . The motors cannot be started
Ty Sir.
Will this hold mode save fpv from crashing when done bad piloting ?
Life when flying in acro and then switch to hold mode to recover controll and save fpv?
Hello , thx for this great Video , I wanted to ask if I could get in Touch with you anyhow to ask some specific questions about inav ??
can i flash inav in mamba f405 mk2?
I installed RushFPV M10 GPS (no magnetometer) on my quad I already have a magnetometer on my quad. At a high altitude, I set ALT HOLD just moving left and right , little bit up and down trying to keeping the altitude. Don't know what happened as soon as I selected the position hold my quad drifted to one side at a high speed and slammed into trees and broken one frame arm. I got 15 satellite lock. :(
Hi, the GOKU GM10 MINI V3 GPS supported by iNav? It is twice as cheap as the Matek.
I’m used to Betaflight but tried INAV again... i don't get a compass reading or heading and I just had a flyaway when takeing off 🙄not cool ,did a Botgrinder off the neighbor's car ...at least i got it back....
strange now i got no rc link why ??I really wanted to try this out :{ tried to reflash again .........Went back to Betaflight and my reciever works again, bye bye Inav
Happy flying!
Happy flying!
How can I program how many satellites I want to launsch with
It's not about number of sats, but HDOP quality
Hi mate, a like your tutorial, which electronics do you use on your drone? Thanks..
in the modes tab does the position/alt hold require angle mode as well to work?
Did it quiet a long time back but not worth doing as quad flew like a bag of spanners with inav, unless they have improved the flight characteristics now.
a lot changed in the last few years
What will hapend if while flying a gps mode go in a building and loss all the satellite connections?
emergency landing would be executed
@FPVUniversity thanks
Brilliant! Look like a great time to switch TO INAV!
It is!
Hi Pawel
build a 5 inch quad with inav
Using hglrc f722 flight controller
Hglrc gps
First I put drone in angle mode after at a height of 1 meter put inav position hold mode and it's goes goes up in very fast speed of and after certain level it's get stable
I want to stable my drone at the same height at angle mode
Pls give suggestions
Have you able to fix this problem on your drone coz I'm having the same problem with the same specs as your drone? tnx
Wow thank you! I have been avoiding fpv drones because you "can't" let off the controller. avata seems to be only drone, but now when i heard of this im going to build my own! Let see how it goes :D
did you build it yet?
Thank you so much for the guide!! Got mine to hover in place!
Glad I could help!
I see not many have made videos to explain on how to make the RTH more configurable. I am trying to figure out how to make the first trigger of going up very fast then return at a much greater speed. I will be flying in HUGE waves and want to be able to hit the RTH or get a failsafe and the drone shoots up in the air then returns home before battery dies. The way its now its way to slow :-D Im sure there are commands to get this done.. Thank you! @@FPVUniversity
As Tina says... You're simply the best ! THX
I have 7 inch quad with inav 5.1 installed on fc nd in computer.. im a newbie can you help me tune or do you have any preset for it
I am using inav on cinebot30 but i am having issue . When i change board yaw orientation by 45 degree the magnetometer orientation also gets offset by 45 degree why ?
this is how it's designed. Use Mag setup too in INAV
Can you tell me if I can connect an Eachine F411 Flight Controller to a GPS module because I don’t see SDA and SCL connectors on the flight controller
because there in no SCL and SDA on every FC. you have to buy FC with Baro build on
I have this one: FOXEER REAPER F745 45A 2-6S AIO FC
So i got it working really good in pos hold except for when i lower throttle just a little bit it falls down instead of slowly going down. Up is going good smooth and fast if i want.
Tried alot but i am missing somthing in settings.any ideas what to look at?
Thanks for still delivering good and fun videos Pavel
I think you should try using option to use mid-stick for alt control. It can be set on advanced tuning page. Happy flying!
@@FPVUniversity if not using the mid stick hoover does i loose resolution on throttle? If so That might be the case.
Thanks again
Hi Pawel
I have switched to Inav. However I have no RTH or PosHold in the mode section. Could you please help?
I have a GPS with compass and am using Inav 7
Baro? Do you have it as well?
@@FPVUniversity Thanks for the swift response!! Ive managed to sort it and am preparing for a test flight tomorrow!!!!!
Can you please explain in detail where you wire the SCL and SDA to actually on the flight controller, which pads???. I assume there are extra pads on GPS module and are labelled hopefully in my case, no idea what brand etc. May try converting to INAV on one quad to see
GPS with MAG will have 6 pads. + GND, TX, RX SCL SDA. SCL SDA might be marked CL, DA, SC, SD. Depends on the module
@@FPVUniversity Understand that GPS module part, but where on FC pads? As in, I've never seen SCL and SDA pads on FC, or any pinout diagram
because there in no SCL and SDA on every FC. you have to buy FC with Baro build on
I have this one: FOXEER REAPER F745 45A 2-6S AIO FC
Hello Pawel, I've heard it somewhere that you can 'parallel' GPS + Magnetometer + Barometer on a 'single' SDA/SCL? Having most FC's only come with a pair of them. I have GPS already connected on my FC's SDA/SCL but I plan to buy a separate Barometer and was stumped on where to put it.
You can connect all scl wires to scl and sda wires to sda. If needed you can splice wires from one sensor line( i.e gps) to all other i2c sensors ( mag, baro, airspeed, etc.)
Is this still good for 2024 or is there something better? Thanks
as good as in 2023
I have Gyro,Accelerometer,Magnetometer,GPS,Flow,Sonar sensors detected but I cant find NAV POSHOLD mode option does it need a barometer? Btw nice Inav tutorials😀
Hi, will there be a target for Hobbywing boards in the future? I want this for a new build.
It depends if Hobbywing will be interesed. So far, every manufacturer that was interested in that has a target. Drop a message to Hobbywing customer support so they know it's a wanted feature
Any news on iNAV 6? Can’t wait for the bf compatibility mode so I can flash my 7 inch to iNav for a safer long range experience.
Next week you should get something :)
Very cool! are there any BNF or RTF drones for sale with INAV and these features installed?
Hi Pawel, the problem is how do I know whether my current fpv has a built-in barometer? Do you have a suggestion to give a quick check on that？
Check if Configurator of the software you use detects baro, That usually is the way to handle this
Where is the option for disarming on landing? Have been looking for that.
In INAV 5 only in CLI but on INAV 6 it will be enabled by default
@@FPVUniversity Great, thanks much!
Hi Pawel, I was following your steps and my gps is not communicating and is showing red in Inav. I’ve checked my wiring and it is correct and I’m running ublox protocol too! Any tips?
Thanks
did you figure it out?
When will betaflight up its game and use the damn gps module as it should be used.
Hi, is geprc span f722 bt hd v2 flight controller supported on latest inav ? I tried using iflight twing firmware but all sensor is red.
The situation is that all the FC manufacturers that were interested in having INAV support have INAV support. If not, I suggest contacting GepRC customer support
I am installing my Matek GPS at the rear of the drone on a 3D printed part. Should it be level, or at a slight angle (10-15 degrees) so it is close to level when flying? I've seen angled mounts like this on Thingiverse.
Level. It simplifies setup and when it's not level you have to precisely adjust magnetometer orientation as well
Pawel, great video. My drone holds position well, but does not hold altitude well...any suggestions? Thanks!
Vibration and/or wind gusts in barometer. Start with adding some open-cell foam over the barometer
Hey Pavie! Can I use missions made in INAV 4.x use in INAV 5.1?
I'd like to convert my Tyro129 to INAV. Will that FC be compatible?
That's the Matek F405 target? Might work
Can this be done with cinewhoop?
Of course
My first DIY position hold was with INav... but it flew terrible and toilet bowling was a REAL issue.
I look forward to trying it again since the INav updates!
Toilet bowling is almost always compass misaligment, very easy to fix.
I was having trouble with it as well on a Darwin 129 I converted to INAV. Had to move the gps from it stock position in the back to on top. I think the cap on the esc was causing the toilet bowling issues.
@@sams9716 Having the mag next to wiring with high currents can do that as well.
@@adilsongoliveira Maybe now - this was years ago....
Brilliant video, Pavel!!! Thank you so much, I had no idea that position hold was possible on fpv quads. Would you recommend it on a 7“ Longrange build?
Yes, absolutely
Thanks for the video. It works great on my INAV builds. One suggestion maybe for another video: I have read that for FCs with no SDA SCL pads it may be possible to remap UART3 to I2C because this pin on the chip can both(?) Is this correct and how is it done?
This is doable only for some FC. It's not a rule! Majority of INAv supported FC have I2C already
This is really great information. I have a question, is the matek m8q 5883 just really good? so it doesn’t need to be mounted in a mast to avoid compass interference ? Will it get out of calibration often since it’s so close?
I just have seen so many people use a mast to avoid compass interference issues. Struggled with it in the past myself.
All my quads fly with gps/mag between rear arms and it works perfectly
@@FPVUniversity Cool 😎
Super good Video👍
One more cavetta ☝️
The GPS icon will not turn into blue if you do not turn on your quad.
You have to connect the battery ☝️
Depends on flight controller. Many power GPS from USB too
@@FPVUniversity That was exactly the problem. The module lit up, but it wasn't until I connected the drone to the battery that the icon turned blue.
Witaj Paweł w sumie ja też Paweł z Polski.Ostatnio zmieniłem oprogramowanie z BF na Inav bo jest bogatszy w opcje i zaciekawił mnie twój materiał o utrzymaniu pozycji drona.Ale mam problem ponieważ brakuje mi opcji nawigation mode nie wiem o co chodzi a mam wszystkie urządzenia potrzebne do tego.Czy mógłbyś mi coś doradzić.
Nice. Make a smaller quad, for people that just start learning n understanding inav,position hold.
Can Inav hold position work with GPS without a barometer and compass?
no, these two are essential for altitude and heading, otherwise the only point of reference is the 2d GPS geo position.
Aaand #10 put good high uF low ESR cap and twisted wires.
Thanks again!
Any time!
hello from north queensland
More educational videos like this...... Please
Inav inav inav...... Like JB...
Lots of tutorials....
GPS 20 satellites, magnetometer calibration in open field and still absolutely chaos. Drone flies great without nav modes. But nav modes goes crazy. :(
For some reason my drone shows height like -10 meters just after start. Probably, it's because a heavy noise which I can't defeat. I think my frame and motors are so old and bad so they should rest in peace, but It must fly :)
I'm here just to hear you say, "install inav..."
well, you know.... had no other option really :)
the boss!
Kawetas❤
Wow
All quads... That have i2c pads, and an inav target. Kinda out of luck if you want to fly micros like 1s NanoLR
Jhemcu GSF405A would be perfect but no interest from inav devs unless jhemcu comes to them first
+1👍 💪
Pain and inav, inav and pain.
No, thanks Pavel.
I suppose you have not used INAV in a very long time. A lot changed in the last few years and I would even argue that setting up INAV can be simpler than setting up Betaflight when the same features are used here and here
lol there are so many I nav RTH fail videos. Commercial drones have surpassed the DIY Community. Need an example Amazon had hundreds of kits and parts a few years ago. Now you would be hard pressed to build 5 drones with unique internals on amazon. Guess if you like having a drone that's the same as the other guys drone you could save yourself hours, that translates to dollars and mistakes that also translates to dollars, by buying a commercial drone that fits your needs. If your need is a Drone that is equal or better than commercial drones you would need to start with goggles that are not "analog" and 4k capable video feed there goes 600 dollars or more (no drone parts included.) want to fly a mile away? Well there's another couple hundred dollars. still (no drone parts included.) now to run the video you might want a vista or an air unit. lol more commercial parts about 200 to 300 each still (no frame, flight controller, gps or motors.)
goggles digital hd fat shark $549 they suck
vista digital $179 or air 03 $285
flight controller stack $129
we will use a cheep $30 frame
middle of the road 60 dollar motors.
batteries $60
antennas wires screws ect. $30
4k digital DIY average from scratch using the lowest figures above $1,037 (this drone will perform better only if you built it as an fpv drone. No DIY camera drone holds a match to commercial photography drones on the market at around $600 to $1000
I just noticed in that 1037 dollar build, you still don't have an rx or tx. you will need that if you don't already have one that links to all the stuff you just bought.
Don't get me wrong you can build one for 300 bux but you will be disappointed, when you see a kid with an $80 drone he grabbed off a shelf that is better.
my ears bleed
that's just like my eyes when I read this comment