I like how they keyed the new part to self center itself. However I switched my MK 2 to the AirMarksMan backbone rail and I have to use a FX tensioner on it cause you don’t use the FX scope rail anymore.
So why replace the barrel harmonic tuner kit with this barrel tensioner? Is the tuner kit just get trashed? Is the tensioner system better? Seems like So much gadgets replaced only to shoot as good if not worse than the original factory setup. Can you do a group test comparison between all three setup (factory vs. harmonic tuner vs. barrel tensioner system)?
Nice video as usual and it would be much nicer if you did accuracy testing using pellets and slugs before and after to show the deference. All these improvements by deferent companies "including FX" came out for only one reason which is IMPROVING ACCURACY which means these guns are not quite accurate because of many issues related to the original design, FX and others trying to improve the Impact accuracy by selling these kits to the customer which means making FX customers paying more money to fix the design issues which should be fixed by FX from the beginning before selling the Impact to their customers. The FX Impact will cost you a lot more than the base price if you want an accurate air gun especially if you want to shoot slugs in this case you would have to pay for more stuff like back bone kit, power kit, barrel tensioning kit, power block, adjustable stock, modified pin probe, modified barrel brass inlet, larger air bottle and the list is continued on and on until you find your self paying about $5000 for an airgun producing under 150 ft lb of energy at it's best performance! FX customer,
Did you notice if the gun sounded louder after installing the system? Since the hollow shroud is being replaced by the solid carbon fiber tensioner sleeve. Thank you for all these excellent videos!
@@DaleAllen it does require to print a new back part with a opening of 20mm and then you need to slide the new back part on when installing the new Huma carbon tube , and put the Huma front part on . So at this point you have the Huma installed with the printed back part of the shroud on it , then you take your shroud slide it over and screw it into the back part 😉
@@Airbuks Got it! thank you, again. I really appreciate it! Could I buy chance buy that 3d printed piece from you, or perhaps I could buy the 3d printer file and have it made by a 3d printing service?
@@DaleAllen I am not sure if the file I have works on the Huma kit , I have made one for the FX 800mm and have to double check if the carbon tubes have the same diameter
If it starts and ends with an accuracy test, it's definitely better, so we can know how big the difference is, anw its a good video, thanks for sharing pal
Thx , and I know the accuracy test is not in there but there are some reasons for that aswel 😉 1. jamming also that in the same video will make it very long and time consuming to get it out there . 2. I am living in a suburban area with a lot of kids and need to drive to the range 3 . Once I am at the range I rather have fun shooting and don’t always want to fill 😉 I bring my content when and how it unfolds as this is still a hobby and not my job ( don’t get paid to make video 😉) But I will eventually get to the range to fill something with this kit but there won’t be a before and after 🤷♂️
I have a kit on my M3 5.5mm but also on my Mk2. 35 cal and that gun i have shot a lot before. And a few times now in the new setup. I have the emperor silencer on that .35 and that gun was a bad shooter no good groups at 50 meters tried speeds from 850 til 920 fps had very consistent speeds with the jsb 81 grains. And with the new huma system groups are a lot better. 5 shots are now touching each other before never. So iam very happy with it.
@@Airbuks Thank you. In my country, installing a silencer is prohibited, so it is difficult for me to import a barrel tensioner with a male thread. I thought about fixing the barrel with the clamp that comes with the scope mount, but your answer made it difficult.
Have you tested it with slugs yet? What are your results? Also what do you think is better a kit like this or a barrel band like the one Blackarts design sells?
Yes I did testing with it and I found it has just the same accuracy as with the FX tensioning barrel system . No obvious difference between them . About the black art barrel band I can’t advise as I never had one
This new barrel tensioning system from Huma appears to be very well made and well thought out. With shipping this setup will cost approximately $300. USD, so is the improvement in accuracy enough to justify its expense? You failed to show some before and after target groups shot at 50 & 100 yards...so just how much did this setup improve your accuracy?
Probably very little if any if your shooting lighter pellets or slugs with no additional stuff on the end of the barrel . With a 40 grain slug at supersonic speed it might if you keep adding things on the end of the barrel like a large silencer along with the adjustable harmonic damper . Barrel droop is not good . I have spend a lot of money on a lot of upgrades I probably didn’t need . I shoot an NSA 28.5 grain slug at 920-940 fps on my MK2 3rd generation and factory silencer . If I ever go supersonic with 40 grain slugs I’m going with the M3 slugger from Utah Airguns . What I did find interesting is Matt Dauber is using a moderator or muzzle break on his high power M3 . It has the report of a rimfire 22 . I can assure you he didn’t put it on there unless it improved his accuracy .
As you know making these videos take a lot of time specially if I try to combine it with my day job that pays the bills 😉 so adding everything in one video is complicated. I will try to make a range video aswel when I get to it , but when go out and shoot my main priority is having fun with my son and father in law 😉
You failed to notice he said he'd be going out to test it in future videos. 24:30 The barrel tensioning aspect of the kit is practically identical to the other barrel tensioning kits out there, except it's more robust. It'll improve accuracy at least as much as those kits do when shooting heavy slugs above 900 or so fps, especially if the liner o-rings are replaced with a carbon fiber sleeve as well.
@@hotchihuahua1546 yes , the older my son gets the more important it gets for me and being able to share the hobby with my son and father in law is pretty cool 👍
@@Airbuks yes but which is better. I cant install both. I tried. Not compatible. Im debating to have one or the other installed. I would have to order the kit and didnt want to waist anymore money on ghe kit. Thanks so much for input!!
@@nephtalilucero8084 you can’t compare them , they do both very different things . 🤷♂️ if you shoot pellets I would choose the tuner if you shoot slugs I would choose the Huma tensioning kit but if you do that know that you don’t have a shroud and makes your gun louder
You can get buy without, I have one so every time I get torque specs I do that . I don’t expect any difference in accuracy if you just do it by hand , just make sure you don’t over do it and strip the threads. The most important is that the block is screwed down with equal opening on each side
@@saviofalcao670 your quest is a little confusing the FX Maverick barrel fits the Impact but the shroud is to long the barrel tensioning kit from Huma doesn’t contain any barrel 🤷♂️ and is only made for the impact
The Huma air barrel Tensioner DOES NOT work on the Impact M3 without replacing the front barrel support. I ordered the exact same kit from Huma Air and the holes do not line up. Huma Air customer support told me I need to buy FX10339 part to make it work. How did you make this fit without replacing the front barrel support?
Not great if you want to switch out calibers, but at least it's available. Unlike the FX one at Utah which everyone has been telling us about for 2 years now and is still not available for us peasants.
Hi mate, ook van Osschot city las ik ergens. En minstens even begeesterd door FX als ik 😉 Graag eens afspreken om wat ideeën en tips uit te wisselen. Indien je interesse hebt hoor ik het graag. Greetz
Hoi mede kasseistamper 😉 , vooral begeesterd door luchtbuksen in het algemeen maar met een voorliefde voor FX 👍 we kunnen zeker eens afspreken, altijd blij schutters uit de buurt te ontmoeten. Stuur even een mail naar airbuks@icloud.com dan hoeven we hier niet alles neer te zetten 😉
Shame it doesn't work with the FX Harmonic Barrel Tunner 😞 Not sure I like the idea of tensioning the end nut to fine tune the harmonics, it's a bit hit and miss... if you'll excuse the pun!
No pun taken 😉 the barrel tensioning system by FX also has a similar tightening screw at the front , as I showed in the video with some modification you can use the barrel tuner or you need to use the stand alone tuner that screws on the 1/2 unf
Ok I understand, look just because you are taking your time to write back to me I'll consider to get one for my rifle, thank you body, for making our life easier
@@elcristiano22 i try to reply to every comment 👍 but don’t buy it because of me , the meaning for the video is to show people up and close how the product looks , if it’s something for them they have to decide I don’t get anything out of it 😉
@@elcristiano22 i try to reply to every comment 👍 but don’t buy it because of me , the meaning for the video is to show people up and close how the product looks , if it’s something for them they have to decide I don’t get anything out of it 😉 I just liked the product
I really enjoy all your videos, very informative and very professional, thanks again for all that you do for the air rifle community🤙🏽😊
Thx and your welcome 🙏
As always another top vid, thanks again 💯
Thx 🙏
I like how they keyed the new part to self center itself. However I switched my MK 2 to the AirMarksMan backbone rail and I have to use a FX tensioner on it cause you don’t use the FX scope rail anymore.
I would like to get myself a backbone rail aswel for one of my setups, they look awesome 👍
Excellent video.
Thx
So why replace the barrel harmonic tuner kit with this barrel tensioner? Is the tuner kit just get trashed? Is the tensioner system better? Seems like So much gadgets replaced only to shoot as good if not worse than the original factory setup. Can you do a group test comparison between all three setup (factory vs. harmonic tuner vs. barrel tensioner system)?
We are waiting for the video of the groups. We'll see if the next episode will be.🤞
Yes offcours, I just got access to a new range with 185m 😉👍
Great product video. Just ordered it :-).
Nice 👍
Nice video as usual, By the way after changing the o-ring my plenum is now holding air again
Glad you could fix the issue 👌 well done 👍
I can’t wait to see accuracy test.
Coming soon , can’t do everything at once 😉
@@Airbuks Until now I can't see it bro. haha
@@jennysok indeed have other stuff that I did in the meanwhile 🫣 and I rebuild the setup already to something else 😬
@@Airbuks I knew that bro. I always enjoy your new videos.
@@jennysok thx 😉
Nice video as usual and it would be much nicer if you did accuracy testing using pellets and slugs before and after to show the deference.
All these improvements by deferent companies "including FX" came out for only one reason which is IMPROVING ACCURACY which means these guns are not quite accurate because of many issues related to the original design, FX and others trying to improve the Impact accuracy by selling these kits to the customer which means making FX customers paying more money to fix the design issues which should be fixed by FX from the beginning before selling the Impact to their customers.
The FX Impact will cost you a lot more than the base price if you want an accurate air gun especially if you want to shoot slugs in this case you would have to pay for more stuff like back bone kit, power kit, barrel tensioning kit, power block, adjustable stock, modified pin probe, modified barrel brass inlet, larger air bottle and the list is continued on and on until you find your self paying about $5000 for an airgun producing under 150 ft lb of energy at it's best performance!
FX customer,
My carbon fiber sleeve was a little short and I didn’t know it so my transfer port brass broke now I’m back to where I started
Did you contact Huma about it ?
I’m sorry it was a FX barrel tension kit that I have the problem with
Did you notice if the gun sounded louder after installing the system? Since the hollow shroud is being replaced by the solid carbon fiber tensioner sleeve. Thank you for all these excellent videos!
Yes indeed , it sounds louder .
But with some small modifications it is possible to but the original shroud back over it 😉
@@Airbuks That's great news! Would you be willing to share those small modifications?
@@DaleAllen it does require to print a new back part with a opening of 20mm and then you need to slide the new back part on when installing the new Huma carbon tube , and put the Huma front part on .
So at this point you have the Huma installed with the printed back part of the shroud on it , then you take your shroud slide it over and screw it into the back part 😉
@@Airbuks Got it! thank you, again. I really appreciate it! Could I buy chance buy that 3d printed piece from you, or perhaps I could buy the 3d printer file and have it made by a 3d printing service?
@@DaleAllen I am not sure if the file I have works on the Huma kit , I have made one for the FX 800mm and have to double check if the carbon tubes have the same diameter
If it starts and ends with an accuracy test, it's definitely better, so we can know how big the difference is, anw its a good video, thanks for sharing pal
Thx , and I know the accuracy test is not in there but there are some reasons for that aswel 😉
1. jamming also that in the same video will make it very long and time consuming to get it out there .
2. I am living in a suburban area with a lot of kids and need to drive to the range
3 . Once I am at the range I rather have fun shooting and don’t always want to fill 😉
I bring my content when and how it unfolds as this is still a hobby and not my job ( don’t get paid to make video 😉)
But I will eventually get to the range to fill something with this kit but there won’t be a before and after 🤷♂️
I have a kit on my M3 5.5mm but also on my Mk2. 35 cal and that gun i have shot a lot before. And a few times now in the new setup. I have the emperor silencer on that .35 and that gun was a bad shooter no good groups at 50 meters tried speeds from 850 til 920 fps had very consistent speeds with the jsb 81 grains. And with the new huma system groups are a lot better. 5 shots are now touching each other before never. So iam very happy with it.
@@andrebosgraaf2086 nice 👍
Nice video! Hopefully they come out with one for the Maverick. They seem to be forgetting about that platform lately...
I will tell them 👍
Agree, if it's not an Impact, it doesn't exist 😥
Hi great video what are the dimensions of the
Carbon finer sleeve (over the barrel)
Thanx
I don’t know it by heart by I believe it has a OD of 20mm and since a FX barrel has a OD of 13.9-14 mm that should also be the ID of the shroud
Is huma fx tension barrel kit whether it comes with dual transfer port for .25 kit
Mantap bos smoga bisa punya 😘😘😘😘
Can the clamp that comes with the rail be used with a normal shroud?
Without modifications no , the original shroud has a smaller opening and doesn’t fit over the cf sleeve that is needed to creat the tension
@@Airbuks Thank you.
In my country, installing a silencer is prohibited, so it is difficult for me to import a barrel tensioner with a male thread.
I thought about fixing the barrel with the clamp that comes with the scope mount, but your answer made it difficult.
@@BlackJoker.22 you could cut the threads off 🤷♂️
Have you tested it with slugs yet? What are your results? Also what do you think is better a kit like this or a barrel band like the one Blackarts design sells?
Yes I did testing with it and I found it has just the same accuracy as with the FX tensioning barrel system . No obvious difference between them .
About the black art barrel band I can’t advise as I never had one
This new barrel tensioning system from Huma appears to be very well made and well thought out. With shipping this setup will cost approximately $300. USD, so is the improvement in accuracy enough to justify its expense? You failed to show some before and after target groups shot at 50 & 100 yards...so just how much did this setup improve your accuracy?
Probably very little if any if your shooting lighter pellets or slugs with no additional stuff on the end of the barrel . With a 40 grain slug at supersonic speed it might if you keep adding things on the end of the barrel like a large silencer along with the adjustable harmonic damper . Barrel droop is not good .
I have spend a lot of money on a lot of upgrades I probably didn’t need . I shoot an NSA 28.5 grain slug at 920-940 fps on my MK2 3rd generation and factory silencer . If I ever go supersonic with 40 grain slugs I’m going with the M3 slugger from Utah Airguns .
What I did find interesting is Matt Dauber is using a moderator or muzzle break on his high power M3 . It has the report of a rimfire 22 . I can assure you he didn’t put it on there unless it improved his accuracy .
As you know making these videos take a lot of time specially if I try to combine it with my day job that pays the bills 😉 so adding everything in one video is complicated. I will try to make a range video aswel when I get to it , but when go out and shoot my main priority is having fun with my son and father in law 😉
You failed to notice he said he'd be going out to test it in future videos. 24:30
The barrel tensioning aspect of the kit is practically identical to the other barrel tensioning kits out there, except it's more robust. It'll improve accuracy at least as much as those kits do when shooting heavy slugs above 900 or so fps, especially if the liner o-rings are replaced with a carbon fiber sleeve as well.
@@Airbuks having fun with your family is what it’s all about .
@@hotchihuahua1546 yes , the older my son gets the more important it gets for me and being able to share the hobby with my son and father in law is pretty cool 👍
Are Huma going to make these for the maverick ?
Not sure , maybe 🤔. You can send them a mail and ask
Will this work on a maverick by chance.
No at the moment it’s only for the impact, but Huma told me they are working on one for the Maverick aswel 😉
Is the harmonic tooner by fx better than this system?
This is a barrel tensioning system , not to be confused with a harmonic barrel tuner
@@Airbuks yes but which is better. I cant install both. I tried. Not compatible. Im debating to have one or the other installed. I would have to order the kit and didnt want to waist anymore money on ghe kit. Thanks so much for input!!
@@nephtalilucero8084 you can’t compare them , they do both very different things . 🤷♂️ if you shoot pellets I would choose the tuner if you shoot slugs I would choose the Huma tensioning kit but if you do that know that you don’t have a shroud and makes your gun louder
Que maravilha, quando irão lançar para FX CROWN
English 😬?
Hi, thanks for such as great video! Is that 600mm version?
Yes in the video it’s a 600mm setup
Is it important to use a torque screwdriver ? I can't find it on the web with this tightening torque...
You can get buy without, I have one so every time I get torque specs I do that .
I don’t expect any difference in accuracy if you just do it by hand , just make sure you don’t over do it and strip the threads.
The most important is that the block is screwed down with equal opening on each side
Hi. Does fx maverick barrel fit Impact m3?
Yes the barrel itself fits , but the shroud lengths are different
@@Airbuks so the shroud won't fit?
@@saviofalcao670 if you mean the complete Huma kit , this is only for the Impactqo
@@Airbuks yes full barrel kit
@@saviofalcao670 your quest is a little confusing the FX Maverick barrel fits the Impact but the shroud is to long the barrel tensioning kit from Huma doesn’t contain any barrel 🤷♂️ and is only made for the impact
The Huma air barrel Tensioner DOES NOT work on the Impact M3 without replacing the front barrel support. I ordered the exact same kit from Huma Air and the holes do not line up. Huma Air customer support told me I need to buy FX10339 part to make it work. How did you make this fit without replacing the front barrel support?
I see you addressed the issue. good info.
On my m3 it just worket i only had tot unscrew the bolts push the front barrel suport to the back and i could mounth it.
I have addressed it in the video aswel , they told me that all the kits from now on fit the M3 aswel
Hi. I received the Huma barrel tensioner last week. It will definitly fit the M3 support now.
@@markusscholl4958 thx for the information 👍
Show
Quanto custa uma Carabina dessa ?
English 😬?
@@Airbuks não falo English
Not great if you want to switch out calibers, but at least it's available. Unlike the FX one at Utah which everyone has been telling us about for 2 years now and is still not available for us peasants.
They should give you a shim kit to center it.
Some post it papers can do the trick aswel 😉
Hi mate, ook van Osschot city las ik ergens. En minstens even begeesterd door FX als ik 😉 Graag eens afspreken om wat ideeën en tips uit te wisselen. Indien je interesse hebt hoor ik het graag. Greetz
Hoi mede kasseistamper 😉 , vooral begeesterd door luchtbuksen in het algemeen maar met een voorliefde voor FX 👍 we kunnen zeker eens afspreken, altijd blij schutters uit de buurt te ontmoeten.
Stuur even een mail naar airbuks@icloud.com dan hoeven we hier niet alles neer te zetten 😉
Ein Testbericht vorher und nachher auf 50 /100 Meter wäre interessant.
This will come soon
Shame it doesn't work with the FX Harmonic Barrel Tunner 😞 Not sure I like the idea of tensioning the end nut to fine tune the harmonics, it's a bit hit and miss... if you'll excuse the pun!
No pun taken 😉 the barrel tensioning system by FX also has a similar tightening screw at the front , as I showed in the video with some modification you can use the barrel tuner or you need to use the stand alone tuner that screws on the 1/2 unf
nice video and well made , but i think there are many parts involved and a little tricky install ,sorry
Thx , it’s not that much once everything is installed the first time .
It might look like that as I try to cover as much detail as possible on video 😉
Ok I understand, look just because you are taking your time to write back to me I'll consider to get one for my rifle, thank you body, for making our life easier
@@elcristiano22 i try to reply to every comment 👍 but don’t buy it because of me , the meaning for the video is to show people up and close how the product looks , if it’s something for them they have to decide
I don’t get anything out of it 😉
@@elcristiano22 i try to reply to every comment 👍 but don’t buy it because of me , the meaning for the video is to show people up and close how the product looks , if it’s something for them they have to decide
I don’t get anything out of it 😉 I just liked the product
Thanks bro! You rocks!
Ok all good buddy but i would like to show us if this really works.... If it really make a deference...
Coming soon 😉👍
Tried . But really not working
Привіт з України,подарить один апарат инвалиду подпищику можно???.