Below are my affiliate links to the parts and tools you would use to complete this job. I may receive a small commission from the product sales. Thank you! Genuine Toyota coolant (3 gallons required): amzn.to/3Dy8UxQ Coolant bleeding funnel kit: amzn.to/3QbalKl Sturdy 4 Gallon coolant drain pan: amzn.to/3Ou4iiu 5/16" drain hose: amzn.to/43E0cJa Automotive trim and clip removal kit: amzn.to/3KgKGfg Truck jack stands: amzn.to/3q6VS7t 1/2" drive cordless impact wrench kit: amzn.to/3Kcw00I 3/8" drive flex head digital torque wrench: amzn.to/3O1EOru Rechargeable LED mini work light: amzn.to/3Y74OpY
Just replaced the radiator on my "03 V8 4Runner. I refill the rad slowly as you mentioned, make sure the overflow reservoir is at least half full, if not over full, and then install radiator cap, take it for a 5-10 mile drive, so thermostat opens, and then check and top off the overflow reservoir as required for the next 2 or 3 drives. After two drives this time, reservoir needed topping off. I only use Toyota recommended coolant.
@@RonRussell-sj1zf the 4.7L V8 takes a lot longer to bleed the air out of than the 5.7L for some reason. I think you did everything correctly, no issues.
Hey I overfilled my coolant to the very top on accident on my 2015 Toyota tundra. A fuel transfer pump isn’t doing the trick. I should be able to just drain it a bit so it lowers to “full” again right? And be good to go?
@@adambruneau8968 hi Adam, there is a list of sponsored Amazon links in the description below the video with all the parts needed to do the job. The rubber hose is pretty much always measured by the inner diameter amzn.to/43E0cJa Thanks!
@@phil1723 you can do it if you want to get the last little bit of coolant out. The video follows the repair manual and they don’t tell you to drain it.
Below are my affiliate links to the parts and tools you would use to complete this job. I may receive a small commission from the product sales. Thank you!
Genuine Toyota coolant (3 gallons required): amzn.to/3Dy8UxQ
Coolant bleeding funnel kit: amzn.to/3QbalKl
Sturdy 4 Gallon coolant drain pan: amzn.to/3Ou4iiu
5/16" drain hose: amzn.to/43E0cJa
Automotive trim and clip removal kit: amzn.to/3KgKGfg
Truck jack stands: amzn.to/3q6VS7t
1/2" drive cordless impact wrench kit: amzn.to/3Kcw00I
3/8" drive flex head digital torque wrench: amzn.to/3O1EOru
Rechargeable LED mini work light: amzn.to/3Y74OpY
Thanks. It's guys like you that make the internet a great place.
@@yodin9232 thank you for your kind words!
Appreciate the detailed video and tips 👍. I didn’t even realize there were drains on the side of the engine! Thanks again 👍
@@DJ-gh4dg any time!
best video on youtube on this topic. Thank you for being so concise
@@samsquatch9676 my pleasure, thank you for the feedback!
Perfectly explained and executed. Keep the tundra videos coming
@@M4ttj0nes thanks Matt, will do!
Just replaced the radiator on my "03 V8 4Runner. I refill the rad slowly as you mentioned, make sure the overflow reservoir is at least half full, if not over full, and then install radiator cap, take it for a 5-10 mile drive, so thermostat opens, and then check and top off the overflow reservoir as required for the next 2 or 3 drives. After two drives this time, reservoir needed topping off. I only use Toyota recommended coolant.
@@RonRussell-sj1zf the 4.7L V8 takes a lot longer to bleed the air out of than the 5.7L for some reason. I think you did everything correctly, no issues.
Thanks!
@@johnspitta6725 thank you so much for your support, I truly appreciate it!
Thanks my great friend for all best videos and haw about Toyota Camry XLE V6 2009 information 👏👏🙏
Will do if I ever get a chance, but I do not own one of those, so don't know when I would have the opportunity to work on one.
Supercharge nice
@@rc846 yep 😀
Hey I overfilled my coolant to the very top on accident on my 2015 Toyota tundra. A fuel transfer pump isn’t doing the trick. I should be able to just drain it a bit so it lowers to “full” again right? And be good to go?
@@sebastiancuevas7441 you could partially drain the overflow tank by disconnecting the hose that goes to the radiator cap.
Wouldn’t this be a good time to replace the thermostat?
@@cdelapaz5 they rarely ever fail, but you can definitely replace it at the same time if you want.
Got the TRD supercharger on it I see
Yep :)
Viktor, knowing your Tundra is also supercharged, do you have a similar procedure for flushing the cooling system of the supercharger?
Hi, I do not have a video for the supercharger system coolant replacement at this time, but will make one if I get a chance in the future.
Thank you for the video. Do you recommend draining the heater core as well?
@@pv4083 you can if you really want to, but there is a minimal amount of coolant inside of it.
@@Viktor_G_Automotive thank you. By the way the transmission fluid change on a 2021 Toyota sienna was really helpful. Thanks
@@pv4083 glad to hear!
Hello the 5/16 tubing
5/16" is the I.D. or O.D.
Thanks
@@rc846
5/16" ID drain hose: amzn.to/43E0cJa
he listed in the materials. it's 5/16" ID
Great Job Viktor. 👍 I Have That Funnel For Filling And I Also Like To Vacuum Fill The Cooling System.
Right on!
Where can we get the 5/16 diameter drain hose?
@@M4ttj0nes hi, all the parts links are in the description below the video, cheers!
5/16" drain hose: amzn.to/43E0cJa
@@Viktor_G_Automotive haha 😆 ty
@@M4ttj0nes no problem!
5/16 inner or outer diameter for the drain hose?
@@adambruneau8968 hi Adam, there is a list of sponsored Amazon links in the description below the video with all the parts needed to do the job. The rubber hose is pretty much always measured by the inner diameter amzn.to/43E0cJa
Thanks!
@@Viktor_G_Automotive awesome, thanks for the response. Great video!
@@adambruneau8968 my pleasure!
I didn't see you drain the Reservoir?
@@phil1723 you can do it if you want to get the last little bit of coolant out. The video follows the repair manual and they don’t tell you to drain it.