Very well explained for the layman, When the steel bar drops on his toes he will appreciate the use of steel capped boots. Thanks for sharing your knowledge
Nice to see the explanation on the drop center and showing the cut version of the Tyre for better understanding. When replacing my first Tyre it taken over an hour and i bent my bar a lot of swearing and sweating cuss I did not know where I was going wrong at first.
Best explanation ever.....I have been changing my tires forever, but I never did put atención to the drop center, that explain why it always took me forever to replace one freaking tire🤔
My first tire, many years ago. Served to use all the foul language I could get my hands on! The amount of sweat alone, would challenge any fashionable Hollywood training program! LOL 😂 I wish someone had teach me that "small" detail beforehand! Useless to say by the third tire I had a very good grasp of the concept of a wheel drop center! ;-)
I wrestled with this machine the first 2 tires then I actually started watching these vids! Now I can do a tire in about 10 minutes. Great explanation and I love the rubber pads, next on my list! You will scratch the heck out of an AL rim doing this in the machines stock form, your plastics and rubber are perfect. I will admit that I still use 1 tire iron even with this setup.
Excellent Video with top class commentary,,no fluff..great stuff..My way of breaking a tyre from the rim was to put the tyre under the rear wheel of my pickup truck and reverse over it.That was in Canada .But here in the UK tyres are so cheap its not worth the effort.
I have a HFT manual tire changer. I enjoy DIY automotive maintenance. After seeing a plethora of RUclips videos about modifications to it, and after many frustrating attempts at using the damned thing, I decided to just scrap the damned thing and use some hand tools that get the job done much easier on just a flat surface or desktop (or even theoretically changing a tire without removing the rim from the axle): 1. AME 71600 "Little Buddy" manual bead breaker. 2. Tire Bead Clamp Drop Center Tool (total of four clamps works best) 3. Tire levers (from HFT, total of 3 levers works best) 4. "BeadBuster" Tire Mounting paste (works better than liquid stuff or dish soap) 5. Thin plastic rollable kitchen Cutting Board (cut to 2-inch strips to protect rim from tire levers) 6. 5-gallon Air Tire Bead Seater Blaster Tool. The key to ease and success is to take advantage of the "drop center" area of a rim. The bead clamps ensure this gets done by pressing the bead down into the drop center area. Then the job is easily done by prying the bead one lever at a time, one inch at a time, until it seats completely. The air blaster tool works perfectly for thick ply truck or Special Trailer tires that are too stiff to simultaneously grab both sides of the rim surfaces, forcing the tire bead to contact the rim and seal up nicely. I save a lot of money from the investment of these tools and doing my own tire changes, because I have a fleet of 12 vehicles in my household and I enjoy online ordering from Amazon or TireRack for my tires. My next investment, after I get my next Stimulus Check, is an electronic tire balancer, just like at the pro tire shop, because the HFT manual balancer is not precise enough for the fastest cars in my fleet.
Well worth the investment. If you value your time waiting at a tire shop or dropping it off for service later that day. Many times I've encountered problems with the install or legal issues due to age of the tires. I'll happily do the work myself to avoid the conflict and wasted time.
I like your videos.. They are very clear and easy to understand. You have that kind of robotic sound to your voice and that fits these type of instructions well. Keep it up
Good video. Most folks don't know about the drop center. Also you know this, but there is only one correct side to remove the tire, as the drop center is typically not centered on the rim. At least in modern wheels it's not. I like that paste lube your using, as it leaves very little water vapor, which accelerates the corrosion of aluminum rims. That whole nitrogen thing is wasted if there is water vapor inside the tire. I've not seen that lube available in the states. I typically use a bar of soap, rub it on dry, and that works very well. But I do see micro bubbles and your sealant would be a good thing as it's not messy.
Thank you. Theres another video on yt of some "tire engineer" doing a change, that idiot works for kenda tires and doesn't even understand or explain the importance of the drop center. Your video crushes his.
I'm not too worried about scratching rims, but I did my own modifications. I welded some old bolts to the bead breaker to make it more sturdy, on tough beads it will bend and slip off. And the holes where the pins go through I welded some washers to make them stronger. Also the pipe that holds the bead breaker is slighty too long and needs grinded down. Works so much better now, If I get a new one, It'll be the first thing I do.
👌😍well done review & set up of a tire on a tire changer machine - it's highly technical with its important key elements regarding the subject - very appreciated 👍👍👍👍👍
I need to make that bar. Could you please give detail specs on the measurements and materials? I can see it, but getting it right is another matter. Thank you for a good video.
I saw another video where in the comments someone said the coloured dots, (yellow/red) printed on the tyres were meant to go at a certain position. Something to do with it being the heaviest part of the tyre, so you put it opposite the valve. Wish I could remember. Just meant you didn't need as much weight when balancing it.
Yes, but not all tires are marked this way. Somebody else left a comment, under my balancing tires video, that he turns the tire on the rim to find the right spot that will require fewer weights. Just two weeks ago I changed two tires and during balancing turned one 3 X 90 deg and another just once. Made a significant difference in the weights required to balance. Thanks for your comment!
@@rasyamotor1701 - Easy tip, listen to music AND sing it! Even on a very low volume (to yourself). You'll be acquainted with the words while training your vocals to another language. In a very relaxed and easy way! ;-)
That machine from Harbor Freight was the machine that used 40 years ago except the bead breaker was mounted to the wall in with hydraulic for those tires that don't like to come off
Great video with great explanation cheers where did you get your tyre bar from please it looked awsome and really easy to use compared to the standard bar you get with the tyre changer. Cheers
Tip: Remove the paint and polish the mount/dismount tips of the bar. Fine grades of sand paper and oil will do the trick just fine! ;-) Even this cheap Chinese tool will perform flawlessly with that done! Surely there's no need for plastic "bits and bobs".
The mounting device has a lot of friction with the rubber, which is why it offers a lot of resistance when riding it in the ring. El dispositivo de montar, tiene mucho roce con el caucho, por eso es que ofrece mucha resistencia al suncharlo en el ring.
I need to make that bar. Could you please give detail specs on the measurements and materials? I can see it, but getting it right is another matter. Thank you for a great video. I'm currently frustrated with the harbor freight bar over two days without luck already! I don't want to damage the new tire when mounting, and need to get something that can work well.
Why do people use lubricant to put a tire ON, but never use it to break the bead to get the tire off? I always lubricate around the tire bead if I'm trying to slide it past the bead. Otherwise, it just hangs up and make it more difficult to slip past. I've seen guys fight just to break a bead - on a completely dry tire! LOL! I'm like, "...whatever works for you, I guess."
Spray some kerosene before breaking the bead. Will make it so eazy you'd be scratching your head why you don't use kerosene for everything. Maybe for hydration too lol.
I've heard of this, "tire blowing up" thing. What exactly happens? I need to do this, but would like to try it by hand as I've seen in other videos. Don't wanting a tire blowing up though, where is the danger? Good video.
If the rubber is not damaged, cut or torn, and if you put the right size tire on the right size rim, then everything should be OK. Do not over inflate the tire.
The best way to prevent damage to the tires is to use proper technics! In all honesty there's no work around from it! Do it right and the probabilities of a miss happening, like blowing a tire basically vanish. The always and the never tips: - ALWAYS inspect a tire before assembly, even a new one! If lacking knowledge at least apply liberal amounts of very rare common sense! LOL 😂 - ALWAYS lube the tire, rim and eventually the tool tip! More on this in a second. - NEVER overinflate a tire! If you feel the need to do it. To seat a bead, etc. Please understand you're doing it WRONG. So step back and start it over again. ;-) About lube, the subject was not properly covered. On this otherwise very good video. But keep in mind ALL tires should be lubed in three (3) areas! Remember this number. They are respectively, both outer beads. AND the upper inner bead facing down (facing the rim)! This last one is probably the most underrated detail... Now let's talk about lube the RIM. Also three (3) areas! Upper outer lip AND both bead seats. With this properly done, pretty much all tires will be really easy to do. BTW it's worth mention, that it's much faster to do it, than write these details! Becomes a second nature. This week alone I set a few tires on steel rims and alloy rims. Some, even on the steel rims, seat the beads with as low pressure as 10~12 psi! The type of lube also play a roll. These very low pressures were accomplished with "hair spray" used as lube! Yes, normal (cheap) hair spray the ladies use to fix the hair. Exactly the same tires and rims set. assembled with soap, saw the pressure increase to around 25~30 psi. Both using the same lube technic as described above. Cheers
Tire fitting paste: shop.wurth.ca/vehicle-repair-components/wheel-tire/tire-mounting-repair-tools/tire-mounting-repair-chemicals/tire-fitting-paste/TIRE-FITTING-PASTE-11LBS-(5-KG)/890.1221/?gclid=Cj0KCQjwub-HBhCyARIsAPctr7z6hjJydLkCRskPIk8ipJUjWPT_rJxbfEkNenszEDNXsmZpHz_n5OIaAh1aEALw_wcB Tire valve multi tool: www.princessauto.com/en/tire-valve-repair-tool-with-valve-cores/product/PA0008253684 this one is more popular and you can use it to mount the valve on the rim. Good luck!
Tire fitting paste by Wurth: shop.wurth.ca/vehicle-repair-components/wheel-tire/tire-mounting-repair-tools/tire-mounting-repair-chemicals/tire-fitting-paste/TIRE-FITTING-PASTE-11LBS-(5-KG)/890.1221/ It is not sold in retail. Contact Wurth representative, he/she will visit you and take your order.
You should have been considering that there was a expensive sensor inside before you dismounted it or that you will check for the belt over lap and install it opposite of the valve stem to help aid in the balancing process and save shop on weights.
If you don't want to scratch the edge of the rim's outside, isn't it possible to turn the rim with the outside pointing downwards? Then you'll work on the backside and any scratches will notice.
The tire changer was purchased in Canada. Princess Auto, Harbor Freight, Northern Tools, and many more sell the very same changer, different color. I will do a separate video about the bar, but really there is nothing to it. What you can't see on the video is that the plastic prongs are reinforced by steel inserts.
@@robertdeptula2003 Yes, I'm also in Canada and have seen the tire changer at Princess Auto. I really like your bar, very similar to the no mar bar in design (which is very expensive to import with shipping and taxes from the US). I need to make a bar as I have an old tire changer but need the demount / mount bar. If possible, could you dm me some pictures of your bar? If not, I look forward to the video and thanks for the reply.
It's kind of ironic / funny that all the countries that use the metric system and try to ridicule the US for sticking with the Imperial (actually "US Customary Units") system still have their wheel diameters measured in inches... :) I like the looks of those plastic ends on the tire changer lever though... I might have to try to make myself some of them...
It's kind of ironic / funny that at the Metre Convention in Paris, France on May 20th AD 1875 the US of A signed the Treaty of the Metre along with other countries. This means that the US of A recognizes the metric system as the standard of measurements and all its pounds, gallons, inches, etc. are metric-based and multiplied by conversion factors. Samples of the original units are held in the National Institute of Standards and Technology www.nist.gov/ This means, that the imperial system used in the US of A is based on the metric system (SI). Did you know this? www.nist.gov/system/files/documents/2017/05/09/frn-59-5442-1959.pdf
@@robertdeptula2003 -- I'm an engineer (retired)... I am well aware that there are exact conversion factors between the US and metric systems and that it is possible to derive many through the memorization of of a few base constants... For example, if you want to convert from liters to gallon EXACTLY, you just need to remember that there are 231 cu-in in a gallon, 1000 ml in a liter, and 1 cu-cm = 1 ml -- it gives you 3.785411784 liters per gallon EXACTLY. That's the US gallon, not the Imperial gallon... My impression from spending some time in the UK though was that they use a mix of metric and Imperial for various things. For example, road distances will be measured in miles and distances to a near highway exit in yard, but bridge clearances in meters... Most weights are quoted in kg, but people tend to quote their weight in stones and pounds... There is nothing magical about the metric system like uninformed proponents that you have you believe... It's just another arbitrary system of measurements, albeit with unit conversions based on powers of 10...
It's a fashion faux pas of the greatest magnitude to wear socks with open footwear. The real danger is not an injury to his foot, but to his reputation at prep school.
Few years ago I bought it on line as a replacement part for different tire changer. Don't remember the name of the company. Can be easily done. A chunk of plastic can be bought at local supplier, same as the white plastic I bought for the changing bar.
This mount/demount bar is a simple build. All details are in the video, no hidden mechanisms or electronics. The only detail that you may not see is that plastics have metal inserts to keep it rigid. Good luck!
I cannot fathom why there are ANY downvotes here. You have explained this with precision.
It is for steeltoe sandals.
Very well explained for the layman, When the steel bar drops on his toes he will appreciate the use of steel capped boots. Thanks for sharing your knowledge
Nice to see the explanation on the drop center and showing the cut version of the Tyre for better understanding.
When replacing my first Tyre it taken over an hour and i bent my bar a lot of swearing and sweating cuss I did not know where I was going wrong at first.
Me too, thought I was stuck 🥵 struggled a while but got it on,will be better with this knowledge!!!
Sir you gave me the best tutorials about tires. Im amazed. Thank you 😊 blessings and more blessings to you and your family in Yahusha's name amen
Thank you
This is an amazing video. I wished the tire centers had these modifications and took that much care on changing tires.
Best explanation ever.....I have been changing my tires forever, but I never did put atención to the drop center, that explain why it always took me forever to replace one freaking tire🤔
InstaBlaster.
My first tire, many years ago. Served to use all the foul language I could get my hands on! The amount of sweat alone, would challenge any fashionable Hollywood training program! LOL 😂 I wish someone had teach me that "small" detail beforehand!
Useless to say by the third tire I had a very good grasp of the concept of a wheel drop center! ;-)
I wrestled with this machine the first 2 tires then I actually started watching these vids! Now I can do a tire in about 10 minutes. Great explanation and I love the rubber pads, next on my list! You will scratch the heck out of an AL rim doing this in the machines stock form, your plastics and rubber are perfect. I will admit that I still use 1 tire iron even with this setup.
I'm glad it helped.
Excellent Video with top class commentary,,no fluff..great stuff..My way of breaking a tyre from the rim was to put the tyre under the rear wheel of my pickup truck and reverse over it.That was in Canada .But here in the UK tyres are so cheap its not worth the effort.
Hy
I have a HFT manual tire changer. I enjoy DIY automotive maintenance. After seeing a plethora of RUclips videos about modifications to it, and after many frustrating attempts at using the damned thing, I decided to just scrap the damned thing and use some hand tools that get the job done much easier on just a flat surface or desktop (or even theoretically changing a tire without removing the rim from the axle):
1. AME 71600 "Little Buddy" manual bead breaker.
2. Tire Bead Clamp Drop Center Tool (total of four clamps works best)
3. Tire levers (from HFT, total of 3 levers works best)
4. "BeadBuster" Tire Mounting paste (works better than liquid stuff or dish soap)
5. Thin plastic rollable kitchen Cutting Board (cut to 2-inch strips to protect rim from tire levers)
6. 5-gallon Air Tire Bead Seater Blaster Tool.
The key to ease and success is to take advantage of the "drop center" area of a rim. The bead clamps ensure this gets done by pressing the bead down into the drop center area. Then the job is easily done by prying the bead one lever at a time, one inch at a time, until it seats completely. The air blaster tool works perfectly for thick ply truck or Special Trailer tires that are too stiff to simultaneously grab both sides of the rim surfaces, forcing the tire bead to contact the rim and seal up nicely.
I save a lot of money from the investment of these tools and doing my own tire changes, because I have a fleet of 12 vehicles in my household and I enjoy online ordering from Amazon or TireRack for my tires.
My next investment, after I get my next Stimulus Check, is an electronic tire balancer, just like at the pro tire shop, because the HFT manual balancer is not precise enough for the fastest cars in my fleet.
Well worth the investment. If you value your time waiting at a tire shop or dropping it off for service later that day. Many times I've encountered problems with the install or legal issues due to age of the tires. I'll happily do the work myself to avoid the conflict and wasted time.
I like your videos.. They are very clear and easy to understand. You have that kind of robotic sound to your voice and that fits these type of instructions well. Keep it up
Yes! It is me: ruclips.net/video/uc6f_2nPSX8/видео.html
Excellent! Most informative video on tires I’ve ever seen.
Thanks!
Good video. Most folks don't know about the drop center. Also you know this, but there is only one correct side to remove the tire, as the drop center is typically not centered on the rim. At least in modern wheels it's not.
I like that paste lube your using, as it leaves very little water vapor, which accelerates the corrosion of aluminum rims. That whole nitrogen thing is wasted if there is water vapor inside the tire.
I've not seen that lube available in the states. I typically use a bar of soap, rub it on dry, and that works very well. But I do see micro bubbles and your sealant would be a good thing as it's not messy.
The paste in US: www.wurthusa.com/Chemical-Product/Tire-Repair/Tire-Mounting-Paste-11-Lb-Pail/p/08901221
Ka price
Thank you. Theres another video on yt of some "tire engineer" doing a change, that idiot works for kenda tires and doesn't even understand or explain the importance of the drop center. Your video crushes his.
이렇게 까지 자세하게 설명 하는 동영상은 처음 타이어 단면 까지 준비한 동영상 대단합니다
도움이 되었습니다 감사합니다.
물론이죠
I'm not too worried about scratching rims, but I did my own modifications. I welded some old bolts to the bead breaker to make it more sturdy, on tough beads it will bend and slip off. And the holes where the pins go through I welded some washers to make them stronger. Also the pipe that holds the bead breaker is slighty too long and needs grinded down. Works so much better now, If I get a new one, It'll be the first thing I do.
👌😍well done review & set up of a tire on a tire changer machine - it's highly technical with its important key elements regarding the subject - very appreciated 👍👍👍👍👍
Excellent instructional video. Very thorough and clearly explained.
If that bar had a flat spot it wouldn't roll on you like that, probably wouldn't need that assist handle. Nice video!
Thanks.
I need to make that bar. Could you please give detail specs on the measurements and materials? I can see it, but getting it right is another matter. Thank you for a good video.
Outstanding explanation. Love the custom tool mods to save the rim.
Thank you
Great video thanks for sharing your thoughts and great videos
I saw another video where in the comments someone said the coloured dots, (yellow/red) printed on the tyres were meant to go at a certain position.
Something to do with it being the heaviest part of the tyre, so you put it opposite the valve. Wish I could remember. Just meant you didn't need as much weight when balancing it.
Yes, but not all tires are marked this way. Somebody else left a comment, under my balancing tires video, that he turns the tire on the rim to find the right spot that will require fewer weights. Just two weeks ago I changed two tires and during balancing turned one 3 X 90 deg and another just once. Made a significant difference in the weights required to balance. Thanks for your comment!
Your English is very easy to understand
It is because I "polished" my English!
English is my second language, I am Polish.
great ,, I have studied English for years but until now I have not been able to compile the right vocabulary. I can only hear it
@@rasyamotor1701 - Easy tip, listen to music AND sing it! Even on a very low volume (to yourself). You'll be acquainted with the words while training your vocals to another language. In a very relaxed and easy way! ;-)
Every wheel has two rims, most people won't understand this.
Я только в этом видео понял👍
Thank you for explaining the drop center in the middle. I have not noticed it.
You are welcome
That machine from Harbor Freight was the machine that used 40 years ago except the bead breaker was mounted to the wall in with hydraulic for those tires that don't like to come off
Love it. What materials were used for the ends of bar for removing and installing tire?
It is PETE, I have found it at a local plastic supply company.
Great video with great explanation cheers where did you get your tyre bar from please it looked awsome and really easy to use compared to the standard bar you get with the tyre changer.
Cheers
I made this bar. When you pause video you can see details. The contact parts are made of plastic reinforced inside with metal spikes.
Well spoken and Explained. Best one on here
Thank you
Yes brilliant, what did you use for the plastic pry part I can't think of anything I could carve it out of. Thanks
It is PETE, I have found it at a local plastic company selling different diameters.
Tip: Remove the paint and polish the mount/dismount tips of the bar. Fine grades of sand paper and oil will do the trick just fine! ;-)
Even this cheap Chinese tool will perform flawlessly with that done! Surely there's no need for plastic "bits and bobs".
The mounting device has a lot of friction with the rubber, which is why it offers a lot of resistance when riding it in the ring. El dispositivo de montar, tiene mucho roce con el caucho, por eso es que ofrece mucha resistencia al suncharlo en el ring.
I need to make that bar. Could you please give detail specs on the measurements and materials? I can see it, but getting it right is another matter. Thank you for a great video. I'm currently frustrated with the harbor freight bar over two days without luck already! I don't want to damage the new tire when mounting, and need to get something that can work well.
On my chanel in "about" section you have my email. Talk to me.
@@robertdeptula2003 Can you help me
Well done; excellent work.
Why do people use lubricant to put a tire ON, but never use it to break the bead to get the tire off? I always lubricate around the tire bead if I'm trying to slide it past the bead. Otherwise, it just hangs up and make it more difficult to slip past. I've seen guys fight just to break a bead - on a completely dry tire! LOL! I'm like, "...whatever works for you, I guess."
Thank you for sharing.
Spray some kerosene before breaking the bead.
Will make it so eazy you'd be scratching your head why you don't use kerosene for everything.
Maybe for hydration too lol.
4:41 i love the shop shoes! 😜
Steel toe.
Great video. Where can we buy the centering adapter piece? Thanks
Thank you. You can buy it at the plumbing section of any home improvement store.
Thank you Rob. Very informative!
You are welcome
Very well done Video and explanation, I just Subscribed So thank you for taking the time to make the video, Cheers from Garry From Australia
Thank you. Regards.
Okay where's video of making homemade take off bar
Look like ba no mar
Where did you get the modified bead breaker? Did you make it yourself?
I've heard of this, "tire blowing up" thing. What exactly happens? I need to do this, but would like to try it by hand as I've seen in other videos. Don't wanting a tire blowing up though, where is the danger? Good video.
If the rubber is not damaged, cut or torn, and if you put the right size tire on the right size rim, then everything should be OK. Do not over inflate the tire.
@@robertdeptula2003 ok, thanks!
@@szargos You are welcome
The best way to prevent damage to the tires is to use proper technics! In all honesty there's no work around from it!
Do it right and the probabilities of a miss happening, like blowing a tire basically vanish. The always and the never tips:
- ALWAYS inspect a tire before assembly, even a new one! If lacking knowledge at least apply liberal amounts of very rare common sense! LOL 😂
- ALWAYS lube the tire, rim and eventually the tool tip! More on this in a second.
- NEVER overinflate a tire! If you feel the need to do it. To seat a bead, etc. Please understand you're doing it WRONG. So step back and start it over again. ;-)
About lube, the subject was not properly covered. On this otherwise very good video. But keep in mind ALL tires should be lubed in three (3) areas! Remember this number. They are respectively, both outer beads. AND the upper inner bead facing down (facing the rim)! This last one is probably the most underrated detail...
Now let's talk about lube the RIM. Also three (3) areas! Upper outer lip AND both bead seats.
With this properly done, pretty much all tires will be really easy to do. BTW it's worth mention, that it's much faster to do it, than write these details! Becomes a second nature.
This week alone I set a few tires on steel rims and alloy rims. Some, even on the steel rims, seat the beads with as low pressure as 10~12 psi! The type of lube also play a roll. These very low pressures were accomplished with "hair spray" used as lube! Yes, normal (cheap) hair spray the ladies use to fix the hair.
Exactly the same tires and rims set. assembled with soap, saw the pressure increase to around 25~30 psi. Both using the same lube technic as described above.
Cheers
Real professional, thank you👍.
You are welcome
I did all that, but I also installed Wi-Fi on my tire changer!
😜
👍🏻
Sweet!
Why no mention of the red or yellow dots some tyres have?
There is a video on my channel that covers this subject.
Hi. Great video. Love the mods. Did you make the bead breaker or buy it like that?
I bought it several years ago. It was a replacement part for other hand operated tire changer. Don't remember the name of the company.
Ah!...the good old heavy duty work gloves and safety steel capped open toed sandal.
so where are you getting that red bead breaker from?
Great video...just need balance the tire
Here it is: ruclips.net/video/dAM6lrBOHOQ/видео.html
Fantastic video sir!
Thank you, sir.
Great video. Can you give the name of the valve tool and paste?
Tire fitting paste: shop.wurth.ca/vehicle-repair-components/wheel-tire/tire-mounting-repair-tools/tire-mounting-repair-chemicals/tire-fitting-paste/TIRE-FITTING-PASTE-11LBS-(5-KG)/890.1221/?gclid=Cj0KCQjwub-HBhCyARIsAPctr7z6hjJydLkCRskPIk8ipJUjWPT_rJxbfEkNenszEDNXsmZpHz_n5OIaAh1aEALw_wcB
Tire valve multi tool: www.princessauto.com/en/tire-valve-repair-tool-with-valve-cores/product/PA0008253684 this one is more popular and you can use it to mount the valve on the rim.
Good luck!
Hi..Great video what is the paste you use on the stem and bead?
Tire fitting paste by Wurth: shop.wurth.ca/vehicle-repair-components/wheel-tire/tire-mounting-repair-tools/tire-mounting-repair-chemicals/tire-fitting-paste/TIRE-FITTING-PASTE-11LBS-(5-KG)/890.1221/
It is not sold in retail. Contact Wurth representative, he/she will visit you and take your order.
You should have been considering that there was a expensive sensor inside before you dismounted it or that you will check for the belt over lap and install it opposite of the valve stem to help aid in the balancing process and save shop on weights.
How do you tell where the overlap is?
Robert ,How did you make the plastic inserts ? Do you have a video ?
I bought locally roll of HDPE plastic. It is easy to work on. Nothing fancy, pause the video for details.
If you don't want to scratch the edge of the rim's outside, isn't it possible to turn the rim with the outside pointing downwards?
Then you'll work on the backside and any scratches will notice.
Well done demonstration video. Thanks.
Thanks
Great video thanks so much.
Great job, I like it Thankyou!
Thanks
Great job.
Thanks!
Good Explanation
needed to add a bit of soapy water before breaking that bead.
How can I get some pictures of the tire mounting/de-mounting tool that you made? Did you make a video of how you made it?
On my chanel main page there is email. Send me message.
Would you be able to send me the pics for the bar and where did you get the protective pieces for the breaker?
On my chanel main page there is email. Send me message.
Uma beleza de canal
Obrigada
Well done!!
Thanks!
Well done 👍
Great video! What company is the tire changer stand from? Can you do a video on how you made the tire mount/demount bar?
The tire changer was purchased in Canada. Princess Auto, Harbor Freight, Northern Tools, and many more sell the very same changer, different color.
I will do a separate video about the bar, but really there is nothing to it. What you can't see on the video is that the plastic prongs are reinforced by steel inserts.
@@robertdeptula2003 Yes, I'm also in Canada and have seen the tire changer at Princess Auto. I really like your bar, very similar to the no mar bar in design (which is very expensive to import with shipping and taxes from the US). I need to make a bar as I have an old tire changer but need the demount / mount bar. If possible, could you dm me some pictures of your bar? If not, I look forward to the video and thanks for the reply.
@@richthevegan8611 Check your e-mail. I sent some pictures.
@@robertdeptula2003 Thank you so much. Very kind of you. Great work with the welding 👍
Hey Rob, where did you get the bead breaker modded piece?
Bought on liquidation sale.
It's kind of ironic / funny that all the countries that use the metric system and try to ridicule the US for sticking with the Imperial (actually "US Customary Units") system still have their wheel diameters measured in inches... :)
I like the looks of those plastic ends on the tire changer lever though... I might have to try to make myself some of them...
It's kind of ironic / funny that at the Metre Convention in Paris, France on May 20th AD 1875 the US of A signed the Treaty of the Metre along with other countries. This means that the US of A recognizes the metric system as the standard of measurements and all its pounds, gallons, inches, etc. are metric-based and multiplied by conversion factors. Samples of the original units are held in the National Institute of Standards and Technology www.nist.gov/
This means, that the imperial system used in the US of A is based on the metric system (SI). Did you know this? www.nist.gov/system/files/documents/2017/05/09/frn-59-5442-1959.pdf
@@robertdeptula2003 -- I'm an engineer (retired)... I am well aware that there are exact conversion factors between the US and metric systems and that it is possible to derive many through the memorization of of a few base constants... For example, if you want to convert from liters to gallon EXACTLY, you just need to remember that there are 231 cu-in in a gallon, 1000 ml in a liter, and 1 cu-cm = 1 ml -- it gives you 3.785411784 liters per gallon EXACTLY. That's the US gallon, not the Imperial gallon... My impression from spending some time in the UK though was that they use a mix of metric and Imperial for various things. For example, road distances will be measured in miles and distances to a near highway exit in yard, but bridge clearances in meters... Most weights are quoted in kg, but people tend to quote their weight in stones and pounds... There is nothing magical about the metric system like uninformed proponents that you have you believe... It's just another arbitrary system of measurements, albeit with unit conversions based on powers of 10...
Hi... First, thank you so much
Second, where can i find that rubber pieces... Thanks
Those are pieces cut out of a rubber mat you can buy in any home improvement store.
@@robertdeptula2003 thank you brother
@@grendizer5439 peace, love, rock and roll
You sound just like Peter Finn. You may be from the same country.
拍一集手工輪胎平衡的影片❤❤❤❤❤😊
Where can I get the mounting/dismounting bar you use in the video. Thanks
It is made, not purchased.
detailed explanation
excellent
Thanks!
Where can i get this equipment? Please provide the site. Thanks
The changer can be purchased at Harbor Freight (US), PrincessAuto (CAN) or similar stores worldwide. The bar is DIY.
Anyone have a link to the rubber used on this? I have the new harbor freight one .
steel toe safety sandals
Super TOP .!!
Hi,
Could you plz tell me the price of this manual machine.
Regards
For the changer, before modifications, I paid about 50 dollars before tax.
仕事が丁寧やわー
ありがとう
Why do you have two heads on one end of your lever bar?
It would be very difficult to guide the bar with only one head. It is more stable (and easier) this way.
What do you use to make the centre cone?
1:28 reducer 2 inch to 1 1/2 inch.
Thank very much for sharing this information.
You are welcome!
Bonita esplicacio
Starałem się jak tylko mogłem.
Can anyone tell me why the tread width is in millimetres and the rim size is in inches?
To accommodate every system and stretch mind with math exercise.
very good
haha wearing socks and sandals. effing legend.
It's a fashion faux pas of the greatest magnitude to wear socks with open footwear. The real danger is not an injury to his foot, but to his reputation at prep school.
i have a harborfrieght tire changer...a year now..it now looks like a tractor trailer drive over it ..
What’re the pads you used for the bead breaker
Few years ago I bought it on line as a replacement part for different tire changer. Don't remember the name of the company. Can be easily done. A chunk of plastic can be bought at local supplier, same as the white plastic I bought for the changing bar.
@@robertdeptula2003 Thank you, also what did you use for the wheel reducer piece?
What do you mean by wheel reducer piece?
@@robertdeptula2003 the black center piece that holds the wheel down? right below the 4 prong thingy.
www.renodepot.com/en/abs-reducing-coupling-0068165
waw, mantab
И где купить такую штангу дв стороннюю?
Samoróbka
И где купить такую штангу???
Looks like your reducer is plastic is that correct ?
Yes, it is plastic reducer you can buy in plumbing section of any home improvement store.
Why can't you change an 18" wheel/tire with these low cost tire changers? Most of them say 16 or 16-1/2" maximum size.
All I have is 15 inches wheels.
Samłer już dis widziałem ;-)
No tak, bo ten kanał jest dwujęzyczny. Jestem Polakiem i mieszkam w Kanadzie. ... W zasadzie to powinienem dołożyć jeszcze francuski.
Hey this is Elijah McGaugh i need some 15" used car tires
It be nice if you show a tutorial how to make the bar or the tool however you want to call it some people might want to learn how to make it
This mount/demount bar is a simple build. All details are in the video, no hidden mechanisms or electronics. The only detail that you may not see is that plastics have metal inserts to keep it rigid. Good luck!
Gdzie kupiłeś tą łyżkę montażową? / Where you buy this tire changer bar?
Samoróba.
Robert Deptula zarąbista! Jak ją wykonałeś? Może zrób filmik jak ją zaprezentujesz. Mam tą montażownice ale ten oryginalny łom masakruje alusy :(
@@ukaszobrzut6093 Na moim kanale jest e-mail do kontaktów. Odezwij się.
Hey I need a used 15"car tire
I only have the other half of the tire if you are interested. :)