Thanks so much for making this video. The fault was your No.1 listed fault and exactly as you said the water supply failed while in the middle of hair washing!! New solenoid coil in the post and the shower should soon be up and running again. A great channel - super helpful and clear. You save me a fortune Shower Doctor - thanks a million!
Thank you so much for this easy to understand video. I am a 66yr old women who has no idea about plumbing. I now know what the problem is with my shower. Thank you so much for taking time out to help us.
Thanks - You've just saved me the ball-ache of swapping out a fairly new Triton shower and replacing the solenoid valve only with a part from a "scrap" unit. Superstar!
Hi George. Great thanks for your videos. Saved me a lot of time and aggravation by only needing to swap out a solenoid coil. Had planned to install a whole new unit, so this is a massive time & frustration saver. Really appreciate the effort you've gone to to make these videos. Thanks again.
1:01 thank you doctor shower!! This is the problem in my shower. I thought it was an electric fault but I have installed a new shower system of the same make and model of the old one and still got the same fault. I suspect that the culprit is a blockage in the drainage system of my washing machine. Could it be possible? Thanks! 💯👍🏼
My shower makes a noise like grinding then cuts out completely. My son checked the solenoid valve and the reading was just over 3.5. He also checked the tco continuity and that was fine. Any ideas please? Plumber is telling me to chuck the shower in the bin and but a new one 🙄 it only 3 years old but warranty has run out.
Good Morning I have watch a couple of your videos but have not found my fault but that could just be down to me; OK see if I can explain the problem! I went to have a shower yesterday and there was no water the pull cord showed it was on with a red light the shower had a red light but not water? I know it is getting on a bit so thought I will buy a new one fitted in turned the power on pulled the cord red light came on turn the new shower on and blow me there was no waster. As it was getting late I left it until this morning but what I did badd idea or not I fitted a cable to the old shower and switched it on and i could hear the pump so put a pipe on and it pump it out ( not very fast but the water was not under pressure ) so what could this be any help is well come.
Just subscribed to this excellent channel! Thanks to the shower doctor I have been able to change my solenoid and am now about to tackle the TCO. Never had so much use out of my multimeter!! ..lol. Great channel shower doctor!!
You prolly dont care but if you are bored like me atm then you can watch all the latest movies and series on instaflixxer. I've been binge watching with my gf for the last months xD
Hi I have a triton Amber 3 and thought my hose was leaking but actually after buying a new one I found out it’s when a shower head goes on it’s coming out the bottom of the head towards hose is that my prd as nothing wrong with no head on please help if poss and thanks for video
Hi what's about Mira atl advance, water stop coming at all. When I try to find solenoid valve it's look like doesn't exist on the market. Did my electic shower also have solenoid valve or is something else need to be exchange?
Aspirante Electric Shower 9.5Kw about 18 months old No hot water! Cold water flows I have follwed your guides. The TCO upper has continunity, (Checked in situ, not disconnected), as has the lower TCO continuity. Both Heater Cans show resistance as does the Solenoid Valve. I know this should not be tried! I pressed each of the tiny heater solenoids contacts on the PCB board with a screwdriver whilst the front cover was removed but front cover cable attached to PCB. Wow! The water flow got Hot! On releasing the pressure on each heater Solenoid Contact Points, the water ceases being heating. Now at a loss of what the problem is! Bye the way, the various switches on the cover appear to click ok.
thanks shower doc, these vids have helped me solve a problem, replaced solenoid. These vids are the heart and soul of humanity, free help from an expert is very inspirational and in this case, was very helpful. Thanks for doing what you do.
Thanks for all you do, very helpful. I have problem for anyone to comment on..... Triton T300si shower, 3 weeks old, the boiler was moved and since that happened the shower light for low pressure in on with cold water only. A pump was installed and is providing 1.6 bar at 12 ltrs a min to the shower. However the shower does not let any additional flow through and is still exactly the same. My theory is that when the boiler was moved they cut into the cold main (obviously) and this let the water out of the heating element. When the boiler move was completed, they did not purge the shower and subsequently the element has blown or something....? Any thoughts would be helpful.
Hi my problem is my shower only gets hot when it’s on full heat which is scalding when I turn it down to the blue it goes freezing I can’t get a medium temperature the indicator for the pressure drops straight to cold when I turn the temperature down, please advise me thanks ps it’s a triton T80SI thanks
Hi George, we have a manintenance contract on our central heating and recently called them out as our central heating was not working. The engineer fixed the issue but we noticed that our Mira Sport electric shower would not work when switched on - no water was coming through it. We tried it a few times but still nothing coming through despite the power light i identified that the problem was that the engineer had disconnected the cold water feed to the shower when he was checking the central heating pressure valve. He did not reconnect the water feed to the shower. I reconnected the feed and the water came through the shower but was running cold. So I have 2 questions. 1. What do you think the issue is? 2. Could this have been caused by turning the shower on without any water feed being connected ie is the fault caused by the engineer not reconnecting the cold water feed?
Hi all these videos from the shower doctor are so helpful! I think we've established my Mira Advance Flex shower has a solenoid valve issue as it keeps stopping then I have to turn it off at the switch then on again to make it work for another 3mins- but can anyone recommend any solenoid valve?? Thank you in Advance!
hi, Doc The trip fuse in the fuse box keeps tripping . We have a trition 7kw hand water heater just fitted, as DIy., the fuse in the isolate switch is 13 amp and does not blow. can you explain ?
Hello , Hope someone can help with this I've recently started to install a Triton Aspirante shower but when I've gone through the instalation and becoming stuck on getting any water to flow through. I've followed the steps in guide and got to turn knob all the way clock wise and put cover on without the cable installed ,then turn water on and power on then water should come through slowly and I'm suppose to turn any I clockwise to prime and to get all residue out . But nothings happening .... Can anyone assist , and help I'll be great full
Hi, just wanted to ask, what if the isolation switch doesn’t switch off or on? Mine is stuck on ‘on’ and won’t turn off, I have to hold the switch at an angle for the shower to turn on. Does that mean it’s the selonoid valve or something else? If anyone could shine some light I would be very grateful please 😢
Hey a jhave a mira sport max 108kw every job again it trips ou the rcb t randomly (mostly when herself is int there.) The 40 ecb is backed by a 50 mcb And ideas where I should start looking ?
Hi I have a Mira Sprint 8.5kW J08Da 46/14. Since last week, when it is turned off, cold water continues to flow gently from the head, not just a drip, any idea what is causing this and how to fix?
Thank you so much for sharing your knowledge. My Mira shower was cutting out after just a few minutes.No one wanted to look at it, just replace the whole unit, nearly £300 for the unit plus fitting. I watched your video and decided it was the solenoid cell, bought one for £13.50, and found someone prepared to fit it for £20! Shower back working properly. Delighted. Thank you.
What if the shower won't stop, even when I press the isolator switch? Mira vie electric. Already replaced the salanoid. I'm stumped as was my electrician
Hi great video , I have a triton t100xr I get lots of pressure and flow when it’s in the cold position. The problem is only get like warm water when it is turned to full heat and the flow is slow. Can you advice what the problem might be and what I can test as I have a simple test meter Thanks
Hopefully channel is still active. My issue is when you press the 'on' button, the shower will only come on for less than a second and then turns off. Every know and again on its own accord it will turn on as expected and work fine?
In number 1, by not enough power are you referring to the pressure being low? That is the issue with my t90sr. The flow is basically non existent and the water is always at the hottest when when you adjust the temperature
Hi. I have a mira shower which is controlled by a digital round controller which sends a wire less message to a black box in the airing cupboard which governs the heat as well as pumping. The problem I have is that the shower head only lets out cold water. Can you please give me any advice as to remedy this. Thank you
My Shower unit a Mira Sprint, Seems to be perpetually too hot. The regulator seems to have no effect on the amount of heat. If I drop the regulator to less than half the capacity the Low Flow light comes on and the water gets very cold. So it is either far too hot or far too cold. Do I need to change the Thermal cut out?
My Creda 950DL electric shower doesn’t work properly. The Mid LED light stays off - water runs cold at full pressure. Turned the water flow dial to extreme hot - then water gets lukewarm, while the flow from the showerhead is weak. Both High LEDs stays on, while the Mid LED stay off. After watching your repair video, I tested components… I then tried to remove component/s. However, after spending about an hour trying…I found they were not straightforward to remove. I then replaced the cover and left it. I suppose because the Creda 950DL is so difficult to repair, why there is no information online showing how to repair them??? So, I guess it's a new shower?!
Hi. I really like your channel. I have a Mira Elite QT shower and the water stopped flowing yesterday. I opened the unit and there was a good deal of carbon dust inside the shower. I don't particularly want to replace the whole shower unit. Could my problem be the solenoid or the brushes that need replacement? Thanks a million
What if water flow low and water is hot? Inlet filter issue blocked or something else? My fault is water flow is fine if first start and then if I switch off and on, water flow is low and water is hot.
My Bosh water heater is brand new, my water connections are brand new. What did I do wrong? My problem is that I set the water at a comfortable position, after few seconds, the water temperature starts getting hotter and hotter until I can´t tolerate it. I Adjust the water faucet to get more cold water, and it works but just for a few seconds again. I keep adjusting the water faucet until the heater stops working because the low flow. What can it be my problem? I have a main 3/4 line, I put a T to get cold water to my shower, about 2 feet I put another T to get could water to my sink, then from the same main line I put another T for my toilet. From the toilet line I put a T to get cold water to my tankless water heater. On my water heater outlet I put another T to feed hot water to my sink and my shower. What am I doing wrong?
Hi George, i have a mira elite 2 ,which was installed ten years ago,when switched on the flow is very very poor.I removed the cover and all parts were covered in black carbon,i noticed that the brushes are worn as is the communator .Ive decided to replace the mira as i would find it impossible to remove the motor.Hope im doing the right thing.Kevin
I've just made an order on your site for a solenoid and microswitch for a Neptune Solo having watched this video and the instructional one on fitment. Thank you very much 🙂 One criticism:- my unit is discontinued, so I cannot get a replacement value, therefore I will need to salvage the old one and I risk damaging an o-ring in the process. I have had to order a selection of o-rings on Amazon just in case. I would have though you guys could put together a smaller pack of common shower o-rings yourself that people would happily order alongside your spare parts. It would compliment the silicone grease pot you already sell.
hello shower doctor , my triton shower has lost water pressure and the power light is not showing lite up when shower is on 1 any advice for me plz ? thanks
Very informative video but one fault that is very common but not mentioned here is the persistent dripping from outlet pipe even when shower is off. PRD ball still in place, shower works fine otherwise, could it be solenoid in some way or some deposit sitting somewhere preventing a valve from closing, any ideas? I have this problem and I know others who have had it and just bought a new shower!
Hiya. Watched/liked yur YT vids. Bathroom shower power cord switch (oppo corner to shower) broke .. switch on = single pull, switch off= 300 pulls /clicks and counting. Cant find matching YT vid. Can i buy new switch and follow steps in a "replace pull cord" vid. Got nc voltage tester, multimeter=safety 1st. Many thanks in advance. Cheers. Gary
Aqualisa Lumi Electric Shower stuck to the max heat. Nothing happening when you turn dial down or up, it's on max all the time. I have the shower for 2 years, and it was no problems till today! I went in shower and its boiling water coming out from shower! What can be the problem? Thanks
So I have the issue of water not starting, the solenoid reads just over 4kohms, if I bang on the solenoid and plunger it sometimes manages to open, sometimes doesn’t. Is it the entire water section that needs replacing?
The motor in my shower sounds weak and puts out cold water, if I hit the front it kicks in and puts out warm water but is still quieter than it should be. Any guesses what is wrong?
Hello doc, thanks for your service. My electric shower neither pump nor heat the water. All I get is just cold water coming out from the water tank when I turned on the heater. How can I figure out what the problem is?
My shower is spluttering then turns off, after some time it turns on randomly. This has been happening every few days. I'm not sure if I should report it to landlord. What's happening???
hi I have a t70 gsi+, since it was first fitted it never is really that hot, I adjusted the mains water valve down to just above the minimum 0.7 bar setting. when I drop below that it switches the elements of so that part is working but the only way I can get any heat is just above this but the pressure out of the shower is pathetic. it seems as if it's only using one element when there's too much pressure. It's really hit and miss to get it right
Would a faulty solenoid valve prevent all power getting to my Gainsborough 2000x and stopping the indicator lights from illuminating as well as not allowing water through also. Thanks in advance.
Hi George. I replaced my solinoid valve and the water ran fine again and the shower was hot. I left it running for 5 mins and then I stepped in to have a shower but by this time the water temperature dropped dramatically and i tried everything including a continuity test on the TCO switch and it was fine so I'm baffled now as to the newest problem. possibly a heating element issue I'm just not sure.
Hi Shower Doctor, my problem is when i touched the water control this is made of stainless it is grounded and it is dangerous for my children. How can i solve this problem. Thanks
Love the videos! A new Trition ast 1000 installed less than a month ago. Had last one replaced because we had no cold water, the new one is now doing the same, can you help?? Thanks
Hi George, amazing video. Just wondering what causes the shower to stop working every 3 months and I need to get a new one every time. My landlord had put 4 new showers through last year and a half. We have low water pressure. Is that an issue that keeps killing the shower?
Thanks and well done......But, you have missed a quick wee bit of info you could have used. The solenoid valve can fail in both the open and closed position........So No water and also constant water. Which is the problem I have.
I recently bought a Triton T80Z 10.5 KW from your good selves. It works fine but the thermal cut out is operating prematurely for my requirements. I need to hot shower for more than the normal time. There are thousands of eczema sufferers who get relief by hot showering. Is it possible to get a less sensitive TCO? My old Galaxy Aqua 3000 (obtained from your good selves) did not have this premature cut-out and that lasted over ten years. I tried to get a replacement but as you know they are no longer available.
hey doc was wondering if you maybe to help, i have a german aeg tankless water heater , it was power going to it but no power to heat the water, its just running and not turning on
how do i change 45A shower switch? the switch beside the one you changed in the video above, as my 45A shower switch keeps breaking, & i have 2 call an electrician every 3 weeks. can you do a video of changing 45A shower switch please.
Hi. I just wanted to get some advice if I may please? My girlfriend took a shower yesterday and since she finished using it and switched it off by the button, the shower head continues to drip water as if its not turned off properly. The drip is not the equivalent of if it was turned on fully. It's like as if, if it had a faucet, the faucet wouldn't be fully turned for it to be off. I've unscrewed the hose from the bottom and theres water coming out of the bottom. If theres a faulty part I can replace, I'd be happy to have a go at repairing it. I replaced the solenoid valve on this shower thanks to your RUclips video a few months ago when the shower wasn't coming on any more and it fixed it! My shower is a Triton Rapide 3+.
hi, i have a redring expressions shower and the water is cold. if i unscrew the shower head and place my finger against the hose end to stop the water running and turn the shower on i can feel the water getting hot. when i take away my finger and let the water run- it gets colder very quickly. can you help ?
Any idea what would cause smoke to bellow out of a Triton shower?? I'm on the end of their engineers not turning up... head office trying to convince me that it has not been installed incorrectly and generally different information from their head office.
I have this same problem. Sparky friends on FB suggested it's a loose connection that got hot and started burning the wire inside. That's the smell you're smelling. I've just replaced the faulty wire (mine was a blue wire) with a good one and cleaned the corroded terminal (mine were spade connectors) and that should be good enough until I can get a new shower unit. Hope that helps! - I've just had it running for 20 mins, all working as it should and no burning smell. Good luck!
Hey there, was hoping for a bit of advice. Pretty sure the PRD has gone in our shower as there is water coming from the bottom of it. It's not a 'leak' though as it's coming out with a lot of force and is draining almost all of the pressure from the shower. We have a Triton T70si and it's coming from around the middle of the unit rather than where the hose connects - I had a look at your PRD replacement video and you replace a part that is connected to the hose which threw me off a little bit (as I said the leak isn't coming from the hose it's from the centre of the shower) Does this mean I need a different part as I'm probably gonna do this as a DIY job.
Hi there, George has answered your question during our livestream last week! Here's the link: ruclips.net/video/bBX3zJgI9dU/видео.htmlm28s (and sorry for misspelling your nickname).
Thanks so much for making this video. The fault was your No.1 listed fault and exactly as you said the water supply failed while in the middle of hair washing!! New solenoid coil in the post and the shower should soon be up and running again. A great channel - super helpful and clear. You save me a fortune Shower Doctor - thanks a million!
Thank you so much for this easy to understand video. I am a 66yr old women who has no idea about plumbing. I now know what the problem is with my shower. Thank you so much for taking time out to help us.
Thanks - You've just saved me the ball-ache of swapping out a fairly new Triton shower and replacing the solenoid valve only with a part from a "scrap" unit. Superstar!
This Guy is Great, straight to the issues not too wordy, and truly is an Expert of his trade, thanks for the insights , Jim the Elec
Hi George. Great thanks for your videos. Saved me a lot of time and aggravation by only needing to swap out a solenoid coil. Had planned to install a whole new unit, so this is a massive time & frustration saver. Really appreciate the effort you've gone to to make these videos. Thanks again.
Hi Alex, thank you for your comment! George has mentioned it during our live stream last night: bit.ly/2pYl1MU (watch from around 27min 15sec).
George Hi. Just a line to say thanks solenoid coil €17.96. €8 postage family of 6 now clean. Thanks for the great videos many thanks.
thanks very much for explanation
Excellent video - Thank you.
I managed to work-out that my Triton T80 has a faulty Solenoid coil (gone O/C) - I've ordered a new one.
1:01 thank you doctor shower!! This is the problem in my shower. I thought it was an electric fault but I have installed a new shower system of the same make and model of the old one and still got the same fault.
I suspect that the culprit is a blockage in the drainage system of my washing machine. Could it be possible?
Thanks! 💯👍🏼
Thanks again so very very much
My shower makes a noise like grinding then cuts out completely. My son checked the solenoid valve and the reading was just over 3.5. He also checked the tco continuity and that was fine. Any ideas please? Plumber is telling me to chuck the shower in the bin and but a new one 🙄 it only 3 years old but warranty has run out.
Good Morning I have watch a couple of your videos but have not found my fault but that could just be down to me; OK see if I can explain the problem! I went to have a shower yesterday and there was no water the pull cord showed it was on with a red light the shower had a red light but not water? I know it is getting on a bit so thought I will buy a new one fitted in turned the power on pulled the cord red light came on turn the new shower on and blow me there was no waster.
As it was getting late I left it until this morning but what I did badd idea or not I fitted a cable to the old shower and switched it on and i could hear the pump so put a pipe on and it pump it out ( not very fast but the water was not under pressure ) so what could this be any help is well come.
Excellent and very informative
Just subscribed to this excellent channel! Thanks to the shower doctor I have been able to change my solenoid and am now about to tackle the TCO. Never had so much use out of my multimeter!! ..lol. Great channel shower doctor!!
You prolly dont care but if you are bored like me atm then you can watch all the latest movies and series on instaflixxer. I've been binge watching with my gf for the last months xD
@Justus Pierce yea, been watching on Instaflixxer for since november myself :D
Hi I have a triton Amber 3 and thought my hose was leaking but actually after buying a new one I found out it’s when a shower head goes on it’s coming out the bottom of the head towards hose is that my prd as nothing wrong with no head on please help if poss and thanks for video
Hi Mira electric shower needs to bang it to switch off i have cheched the power botom is ok what could that be?
Hi what's about Mira atl advance, water stop coming at all.
When I try to find solenoid valve it's look like doesn't exist on the market.
Did my electic shower also have solenoid valve or is something else need to be exchange?
Thank you very much
Aspirante Electric Shower 9.5Kw about 18 months old No hot water! Cold water flows I have follwed your guides.
The TCO upper has continunity, (Checked in situ, not disconnected), as has the lower TCO continuity.
Both Heater Cans show resistance as does the Solenoid Valve.
I know this should not be tried! I pressed each of the tiny heater solenoids contacts on the PCB board with a screwdriver whilst the front cover was removed but front cover cable attached to PCB. Wow! The water flow got Hot! On releasing the pressure on each heater Solenoid Contact Points, the water ceases being heating.
Now at a loss of what the problem is! Bye the way, the various switches on the cover appear to click ok.
My Triton started to run cold only. I tried the TCO reset but it's still the same. Any ideas please?
thanks shower doc, these vids have helped me solve a problem, replaced solenoid. These vids are the heart and soul of humanity, free help from an expert is very inspirational and in this case, was very helpful. Thanks for doing what you do.
Thanks for all you do, very helpful.
I have problem for anyone to comment on.....
Triton T300si shower, 3 weeks old, the boiler was moved and since that happened the shower light for low pressure in on with cold water only.
A pump was installed and is providing 1.6 bar at 12 ltrs a min to the shower.
However the shower does not let any additional flow through and is still exactly the same.
My theory is that when the boiler was moved they cut into the cold main (obviously) and this let the water out of the heating element.
When the boiler move was completed, they did not purge the shower and subsequently the element has blown or something....?
Any thoughts would be helpful.
Hi my problem is my shower only gets hot when it’s on full heat which is scalding when I turn it down to the blue it goes freezing I can’t get a medium temperature the indicator for the pressure drops straight to cold when I turn the temperature down, please advise me thanks ps it’s a triton T80SI thanks
very useful video, saved me a bit of money,Thank you.
What about making bip noise. Thanks
Hi George, we have a manintenance contract on our central heating and recently called them out as our central heating was not working. The engineer fixed the issue but we noticed that our Mira Sport electric shower would not work when switched on - no water was coming through it. We tried it a few times but still nothing coming through despite the power light i identified that the problem was that the engineer had disconnected the cold water feed to the shower when he was checking the central heating pressure valve. He did not reconnect the water feed to the shower. I reconnected the feed and the water came through the shower but was running cold. So I have 2 questions. 1. What do you think the issue is? 2. Could this have been caused by turning the shower on without any water feed being connected ie is the fault caused by the engineer not reconnecting the cold water feed?
Hi all these videos from the shower doctor are so helpful! I think we've established my Mira Advance Flex shower has a solenoid valve issue as it keeps stopping then I have to turn it off at the switch then on again to make it work for another 3mins- but can anyone recommend any solenoid valve?? Thank you in Advance!
my triton shower will not switch on when the button is pressed? any advice?
hi, Doc
The trip fuse in the fuse box keeps tripping . We have a trition 7kw hand water heater just fitted, as DIy., the fuse in the isolate switch is 13 amp and does not blow. can you explain ?
Avnish...
Put a stick of dynamite in there and light it, I guarantee it will blow the fuse!
Hi, could you please explain about pump faulty, how to replace pump or to how to clean filter? Thanks
Hiya I got a question...my shower is either too hot or too cold...It can't have the settings that you want it to be..have any idea?
Many, many thanks Doc. You have a new subscriber, in me.
at least I know the reason why water stops and what to discuss with an electrician. thanks a lot
Hello ,
Hope someone can help with this I've recently started to install a Triton Aspirante shower but when I've gone through the instalation and becoming stuck on getting any water to flow through. I've followed the steps in guide and got to turn knob all the way clock wise and put cover on without the cable installed ,then turn water on and power on then water should come through slowly and I'm suppose to turn any I clockwise to prime and to get all residue out . But nothings happening ....
Can anyone assist , and help I'll be great full
Very well explained. My solenoid valve has gone wrong. Now it's a case of replacing it. 👍
Hi, just wanted to ask, what if the isolation switch doesn’t switch off or on? Mine is stuck on ‘on’ and won’t turn off, I have to hold the switch at an angle for the shower to turn on. Does that mean it’s the selonoid valve or something else? If anyone could shine some light I would be very grateful please 😢
My Triton As2000xt adjustable dial is completely stuck( hot and cold) help
mine won't come one it hade just hade a new valve put in now it won't come on a few days off being fixed
Hey a jhave a mira sport max 108kw every job again it trips ou the rcb t randomly (mostly when herself is int there.) The 40 ecb is backed by a 50 mcb
And ideas where I should start looking ?
Hi I have a Mira Sprint 8.5kW J08Da 46/14. Since last week, when it is turned off, cold water continues to flow gently from the head, not just a drip, any idea what is causing this and how to fix?
Really helpful video. Fixed our Mira Sprint's faulty solenoid without any problems. Many thanks.
Thank you so much for sharing your knowledge. My Mira shower was cutting out after just a few minutes.No one wanted to look at it, just replace the whole unit, nearly £300 for the unit plus fitting. I watched your video and decided it was the solenoid cell, bought one for £13.50, and found someone prepared to fit it for £20! Shower back working properly. Delighted. Thank you.
Glad we could help!
What if the shower won't stop, even when I press the isolator switch? Mira vie electric. Already replaced the salanoid. I'm stumped as was my electrician
Can you replace the mini rubber ring that goes on the shower head?
Hi great video , I have a triton t100xr I get lots of pressure and flow when it’s in the cold position. The problem is only get like warm water when it is turned to full heat and the flow is slow. Can you advice what the problem might be and what I can test as I have a simple test meter
Thanks
what could be the reason for an electric shower to make a banging noise when changing from cold setting to hot setting?
Thanks
Hopefully channel is still active. My issue is when you press the 'on' button, the shower will only come on for less than a second and then turns off. Every know and again on its own accord it will turn on as expected and work fine?
In number 1, by not enough power are you referring to the pressure being low? That is the issue with my t90sr. The flow is basically non existent and the water is always at the hottest when when you adjust the temperature
if the problem with my shower is the thermal cut out how do i fix this please
Hi iam changing my shower to a 400mm rainfall shower head what’s the best type of shower to install .pete
Hi. I have a mira shower which is controlled by a digital round controller which sends a wire less message to a black box in the airing cupboard which governs the heat as well as pumping. The problem I have is that the shower head only lets out cold water. Can you please give me any advice as to remedy this. Thank you
My Shower unit a Mira Sprint, Seems to be perpetually too hot. The regulator seems to have no effect on the amount of heat. If I drop the regulator to less than half the capacity the Low Flow light comes on and the water gets very cold. So it is either far too hot or far too cold. Do I need to change the Thermal cut out?
My Creda 950DL electric shower doesn’t work properly.
The Mid LED light stays off - water runs cold at full pressure. Turned the water flow dial to extreme hot - then water gets lukewarm, while the flow from the showerhead is weak. Both High LEDs stays on, while the Mid LED stay off.
After watching your repair video, I tested components… I then tried to remove component/s. However, after spending about an hour trying…I found they were not straightforward to remove. I then replaced the cover and left it.
I suppose because the Creda 950DL is so difficult to repair, why there is no information online showing how to repair them???
So, I guess it's a new shower?!
Well thanks had new shower fitted and only lukewarm water temp hoping it's just water pressure type problem and a shower pump will solve it
Hi. I really like your channel. I have a Mira Elite QT shower and the water stopped flowing yesterday. I opened the unit and there was a good deal of carbon dust inside the shower. I don't particularly want to replace the whole shower unit. Could my problem be the solenoid or the brushes that need replacement? Thanks a million
What if water flow low and water is hot? Inlet filter issue blocked or something else? My fault is water flow is fine if first start and then if I switch off and on, water flow is low and water is hot.
My Bosh water heater is brand new, my water connections are brand new. What did I do wrong? My problem is that I set the water at a comfortable position, after few seconds, the water temperature starts getting hotter and hotter until I can´t tolerate it. I Adjust the water faucet to get more cold water, and it works but just for a few seconds again. I keep adjusting the water faucet until the heater stops working because the low flow.
What can it be my problem? I have a main 3/4 line, I put a T to get cold water to my shower, about 2 feet I put another T to get could water to my sink, then from the same main line I put another T for my toilet. From the toilet line I put a T to get cold water to my tankless water heater. On my water heater outlet I put another T to feed hot water to my sink and my shower. What am I doing wrong?
Hi George, i have a mira elite 2 ,which was installed ten years ago,when switched on the flow is very very poor.I removed the cover and all parts were covered in black carbon,i noticed that the brushes are worn as is the communator .Ive decided to replace the mira as i would find it impossible to remove the motor.Hope im doing the right thing.Kevin
I am competent using an electric meter ( I still have an old AVO ) thanks Shower Doctor for giving the 'lowdown'
The brand of my Tankless shower heater is Champs UK technolgy.
I've just made an order on your site for a solenoid and microswitch for a Neptune Solo having watched this video and the instructional one on fitment. Thank you very much 🙂
One criticism:- my unit is discontinued, so I cannot get a replacement value, therefore I will need to salvage the old one and I risk damaging an o-ring in the process. I have had to order a selection of o-rings on Amazon just in case.
I would have though you guys could put together a smaller pack of common shower o-rings yourself that people would happily order alongside your spare parts. It would compliment the silicone grease pot you already sell.
hello shower doctor , my triton shower has lost water pressure and the power light is not showing lite up when shower is on 1 any advice for me plz ? thanks
my shower button doesn't work. but the ceiling cord turns the water on but it's not heated. any ideas? thanks
Very informative video but one fault that is very common but not mentioned here is the persistent dripping from outlet pipe even when shower is off. PRD ball still in place, shower works fine otherwise, could it be solenoid in some way or some deposit sitting somewhere preventing a valve from closing, any ideas? I have this problem and I know others who have had it and just bought a new shower!
replace solenoid to fix this
Is it worth getting these parts replaced or just get the manufacturer to replace the whole thing under their fixed fee repair services?
please help -fitted new shower Triton T70GSI cut out within minute of using hot shower, no issue when using cold shower. 7 days old shower
I have a power shower when I turn the power up it makes a loud noise like it’s struggling for water.
Hiya. Watched/liked yur YT vids. Bathroom shower power cord switch (oppo corner to shower) broke .. switch on = single pull, switch off= 300 pulls /clicks and counting. Cant find matching YT vid. Can i buy new switch and follow steps in a "replace pull cord" vid. Got nc voltage tester, multimeter=safety 1st. Many thanks in advance. Cheers. Gary
Aqualisa Lumi Electric Shower stuck to the max heat. Nothing happening when you turn dial down or up, it's on max all the time. I have the shower for 2 years, and it was no problems till today! I went in shower and its boiling water coming out from shower! What can be the problem? Thanks
So I have the issue of water not starting, the solenoid reads just over 4kohms, if I bang on the solenoid and plunger it sometimes manages to open, sometimes doesn’t. Is it the entire water section that needs replacing?
I have an Aqualisa quartz shower. Both buttons LED are on but shower not working. Can I reset the controller?
The motor in my shower sounds weak and puts out cold water, if I hit the front it kicks in and puts out warm water but is still quieter than it should be. Any guesses what is wrong?
Hello doc, thanks for your service. My electric shower neither pump nor heat the water. All I get is just cold water coming out from the water tank when I turned on the heater. How can I figure out what the problem is?
My shower is spluttering then turns off, after some time it turns on randomly. This has been happening every few days. I'm not sure if I should report it to landlord. What's happening???
hi I have a t70 gsi+, since it was first fitted it never is really that hot, I adjusted the mains water valve down to just above the minimum 0.7 bar setting. when I drop below that it switches the elements of so that part is working but the only way I can get any heat is just above this but the pressure out of the shower is pathetic. it seems as if it's only using one element when there's too much pressure. It's really hit and miss to get it right
I have Gainsborough delux 10.5 and it is either boiling hot or freezing, no in between. can this be fixed or do I need a whole engine?
Would a faulty solenoid valve prevent all power getting to my Gainsborough 2000x and stopping the indicator lights from illuminating as well as not allowing water through also. Thanks in advance.
Hi,
I have a Mira jump shower, the power switch stopped working. I think the problem is from the latching switch. How do I replace it?
Great video,thank you.
Hi George. I replaced my solinoid valve and the water ran fine again and the shower was hot. I left it running for 5 mins and then I stepped in to have a shower but by this time the water temperature dropped dramatically and i tried everything including a continuity test on the TCO switch and it was fine so I'm baffled now as to the newest problem. possibly a heating element issue I'm just not sure.
My triton t90 xr is not getting up to temperature, it sounds like the element. Can they be replaced or will I need a complete new shower ?
Solenoid
I keep the tools and a solenoid in the bathroom because im bloody sick of it stopping when im covered in soap
Hi Shower Doctor, my problem is when i touched the water control this is made of stainless it is grounded and it is dangerous for my children. How can i solve this problem. Thanks
best ever explain
Love the videos! A new Trition ast 1000 installed less than a month ago. Had last one replaced because we had no cold water, the new one is now doing the same, can you help?? Thanks
I have a Gainsborough 9.5kw, but the solenoid valve isn't visible?
Hi George, amazing video. Just wondering what causes the shower to stop working every 3 months and I need to get a new one every time. My landlord had put 4 new showers through last year and a half. We have low water pressure. Is that an issue that keeps killing the shower?
when i turn mine on its hot won't mix but when i press just cold button its cold help aquatronic 4 plus
Very good Guide,Thank you.
Hi. Thanks fir video. What about if you on shower and about 1 min go only cold water then starts works fine and flow hot water?
Thank you
Thanks and well done......But, you have missed a quick wee bit of info you could have used. The solenoid valve can fail in both the open and closed position........So No water and also constant water. Which is the problem I have.
I recently bought a Triton T80Z 10.5 KW from your good selves. It works fine but the thermal cut out is operating prematurely for my requirements. I need to hot shower for more than the normal time. There are thousands of eczema sufferers who get relief by hot showering. Is it possible to get a less sensitive TCO? My old Galaxy Aqua 3000 (obtained from your good selves) did not have this premature cut-out and that lasted over ten years. I tried to get a replacement but as you know they are no longer available.
hey doc was wondering if you maybe to help, i have a german aeg tankless water heater , it was power going to it but no power to heat the water, its just running and not turning on
how do i change 45A shower switch? the switch beside the one you changed in the video above, as my 45A shower switch keeps breaking, & i have 2 call an electrician every 3 weeks. can you do a video of changing 45A shower switch please.
Hi.
I just wanted to get some advice if I may please? My girlfriend took a shower yesterday and since she finished using it and switched it off by the button, the shower head continues to drip water as if its not turned off properly. The drip is not the equivalent of if it was turned on fully. It's like as if, if it had a faucet, the faucet wouldn't be fully turned for it to be off. I've unscrewed the hose from the bottom and theres water coming out of the bottom. If theres a faulty part I can replace, I'd be happy to have a go at repairing it. I replaced the solenoid valve on this shower thanks to your RUclips video a few months ago when the shower wasn't coming on any more and it fixed it!
My shower is a Triton Rapide 3+.
hi have triton t90sr and when i turn of power water still comming from head cold water
hi, i have a redring expressions shower and the water is cold. if i unscrew the shower head and place my finger against the hose end to stop the water running and turn the shower on i can feel the water getting hot. when i take away my finger and let the water run- it gets colder very quickly. can you help ?
Any idea what would cause smoke to bellow out of a Triton shower?? I'm on the end of their engineers not turning up... head office trying to convince me that it has not been installed incorrectly and generally different information from their head office.
I have this same problem. Sparky friends on FB suggested it's a loose connection that got hot and started burning the wire inside. That's the smell you're smelling. I've just replaced the faulty wire (mine was a blue wire) with a good one and cleaned the corroded terminal (mine were spade connectors) and that should be good enough until I can get a new shower unit. Hope that helps!
- I've just had it running for 20 mins, all working as it should and no burning smell. Good luck!
@@agentling1 Many thanks!!
Excellent videos!
Hey there, was hoping for a bit of advice. Pretty sure the PRD has gone in our shower as there is water coming from the bottom of it. It's not a 'leak' though as it's coming out with a lot of force and is draining almost all of the pressure from the shower.
We have a Triton T70si and it's coming from around the middle of the unit rather than where the hose connects - I had a look at your PRD replacement video and you replace a part that is connected to the hose which threw me off a little bit (as I said the leak isn't coming from the hose it's from the centre of the shower) Does this mean I need a different part as I'm probably gonna do this as a DIY job.
Hi there, George has answered your question during our livestream last week! Here's the link: ruclips.net/video/bBX3zJgI9dU/видео.htmlm28s (and sorry for misspelling your nickname).