For button 1 and 2 you need a cable for each going to the ground pin on the pi. Physical number of the pin is 6. Its the 4th down on the outer edge of the board. The remaining cable for button 1 goes to GPIO pin 17 (phys number 11 or the 6th down of the inner row) and the remaining cable for button 2 goes to GPIO pin 27 (phys number 13 or the 7th pin down from the inner row). Here is another diagram with the pin outs that may paint a better picture. pinout.xyz/
They work by default without added config. What's happening on your end to try to help you out? Make sure the wiring is correct as per the diagram here documentation.pibooth.org/en/stable/sources/install.html#circuit-diagram
Thx a lot, it works fine now, the countdown on the pixel ring is on rainbow color and i power it via the gpio pins, why did you power it via usb, is the pi not strong enough?
While it can power the lights, too many running at it's highest brightness can damage the board. I can't remember the safe number others have calculated online on how many LEDs you can drive but 16 was too many in my case
@@geekydad8565 I am currently in the process of rebuilding a photo booth, but at the moment I'm having issues with the Raspberry Pi. When I start Pibooth, a small window opens, but then the program crashes. I'm not sure what's causing this problem or how to fix it.
@ElfenBoss18 if you run the pibooth command from s terminal you'll at least get errors from there. If you rely on the auto startup then it will disappear. In my case the errors usually relate to the camera not being detected on startup. Let us know how you go
@@geekydad8565 Hello ; ) I managed to get it to start, I had a Raspberry 4 and there were complications that I fixed ;) now I have to get the QR code and upload the photo
Hi, if you're asking about the wiring here is a circuit diagram which may help. documentation.pibooth.org/en/stable/sources/install.html#circuit-diagram. Can you please give me more detail on what you mean by config? Works out of the box so you shouldn't need any
Possibly but not sure of what things you may need to overcome (if any). Doing a quick Google search, someone online claims they have done it for themselves too.
For the two front buttons I didn't need to. They work out of the box. You'll just need to be sure you wire it up correctly like in the diagram. Unless you're talking about the power button?
Does the QR code work for you even though it is small? Originally the QR code is small but it didn't work until I configured it to use the dropbox URL. The longer the URL the bigger the QR code. Also the smaller the screen and higher the resolution setting the smaller everything will be on your display. What size screen and what resolution are you using?
Eeek..i can't remember. I was bulding this with my kids so I had to go slow and it was my first time using a table saw. A lot of start and stop and trial and error. It was no weekend project! Take the box out of it and the rest can be done in hours
I did mine via usb. FYI Pibooth won't run if you don't have a camera connected to it when it starts unless you have a plugin installed for debugging that pretends there is a camera active. Might be the reason why you are having issue. I think this is a compatible list that I just googled. The DSLR needs to be compatible with gphoto2. gphoto.org/proj/libgphoto2/support.php
I haven't come across this error but if you're using the DSLR you need to add an extra variable during installation for DLSR specifically. Not sure what else it may be otherwise. Maybe not a supported model???
Nice one. I will rebuild it for my wedding! :) ❤
Great idea and congrats for the upcoming nuptials
very good video thanks, everything is well explained !
Hello, Thank you, it works, can you tell me if it is possible to modify the portrait and landscape state by pressing a push button?
Hi, it's not available as a standard. It could be a feature request you can make on their git or try develop yourself a plugin
Great video, beautifully detailed. I also want to build one with a DSLR camera, I think it should be possible.
Before my pi cam was delivered I used a DSLR to test which worked for me. Good luck and let me know how you go
Thank you for your response. But I still don't understand how you connected the 2 buttons for selecting 1 or 3 photos on which GPIO pin?
For button 1 and 2 you need a cable for each going to the ground pin on the pi. Physical number of the pin is 6. Its the 4th down on the outer edge of the board. The remaining cable for button 1 goes to GPIO pin 17 (phys number 11 or the 6th down of the inner row) and the remaining cable for button 2 goes to GPIO pin 27 (phys number 13 or the 7th pin down from the inner row). Here is another diagram with the pin outs that may paint a better picture. pinout.xyz/
You blinking Rock!
I read this comment with tired eyes and had the image of a stone with eyes
I'm talking about the button you added for photo selection.
They work by default without added config. What's happening on your end to try to help you out? Make sure the wiring is correct as per the diagram here documentation.pibooth.org/en/stable/sources/install.html#circuit-diagram
Thx a lot, it works fine now, the countdown on the pixel ring is on rainbow color and i power it via the gpio pins, why did you power it via usb, is the pi not strong enough?
While it can power the lights, too many running at it's highest brightness can damage the board. I can't remember the safe number others have calculated online on how many LEDs you can drive but 16 was too many in my case
Danke Sehr grüße aus Deutschland :)
You are very welcome. Thank you for your support!
@@geekydad8565
I am currently in the process of rebuilding a photo booth, but at the moment I'm having issues with the Raspberry Pi. When I start Pibooth, a small window opens, but then the program crashes. I'm not sure what's causing this problem or how to fix it.
@ElfenBoss18 if you run the pibooth command from s terminal you'll at least get errors from there. If you rely on the auto startup then it will disappear. In my case the errors usually relate to the camera not being detected on startup. Let us know how you go
@@geekydad8565 Hello ; ) I managed to get it to start, I had a Raspberry 4 and there were complications that I fixed ;)
now I have to get the QR code and upload the photo
@christophernowack4971 great progress. Sorry I couldn't help there. At the time i set mine up the pi4 was not compatible
hello how do you add a second button for 3 picture and what modification in the config file thank you
Hi, if you're asking about the wiring here is a circuit diagram which may help. documentation.pibooth.org/en/stable/sources/install.html#circuit-diagram. Can you please give me more detail on what you mean by config? Works out of the box so you shouldn't need any
I have everything set up with DSLR and printer, could it be that pibooth does not start if no camera is connected?
Awesome project ! Will it run on pi zero w also ?
Possibly but not sure of what things you may need to overcome (if any). Doing a quick Google search, someone online claims they have done it for themselves too.
@@geekydad8565will dive into this thanks mate !
I would need to see your configured file to know which line you modified to add a button.
For the two front buttons I didn't need to. They work out of the box. You'll just need to be sure you wire it up correctly like in the diagram. Unless you're talking about the power button?
@@TheAirSit for the power button its in the boot config file. I have the command in the video description too if you haven't seen it
hello how do you have a large qr code mine is very small thank you
Sorry can you please rephrase your question, I do not understand
hello, the qr code is very large on the screen and mine is very small
Does the QR code work for you even though it is small? Originally the QR code is small but it didn't work until I configured it to use the dropbox URL. The longer the URL the bigger the QR code. Also the smaller the screen and higher the resolution setting the smaller everything will be on your display. What size screen and what resolution are you using?
Skimming through how much do you think you spent in total making this?
Eeek..i can't remember. I was bulding this with my kids so I had to go slow and it was my first time using a table saw. A lot of start and stop and trial and error. It was no weekend project! Take the box out of it and the rest can be done in hours
How do i connect the dslr with pi via usb or wifi?
I did mine via usb. FYI Pibooth won't run if you don't have a camera connected to it when it starts unless you have a plugin installed for debugging that pretends there is a camera active. Might be the reason why you are having issue. I think this is a compatible list that I just googled. The DSLR needs to be compatible with gphoto2. gphoto.org/proj/libgphoto2/support.php
i get this error pygame.error: video system not initialized
I haven't come across this error but if you're using the DSLR you need to add an extra variable during installation for DLSR specifically. Not sure what else it may be otherwise. Maybe not a supported model???