That's the second thing I changed on my daughter's 08 mazda3 2.3l . I changed tge sensor it showed on my reader first (output shaft sensor). Fixed it..costly, but fixed (new TCM).
Thank you for showing how to remove the computer hookups - I'm not skilled in car repair at all, and I got hung up at that part. Tons of other videos skip this! THANK YOU!
@@asianmechanicguy6483 okay I just got my module back and installed it and it’s still doing the same thing. If that module is fixed is there something else I need to do? I figured all errors would be cleared out since the battery has been out for a week. Help please. Thanks.
Thanks for the video my friend! I have a 2006 mazda 3 everything works fine except when I put it in reverse it takes like 2 minutes to go in reverse.. do you think it's the same problem? Any ideas anyone? Muchas gracias
Iv seen this a lot actually lol. Its a manual right? The manual actually tells you, if you havs this problem, to put it in neutral and release the clutch and try again. Its a very common problem from what iv heard and i get the same problem. The only thing that helps is putting it in neutral and releasing the clutch and then trying again
Good day man. Do you think you can help me out. I've got the following issue. I have a 2006 mazda 3 automatic The AT icon lights up after about 10 mins of driving The car is not shifting properly, the shifts are a bit delayed and they become hard shifts after the AT lights up. Also the gears dont come down from 4th or 3rd unless I practically stop. The gears in M mode are not displaying either. Thank you in advance!
@@asianmechanicguy6483 hello, is this piece expensive i just got a mazda and its possibly same issue it says Shift Solenoid A electrical . Any advice ?
@@thelifeofleen9643 yup dealership selling it for 700 dollar.. But before you buy check the code first or change your transmission filter ang transmission fluid
My mazda 3 2005, when it's cold in the morning, jumps to gear 4 and shows AT. But after proper warm up 10-15min there is no issue. Do you think it's the same?
Thats also a common problem. I read Somewhere else here on some RUclips comments that that can be a secondary issue. But once you repla that as well, you won’t have anymore problems. I actually bought a remanufactured TCM, and relocated my TCM ( as it’s actually the heat from the transmission that kills the electronics). I installed a bracket (attached to the back of the battery box) so the replacement TCM is away from any heat.
I’m getting a P0720 with AT light on my dash. I thought I solved the code by replacing the output speed sensor, but it came back weeks later. I drive a 2011 Mazda 3 2.5L so if y’all have any advice I’d greatly appreciate it.
Where did you get you replacement tcm? The dealership wants close to $700 for a new one. I have code p0753 that popped up and changed solenoids a and b and changed the filter and oil as well but after I drove it 90mi the code came back and it wouldn't go past 3rd gear so I'm assuming I need a new tcm
Having the same problem, I decided to send it out for repair, however vehicle still having the same concern, have bench tested all the solenoids and also harnesses checks ok. Any other successful repairs besides TCM?
im having a similar problem with my 2005 mazda 3, it has a rough shift between 1st and 2nd gear. how much does it cost to get this done at a typical mechanic shop?
I have the 2007 mazda 3 with the 2.0 4 speed AT. It seems to have a different setup without a separate TCM. I think yours is a 5 speed AT. Any ideas how to fix?
My vehicle has recently thrown a P0758 code. The car drives fine but sometimes the AT does pop up. I did a transmission flush and the code never showed for about a week. Do you think the TCM at this point is the problem? Or the transmission.
Mine had same issue, installed a new tcm and AT light has gone off and now highlights the "P" for parking gear however it will not start checked starter and battery and no luck..just clicks once any advice?
i think ur tcm didnt match .i had an experience putting a tcm from online mrket same tcm number but when we install it car wont start i went to the junkyard i got lucky found one install it start right away
Hi there I have the same automatic Mazda 3 from this video the problem I have it knocks really really hard into reverse an the AT light is also on.Can it be my Tcm module as well any advice pls 🙏🏼
kapatid sa canada kc eto kung gusto mo ng tagalog may mga kaibigab akong youtuber na automotive like jeep doktor mekaniko mr yabe ..doon purong tagalog un wrong channel ka bro for english speaking viewers kc eto at majority ng viewers ko is from usa canada at australia so i need to speak in english at dito na ako canada nakabase for 17years ..sorry bro hindi eto for pinoy
I have a 2006 mazda 3 2.3 automatic and I already changed the tcm, but it wont acept the reverse and it would jump from first shift to the 4th with a loud bang. Can the Transmision be damaged?
yup ur transmission is already done if you already change the ecm and nothing happen instead it became worst thats it you need to look for a new or good raplacement tranny
Hi bro.. this was a lovely video. I have a question. I have mazda 6 2009 varient. The problem is when I drive at Hugh speed above 120km/h at times the AT tries to down shift on its own and it gives a jerk. And gives me error code P2177 " Fuel control system too lean A ". Any idea what could be the issue. Is it a gear box issue or something else.
well thats need a deep diagnostic but start checking ur datastream do we have lean or rich condition check for vacuum leak start with ur intake manifold clean ur air filter diagnose us maf /IAT clean it with maf sensor cleaning diagnose ur o2 sensor check the fluctuation of upstream and downstream ...its gonna be a heek of diagnostic bro
@@asianmechanicguy6483 thx. My friends trans seems like it slips until it warms up and then it works fine. But it will skip to 4th gear at times when cold and skip from 1 to 3rd . However I seen that AT light come on before and didn’t know if the TCM is the culprit. I have no back story as they just bought it and the seller didn’t tell them there was an issue and split with the money
Got the same at problem on my 2010 Mazda three code reader won’t bring up the codes and already changed the transmission fluid do you think changing the sensor should work
It’s a very common failure, as the heat from the transmission kills the electronics. Relocating the replacement module away from the transmission will stop the problem happening on the replacement transmission control module.
Do you happen to know who made the Sports Automatic Transmission for the Mazda 3 SP23 First generation (BK; 2003-2009) using Mazda L (L3 SVT) 4 Cylinder, 2.3 Litre engine? Is it a Jatco Transmission?
No, it depends on your engine type as well. If you have a. 2.0 litre engine, the transmission control module type will start with ” LF “. So it has to be matched to your engine.
Hey i have a 2005 mazda 3 with no engine light and no AT light. It starts fine but when i put it on drive it doesn't move at all . Can it be the TCM . Thanks
Just base in what u said i guess u had a transmission problem but ur mazda is 05 ur tcm and ecm are one from what i know.. But try a more advanced obd2 scanner there should be a code if ur car wont move
Hi randomly today my car wasn’t shifting into higher gears and then it got lower and lower and now if I start my car it doesn’t drive whatsoever when I hit the gas and I felt it shake and it went into drive and went forward but then it “disconnected” again and my engine just runs freely. Is it likely this is what broke?
@@asianmechanicguy6483 hey love the video question Mazda 3 same lights are on exactly like your car won't go pass 2nd gear and or 30 mph? So probably the tcm?
I really need help with this issue,the TCM has different part numbers for a 2007 Mazda3 does the part numbers make a difference,I looked the part number up before purchase and it said L32E 189E1B the part mumber on the old one is L34T 189E1A does this make any difference
Move the TCM to the firewall instead of putting it back onto the transmission. The heat from sitting on the transmission creates the problem for the TCM.
I have a 07 2.0 but it doesn’t have a tcm is it within the pcm and will replacing the pcm fix my problem car drives but now I can only run it like driving it for 5 minutes then it goes on AT mode and my car won’t reverse at all it would here and there but now it won’t it’s auto
@@asianmechanicguy6483 awesome. I just put it into drive today, and it only rolls. Related issue? Reverse too. It actually skips 1st and 2nd gear and goes straight into 3rd. Any issue w that?
my mazda3 2007 model when i put in the position of drive the car is jumping or kick'n and when im about to take off the gear is only upto "2" what do you think is the prob. ty
hello lakay. another lakay here but from australia. can i ask your expertise pls. mine is 2010 mazda 3 2.0. randomly engine is cutting off when you reverse especially when its cold. no dtc or any faults during scanning. any idea whats happening lakay. salamat lakay
sorry i havent try to open an 2010 mazda 3 tranny but you can always google it as even us mechanic google some mechanical parts that we are not familiar
I have a Mazda 3 I 2007 with AT light on and trouble code P0766 solenoid D stuck off already replaced transmission fluid and filter could it be the TCM?
@@asianmechanicguy6483 can you tell me why the car a Mazda 6 2006 Runs fine on a cold start up and then once it warms up after about 20-25 minute drive it will literally rip me into 3rd gear damn near getting whiplashed. This has been an ongoing issue I have been dealing with. However if I disconnect the battery for 5- 30 minutes the computer resets the check engine light And the tcs warning and the car runs fine, again within the same time frame amount. And that alleged safe mode (3rdgear) has to do with the error code P0766. I need to figure out what part needs to be replaced. I have to get the paper o'reilly's gave that has the other code. It has to do with a shift solenoid B I believe. On the overall issue I read that one of those codes could be in reflection to the other. I wasn't to fix the first cheapest code and see if the issue will resolve the code .. thx so much
@@kennethbrown8362 mazda has this tcm problem for the fast couple of years unfortunately we gamble in this kind of repair by just replacing tcm from junkyard and we had luck of it..but if uou really want to fix its not gonna be easy cuz u need to backprobe solenoid wire on the valve body going to the tcm ..check resistance while the car is warm etc...its complicated bro to be honest with you
I have a ? Hopefully you have an answer for me I have a 2007 Mazda 3 and when I take start to slow down at a stop light the car down shifts 4, 3 skips 2 goes to 1 WHY is it doing that
Goid day to you sir, i haveamazda 3 2011, AT and check engine showing, have a kick at first gear and a big kick on the reverse, where is your shop located sir
@@manuelquintos4266 my trannt issue ka bro dalhin mo sa shop na my gamit wag ung kung saan saan lang tapos ipascan mo para my starting point ka pero kung my gamit ka subukan mong palitan ung tarnny filter at fluid so meaning tatanggalin mo ung tranny pan my isa akong video na mazda 3 panoorin mo un makakatulong un bro kung gusto mong gawin at kung my knowledge ka sa automotive icheck mo narin ung resistance ng solenoid valve body mo bro baka my short na dun
Sir how are you i buy second hand mazda 3 2009 model the problem is deley shifting sometimes stock 1 or no. 2 and then i try too of engine and star again is coming normal shifting sometimes when i in road trafic i select in N after i sellect drive same problem sir
Hey brother i do have similar prblm on 2008 mazda 3 when i start driving A/T light on while driving its go away then its show me 3 rd gear thn its easily go into 4nd 5th gear sometime car not mve then i put in mannual to start driving
When i first start the car an drive it, its fine no AT light on but once i turn it off and start driving AT light comes on i clear the obd and its ok but once i turn off the engine and restart it AT light turns on is this the tcm problem or salenoid
theres a lot of complain and incident regarding transmission issue with this mazda 3 and mostly the culprit is the TCM..l'll go with the TCM right away...
I have a 2011 Mazda 3 with a 2.0 Runs and shifts fine until AT light comes on, then won't go past 3rd gear until I cut car off and back on. Then drives fine again until light comes on. Do you think it's the same issue?
theres a big chance you had a bad tcm like mine but before you do any repair scan ur car for codes after that change ur tranny filter ang tranny fluid most of the time its only clogged tranny filter
I have my 2009 Mazda 3 it has a similar problem sometimes it works fine and other times it stays in third gear with the AT light on I put a scanner in it and I got the code u0101 sera la TMC?
I have a 2009 Mazda 3. Car went out while driving. When I turn the car on, it just revs and stays running in any gear if I let off the clutch. I still need to use the clutch to put it in to any gear. Someone over the phone thought that sounded out of the norm and said to look in to bleeding my clutch. My fluid was damn near empty when I checked it. Took more than half a bottle to fill.
Sir bka me alam kyo sa mazda premacy imported. Ang problem nya nahihirap umakyat. Ngbliblink un hold button kpg pgkastart at ilan mins lalabas na at blink hold button. Pinascan ko p0730 pno po kya ayusin? Salamat.
@@IsaiahFelix mahabang diagnostic yan kung nandito ka sana sa lugar ko pwede kung I duplicate ung nangyayari depende na sa mekaniko na titingin dyan dapat mayrun silang advanced obd2 scanner para hindi huhulaan lang. Kung ako ang gagawa marami akong ichecheck dyan wiring resistance solenoid resistance idodown ko ung transmission pan ichecheck ko kung my metal parts. Ichecheck ko ung tranny fluid ung amoy ung color ung level.. Ichecheck kung nagkakaproblema lang sya kung nakawarm up na marami bro hundreds scenario ang pwedeng mangyari dyan so kailangan mo ng good mechanic...
@@asianmechanicguy6483 sige po maraming salamat po sa advice. Ipapacheck ko nlng po isa isa mga possible na faults sa transmission. Gaya ng sabi nyo hehehe
kailangang icheck ung sensor na un pero kung walang pyesa dyan un ang problema ..pero pansamantala magpalit ka muna ng tranny fluid at filter my isa akong video ng mazda 3 transmission fluid at filter change panoorin m o un bro hopefully clogged filter lang problema mo ung mga pag check kc ng mga sensor kailangan professional or experience mechanic ang gagawa nun.
Sir ask ko lang po about sa Mazda 3 ko. Ganyan din po problem nya pag nagshift 2nd gear agad and may AT sign at erratic po yung andar nya. Nascan ko na po error code po P0758 Shift solenoid B electrical po ang code. Is it the TCM po ba or the solenoid itself? Thanks po
@@eunicebautista5976 ate mukhang tcm nga ang sira ng car mo pero ang way mo kc sa pag ayos nyan ay idodown ko muna ung tranny pan palitan ko ing tranny filter at lagyan ko ng new fluid at the same time check ko ung resistance ng mga solenoid valve body then after that irun ko ung car sa highway kung ayaw parin thats the time tcm ang papalitan ko.. Pero kung wala kang knowledge sa mga repairs palitan mo na agad ung tcm mo medyo mahal ngalang
scan mo muna bro dun magkakaroon ka ng starting point kung ano nangyayari sa car mo but initial diagnose base sa sinabi mo mukhang my transmission issue ka
Scan ur car for codes thats the first step that u need to do if you dont have scanner find one that has if you cant find one u can try to other direction like dropping ur tranny pan put a new tranny fluid and filter
sir pa help naman po same po issue ng mazda 3 nmin 2004 05 model po pag una andar ok sya nag shift pa sya 1 2 3 4 bigla sya susumpong sir na once shift na sa d agad sya nasa 4gear sir.. history po ng mazda nasaksak po pabaliktad yung battery sir.. sana. ma help nio po ako sir..
check the codes first before anything else if only happen when the car is already hot it might be the solenoid ur tcm and ur case ur pcm is also ur tcm if im not mistaken as i dont know what year is your car
That's the second thing I changed on my daughter's 08 mazda3 2.3l . I changed tge sensor it showed on my reader first (output shaft sensor). Fixed it..costly, but fixed (new TCM).
So the TCM fixed the issue?
I have a similar problem with my 2007 Mazda 5. This is a brilliant video. Thank you!!
Thanks for watching!
Thank you for showing how to remove the computer hookups - I'm not skilled in car repair at all, and I got hung up at that part. Tons of other videos skip this! THANK YOU!
Glad it helped
Wow I had this problem and the mechanic told me I needed a new transmission
this is one of the common problem of mazda 3
He is either an incompetent mechanic, or looking to rip you off. Either way, I’d be looking for a new mechanic!
Excellent video- Bad TCM is common transmission problem with Mazda vehicles
yup indeed its the most common problem of this car
This video will be very helpful to me cus I’m facing same situation with same model.
Thanks a million times.
Glad it helped
so did it work? changing the TCM helped?
You need to make more videos. This is one of the best DIY videos I've ever seen. You get right to work not much jabber.
More to come!
Thank you sir! Just saved a lot of money avoiding a shop.
Glad to help
@@asianmechanicguy6483 okay I just got my module back and installed it and it’s still doing the same thing. If that module is fixed is there something else I need to do? I figured all errors would be cleared out since the battery has been out for a week. Help please. Thanks.
Excellent video. TCM is always problem with Mazda vehicles...
thank u and please keep watching my other videos
For the automatic tranny , yes , but not on a manual tranny...
Wow I really love your video nice I work with the company in jamaica
Thanks bud. Saved me lots of time!
Glad it helped
Thanks for the video my friend! I have a 2006 mazda 3 everything works fine except when I put it in reverse it takes like 2 minutes to go in reverse.. do you think it's the same problem? Any ideas anyone? Muchas gracias
Iv seen this a lot actually lol. Its a manual right? The manual actually tells you, if you havs this problem, to put it in neutral and release the clutch and try again. Its a very common problem from what iv heard and i get the same problem. The only thing that helps is putting it in neutral and releasing the clutch and then trying again
Good day man. Do you think you can help me out.
I've got the following issue.
I have a 2006 mazda 3 automatic
The AT icon lights up after about 10 mins of driving
The car is not shifting properly, the shifts are a bit delayed and they become hard shifts after the AT lights up. Also the gears dont come down from 4th or 3rd unless I practically stop. The gears in M mode are not displaying either.
Thank you in advance!
get scan so you will have an starting point
Same problem in my Mazda 6. Thank you!
youre welcome please keep watching new car repair videos
@@asianmechanicguy6483 hello, is this piece expensive i just got a mazda and its possibly same issue it says Shift Solenoid A electrical . Any advice ?
@@thelifeofleen9643 yup dealership selling it for 700 dollar.. But before you buy check the code first or change your transmission filter ang transmission fluid
@@thelifeofleen9643 any update on transmission problem ?... and any possible fix
What sillcan did you use?
good job! however, if it's a common issue in these cars, i would 've bought a new one to install.
yup its a common problem of this car
Tcm fixed my daughter's 08 mazda3 with the 2.3l 5spd auto. New was $$$, but no issue afterwards.
Your advice worked wonders. Thank you
Glad it helped!
My mazda 3 2005, when it's cold in the morning, jumps to gear 4 and shows AT. But after proper warm up 10-15min there is no issue. Do you think it's the same?
im pretty sure its the tcm but still u need to scan it for codes or diagnose it more u never know
What code was the car giving? I am having transmission problems, but no codes for transmission.
Hi.some company rebuilt my tcm but still have have code p0791 ,intermidiate shaft speed sensor????
Thats also a common problem. I read Somewhere else here on some RUclips comments that that can be a secondary issue. But once you repla that as well, you won’t have anymore problems. I actually bought a remanufactured TCM, and relocated my TCM ( as it’s actually the heat from the transmission that kills the electronics). I installed a bracket (attached to the back of the battery box) so the replacement TCM is away from any heat.
I’m getting a P0720 with AT light on my dash. I thought I solved the code by replacing the output speed sensor, but it came back weeks later. I drive a 2011 Mazda 3 2.5L so if y’all have any advice I’d greatly appreciate it.
Were you able to fix it?
Where did you get you replacement tcm? The dealership wants close to $700 for a new one. I have code p0753 that popped up and changed solenoids a and b and changed the filter and oil as well but after I drove it 90mi the code came back and it wouldn't go past 3rd gear so I'm assuming I need a new tcm
Junkyard bro
Try an Automotive electrician, he should have industry contacts with people who do the TCM module repairs.
Did you had to program the TCM before installing?
no just install right away
Thank you for the video, just wondering what kind of silicone did you use
sorry this video is been a while but a bought that silicone paste at canadian tire i think thats for the window caulking
Having the same problem, I decided to send it out for repair, however vehicle still having the same concern, have bench tested all the solenoids and also harnesses checks ok. Any other successful repairs besides TCM?
Have you tried the transmission speed sensor?
im having a similar problem with my 2005 mazda 3, it has a rough shift between 1st and 2nd gear. how much does it cost to get this done at a typical mechanic shop?
$700 for the remanufatured one flagship one plus $100 labour if i do it
I have the 2007 mazda 3 with the 2.0 4 speed AT. It seems to have a different setup without a separate TCM. I think yours is a 5 speed AT. Any ideas how to fix?
replace ur tcm send it to flagship one they will rebuild ur tcm
My vehicle has recently thrown a P0758 code. The car drives fine but sometimes the AT does pop up. I did a transmission flush and the code never showed for about a week. Do you think the TCM at this point is the problem? Or the transmission.
Mine had same issue, installed a new tcm and AT light has gone off and now highlights the "P" for parking gear however it will not start checked starter and battery and no luck..just clicks once any advice?
i think ur tcm didnt match .i had an experience putting a tcm from online mrket same tcm number but when we install it car wont start i went to the junkyard i got lucky found one install it start right away
Hi there I have the same automatic Mazda 3 from this video the problem I have it knocks really really hard into reverse an the AT light is also on.Can it be my Tcm module as well any advice pls 🙏🏼
yup thats TCM
Thanks so much will definitely try to source a new one.
kuya its ok mag tagalog mas maraming makakaintindi at mas malinaw cguro pag nag explain ka
kapatid sa canada kc eto kung gusto mo ng tagalog may mga kaibigab akong youtuber na automotive like jeep doktor mekaniko mr yabe ..doon purong tagalog un wrong channel ka bro for english speaking viewers kc eto at majority ng viewers ko is from usa canada at australia so i need to speak in english at dito na ako canada nakabase for 17years ..sorry bro hindi eto for pinoy
I have a 2006 mazda 3 2.3 automatic and I already changed the tcm, but it wont acept the reverse and it would jump from first shift to the 4th with a loud bang. Can the Transmision be damaged?
yup ur transmission is already done if you already change the ecm and nothing happen instead it became worst thats it you need to look for a new or good raplacement tranny
Great job my friend
Thank you 👍
Hi bro.. this was a lovely video. I have a question. I have mazda 6 2009 varient. The problem is when I drive at Hugh speed above 120km/h at times the AT tries to down shift on its own and it gives a jerk. And gives me error code P2177 " Fuel control system too lean A ". Any idea what could be the issue. Is it a gear box issue or something else.
well thats need a deep diagnostic but start checking ur datastream do we have lean or rich condition check for vacuum leak start with ur intake manifold clean ur air filter diagnose us maf /IAT clean it with maf sensor cleaning diagnose ur o2 sensor check the fluctuation of upstream and downstream ...its gonna be a heek of diagnostic bro
Great stuff thanks mate from Australia.
Do you have video for changing solanoid etc on Mazda 3?
none so far but if ever ill post it right away
What was the condition that caused u to replace the TCM? Slipping when cold? Not shifting?
Blinkingr AT stuck on 3rd gear and has a transmission code
@@asianmechanicguy6483 thx. My friends trans seems like it slips until it warms up and then it works fine. But it will skip to 4th gear at times when cold and skip from 1 to 3rd . However I seen that AT light come on before and didn’t know if the TCM is the culprit. I have no back story as they just bought it and the seller didn’t tell them there was an issue and split with the money
Got the same at problem on my 2010 Mazda three code reader won’t bring up the codes and already changed the transmission fluid do you think changing the sensor should work
try this approach thers a big chance u had a bad tcm
It’s a very common failure, as the heat from the transmission kills the electronics. Relocating the replacement module away from the transmission will stop the problem happening on the replacement transmission control module.
did you solve this?
Do you happen to know who made the
Sports Automatic Transmission for the Mazda 3 SP23 First generation (BK; 2003-2009) using Mazda L (L3 SVT) 4 Cylinder, 2.3 Litre engine? Is it a Jatco Transmission?
Sorry no
Can’t believe you skipped the hardest part. Show us how you got that 3rd bolt out. Wow!
i dont have tiny camera that fit on the location of 3rd bolt
Yea that bolt pissed me off lol
how is the DCT for my madza 3 2007 model i need to buy it
Are tcm’s compatible? E.G can I replace a sp23 07 tcm with 2010 sp25 tcm
sorry this is only for 06-07 mazda 3 tcm replacement first 4 letters in ur tcm should be thesame in order to work or to interexchange ..
No, it depends on your engine type as well. If you have a. 2.0 litre engine, the transmission control module type will start with ” LF “. So it has to be matched to your engine.
Hey i have a 2005 mazda 3 with no engine light and no AT light. It starts fine but when i put it on drive it doesn't move at all . Can it be the TCM . Thanks
Just base in what u said i guess u had a transmission problem but ur mazda is 05 ur tcm and ecm are one from what i know.. But try a more advanced obd2 scanner there should be a code if ur car wont move
Ayos pare!
Hi randomly today my car wasn’t shifting into higher gears and then it got lower and lower and now if I start my car it doesn’t drive whatsoever when I hit the gas and I felt it shake and it went into drive and went forward but then it “disconnected” again and my engine just runs freely. Is it likely this is what broke?
mostly likely u had a bad tcm ..Sometimes cleaning the connector might work for a bit but then u need to replaced the TCM still
But means check the liquid of transmission first? What about its look red but it's full?
Thanks for sharing. what's the price of selenoi
would this cause a Mazda 3 2007 to not shift any higher the 4 gear?
yup if your car wont shift to any gear its stuck on only in one gear let say 3rd gear then theres a big chance u had a bad tcm
@@asianmechanicguy6483 hey I have 2010 Mazda 3 I have the AT light on and when I drive my car it switch gear to manual. I have a Automatica
@@asianmechanicguy6483 hey love the video question Mazda 3 same lights are on exactly like your car won't go pass 2nd gear and or 30 mph? So probably the tcm?
@@jimmyj4395 most likely tcm which is very common to mazda 3
@@asianmechanicguy6483 I figured that thanks bro
I really need help with this issue,the TCM has different part numbers for a 2007 Mazda3 does the part numbers make a difference,I looked the part number up before purchase and it said L32E 189E1B the part mumber on the old one is L34T 189E1A does this make any difference
use tcm with thesame part number
Move the TCM to the firewall instead of putting it back onto the transmission. The heat from sitting on the transmission creates the problem for the TCM.
I have a 07 2.0 but it doesn’t have a tcm is it within the pcm and will replacing the pcm fix my problem car drives but now I can only run it like driving it for 5 minutes then it goes on AT mode and my car won’t reverse at all it would here and there but now it won’t it’s auto
I have the 2007 mazda 3 with the 2.0 4 speed AT. Were you ever able to get it fixed?
Boss Pati ba solenoid pinalitan mo?
Any problems going into reverse?? (I just started the video) this just my main question
both forward and reverse car jerks
@@asianmechanicguy6483 awesome. I just put it into drive today, and it only rolls. Related issue? Reverse too. It actually skips 1st and 2nd gear and goes straight into 3rd. Any issue w that?
I changed the TCM but still changing gears rough but it goes. Just don’t show when it’s in drive, any clue what it might be?
check for codes
When was the last time the transmission fluid was changed, and the transmission filter as well??
I have a 2007 speed 3 I just broke a cv axle and now when I put it in gear it’s making a grinding noise.. do u think u might kno tha issue?
what did you broke the gear of cv axle or the rubber boot is tear
Hi I have a 2006 and it won’t drive uphill. Can this be the same transmission issue?
it might bro but first get ur car scanned
my mazda3 2007 model when i put in the position of drive the car is jumping or kick'n and when im about to take off the gear is only upto "2" what do you think is the prob. ty
theres a problem on ur tranny for sure the best way that u need to do is scan your car with a good obd2 scanner
When I put in drive N and P blink. Could this be what I need to replace ?
Thank you
most likey yup its a bad tcm its commom to this mazda 3
@@asianmechanicguy6483 thank you
hello lakay. another lakay here but from australia. can i ask your expertise pls. mine is 2010 mazda 3 2.0. randomly engine is cutting off when you reverse especially when its cold. no dtc or any faults during scanning. any idea whats happening lakay. salamat lakay
mahirap yan bro kailangan personal kung makita ung car pweding fuel issue pweding electrical issue pweding sensor issue
I have a 2007 mazda 6 2.0 and need a Transmsition control unit .can you help.Unable to source one in my country
go to dealership if no junkyard available in ur area
Did you get firmware update on the tcm?
plug in play but make sure it has the same code lettres and numbers
@@asianmechanicguy6483 what is plug and play?
@@boondocks1able literally the sentence
Hello I have a question I have a 2010 Mazda 3 with a code to replace shift selenoid A so which one is A.
sorry i havent try to open an 2010 mazda 3 tranny but you can always google it as even us mechanic google some mechanical parts that we are not familiar
I have a Mazda 3 I 2007 with AT light on and trouble code P0766 solenoid D stuck off already replaced transmission fluid and filter could it be the TCM?
yup bro theres a big chance its the tcm
@@asianmechanicguy6483 can you tell me why the car a Mazda 6 2006 Runs fine on a cold start up and then once it warms up after about 20-25 minute drive it will literally rip me into 3rd gear damn near getting whiplashed. This has been an ongoing issue I have been dealing with. However if I disconnect the battery for 5- 30 minutes the computer resets the check engine light And the tcs warning and the car runs fine, again within the same time frame amount. And that alleged safe mode (3rdgear) has to do with the error code P0766. I need to figure out what part needs to be replaced. I have to get the paper o'reilly's gave that has the other code. It has to do with a shift solenoid B I believe. On the overall issue I read that one of those codes could be in reflection to the other. I wasn't to fix the first cheapest code and see if the issue will resolve the code .. thx so much
@@kennethbrown8362 mazda has this tcm problem for the fast couple of years unfortunately we gamble in this kind of repair by just replacing tcm from junkyard and we had luck of it..but if uou really want to fix its not gonna be easy cuz u need to backprobe solenoid wire on the valve body going to the tcm ..check resistance while the car is warm etc...its complicated bro to be honest with you
Cant you relocate the TCM away from the transmission so it doesn't overheat and destroy the components inside it again?
yes u can u can put it on the fire wall using ziptie
Trying using something like zip ties. something like this I have see on a RUclips video. I just replaced my tcm works good.
Hello po! parehas po ba ang TCM ng model mazda 3 2010 TIA
not sure bro
I have a ? Hopefully you have an answer for me I have a 2007 Mazda 3 and when I take start to slow down at a stop light the car down shifts 4, 3 skips 2 goes to 1 WHY is it doing that
go a a mechanic get it scan i can not guess whats going on into ur car but most likely you had a transmission issue
Goid day to you sir, i haveamazda 3 2011, AT and check engine showing, have a kick at first gear and a big kick on the reverse, where is your shop located sir
vancouver bc
Rhaswin's Garage oh too far from the Philippines, anyways do you have any suggestions sir what could be the solution for my car
@@manuelquintos4266 my trannt issue ka bro dalhin mo sa shop na my gamit wag ung kung saan saan lang tapos ipascan mo para my starting point ka pero kung my gamit ka subukan mong palitan ung tarnny filter at fluid so meaning tatanggalin mo ung tranny pan my isa akong video na mazda 3 panoorin mo un makakatulong un bro kung gusto mong gawin at kung my knowledge ka sa automotive icheck mo narin ung resistance ng solenoid valve body mo bro baka my short na dun
Rhaswin's Garage maraming salamat sir
Did the problem come back after a while po? Or did it completely fix the problem po?
the car is fix and i sold the car long time ago this is one of the common issue of mazda 3 but its an easy fix as long u got the right tcm
Rhaswin's Garage thank you po
Do you know if my car don’t gear in reverse and the AT light is on can that be the tcm ?
scan it for code that way u had an starting point
what was it. my car won’t go into reverse either and third gear shifts really hard
My Mazda is showing P0763,solonoid C electric problem...so what should I do..
bring it to a mechanic
I have a 2010 with 120 thousand should I do something before it goes bad
place ur tcm to ur wirewall just make ur own bracket or zip tie it
I got a 2009 Mazda 5 ….do u know who can fix the tcm
buy a new one from the dealership its around $800 Cad
@@asianmechanicguy6483 too much…u don’t know nobody that can fix it
Thank you brother
Any time
Hello, what kind of paste is that at the bottom of the tcm? Where can I get it? Thanks
silicone that i bought it from canadian tire
You can get an expoy resin as well.
Sir how are you i buy second hand mazda 3 2009 model the problem is deley shifting sometimes stock 1 or no. 2 and then i try too of engine and star again is coming normal shifting sometimes when i in road trafic i select in N after i sellect drive same problem sir
scan ur car for codes
Hey brother i do have similar prblm on 2008 mazda 3 when i start driving A/T light on while driving its go away then its show me 3 rd gear thn its easily go into 4nd 5th gear sometime car not mve then i put in mannual to start driving
the first thing that i should do is change the filter and transmission fluid
Speed turbine sensor is bad location top of Transmission.
When i first start the car an drive it, its fine no AT light on but once i turn it off and start driving AT light comes on i clear the obd and its ok but once i turn off the engine and restart it AT light turns on is this the tcm problem or salenoid
theres a lot of complain and incident regarding transmission issue with this mazda 3 and mostly the culprit is the TCM..l'll go with the TCM right away...
@@asianmechanicguy6483 salamat
Very good knowledge
thank you
I have a 2011 Mazda 3 with a 2.0 Runs and shifts fine until AT light comes on, then won't go past 3rd gear until I cut car off and back on. Then drives fine again until light comes on. Do you think it's the same issue?
theres a big chance you had a bad tcm like mine but before you do any repair scan ur car for codes after that change ur tranny filter ang tranny fluid most of the time its only clogged tranny filter
What size bolt did you use?
10mm i think
I have The same problem ,but a turn the off and bringer back the light is gone
sorry what was ur question
I have my 2009 Mazda 3 it has a similar problem sometimes it works fine and other times it stays in third gear with the AT light on I put a scanner in it and I got the code u0101 sera la TMC?
no communication codes try no clean connection first
Clean all the connectors and it's still the same. The strange thing is that sometimes the AT code comes on with the traction control light
@@pablobarajas5662 bad tcm my friend very common to mazda 3
Thanks I'll get it and see what happens
Where did you buy the replacement po?
from the junkyard
Sir ano po yung silicone na ginamit nyo para insulation sa tcm as heat insulator. Salamat sir
High temperature rtv silicone from Canadian tire
What was that paste in the back of computer????
its a silicone sealant from canadian tire
I hv nearly exact same issue...AT is lit and when put in drive . Reads 3rd gear..thx ..
I need Mazda MPV06 transmission computer or do I get to it I am asking you
dealership
I have a 2009 Mazda 3. Car went out while driving. When I turn the car on, it just revs and stays running in any gear if I let off the clutch. I still need to use the clutch to put it in to any gear. Someone over the phone thought that sounded out of the norm and said to look in to bleeding my clutch. My fluid was damn near empty when I checked it. Took more than half a bottle to fill.
Bro do u have an extra module i need one and my junk yard got raided for those things and i aint paying 600!! At a dealer, junk yard price 14 dollars.
sorry bro i got no more im trying to fix the old one i did open studying it but until now no luck
Ohh damn well good luck then
Sir bka me alam kyo sa mazda premacy imported. Ang problem nya nahihirap umakyat. Ngbliblink un hold button kpg pgkastart at ilan mins lalabas na at blink hold button. Pinascan ko p0730 pno po kya ayusin? Salamat.
my big chance na tcm yan try mong linisin ung mga connector papuntang tcm
@@asianmechanicguy6483 sige po. TCM po ung sa likod ba ng sterio? Sbi nila same dw un mazda premacy sir sa mazda 626.
@@asianmechanicguy6483 sir sanga po pala mahirap po kasi umakyat ung mazda, tcm pdn po ba un? Pra alam ko po mga ipapacheck ko. Salamat po.
@@IsaiahFelix mahabang diagnostic yan kung nandito ka sana sa lugar ko pwede kung I duplicate ung nangyayari depende na sa mekaniko na titingin dyan dapat mayrun silang advanced obd2 scanner para hindi huhulaan lang. Kung ako ang gagawa marami akong ichecheck dyan wiring resistance solenoid resistance idodown ko ung transmission pan ichecheck ko kung my metal parts. Ichecheck ko ung tranny fluid ung amoy ung color ung level.. Ichecheck kung nagkakaproblema lang sya kung nakawarm up na marami bro hundreds scenario ang pwedeng mangyari dyan so kailangan mo ng good mechanic...
@@asianmechanicguy6483 sige po maraming salamat po sa advice. Ipapacheck ko nlng po isa isa mga possible na faults sa transmission. Gaya ng sabi nyo hehehe
sir ngpa scan po aq ang lumabas po715 which is turbine shaft speed sensor.. need n po ba agad ireplace un? wla p kc mblhan pyesa..
kailangang icheck ung sensor na un pero kung walang pyesa dyan un ang problema ..pero pansamantala magpalit ka muna ng tranny fluid at filter my isa akong video ng mazda 3 transmission fluid at filter change panoorin m o un bro hopefully clogged filter lang problema mo ung mga pag check kc ng mga sensor kailangan professional or experience mechanic ang gagawa nun.
Wait so we don’t have to reprogram the used one?
plug and play
IDOL MAY TCM DIN BA UNG 2003/2004 MODEL MAZDA 3
mayrun bro depende lang sa design sometimes 2 in 1 meaning ung ecm mo nandun narin tcm mo
@@asianmechanicguy6483 thanks po
goodmorning sir . may TCM rin ba ang Mazda 3 2005 model?
mayrun din mas malaki nga lang compare sa 07 mazda 3
@@asianmechanicguy6483 ok sir, how about yung location ng tcm same rin po ba?
No iba ang location nya sa experience ko ung ecm mo ay un din ang tcm mo
How much is the TCM?
around $1200 cad rebulid from flagship one
Sir ask ko lang po about sa Mazda 3 ko. Ganyan din po problem nya pag nagshift 2nd gear agad and may AT sign at erratic po yung andar nya. Nascan ko na po error code po P0758 Shift solenoid B electrical po ang code. Is it the TCM po ba or the solenoid itself? Thanks po
Umaandar naman po sya sa drive and reverse. Kaya lang nagsheshake po sya ng malakas pag di nakatapak sa gas pedal.
Btw Mazda 3 2006 model po sya
@@eunicebautista5976 ate mukhang tcm nga ang sira ng car mo pero ang way mo kc sa pag ayos nyan ay idodown ko muna ung tranny pan palitan ko ing tranny filter at lagyan ko ng new fluid at the same time check ko ung resistance ng mga solenoid valve body then after that irun ko ung car sa highway kung ayaw parin thats the time tcm ang papalitan ko.. Pero kung wala kang knowledge sa mga repairs palitan mo na agad ung tcm mo medyo mahal ngalang
Pano po ba sir ang pag check ng resistance ng solenoid?
watch my other videos para sa pag check mg solenoid resistance
sir ask lang po ung m3 ko bigla nagddownshift pag nsa 4 kna ang hirap umarangkada and bigla nln bababa sa 2 at mag wild n tunog ng makina po..
scan mo muna bro dun magkakaroon ka ng starting point kung ano nangyayari sa car mo but initial diagnose base sa sinabi mo mukhang my transmission issue ka
Bro, nag rerepair ka ng TCM? 2008 Mazda 5
no bro
2005 model how to repair transmision
Scan ur car for codes thats the first step that u need to do if you dont have scanner find one that has if you cant find one u can try to other direction like dropping ur tranny pan put a new tranny fluid and filter
paps? saan ba may benta ng tcm ng mazda 3 2.0 2007? yong surplus paps pls mindano kami paps
Sorry bro dko alam sa canada kc ako
@@asianmechanicguy6483 sir? hinanap ko TCM ko exact location sa video mo. bakit po wala akong TCM?
what year ba ung sau bro pag late model ka 05 below i think ung tcm at ecm are 2 in 1 na
Sir, saan ka po ba sa mindanao? Mindanao rin kasi loc ko. May hinahanap din ako pyesa pra sa mazda ko.
@@kathleenlim380 sis mukhang wrong channel ka nasa Canada ako at sa pinas taga Pangasinan naman ako di pa ako nakatapak sa Mindanao sister
sir pa help naman po same po issue ng mazda 3 nmin 2004 05 model po pag una andar ok sya nag shift pa sya 1 2 3 4 bigla sya susumpong sir na once shift na sa d agad sya nasa 4gear sir.. history po ng mazda nasaksak po pabaliktad yung battery sir.. sana. ma help nio po ako sir..
una po nung gagawin scan nu at icheck kung my code kc kung my nasunog na solenoid dapat magkakaroon ng code yan
@@asianmechanicguy6483 cge po sir..
I have a Mazda 3 2.0L and I have transmission problem where it won’t sift in to 4th gear and just revs and mine doesent have TCM anyone know problem?
check the codes first before anything else if only happen when the car is already hot it might be the solenoid ur tcm and ur case ur pcm is also ur tcm if im not mistaken as i dont know what year is your car