I believe that before we even go so deep into the control modules, the very basic troubleshooting checks should be the electrical connectors (bad and oxidized electrical contacts), which can cause delayed or failed shift solenoid operation. Always follow the repair flowchart from the most economical then work your way down to the more costly ones. Without Prejudice to anyone, this is my way of troubleshooting any repairs. Thanks for reading.
My ford focus transmission has been giving me problems lately. Won’t shift into gears , stays in certain gears , doesn’t accelerate correctly, won’t go in reverse. When i took it to the shop they said it was probably the transmission range sensor so i replaced that, had same issues. Replaced the B actuator next it worked for a couple hundred miles then same issue. Replaced the other actuator and it only worked 100 miles or so then same issue. Should i replace the TCM next? I did all the cheaper fixes first but still having issues and don’t know what to do.
Thank you I’ve been having transmission problems with my 2007 Nissan Maxima SE not shifting and not running good but definitely there’s a problem with the TCM on my dash I noticed that when I shift the gears into Park or Neutral not showing on my dash but the Reverse and Drive are showing unbelievable how something like this will not let your vehicle run good and transmission performance horrible.
I have 2013 charger that had a front wiring harness replacement. It shifted fine going over to the garage, harness was replaced wouldn't shift right after that. Codes up the ying yang clear the codes and sometimes it shift's sometimes no it wont shift right. The garage says its a speed sensor 1900 dollars to fix , i think someone is full of it. Like i said shifted fine before a harness replacement, something doesn't smell right , i could be wrong but though
Hi love the video my 2009 Acura tl sh/awd self diagnosis within the car show TCM error The trans when it’s warm up down shifts and goes back into the gear it was in before the down shift. It’s very annoying and no one can figure it out
My truck is a 2009 Peterbilt 335, in the mornings I turn it on and it drives great, I can drive it all day without any problem, but without turning it off, if I turn it off that's when the problem starts and it no longer wants to drive anywhere, he changed the switch, internal transmission ignition switch, speed sensors and the internal wiring of the transmission and the issue does not disappear, do you think it is the TCM?
Hi i need your advise about my scion xb 2005 i changed engine but my transmission wont move my car i put it on reverse and drive but wont move turns on good ?
I have a 2015 Nissan quest and it was crushed on the side of the drivers side. It had a problem when I got it back after repaired that as you were driving it will pull to the left and when you would let it go it would pull to the right or vice versa already exhausted most of my savings in this problem by changing parts that were not it took it out of the shop and changed all of the motor from the motor thinking that that would be a problem and pinion we changed it and we changed the control arms as well Also the part for the little boots which I cannot remember the name of it that got replaced as well because it was worn out. Here’s the that it’s still doing the same thing?
I have a 2013 gmc Yukon xl slt recently my transmission sounds awful in Reverse and in Drive, sounds fine in Park and neutral. When sitting at a red light I have to switch into D or N but when placing back in D in gives me a big buck then goes. Would this possibly be the TCM? Or bigger problem? Thank you for any help in this matter. We use this for my daughter with special needs. Need to fix quickly.
I want to know what could cause ine day to be fine at shifting and the next day I only have 1st. gear no shifting to 2nd. third or forth . 4L60 4x4 trans from a 96 sonoma highrider . ?
im going to buy a ecm from ebay can i go to the dealer and get the part number on my current ecm or do i have to pull it out the dash and get it from there i just don't want to do the job twice
I have a 2017 mitsubishi lancer with a P2719 code. I've read about people replacing valves, valve body, fluid filters etc.. then having the same issue until thier TCM or ECU software was updated from Mitsubishi. Any insight into this? I found1 video on RUclips but it was in a different language unfortunately, so it didn't help me much.
Hi pls suggest what to do i have this error message p0606 component y3/8n4 fully integrated transmission control unit is faulty.. can i service or have to replace the sparepart
There is a problem with the Rx350 2007 transmission. When the engine is cold, it cannot move forward, but reverse runs smoothly, and after the engine heats up, it can move forward without any major problems. What is the problem?
I am getting a P0717 Code for my trans, which occurred after I power washed the engine bay. The trans is sticking in first gear, clunking at a stop or when I let my foot off the brake after coming to a stop. I am receiving a "Service Transmission" indication on the dash, and a "Service Stabilitrak and Traction Control," too. The TCM is located on top of the trans and connected to the gear shift selector. Everyone says my trans is done (at 200K miles), but I don't believe it because serviced the trans when required so, I don't think its the trans but the TCM. I have a 2014 Chevrolet Cruze Turbo Diesel with at AF40-6 6-spd AT trans. HELP! I don't want to replace the transmission, especially at $6K.. NO WAY!
I have a 03 yukon 5.3 and its tbrowing no codes but it wont shift. Put in drive an never shifts it pulls of strong in drive and reverse abd wi take off in all gears if you do it manualy. Just put the transmission in. The old transmission wouldn't go to 3rd or 4th now this one won't shift at all
Not getting limp mode but i recieve transmission limitied function hooked up to an obd and this was the only thing that appeared could this cause the issue
I'm thinking about buying a used TCM from ebay. How would I go about reprogramming it? Its for my son's car so I'm not wanting to spend the $200.00 on a new one if I don't have to. Please and Thank You!
Hey guys, I’ve had a similar issue with my van (2001) 3.3litr v6 I noticed that when I was driving, the van was stuttering and it seemed like it didn’t want to drive nor break and I was only going about 35-45km. I pulled to the side stoped and turned it off for about 5 mins then I started it drove normal for the first few seconds then it was stuttering again and wouldn’t go past 20-25km so then I turned it off and parked it, after leaving it turned off for awhile I started it and it cranked but then turned completely off in about 20 seconds , then the engine was stuttering and it seemed like it wanted to go but kept on stuttering the muffler was giving out some weird sounds…maybe bad fuel pump? Transmission gone bad ? ….if anyone can point me in the right direction on what to do….I would grateful appreciate it
My truck was doing fine up until I used a hypertech tuner on it. Now it's acting like the torque converter is going out. I've already turned it back to the stock program. 2013 Chevy 2500 HD 6.O Gas motor 4x4
I HAVE A 2014 6L90 THAT I JUST REBUILD AND NOW IT DRIVES AND CHANGES GEARS GOOD BUT AFTER A WHILE OF DRIVING WHEN I STOP IT WILL STOP PULLING IN FORWARD AND REVERSE WHEN I TURN THE VAN OFF AND BACK ON IT DRIVES CORRECTLY UNTIL I STOP PLEASE HELP
Why does my transmission or breaks don’t know lock on drive at about 25mph Honda ridgline2008 drives in gear 1 but not drive or gear 2 car just slams on breaks and stop works again with a on and off. Reverse not working neutral pulls forward
Hey I have a gxp too and got a p0070 code. Did you have the same? It’s been going into limp mode lately. Going to take it into the shop this week. Also, how many km you have on yours? Mines a 2008 G6 GXP
Same issues I changed the ecm but it’s running really rough at park it idles low seems to be at 600 then in drive jumps up crazy high & seems as if it’s going to stall out I have a 06 gxp Grand Prix
On my 2011chevy silverado lt 4.8 ,transmission work, for about 20 minutes and then it will not go forward or reverse, but if I turn off the key n restart it it will run again, tell I stop at a like, can someone tell me what to look at ,no cord
I have a 2000 Chrysler town and country. Wouldn’t start on me. Once we got it towed to the house it turned on but if I wanted to shift gears there’s no telling which one I’m choosing There’s also an obvious vibration under the hood. What could be the problem? No check engine light too
I have a 2012 Elantra, transmission issues, changed the pump, some clutches and valve body! Now it drives but great the first time it goes through the gears but starts to shift hard and gets progressively worse until it’s reset, but does it again the very next drive. Please help
The serial numbers are on your TCM. It’s not hard to locate or snap a pic of. I’m going through the process of fixing mine now that I’ve replaced both actuators and the range sensor but have same transmission problems. It’s a pain in the ass. Screw ford they sell shit cars
@@addisonsigley8033The focus was so shit that they don’t even make cars anymore 😂(besides the mustang) Their suvs and trucks are good though. My shitbox 2014 focus made me want to drive off a cliff. I have a 2017 Expedition EL now and its a beast and super reliable.. The focus really killed their car reputation.
I have an automatic 2010 mazda 3 which started jerking when shifting through the gears. i changed the ATF and it still continued and later on the car lost power while i was driving and it wouldnt engage any gear. The mechanic says i need to change my gear box and tcm. While all this was happening i never had any warning lights come on. Any thoughts or comments ?
Great tutorial...My 2010 Impala 3.5L has been having intermittent No Crank No Start issues the Usually begin with a Goofy Start (Starts after Returning from Crank Position to On Position) and soon after, warning Chimes, Service Everything Messages, Gauges go Crazy back and forth, Door Locks on/Off Constantly, Shifts get Rough BUt not Limp Mode and sometimes it actually goes into limp mode.. Once I shut it off for a while a No Crank No Start will happen... Most of the times I can Disconnect Battery and then it gets back to normal.. Took it to dealer and they got me for a $800 New Starter + Diagnosis fee and it worked for 2 days until No Crack No Start again.. Finally get it Started and Limped it back to Dealership.. They had it for 3 weeks and Couldn't recreate the problem... They were leanings towards Bad BCM... They did clean the major Grounds... I got it back from them and it worked for 5 days than Back to same symptoms... Will a Bad TCM also cause these crazy symptoms.
I have a 96 Honda odyssey that only has reverse. only code was the main shaft speed sensor. I changed that out and now it has zero codes. but it still wont move forward at all. but reverse works after a couple seconds. I don't know what to do next. wires look fine. I changed the fluid but old fluid seemed fine. not burned or discolored, no metal.
Hi you sound very knowledgeable let me ask you a question if you don't mind can you tell me if a 2003 Toyota Sequoia has a TCM and where it's located thank you
what about when you put it in Drive it trips the TCM Relay or blows the fuse for the heater and turn signals (one in the same circuit ) I have been trying to track this down for months
Had same problem only involved a fuel pump. I would disconnect heater and see if problem goes away. Then signal lights one at a time. To narrow problem down to which circuit problem is in. Then use a meter to check for bad wiring. Most likely heater. Lights don't normally draw enough power to blow a fuse.
Even though P0700 code is triggered, Ford dealership claimed that the TCM warranty doesn't cover P287B. In other words, no correlation. Agree or disagree?
My tcm took a shit on me three weeks ago and ford has 40 on back order luckily when it went out it happened at Kia where I worked so it’s just sitting there still waiting smh
can you please pay attention to your Audie /microphone // as the volume is generally a little low and in this viedo it went loud at one or two instances ,thanks
08 ford fusion 4 cyl (257k) never had trans issues minus leaks and previous owner changed all shift solenoids prior to purchase.services always kept up on fluid looks brand new out the bottle When sitting in a parking lot or at idle at operating temperature for about 12-15 minutes go for a drive car will shift extremely hard into every single gear violently making the car shake like the trans was on its way out shut the car off and start it right back up shifts perfectly fine and as it’s suppose too smooths shifts no jerks slips etc Assuming the tcm is on its way out since under normal conditions it’s completely fine until you sit at idle for a bit
@@isaiahpina-nt7qtthere's a very good, reputable website called all computer resources that sells them reman, they are plug and play. So simple and reasonably priced.
@thecrusader3941 then i should NOT see this video when i type into the search bar " Location of the TCM on a 2002 GMC Envoy". I had to check with a GM mechanic to not only find the location. But also be informed that the TCM is the same as the PCM on that make and model vehicle. There is apparently three components in one on that SUV. Things were better when there wasn't all this electronic junk on vehicles. I just saw a video on a brand new Dodge truck. And it had problems that only let you drive it about 30 miles. And then it lit up like a Christmas tree. And when the codes were read on it. There were dozens of them. Only to find out that it was one component that was causing all the codes for different things there was nothing wrong with. IMO if its been built since the mid 1980's forward its junk. I wouldn't buy a new vehicle if i had Bill Gates money.
Авто/Мото
I believe that before we even go so deep into the control modules, the very basic troubleshooting checks should be the electrical connectors (bad and oxidized electrical contacts), which can cause delayed or failed shift solenoid operation. Always follow the repair flowchart from the most economical then work your way down to the more costly ones. Without Prejudice to anyone, this is my way of troubleshooting any repairs. Thanks for reading.
@jimmychin8934 how can I access flow charts or TSBs? Website?
My ford focus transmission has been giving me problems lately. Won’t shift into gears , stays in certain gears , doesn’t accelerate correctly, won’t go in reverse. When i took it to the shop they said it was probably the transmission range sensor so i replaced that, had same issues. Replaced the B actuator next it worked for a couple hundred miles then same issue. Replaced the other actuator and it only worked 100 miles or so then same issue. Should i replace the TCM next? I did all the cheaper fixes first but still having issues and don’t know what to do.
where can I find that flowchart for 4L60E ?
My Mercedes e 300 2013 trasmisson malfunction came on and lose power when starting up on hibrid would anyone know what wrong
ruclips.net/user/results?search_query=+Mercedes+e+300+2013+trasmisson+malfunction
One of the best youtube channels I've subscribed to
Thank you I’ve been having transmission problems with my 2007 Nissan Maxima SE not shifting and not running good but definitely there’s a problem with the TCM on my dash I noticed that when I shift the gears into Park or Neutral not showing on my dash but the Reverse and Drive are showing unbelievable how something like this will not let your vehicle run good and transmission performance horrible.
Thank you for your mechanical wisdom. Much appreciated
Thanks for your knowledge and expertise
Hello and thank for this video! I am having problems with reversing and when driving forward it bucks. 2015 Ford Focus.
I've been trying to figure out why my jeep isn't shifting out of first gear. This video was very useful, appreciate you for this one.
Very good information. Unpretentious and to the point. Thank you! Subbed.
I have 2013 charger that had a front wiring harness replacement. It shifted fine going over to the garage, harness was replaced wouldn't shift right after that. Codes up the ying yang clear the codes and sometimes it shift's sometimes no it wont shift right.
The garage says its a speed sensor 1900 dollars to fix , i think someone is full of it. Like i said shifted fine before a harness replacement, something doesn't smell right , i could be wrong but though
Hi love the video my 2009 Acura tl sh/awd self diagnosis within the car show TCM error
The trans when it’s warm up down shifts and goes back into the gear it was in before the down shift. It’s very annoying and no one can figure it out
You’re always very helpful man
Awesome advice! Thank you
My truck is a 2009 Peterbilt 335, in the mornings I turn it on and it drives great, I can drive it all day without any problem, but without turning it off, if I turn it off that's when the problem starts and it no longer wants to drive anywhere, he changed the switch, internal transmission ignition switch, speed sensors and the internal wiring of the transmission and the issue does not disappear, do you think it is the TCM?
Thanks for the video. Hopefully reprogramming isn't hard, I'll look that part up first/now.
thank you very much for this good information. please where is TCM location in Honda accord 2004?
Another great video! Thanks
I have a 2002 bmw x5 3.30I and it’s warning light is saying Trans Fail Safe program what are your thoughts do you think it would be related to the TCM
2008 saturn vue xe sport utility 4-door 3.5l low voltage ANY SUGGESTION WHERE TO START LOOKING
I replaced mine TCM it drove for a while but now it won’t shift . And losses power .
Tips on reprogramming ? I have 1990 dodge van b350
Pretty good smart explanation vid
Hi i need your advise about my scion xb 2005 i changed engine but my transmission wont move my car i put it on reverse and drive but wont move turns on good ?
I have a 2015 Nissan quest and it was crushed on the side of the drivers side. It had a problem when I got it back after repaired that as you were driving it will pull to the left and when you would let it go it would pull to the right or vice versa already exhausted most of my savings in this problem by changing parts that were not it took it out of the shop and changed all of the motor from the motor thinking that that would be a problem and pinion we changed it and we changed the control arms as well Also the part for the little boots which I cannot remember the name of it that got replaced as well because it was worn out. Here’s the that it’s still doing the same thing?
Will the tcm also make truck lunge when placed in gear from a fresh start up? Im having same symptoms with my 2917 t680 ten speed automatic
I have a 2013 gmc Yukon xl slt recently my transmission sounds awful in Reverse and in Drive, sounds fine in Park and neutral. When sitting at a red light I have to switch into D or N but when placing back in D in gives me a big buck then goes. Would this possibly be the TCM? Or bigger problem? Thank you for any help in this matter. We use this for my daughter with special needs. Need to fix quickly.
I want to know what could cause ine day to be fine at shifting and the next
day I only have 1st. gear no shifting to
2nd. third or forth . 4L60 4x4 trans from a 96 sonoma highrider . ?
im going to buy a ecm from ebay can i go to the dealer and get the part number on my current ecm or do i have to pull it out the dash and get it from there i just don't want to do the job twice
I have a 2014 Chevrolet Malibu ltz that shows its symptoms and I want to know if you know of any page where I can buy said module
Good information thanks
I have a 2017 mitsubishi lancer with a P2719 code. I've read about people replacing valves, valve body, fluid filters etc.. then having the same issue until thier TCM or ECU software was updated from Mitsubishi. Any insight into this?
I found1 video on RUclips but it was in a different language unfortunately, so it didn't help me much.
Hi pls suggest what to do i have this error message p0606 component y3/8n4 fully integrated transmission control unit is faulty.. can i service or have to replace the sparepart
How do you change it though I can’t find the video that demonstrates this I have a 2006 jeep grand Cherokee Laredo 🤦🏾♂️
Any advice for GMC transmissions?
Hey, i have jaguar xj 2006 and i have p1605 and p0308, you think my TCM can to be bad?
Could this cause my 2012 super duty to randomly shift in and out of overhaul?
Hey do Chr ysler have a bad control module on it model 2007 v6 300 Chrysler tour
There is a problem with the Rx350 2007 transmission. When the engine is cold, it cannot move forward, but reverse runs smoothly, and after the engine heats up, it can move forward without any major problems. What is the problem?
Do you know about P0700 transmission fault on a Porsche pdk what can be ?
Love the videos!!❤
I am getting a P0717 Code for my trans, which occurred after I power washed the engine bay. The trans is sticking in first gear, clunking at a stop or when I let my foot off the brake after coming to a stop. I am receiving a "Service Transmission" indication on the dash, and a "Service Stabilitrak and Traction Control," too. The TCM is located on top of the trans and connected to the gear shift selector. Everyone says my trans is done (at 200K miles), but I don't believe it because serviced the trans when required so, I don't think its the trans but the TCM. I have a 2014 Chevrolet Cruze Turbo Diesel with at AF40-6 6-spd AT trans. HELP! I don't want to replace the transmission, especially at $6K.. NO WAY!
Thank you my truck battery died and the check engine light came on. Had it check and the code popped up saying it was the transmission control module
I have a 1992 Rolls Royce which gets into limp mode once in a while. Where is located in the car? How do I program it?
I have a 03 yukon 5.3 and its tbrowing no codes but it wont shift. Put in drive an never shifts it pulls of strong in drive and reverse abd wi take off in all gears if you do it manualy. Just put the transmission in. The old transmission wouldn't go to 3rd or 4th now this one won't shift at all
Not getting limp mode but i recieve transmission limitied function hooked up to an obd and this was the only thing that appeared could this cause the issue
Can it make the car backfire during a shift and sputter and lose power and in overdrive make the lockup not work right ?
Will a bad over due transmission mount cause the same problem as tcm
Good stuff my man!!
I'm thinking about buying a used TCM from ebay. How would I go about reprogramming it?
Its for my son's car so I'm not wanting to spend the $200.00 on a new one if I don't have to.
Please and Thank You!
Hey guys, I’ve had a similar issue with my van (2001) 3.3litr v6 I noticed that when I was driving, the van was stuttering and it seemed like it didn’t want to drive nor break and I was only going about 35-45km.
I pulled to the side stoped and turned it off for about 5 mins then I started it drove normal for the first few seconds then it was stuttering again and wouldn’t go past 20-25km so then I turned it off and parked it, after leaving it turned off for awhile I started it and it cranked but then turned completely off in about 20 seconds , then the engine was stuttering and it seemed like it wanted to go but kept on stuttering the muffler was giving out some weird sounds…maybe bad fuel pump?
Transmission gone bad ?
….if anyone can point me in the right direction on what to do….I would grateful appreciate it
I have a 2005 Chevy classic I just put in a new key switch and new ignition switch and my key won’t come out but if I take off
My truck was doing fine up until I used a hypertech tuner on it. Now it's acting like the torque converter is going out. I've already turned it back to the stock program.
2013 Chevy 2500 HD 6.O Gas motor 4x4
I HAVE A 2014 6L90 THAT I JUST REBUILD AND NOW IT DRIVES AND CHANGES GEARS GOOD BUT AFTER A WHILE OF DRIVING WHEN I STOP IT WILL STOP PULLING IN FORWARD AND REVERSE WHEN I TURN THE VAN OFF AND BACK ON IT DRIVES CORRECTLY UNTIL I STOP
PLEASE HELP
Why does my transmission or breaks don’t know lock on drive at about 25mph Honda ridgline2008 drives in gear 1 but not drive or gear 2 car just slams on breaks and stop works again with a on and off. Reverse not working neutral pulls forward
Excellent information...thanks
Thanks fix my 5.3 gxp running like new.👍💯👍💯👍
Hey I have a gxp too and got a p0070 code. Did you have the same? It’s been going into limp mode lately. Going to take it into the shop this week. Also, how many km you have on yours? Mines a 2008 G6 GXP
Same issues I changed the ecm but it’s running really rough at park it idles low seems to be at 600 then in drive jumps up crazy high & seems as if it’s going to stall out I have a 06 gxp Grand Prix
On my 2011chevy silverado lt 4.8 ,transmission work, for about 20 minutes and then it will not go forward or reverse, but if I turn off the key n restart it it will run again, tell I stop at a like, can someone tell me what to look at ,no cord
Will that keep my vehicle from starting?
I have a 2015 mazda 6 were is the tcm located can u make a video
what obd scanner do you recommend?
Awesome 👍
I have a 2000 Chrysler town and country. Wouldn’t start on me. Once we got it towed to the house it turned on but if I wanted to shift gears there’s no telling which one I’m choosing There’s also an obvious vibration under the hood. What could be the problem? No check engine light too
Injector stuck open hydrolocking a cylinder now you have a bent rod.
Would this drain the battery also transmission lacks
I have a 2012 Elantra, transmission issues, changed the pump, some clutches and valve body! Now it drives but great the first time it goes through the gears but starts to shift hard and gets progressively worse until it’s reset, but does it again the very next drive. Please help
QUESTION: WHERE IS THE TCM LOCATION ON CHRYSLER 300 TOURING 3.5 2010. PLEASE REPOND
I can’t get anyone to help me with my TCM because the check engine light isn’t on. It says service transmission after clicking three times.
What happened when the car is in park but on the dashboard it say to put in park and the car won’t start?
Great information, however a link or follow up video on how to reset the TCM or match up the serial numbers would be helpful.
The serial numbers are on your TCM. It’s not hard to locate or snap a pic of. I’m going through the process of fixing mine now that I’ve replaced both actuators and the range sensor but have same transmission problems. It’s a pain in the ass. Screw ford they sell shit cars
@@addisonsigley8033The focus was so shit that they don’t even make cars anymore 😂(besides the mustang) Their suvs and trucks are good though. My shitbox 2014 focus made me want to drive off a cliff. I have a 2017 Expedition EL now and its a beast and super reliable.. The focus really killed their car reputation.
very good idea repost this a. bunch !
You can just disconnect baterry for a few minutes that would allow the TCM to reset
@@addisonsigley8033did it help?
Hey thanks how do you reprogram the TCM
What is p0766 in Toyota sienna 2005
Where is the Tim located in a 09 Buick Lexwrne
I have an automatic 2010 mazda 3 which started jerking when shifting through the gears. i changed the ATF and it still continued and later on the car lost power while i was driving and it wouldnt engage any gear. The mechanic says i need to change my gear box and tcm. While all this was happening i never had any warning lights come on. Any thoughts or comments ?
I am having the same issues with my 2015 mazda. Did you get yours checked?
Any update ? I have the same issue too
What did you guys find out
Fellow mazda owner here that once had same symptoms. Installed new TCM and it fixed the problem!
Great tutorial...My 2010 Impala 3.5L has been having intermittent No Crank No Start issues the Usually begin with a Goofy Start (Starts after Returning from Crank Position to On Position) and soon after, warning Chimes, Service Everything Messages, Gauges go Crazy back and forth, Door Locks on/Off Constantly, Shifts get Rough BUt not Limp Mode and sometimes it actually goes into limp mode.. Once I shut it off for a while a No Crank No Start will happen... Most of the times I can Disconnect Battery and then it gets back to normal.. Took it to dealer and they got me for a $800 New Starter + Diagnosis fee and it worked for 2 days until No Crack No Start again.. Finally get it Started and Limped it back to Dealership.. They had it for 3 weeks and Couldn't recreate the problem... They were leanings towards Bad BCM... They did clean the major Grounds... I got it back from them and it worked for 5 days than Back to same symptoms... Will a Bad TCM also cause these crazy symptoms.
❤❤ thanks 😊
My 2015 Cla 250 is stuck in park I need help
What code is C0700 for in dodge challenger RT
Can a DIY reprogram the TCM?
Does manual transmission has TCM?
I cleared my code for it and it hasn’t came back , you think I’m fine?
I have a 96 Honda odyssey that only has reverse. only code was the main shaft speed sensor. I changed that out and now it has zero codes. but it still wont move forward at all. but reverse works after a couple seconds. I don't know what to do next. wires look fine. I changed the fluid but old fluid seemed fine. not burned or discolored, no metal.
Nice
Hi you sound very knowledgeable let me ask you a question if you don't mind can you tell me if a 2003 Toyota Sequoia has a TCM and where it's located thank you
It's udder the bonnet
What if you get a trans fault but no codes
How to contact with your team? I am looking for TCM for my izuzu trooper bighorn v6 ubs25
What if I disconnected the TCM?
what about when you put it in Drive it trips the TCM Relay or blows the fuse for the heater and turn signals (one in the same circuit ) I have been trying to track this down for months
Had same problem only involved a fuel pump. I would disconnect heater and see if problem goes away. Then signal lights one at a time. To narrow problem down to which circuit problem is in. Then use a meter to check for bad wiring. Most likely heater. Lights don't normally draw enough power to blow a fuse.
I had my tcm changed about 5 months ago and it is failing again
Even though P0700 code is triggered, Ford dealership claimed that the TCM warranty doesn't cover P287B. In other words, no correlation. Agree or disagree?
your reverse sychronizer is worn out..
I have a 97 Buick LeSabre that is reading 40 codes . What should I do with this car ?
What is it doing?
What's the average cost for this repair?
500$
Hey how do I reprogram the TCM?
My tcm took a shit on me three weeks ago and ford has 40 on back order luckily when it went out it happened at Kia where I worked so it’s just sitting there still waiting smh
I got code U0101 : Lost Communication with TCM. Do I need to replace the module? I'm working on a 2012 Ford F550
Hi i get the same code...
can you please pay attention to your Audie /microphone // as the volume is generally a little low and in this viedo it went loud at one or two instances ,thanks
I have 2001 chev express van trans fluid shows overfilled when not running empty when hot any ideas or hints
No shifting problems
That’s normal. It’s going to read high when off. And it doesn’t show when running because you’re simply too low
I have a 2004 silverado that won't go when I step on the gas 10:37
08 ford fusion 4 cyl (257k) never had trans issues minus leaks and previous owner changed all shift solenoids prior to purchase.services always kept up on fluid looks brand new out the bottle
When sitting in a parking lot or at idle at operating temperature for about 12-15 minutes go for a drive car will shift extremely hard into every single gear violently making the car shake like the trans was on its way out
shut the car off and start it right back up shifts perfectly fine and as it’s suppose too smooths shifts no jerks slips etc
Assuming the tcm is on its way out since under normal conditions it’s completely fine until you sit at idle for a bit
Yea you tcu is going out
Mymb w210e 320 cdi wount shift
Great description of the TCM thanks! How do I go about getting a replacement reprogrammed?
Please let me know when you find out
@@isaiahpina-nt7qtthere's a very good, reputable website called all computer resources that sells them reman, they are plug and play. So simple and reasonably priced.
@@isaiahpina-nt7qt see above. All computer resources website
If new, take it to the dealer. If used, no need for reprogramming.
Would a bad tcm module cause a vehicle to not start when temperature is cold outside.
No
Where is the trans control module located on a 2000 TJ Magna ?
Why do you not show where the TCM is located?????
@thecrusader3941 then i should NOT see this video when i type into the search bar " Location of the TCM on a 2002 GMC Envoy". I had to check with a GM mechanic to not only find the location. But also be informed that the TCM is the same as the PCM on that make and model vehicle. There is apparently three components in one on that SUV. Things were better when there wasn't all this electronic junk on vehicles. I just saw a video on a brand new Dodge truck. And it had problems that only let you drive it about 30 miles. And then it lit up like a Christmas tree. And when the codes were read on it. There were dozens of them. Only to find out that it was one component that was causing all the codes for different things there was nothing wrong with. IMO if its been built since the mid 1980's forward its junk. I wouldn't buy a new vehicle if i had Bill Gates money.