Tnx man , these are great videos for amateur diy'ers like me , the endresult on the followup video to this is exactly what im after .... best wishes from Norway
THANK YOU VERY MUCH FOR THE LESSON! i was searching hours on youtube for a tutorial like yours.But mister i really respect you health came first,please use a mask when working with fiber/polyester.Great video again!
Hi CFS, Like your videos on you tube, very useful and detailed, thank you for your contribution. While watching this video I was wondering what is the green base material of, where the model is attached on?
Could I ask how you would recommend making a tunnel for my steering arm to pass through? I had to cut a hole in the fibreglass to allow the steering arm to enter but although not that important as it only goes into a well, I was wanting to make a fibreglass tunnel for it but there is lots of bends and shapes that would be required for the surface part before it enters into the tunnel.
I can never get the mix right I only do small mixes and don’t even get 5 mins till it’s going off Say if I do 20 mils do I do 2 drops of catalyst. Coz I’m doing 0.5 in the syringe and don’t have any time to work with it I did 50 mils before with 1 on the catalyst and then it was not going off was sticky still so I went over it with epoxy resin
Sorry to inform you that did not mentioned what grade fiberglass mate use [first/light weight thjn mat] prior to second lair of 450 csm mat and ratio of MEKP using with. That is very important in a professional manner?
If your viewing this don't take what he says as gospel and watch other vids this is ok for basic techniques and fibreglassing but not anything else find better vids or research more plenty out there 👍
Best fiberglass tutorial I've seen yet on RUclips, this guy is a good teacher
Needing to make panels and such at work. This video has helped a TON for me to create the molds. Plenty of good information within the video! TY!
Tnx man , these are great videos for amateur diy'ers like me , the endresult on the followup video to this is exactly what im after .... best wishes from Norway
THANK YOU VERY MUCH FOR THE LESSON! i was searching hours on youtube for a tutorial like yours.But mister i really respect you health came first,please use a mask when working with fiber/polyester.Great video again!
The ultimate teaching video
Thanx for making Small fiberglass mound in detail.but how to clean after using brush plz ?
So well explained Well done
Great video, can ova be used as a barrier between the plug and the gel coat? Thank you
How long before you coat the resin on top of the gelcoat ?
try mavcoat release if ya want the best. Part will fall out, Boeing buys it by the 55 gallon barrels.
very thanks, this tutorial is very clear. i hope others can see this video.
Good video love the details
Nice work sir
Hi CFS,
Like your videos on you tube, very useful and detailed, thank you for your contribution.
While watching this video I was wondering what is the green base material of, where the model is attached on?
Hi Paul ,If you use the mirror glaze release wax do you also have to use the spray on PVA release agent befor you gelcoat
No, but using pva gives an extra layer of protection. But, the mould will need wet sanding and buffing, because pva doesn't go on perfectly smooth
Lemineshan mat is the Epoxy resin
Looks like that is all done with polyester(?) Can the same scenario be done with epoxy? Thank you.
Could I ask how you would recommend making a tunnel for my steering arm to pass through? I had to cut a hole in the fibreglass to allow the steering arm to enter but although not that important as it only goes into a well, I was wanting to make a fibreglass tunnel for it but there is lots of bends and shapes that would be required for the surface part before it enters into the tunnel.
How many minutes should the gel coat dry to apply the fibres?
Did you let the first gelcoat kick off before applying the second?
Wow really amazing idea can shared
Brilliant tutorial, learnt a lot from that 👍🏻
Wow beautiful work 👍
I can never get the mix right I only do small mixes and don’t even get 5 mins till it’s going off Say if I do 20 mils do I do 2 drops of catalyst. Coz I’m doing 0.5 in the syringe and don’t have any time to work with it I did 50 mils before with 1 on the catalyst and then it was not going off was sticky still so I went over it with epoxy resin
Best job sir,
Amazing
which jel coat useing
Would this work with my Europe dinghy
Is this guy using polyester resin without a respirator?
What matarial used can you talk me please please please
Great video but can I ask how long between each layer of glass did you leave it?
Well done......What is the name of the 1st mat you applied to the mold ??
Surface tissue
@@garyengland5326 do you have to let the surface tissue layer dry before you add chop strand or can you work straight through ? Many thanks in advance
Good👍
Fiberglass ASMR.
How would you mold a hull that has a tumblehome in it? Is it possible to do it this way?
If it's a coble shape, you need to make a two piece mold. It's the only way.
polyester resin?
Sorry to inform you that did not mentioned what grade fiberglass mate use [first/light weight thjn mat] prior to second lair of 450 csm mat and ratio of MEKP using with. That is very important in a professional manner?
hello, what if I did not put gelcote, will it work??
i would like to know where can buy unmolding oil for resine
Or what is the exactly name of unmolding oil?
Looks exactly how i pulled mine out seeing as this is my boat plug😂
wow 👍
I am looking fiberglass job any vacancy in your company
👌👌❤️
Hello
Powder- or emulsion- bound Mat...???
Emulsion, powder is for epoxy, emulsion is for polyester
best .thanks
Leminesh polyester resin Epoxy resin
If your viewing this don't take what he says as gospel and watch other vids this is ok for basic techniques and fibreglassing but not anything else find better vids or research more plenty out there 👍
??