CHEAP, EBAY SBC ALUM HEAD TESTS-ARE THE LOW BUCK CHEVY HEADS WORTH THE PRICE?
HTML-код
- Опубликовано: 3 июл 2020
- BACK TO BACK SBC TEST-FULL RESULTS. DO CHEAP SBC ALUM HEADS ACTUALLY PERFORM?
What happens when you compare no-name, cheap heads to brand-name, performance heads? Do the cheap heads actually make hp? if so, How much power do the cheap heads makes? Are the hp gains worth the price? How do the low buck heads compare to the brand name heads? What about the big-$, brand -name heads-are they worth the price? We ran them back-to-back to find out how they stack up! Check out the full results. 
Авто/Мото
Exactly the testing that I had wanted to see, Richard!! This is helpful for stuff we have and future projects!! Thanks much!! And dont forget us SBC guys, we're still out here!!
I'd love to see a comparison of the procomp/speed master heads vs vortec heads
On a 383, you honestly need a 210cc or slightly larger port to make good power. Stock vortec heads are 170cc and would choke that motor down power wise, but make a shit ton of low rpm torque.
me too!!! or pro comp vs gt40 pro comp vs double hump!
It would be a better comparison. They are fairly equal. The pro comp heads do have the taller runners and I would recommend a vortec intake, because a factory gm high rise intake sets just below the top of the runner.
@@biggregsparks8364 not true, if it's the typical 6000 max rpm stroker kit the added flow isn't as helpful as you might imagine. For an na deal the higher velocity of the 195 street ports, and the stronger low lift flow will help drivability for the typical street car guy. Most guys aren't building a race car. And the added flow above 550 lift is pointless if you aren't spinning the rpm to take advantage of it... Again, I'm referring to na stuff. If using a power adder then sure. Also referencing afr cnc ported heads with stated flow bench data and known csa. Can't comment on the as cast import stuff. Although it's interesting how the afr 195s have been tested against some 200/210 speedmaster heads and basically kicked the shit out of them from idle to redline.
@@biggregsparks8364 the other thing this test isn't showing is you have even more flow with the afr and a properly spec cam. The afr will flow with around .550-.575 lift. So in truth a custom cam would show even more average power out of the afr.
Man, you do really good work. I appreciate that you do real comparisons that guys like me are interested in. Thanks for making good content!
I put I set of AFR 195 Eliminators on my 355 because I wanted the best head I could get out of the box and they didn’t disappoint!
I put 190cc AFR heads on my '85 Corvette back in 1993, replacing the stock cast iron L98 heads. I did the whole cam/heads/intake/headers thing all at once, as a winter project. I have run the the Corvette in road course use over about 16 seasons, and the AFR heads have never given a problem.
@Hello Kitteh Retrofit hydraulic roller. 224/230 effective duration. Comp Cams
@@andyharman3022 hell yeah man that sounds similiar to my build. AFR 195s and the XM276hr cam. same 224/230 split 112LSA
As a previous owner of Pro Comp 180 (as cast) heads, it's my opinion they are great for a tight budget if you are seeking to upgrade to Aluminum heads. I found myself needing to replace a set of worked over 461's that had developed a crack & had very little to spend at the time. The throttle response was definitely lacking after the swap. Therefore when I recently replaced that engine I went with a set of AFR 180 CNC heads PN 916. I would only use those Pro Comps again if it was a stock to very mild daily driver.
Richard, I was watching this while eating dinner, and everyone outside is shooting off fireworks. My little Jack Russell was cowering on the floor beside me. But when I started your video, she looked up and started wagging her tail. She must have thought you were talking to her, and your soothing voice erased her fear. Thanks man
Great info. All your videos provide good information, but for me this was one of your better ones. Shows what you get for tour money. Thank you
When I found a barely used set of AFR 195`s for $1000. I jumped on them and didn't bother to haggle.
I know someone always says it, but these videos are gold. thankyou!
I've been waiting for this!
Thank you Richard for sharing your work. You truly are a Engine Master
Never skimp on your cylinder heads,if your trying to build a performance engine ya want the best heads you can afford. AFR is expensive heads but you can’t beat the out the box power capability that their heads make. I have a set of the 220 comp heads on my 427 small block Chevy and even though they costed me close to $2500 they was worth every penny. 650 horsepower in a 2800 pound Chevy II makes for lots of fun so trust me spend the money ya won’t regret it and after all it’s only money your not going to take it with ya and it’s meant to be spent anyhow.
I have an NHRA SS/J Chevy II I use NHRA legal Edelbrock heads on. Its a 327 that makes 780 hp @ 8500 RPM. It too is a 2800 lb car with a full interior, 6 point roll bar, and no modifications to the body or the hood. My question to you is why in the hell would you build a 427 cubic inch small block when a 427 big block will blow it away so bad its not funny? Youre making 650 horsepower? Yea right and Im the Pope. Spin it to 7 grand for any length of time and youll have pistons and rods scattered all over the track. You guys with your mixed matched pieces and parts crack me up. So what is its E.T. and MPH on a quarter mile track anyway?
@@MasterWitchDoctor there’s nothing mismatched and the question isn’t why its more of why not?? It’s a new millennia,technology has come a long way. It has a dart lil M block and there’s no doubt the motor would make way more power but it’s a street car and was built for 300 shot but you clearly know it all. I know it’s not very practical no but it’s a toy. As for turn it any real rpm,well I shift it at 7300rpm and rods are still in it and I would have to go dig the time slips out the glove box for exacts but it runs 9.80’s all day on motor. I never get more then one pass as I get kicked out every time as I have no cage. It’s a ladder bar car that’s all that has been done so I could put a 26x10 slick without cutting the car up. It does have frame ties an a simple bolt in coil overs up front. Still have the factory cammed lower control arms up front and upper A arms and strut rods,Still has the rear steer that the first gens came stock with. That’s exactly why I didn’t go big block when clearly the cylinder heads well out flow most factory style engines,but have ya ever tried shoe horning a big block into a first gen x-body? Especially with it still having a factory front clip. It’s 64 factory SS car so I wasn’t cutting it up especially when it was my fathers car. The engine is capable of a lot more when it was on the dyno,it had a 750 street dominator on it. It now has 1100 pro systems .699intake .702exhaust can’t recall the exact duration and Doug 1 3/4 inch primary with 3 inch collectors. They make 2 inch fender well exit but again didn’t wanna cut the car up. If ya ever in the south east Michigan area and wanna put ya money where your mouths at?? I know quiet little section of road that we can go and see if your shit can hang. I won’t even spray it and will let you the nitrous line off and tape it your self so ya can see it’ll be all motor.
AFR FTW! I have seen countless AFR dyno tests, and they never cease to amaze me every single time. They always make killer torque throughout the rpm range, from off idle until they let off the throttle! YES, they are and have always been very expensive...BUT if you are building yourself that once in a lifetime perfect engine that you want the most out of for maximum fun....AFR will always outrun the competition and it won't even be close! Don't put all kinds of money into a car and then skimp on the cylinder heads because THAT is where your power is at!
Won't matter if ya jammed some boost down it's throat gonna make power regardless. Cheap heads will make killer power with 144 or turbo.
Your videos are enlightening thank you and your crew for all you do!
This is knowledge and knowledge is power. Thank you Richard!
Customer: I want to go fast.
Shop: How much money do you have......Money = Speed.🤔
However, as hi end technology continues to trickle down to the unwashed masses (a CD player was 300 bucks 30 years ago, now you can get one for 30), you can go much faster for a low price than you could in the 90s. Competition between brands is good for consumers.
So much cheaper to buy a ZX-14 or a Hayabusa than build a motor, transmission and drivetrain for a car if you want to go fast.
@@2010HarleyDynaFXD, Totally not the same
@@joejones9944 not the same but you go a hell of a lot faster per dollar
Did I hear him right? Did he say ass hat heads?
As others have said its really not apples to apples when the afr's are cnc ported (which we know alone increases flow & therefore hp) and although port volume was close it would've been nicer to see a direct comparison with the same port volume, chamber volume(advertised of course) , and valve size. I think that would really be a fair test to see if the expensive heads are worth it.
Thanks a lot for the content! This is something I've been wondering about for a long time.
It’s not just about price it’s also has to do with where the heads are made. Like the budget made in China intake. We need to stop financing the enemy and stop shooting ourselves in the foot by also offshoring our industries. It matters!!!
I agree 1000% but in a tight economy seeing a performance oriented aluminum head on the cheap is to tempting to alot of gear heads but you get what you pay for shit even factory votecs with flow better than those mediocre pro comps alot don't realize it would be cheaper to snatch up some good used vortecs and grab the diy tools to mod em for more lift and rocker studs for under $100, get a die grinder and cheap sand roll set, carbide bit and a porting book and do some basic work and get seat of the pants improvement ya know
I hate turning in an old car battery to the scrap yard. I get a few bucks, but I think all the lead in it goes to China. Not Good.
I’m running a set of procomps on my 0.060 over 351-w. I just had to try a set out of curiosity and my opinion for people who don’t have the machine shop experience, go name brand cylinder heads and buy them bare and have a good reputable machine shop build them. I had to put about 25hrs into my set of procomps With cleaning up the castings, reshaping the combustion chambers, I redid the valve job because the margins where crap. I had to use two piece guide plates for proper valve train alignment. I went a best of 10.40’s on a 100 shot with a mechanical flat tappet camshaft. .500 intake-.522 exh. 225-235@ 0.050 on a 112 loc. TRW flat top forged pistons.
@@StainlessTIG2 yeah there's plenty of benefits to running even Chinese heads I just can't afford $2000 for set of big name ones and I'm not shure but I'd say the cheap line of big name ones may use Chinese castings? Maby not. I just have a set of 993 GM castings that came with bowl port, 2.02 .60 S/S under cut valves and studs from arrowhead bout 20 years ago I did the rest of the porting and polishing and I can say they work pretty good as much as people trash em, yhey actually flow pretty good there downside is the chambers are not that good but with flat tops I have 9:1 that's a good street compression for iron heads. With a Howards 232 480 108 lsa cam original Torker and roller rockers it is pretty damn healthy, no its not 400+ HP but I'd say 350+ even tho the forum experts have said be lucky break 300... common...wtf. but in a 92 c1500 it does cook along
@@95Sn95 the 993s actually outflow the double humps! The problem being the 76cc chambers compared to 64cc. It made quite a difference in our dirt track pure stock motor, years ago, to run the smaller valves good casting 305 heads, because of the increased combustion. We weren't allowed Vortec heads, and only flat top pistons and a max lift of .450! Very restrictive rules.
I bought the AFR 210 heads when they first came out 20 years ago they were $1375 a pair assembled
I would like to see the AFR195 as cast heads in a comparison. They seem to be a lot cheaper than the CNC heads, but they might be a lot less power as well.
Cause there Chinese
Love the data you provide! Thank you sir 🥳
Awesome test. Nice work Richard..!
Great video! I appreciate you putting all this together for all of us to see. If you need any new content ideas, I agree with a lot of the other comments. I would love to see the middle ground heads like the brodix ik, blueprint 195s, Edelbrock e street and so on. As always great stuff.
I would like to see that too
I have been running AFR heads for years on a boosted combination beating on them with great results and no problems definitely worth the price , you also have to consider that a low cost offshore head likely will suffer in heat treating and longevity issues with valve seats , heat treating , plus the AFR’s come with high quality valves and springs. Want to go fast and engine last eat lots of Kraft dinner till you have the money for quality components
Always great stuff from you Richard ! Thanks buddy
My pleasure!
It comes down to an old saying “ you get what you paid for “ and for me i would be paying for the AFR heads any day of the week !!
You know exactly what you are buying , no surprises at all ! And all of the measurements are accurate!!
i bought some NEW aftermarket LS3 heads on craigslist for a screaming deal. Even got them CNC ported! Tossed em on the engine and the thing couldn't stay cool. My screaming deal craigslist LS3 heads had a plugged water jacket so there was NO water flow from the water pump. Waste of $2500, plus I gotta buy another known-good set of heads to replace em. I got what I paid for!!
@@rustysausage69 YOU BOUGHT THEM ON CRAIGSLIST,IDIOT
I have the afr 195's on a very similar engine. 383 10:2:1 rpm intake lunati 270hr and it's a great daily driver that will destroy tires at will.
Interesting, thanks.
I'm curious about the Edelbrock offerings. They are marketed as a sort of 'middle-of-the-road' head option.
Would like to see that too. I have Edelbrock Performer RPM 64 CC heads. Going on my 355 with lunati voodoo cam
I'm not sure how I messed this one Richard. Outstanding and useful shootout. Well done!
Thanks Richard ! I have a built gen1 short block. This helps me a lot !
This is getting better and better Richard... Your hitting every angle of the engine world💪🏾💪🏾💪🏾
I would love to see a shoot out with the skip white nkb200/proheader/assault heads against a dart 200 platinum head. These are copies of the dart heads. A CNC program will work on the the above China heads, and they are pretty nice castings.
Excellent video! I'm at this point now I have the same pro comp heads on a 383 I have ran them at the track and they are just not enough! Afr is where its at
I needed this info Thanks Richard
Me too lol
If I have learned anything from engine masters it is buy the best head and intake you can afford.
Hey Richard I enjoyed this. I knew the AFR head was going to produce the goods. It would’ve won out even if you had put it up against the larger CNC Procomp in the same comparison. I think it comes down to what you can afford, but for a $400 difference between the two CNC’s I’d beg for, borrow or steal the $400 bucks.
Cheers & keep up the good work😊
Yea and put the bigger AFR on aka 210cc to 210cc and retest...shit...
Love it! I just did a inspection video on my speed
Master heads
GREAT VIDEO RICHARD!!!! BOTHARE GREAT HEADS. DEPENDING ON YOUR BUDGET.
I'd like to see the same test with higher compression. Step it up to 11:1 and I bet the AFR heads really start showing its true colors but even at 10:1 it was a considerable difference. Great vid 👍
....or you can spend that extra AFR head $ on a 76mm ebay turbo and make double the power with the China heads. I'm on a page called the driveway engineer where 30k a year mechanics make 9 sec drag cars on 8k budgets. Learned a lot about how to go really fast on a budget.
You should do a budget head shoot out ,seems like everyone has a pair of heads in the 1000-1500$ range ,brodix ,trick flow ,pro filer, AFR ,all around the 190-200 cc range ,see were they all stand
Yup, and Edelbrock E Street, Promaxx, Blueprint, and on and on...
RHS was pretty good , but was 8 years ago I ran a set. Bought bare. Damn good head when I couldn't afford RHS
Would have liked to see a 461 cast iron production head in the mix as a base line to .
Thanks Richard. Very diplomatic comparison. I have heard some of the Chinese performance parts such as heads won’t even bolt on some engines. The old saying you get what you pay for has never been more relevant.
Sadly here in this case you get what you pay for.
Thanks for testing, makes it easier to make an informed purchase decision.
You're awesome, keep up the good work.👌🏻😎👍🏻
It depends what you’re looking for. For a daily/street toy, pro comp heads are just fine.
Would love to see this same test but for the cast iron heads, stock vortec heads vs dart iron eagle vs maybe world products, you get my drift
That's what I'm talking about.
Dart and RHS win.
Cast iron vs vortec!!!!
Let's do middle of the road sbc heads, Flotek vs Promaxx vs Profiler vs Brodix IK vs AFR enforcer. All in 195ish to 200cc runner. All as cast. 64 chamber.
Never did a direct comparison but I really liked the ik200s
Now that is a super idea for the regular joe gearhead. I bought Flotek 190, 64cc sbc heads over cast gm fuelies and gm Vortecs to build a 327 L79 clone.
Really hoping my promaxx 190s do good things for me. Mines not a striker but the xe 274 flat tappet comp cam and flat tops with scat rods and a dual plane with 750dp. Here's hoping. If it makes close to 400 I'll be tickled.
Stock Ls heads out do them all
@@horsefly1020 good thing this video isn't about LS heads then huh
I have a set of brodix iron killers on a mild 355 in my s10 build that runs very well they were right at $1000 for the pair ! as always thanks for all you do !
Interesting. Thanks for the content
I’m curious about the Promaxx 190 cc heads. I did some research, and they had quite a few more benefits to the Pro Comp heads. I port matched them, cleaned up the bowl areas, and cleaned up what little machinists ridge there was at the valve seats. Could you do a show on how making these modifications would help?
you added about 5-8 horsepower
I would like to see a head porting competition from well known head porters. On same head and engine combo. And then dyno
That would be awesome!
Not sure how your reading my mind Richard. But I am building a 383sbc forged bottom end with with flat tops, and the XE284 camshaft and some older pro topline steel heads. And I’ve been trying to figure out dual plain or single plain. Now I know. Thanks!
Great video Richard. I waited to have the funds for an Afr head. They are great heads even on a sbf.
Good choice-their SBF heads are on point
I think you could have added Blue Point and Eldebrock heads to get some that where more mid range although they are far from cheap. The added torque and horsepower is impressive.
You mean Blueprint? Autocorrect gotcha!
It's better to show your tail lights to your competitors than seeing theirs. AFR all the way.
Not to mention made in the USA. Quality components throughout
trlprk seen a seat drop from a afr 227 not very pretty .theres someone on you tube that always goes through afr heads.i had edlebrock head missing a spring cup and spring dug into the head I still trust domestic more but they are not perfect.
@@caseym3118 this is a fact! I've been thru many top dollar top brand heads. & everything else that either tolerances, clearances, specs were out to lunch. How about being $3k + heads, & then having to do a valve job. Happens more than most think. They think hell i have AFR, Edelbrock, Blueprint, etc etc etc, so im good, & i can just trust it because it's not china junk, and they can be really wrong. Most of the time, they aren't too bad, or too off, but most of the time still off. And for most , they won't notice these issues, &/ or if they do its later after everything is together & finding were their issues or bugs are originating from is a complete engine tear down. Again typically goes unnoticed on their "mild" builds, or weekend warrior streetburners. Now on those high end builds, most even have their top brand stuff gone over by real machinists, as do i will. I can build them from the ground up, except for the actual machine work, but i also know how to check a machinists work. This is something I highly recommend others learning!
I have a 350 .40 over balanced and blue printed motor with 190cc pro comp heads...Basically the same set up as that 383....750 carb ,1.6 rollers , edelbrock dual plane rpm....
What would be a good AFR head for my set up if I want to switch out the pro comps ? Would the 195cc be a bit much ? Or how about the 180cc AFR ? Not sure if they make that size
@@johnnydoubleu3656 here's the deal, the reality of this, what are you trying to do, where are you trying to primarily make your power in the power band? High flow doesn't mean more power. More top end high RPM horsepower yes, but can mean less low end torque, unless you are building up the lower end to push up the entire powerband.
Also after deciding where you mostly want that power, mostly a street machine torque monster, or all top end race?
Then, what other components do you have or are planning to use? Cam specs, valve train specs, intake, exhaust flow rates, SCR, DCR, etc etc because after the first part i mentioned, all these component specs are detrimental in matching all your components correctly in a way to get desired results.
In truth based on what little specs you gave, chances are you would see very little benefits from spending that much on AFR heads. Again i could be wrong about what you have, but the impression is that you have a mild street machine.
I know many people will throw a bunch of ideas, or what to use, etc. But as i said, 1st decided where you're trying to go with your engine. Too many will recommend what they heard, or whatever hype is trending, & most of time this does not mean the best results to whomever it's being recommended to.
I have a 383 and am in the market for new heads. I also think I'm in the market for a single plane intake.
Love your videos !
Brett from Montana .
Good video as always
Great video , Is anyone ever going to do an Edelbrock Victor jnr head SBC youtube video ? Richard should be the first !!
They are pretty pricey,the only build I ever saw was in an old mag back in the day,it was the vic jr cam& lifter kit, vic jr heads along with the port matched intake,and a 750 cfm edelbrock carb, it was a 355 10.5 comp and it made if I recall around 508hp-515hp ish in the high 6k rpm range.
I've had one too many problems with Pro Comp, aka: Speedmaster... which brings up the whole point, why the name change? That's a hint in my estimation.
Universally known as poor!
Well, My response is pretty neutral because I agree with most of the comments that I read.
First, I want to say that I enjoy your work and videos. Thank you!
Now, when you were talking about what the cheapo CNCd heads did, keep in mind that this is on the older,milder 383. I took the gains over as-cast as a percentage and applied it to the 405 hp of the current cheapo results and it doesn't look as pathetic!
I would agree to go with the AFR heads, if you can afford them.
Now, if you can port your own heads, the cheapo heads could do more. If you are broke and your budget is either used factory or the cheapo heads, they might be a bargain.
Now, consider how much time you are going to invest in porting them. Do you want to invest your time in the cheapo ones?
I believe that you could nearly match the cheapo heads with a set of used Vortec heads. I know that you weren't doing junkyard heads here. I guess the cheapo can be used on a completely bad budget but I would still lean towards a less expensive, brand name head...
I agree with buying American and also think folks need to realize something else. When you buy foreign, you aren't just losing American jobs but you are losing the Manufacturing ability of the shops that you helped put out of business...
Ya'll Take care and be safe, John
Good info Richard!
i wanna see a speedmaster head hand ported and polished go against the afr head
Glad you said that i have a pair of procom 210cc heads these heads can be ported bigtime i did mine and i will tell you my 78 malibu 358 is stupid fast i just bought a set of afr 195 inforcer heads im porting them now cant wait to see the diff im opening them up as much as i can
stupid comparison,you could spend 100+ hours hand porting a set of heads,what does it prove? you can not port to cnc repeatability and efficiency EVER.....EVEN THE BEST HEAD PORTING GUYS CAN NOT DO IT
You should have baselined the test with some factory vortec heads. Everyone says how great they flow, but there are not a lot of tests comparing them. You should do a test with a set of fuelies, 882’s, and vortecs.
Good point, what about durability long term. Are valves going to leak?
Wow what a big difference thanks great information
I was told a long time ago, buy the best head you can afford. I will work more side jobs to afford AFR
They're worth it
Why don't you guy's used a 600 lift roller cam to test both heads.
Even tho I'm not a Chevy guy. I really appreciate this video . And who would of known the gains would of been that substantial!
I had procomp heads on a 302 with tfs1 cam and trackheat intake in a fox mustang, it put down 250hp and 295lb-ft. I swapped the heads out for some 58cc tfs 170 heads and nothing else and the car put down 310hp and 343lb-ft. A 60hp gain at the wheels is huge, I always advise people to spend the money and get the brand name heads.
It's getting to the point that inexpensive aluminum heads like these ProComp/Speedmaster heads are less money than doing a full rebuild on a set of iron GM heads. $800 at the machine shop for stock iron heads, or spend the same for aluminum heads. No brainer really. As for cheap vs steep, I'm a big proponent of buying the absolute best cylinder head you can afford.
Also the AFR 195 head has 8mm valve stems, bigger 2.05 intake valve, and 5 angle valve seats. That head has more than just the basic CNC stuff. So of course it should out perform a as cast cheap heads. I would love to see the sane AFR 195 comparison with the Trick flow 195 as cast, now that would be a treat. But still Richard always has good content!!!
Forgot bout the larger valve n better VJ in my reply, good points!
Ya shoulda done the AFR as cast head. When r u gonna do a 350 Olds, Pontiac, and Buick comparison? I love watching your show. It's extremely informative. It's like a drug that I can't get enough of. LOL!! Keep up da great work. From Chicago Matt Da Hippy.
Richard Holdener this video talked me into buying the AFR heads, wondering if you'd recommend the same heads if I'm planning on adding boost in the future? Due to compression and what not. I'm already running a 100 shot of nitrous. Thanks!
How can even think that's a fair comparison
The procomp CNC might have made more then 40 hp difference if the cam was more aggressive as in the first test. This is not apples to apples.
It showed the difference between the heads with the same cam. A bigger cam would have also helped the AFR's so the difference would still be same until you reached the limits of each head with a particular cam. A bigger cam would have moved the build out of the street range and into something less streetable. More top end at the expense of the low end.
@@mikes9939 the procomp cnc test was with a much smaller cam vs the first two tested.
It was only 15 hp less. That's not a huge difference.
If the valve on made in China crap has problem sealing the Cnc won’t help much
The are a couple more things to consider when selecting heads, or anything else for that matter, and that is quality and the individual components performance like the valves and springs. I would think reliability and performance are important considerations, how much the valves open and how they perform at higher rpm, consistency between individual valves, durability etc. Those cheaper heads are really expensive if you can only make one run
this is an interesting video, because some engine builders may have blown most of their budget on the short block, and had little left for heads (which they can add on later). But some budget builders would grab a junkyard 350, and either toss on heads for a cheap NA power maker, or a power adder (or the cheap heads with a power adder).
I'm sure there's a video somewhere in this series, where an attempt is made to turn a Vortec 350 into an LS--ie, cheap good flowing heads, and a cheap power adder like a diesel turbo or an eBay kit.
Buy once, cry once.
WISE DECISION.😭👍🏻
Absolutely... though I'm one of those guys that goes through all the cheap shit then ends up buying the good shit in the end, every time I try to save a buck something breaks or it doesn't work, I said the hell with it and borrowed 10k and bought afr heads and a dart block along with all good internals, we'll see how I make out I guess...
@@88_turbo_fox73 borrowing to go fast is kinda stupid
This is why I'm building a junkyard 5.3. I'll make more power with a cam swap for less money than the a set of heads.
Haha, real talk. Those things are amazing. Get a small turbo and you could be pushing 600 easily.
Great info. I have pro comp heads with those same specs for a sbf that I plan to use in the 66 mustang I'm restoring.
The AFR heads rock. I'd make only some slight changes to the combination. I'd run the first xe274H cam with either an RPM air gap.
--That said, I'd get the speedmaster heads if I was gonna do a truck with a 218 cam since it's such a huge gain over a stock head.
Either way, I'd take either head to a machine shop and make sure everything is dead nuts.
A cylinder head that comes to mind is the Brodix STS 227, since it's meant to use shaft mount rockers. I see that as the point where the SBC is at parity with an LS, or maybe even a hair better.
I would like to see the cheap heads run again with a good valve job and a proper set of springs
But by the time you do all that might as well just buy a good head
I have a set of pro comp casting. Put good valves and springs in. Complete for both heads in $700 BRAND NEW. And that's small block mopar. Not one issue here
@@daddysbrokegarage the castings aren't super consistent with the pro comps. There are definitely worse, but they're not the best I've ever seen.
The ProMaxx heads are a surprisingly good casting for the money, have them checked and assembled properly by a machinist and they'll put down good power for the money.
Regardless you have to check every brand of heads I don't care if it's AFR Frankenstein to pro comp... Ask any real builder... And yes pro comp can make Power
I love the low end torque of a SBC! Been debating on putting a cam/head SBC in my truck over a LS.
Ls 6.0 wit a truck norris cam makes a flatter torque curve and more peak torque. Imlo.
ruclips.net/video/-tRvLiJbdzc/видео.html
Go to 3:00
@@safetyfirstintexas thats not a 6.0 in that video
@@joshuadyck4861 where did i say it was?
@@safetyfirstintexas not saying you did, but you talked about a 6.0 with cam and then referenced that video, kinda implies that
@@joshuadyck4861 people are creative like that
My engine builder talked me into RPC heads over Edelbrock on my 357. I hope it was a good decision.
Do a test and include a set of stock vortec heads worked for lift, vortecs ported and the AFR heads
The build quality between the two brands is completely different. You’d have to spend a few hundred on the Procomp head out of the box just to get the valves to seal.
You have got that right. And when that thin head goes through a few heat cycles it is leaking again, I've seen over 20 hp in the valve job. Maybe Richard will do that someday.
I’ve heard the guides wouldn’t last long either.
@@timtodd6830 Procomp is junk!!
They have a bad reputation in Australia. Chinese made rubbish
@@davidreed6070
They copy all the brand names & its all junk. You are better off to spend the extra dollars & get a quality product rather than end up paying more in the long run.
Yeah I wouldn't trust the china heads, I had a valve head fall off of a china valve and punched a hole in the piston on a ford 5.4. It was just a work truck, weren't even beating on it. Didn't save a cent doing that.
I'm curious how as-cast AFR hads would have fared in this test.
Me too. A bit less pricey as cast.
Cast heads will preform just as good as the pricey aluminum heads
@The Truth about Africa hurts we aren't talking about cast aluminum here I'm talking about cast heads such as vortec chevy heads your machine shop can machine them to be some of the best performance heads ever I know I run them on dirt track
@The Truth about Africa hurts them being aluminum really doesn't affect the way they preform not enough to feel it behind the wheel but aluminum you can cut and modify alot easier plus you get a weight reduction and they do run a little cooler and cooler fuel means better mixture and bigger booms
How much more hp and torque did the "cheap" heads make over stock iron heads?
I had some S/R torques on my 383 Chevy. Almost all the valve springs cracked. Replaced all the springs and it was fine. After that,I'm never buying budget heads again. I heard many times that they are basically thrown together with crummy tolerances with cheap parts. I'd rather just save up and get what I really want,put together with quality parts. Eventually about a year later,a valve seat cracked in one of those torquers. I slapped on some used vortec heads. It felt like that 383 gained about 20hp. Just because it's aftermarket doesn't mean it's better.
i have the blue print engine version of the pro comps Part #: H8002K they run about 900 bucks which when you're on a budget is a great deal.
we have run a lot of BPE stuff
Either version of the sbc BPE are not the same as procomp, different ports and chamber
Would that difference been even more apparent with say a solid roller cam with around 250 duration at 050 and 0.625 lift?
It would
I’m using the Nkb 200 with 9.8 to 1 heads ported with gt3582s @.050 254/265 .600/.600 114 LSA solid roller wish me luck.
Id like to see a shootout between aftermarket gen 2 lt1 heads, and a popular porting job on stock heads from lloyd elliot.
I would love to see a comparison of the air flow research head vrs the world products sportmans 2. With 200cc runners/64 cc chambers.. Better match
It might be interesting to to compare the cost of porting the cheap heads to get them to make as much power as the afr heads. I bet it would be more! What I thought was impressive with the AFR heads was how nice the power curve was, and is a sign of a lot of refinements.
not sure you could get there with the Speedmaster 190 heads-maybe a good porter
@@richardholdener1727 If the porter is only allowed to "remove material", I would totally agree- at best all that would happen is the peak power might get close but would not have a nice power curve, because the port volume would have to get bigger, making it "lazy". If the porter is allowed to cut and re-weld, I bet it could be done but it would then be crazy expensive and almost certain to not last long. It is really hard to gain "good" airflow where the port doesnt loose alot of speed and keeps the gas and air well mixed, and have every port consistent.
fun but stupid idea,welding and machining an inferior pile of crap to "try" to make it better isnt worth the massive headache it would create
Hey Richard can you do a test on a 3inch Y pipe vs. a 3inch dual exhaust on a 383, 350, or LS?
I have that set up on a third gen. With long tube headers.
Sounds awesome. Runs damn good too.
Engine Masters already did that test. Check it out on Motortrend on demand
Engine masters did this recently
@@656hookemhorns what of you dont have motor trend on demand?
@@adalmadera25 Subscribe, if you can afford it, good value in my opinion.
I love these kind of tests. Thank you. And do you have any info on the Brodix IK 200 heads?
I have run a few Brodix heads-I'll have to check-they have always worked well
Old comment but a friend of mine just swapped his brodix ik's for a set of AFR's. Lots of variables [406 sbc DART block, roller, high comp, glide] but he is faster than ever with the AFR. And very consistent, he runs a 10.5 or 10.0 index bracket and is very happy. Just one guy's experience.
I bought EBAY Old Nascar Phase 5 Aluminum Bowties, Pulled old 80's .740 lift solid roller used comp bracket cam we had laying around new pistons, rods, old craigslist Strip Dominator w 2" spacer 850 carb 355 CI 11.75:1 compression New comp lifters I will say I went with 3/8 push rods and had a really good full kick out pan on it Dynoed 565HP The head cam combo was killer ( we were racing it whether it was or not) We call it the EBAY motor You can build some fun reliable stuff if you pay attention and do your homework.
Hey Richard you ever do any sb2 head testing?
I have not-pretty small market
Good head if your building a 800hp NA SBC.
@@richardholdener1727 Richard, at 4:25 in the video, what is the pipe plug in the front of the block, just above the timing cover, for ?
I am running that same “first combo” same style pistons same cam same heads and I’m not impressed with how bad it noses over at 5500. I would be curious how much hand porting would help the procomp head
When you say "noses over", is it breaking up from valve float, or just running out of steam?
@@jeffrykopis5468 doesn’t break up or misfire or anything, but it’s like it hits a wall and runs out of steam
@@jeffrykopis5468 I probably need stiffer valve springs either way
Great info!
@richard holdener have you had much experience with the Promaxx heads?