I will say that I do not think the vast majority of people will need to perform a static time, a total centrifugal advance time, an SVDA advance-only time, and a full DVDA time on their engine in order to dial it in. But man, you did an outstanding job on this video so everyone should be able to time their engine wherever it sits currently. Thank you!
Awesome Explanation. This is the only DVDA setup I’ve seen that makes perfect sense. Much appreciated! Just ordered a remanufactured distributor from VWNOS…Many Thanks!!!
This video was one of the best videos I have EVER seen on timing. Thanks a million! I have a DVDA with pertronix ignition and I have been having trouble with tuning because I have been timing my max adv with the hose connected. I think this will solve my problem and I can't thank you enough for the insight!
I agree, that was brilliant, a little closer would be the only thing I could think would make it better. But only because I'm a "Green as Kermit" rookie ...Lol
I have a SVDA 034 with electronic ignition, but I haven't built up the confidence to change it and time it and all that. Kinda unsure whether I need to change coil or not. I have the stock black Bosch from 1969. I believe they have a built in ballast resistance but I'm not sure. Don't regular distributors with points require a ballast resistor? If so I'm good to go. Self-doubt is my worst enemy. Thank you so much for this video.
when you time it at max advance at 30 degrees 3000rpm,, what is that actually ignition timing when you measure it at idle. so at idle point the gun at the block casing marker and get the tdc mark to line up, whats the gun say? thanks
It should say around 7.5 at idle for a DVDA. However, max advance at approximately 3k rpm should be 28 to 32 atdc. Having max advance in the correct spot is more important than what it does at idle.
Lol. It's because the distributor clamp is too close to the nut to get a socket on it. I have since changed to a type 3 clamp which moves the nut to the left side of the distributor.
I will say that I do not think the vast majority of people will need to perform a static time, a total centrifugal advance time, an SVDA advance-only time, and a full DVDA time on their engine in order to dial it in. But man, you did an outstanding job on this video so everyone should be able to time their engine wherever it sits currently. Thank you!
Awesome Explanation. This is the only DVDA setup I’ve seen that makes perfect sense. Much appreciated! Just ordered a remanufactured distributor from VWNOS…Many Thanks!!!
This video was one of the best videos I have EVER seen on timing. Thanks a million! I have a DVDA with pertronix ignition and I have been having trouble with tuning because I have been timing my max adv with the hose connected. I think this will solve my problem and I can't thank you enough for the insight!
I agree, that was brilliant, a little closer would be the only thing I could think would make it better. But only because I'm a "Green as Kermit" rookie ...Lol
awesome video, most helpful one i've seen on timing
Seriously, good information. Use a sharpie to mark the dist position. Then you will know exactly if it moved when tightening down.
Tks bro it's wonderful to caching this work over and over we can understand .
Thanks for posting this, I also have the same carb as yours and needed to know how to do it, great job.
I have a SVDA 034 with electronic ignition, but I haven't built up the confidence to change it and time it and all that. Kinda unsure whether I need to change coil or not. I have the stock black Bosch from 1969. I believe they have a built in ballast resistance but I'm not sure. Don't regular distributors with points require a ballast resistor? If so I'm good to go. Self-doubt is my worst enemy. Thank you so much for this video.
I have DVDA as well, hard to find this "Know How", thanks a lot!!!
Nice video.
Did you have both vacuum ports on the carb plugged for initial timing?
when you time it at max advance at 30 degrees 3000rpm,, what is that actually ignition timing when you measure it at idle. so at idle point the gun at the block casing marker and get the tdc mark to line up, whats the gun say?
thanks
It should say around 7.5 at idle for a DVDA. However, max advance at approximately 3k rpm should be 28 to 32 atdc. Having max advance in the correct spot is more important than what it does at idle.
He lost his 10 mm socket!😝
Lol. It's because the distributor clamp is too close to the nut to get a socket on it. I have since changed to a type 3 clamp which moves the nut to the left side of the distributor.
😀
Where is the retardant hose connected on the other side. Can’t see it in the video.
It connects to the rear (rear is rear) of the carb. Like this www.thesamba.com/vw/gallery/pix/2057674.jpg
@@timothyb8281 thanks